Nedis WIFIDS10WT Tasmota Configuration

gistfile1.txt

{"NAME":"Nedis WIFIDS10WT","GPIO":[0,107,0,108,0,0,0,0,0,0,0,0,0],"FLAG":0,"BASE":54}

Module 54

Backlog TuyaMCU 11,4; TuyaMCU 51,51

Backlog SetOption1 1; SetOption65 1; SetOption66 1

Rule1 
 ON TuyaReceived#Data=55AA000500056A0400010078 DO publish2 stat/%topic%/FIRE OFF ENDON
 ON TuyaReceived#Data=55AA000500056A0400010078 DO publish2 stat/%topic%/TEST OFF ENDON
 ON TuyaReceived#Data=55AA000500056A0400010078 DO publish2 stat/%topic%/BATTERY OFF ENDON
 ON TuyaReceived#Data=55AA000500056A0400010078 DO publish2 stat/%topic%/MUTE OFF ENDON
 ON TuyaReceived#Data=55AA000500056A0400010179 DO publish2 stat/%topic%/FIRE ON ENDON
 ON TuyaReceived#Data=55AA000500056A0400010179 DO publish2 stat/%topic%/MUTE OFF ENDON
 ON TuyaReceived#Data=55AA000500056A040001027A DO publish2 stat/%topic%/FIRE ON ENDON
 ON TuyaReceived#Data=55AA000500056A040001027A DO publish2 stat/%topic%/MUTE ON ENDON
 ON TuyaReceived#Data=55AA000500056A040001037B DO publish2 stat/%topic%/FIRE ON ENDON
 ON TuyaReceived#Data=55AA000500056A040001037B DO publish2 stat/%topic%/TEST ON ENDON
 ON TuyaReceived#Data=55AA000500056A040001037B DO publish2 stat/%topic%/MUTE OFF ENDON
 ON TuyaReceived#Data=55AA000500056A040001047C DO publish2 stat/%topic%/BATTERY ON ENDON
 
Rule2
 ON system#boot do publish2 homeassistant/binary_sensor/%macaddr%_fire/config {"name":"Office Fire Alarm","state_topic":"stat/%topic%/FIRE","device_class":"smoke","unique_id":"%macaddr%_fire","device":{"connections":[["mac","%macaddr%"]]}} ENDON
 ON system#boot do publish2 homeassistant/binary_sensor/%macaddr%_test/config {"name":"Office Fire Alarm Test","state_topic":"stat/%topic%/TEST","icon":"mdi:bell-alert","unique_id":"%macaddr%_test","device":{"connections":[["mac","%macaddr%"]]}} ENDON
 ON system#boot do publish2 homeassistant/binary_sensor/%macaddr%_mute/config {"name":"Office Fire Alarm Mute","state_topic":"stat/%topic%/MUTE","icon":"mdi:bell-sleep","unique_id":"%macaddr%_mute","device":{"connections":[["mac","%macaddr%"]]}} ENDON
 ON system#boot do publish2 homeassistant/binary_sensor/%macaddr%_battery/config {"name":"Office Fire Alarm Battery","state_topic":"stat/%topic%/BATTERY","device_class":"battery","unique_id":"%macaddr%_battery","device":{"connections":[["mac","%macaddr%"]]}} ENDON

Hi @PaulUitWijchen, the device works kind of odd like that. The wifi module stays off by default.

It gets turned on when:

1. there's smoke detected (duh)
2. when the test button is held (it emits the test message)
3. when you hit the test button 3 times in one second (this should trigger pairing mode with the original firmware, however pairing is not necessary when you've flashed tasmota)
4. periodically when low battery is detected (with the relevant low battery message)
5. weekly to report its condition is normal (with a generic no fire detected message)

When the wifi module gets turned on, the other MCU on the smoke detector sends a message to it using the Tuya protocol. The rules above get triggered only when such a message is received. In other words, try to trigger the test functionality and listen in on your MQTT topic and see what comes in. You will not receive any status updates otherwise.

Oh and also you should be able to see the raw tuya messages by listening to the tele/%topic%/RESULT topic

thanks for the reply.
I flash the device again and reloaded the software. If I press the test button then I see in HA a report of the SSID, address and that sort of things, until the red light dims. Still the other Fire Alarm, Battery remains unknown.
In MQTT Exporer I see tele/tasmota_nnn/INFO1 2 and 3 and then
tele/tasmota_313159/STATE, but no result.
So if I press the button, shhould it then also send this message? Or only weekly?
-- Paul