Last active
August 26, 2022 13:20
-
-
Save igoro00/3171a408e1f80ee77b8619aaa9e4df0f to your computer and use it in GitHub Desktop.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by PrusaSlicer 2.5.0-rc1+win64 on 2022-08-26 at 13:17:30 UTC | |
| [print:Sapphire Pro] | |
| avoid_crossing_perimeters = 1 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = monotonic | |
| bottom_solid_layers = 4 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 80 | |
| brim_separation = 0 | |
| brim_type = outer_only | |
| brim_width = 0 | |
| clip_multipart_objects = 1 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| draft_shield = disabled | |
| elefant_foot_compensation = 0.2 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 40 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 30% | |
| fill_pattern = stars | |
| first_layer_acceleration = 0 | |
| first_layer_acceleration_over_raft = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 15 | |
| first_layer_speed_over_raft = 30 | |
| fuzzy_skin = none | |
| fuzzy_skin_point_dist = 0.8 | |
| fuzzy_skin_thickness = 0.3 | |
| gap_fill_enabled = 1 | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| gcode_resolution = 0.0125 | |
| gcode_substitutions = | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 60 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.2 | |
| max_print_speed = 250 | |
| max_volumetric_extrusion_rate_slope_negative = 0 | |
| max_volumetric_extrusion_rate_slope_positive = 0 | |
| max_volumetric_speed = 8 | |
| min_bead_width = 85% | |
| min_feature_size = 25% | |
| min_skirt_length = 0 | |
| mmu_segmented_region_max_width = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_generator = arachne | |
| perimeter_speed = 60 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_contact_distance = 0.2 | |
| raft_expansion = 0 | |
| raft_first_layer_density = 90% | |
| raft_first_layer_expansion = 3 | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| slicing_mode = regular | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 60 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 1 | |
| support_material_bottom_contact_distance = 0 | |
| support_material_bottom_interface_layers = -1 | |
| support_material_buildplate_only = 1 | |
| support_material_closing_radius = 2 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_pattern = rectilinear | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_style = grid | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thick_bridges = 1 | |
| thin_walls = 1 | |
| threads = 4 | |
| top_fill_pattern = monotonic | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 60 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 130 | |
| travel_speed_z = 0 | |
| wall_distribution_count = 1 | |
| wall_transition_angle = 10 | |
| wall_transition_filter_deviation = 25% | |
| wall_transition_length = 100% | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_brim_width = 2 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = 0 | |
| [print:Sapphire Pro Quality] | |
| avoid_crossing_perimeters = 1 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = monotonic | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_separation = 0 | |
| brim_type = outer_only | |
| brim_width = 0 | |
| clip_multipart_objects = 1 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| draft_shield = disabled | |
| elefant_foot_compensation = 0.2 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = stars | |
| first_layer_acceleration = 0 | |
| first_layer_acceleration_over_raft = 0 | |
| first_layer_extrusion_width = 0.42 | |
| first_layer_height = 0.1 | |
| first_layer_speed = 30 | |
| first_layer_speed_over_raft = 30 | |
| fuzzy_skin = none | |
| fuzzy_skin_point_dist = 0.8 | |
| fuzzy_skin_thickness = 0.3 | |
| gap_fill_enabled = 1 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| gcode_resolution = 0.0125 | |
| gcode_substitutions = | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 60 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.1 | |
| max_print_speed = 80 | |
| max_volumetric_extrusion_rate_slope_negative = 0 | |
| max_volumetric_extrusion_rate_slope_positive = 0 | |
| max_volumetric_speed = 0 | |
| min_bead_width = 85% | |
| min_feature_size = 25% | |
| min_skirt_length = 0 | |
| mmu_segmented_region_max_width = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_generator = arachne | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_contact_distance = 0.1 | |
| raft_expansion = 1.5 | |
| raft_first_layer_density = 90% | |
| raft_first_layer_expansion = 3 | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| slicing_mode = regular | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 1 | |
| support_material_bottom_contact_distance = 0 | |
| support_material_bottom_interface_layers = -1 | |
| support_material_buildplate_only = 1 | |
| support_material_closing_radius = 2 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_pattern = rectilinear | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_style = grid | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thick_bridges = 1 | |
| thin_walls = 1 | |
| threads = 4 | |
| top_fill_pattern = monotonic | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 5 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 130 | |
| travel_speed_z = 0 | |
| wall_distribution_count = 1 | |
| wall_transition_angle = 10 | |
| wall_transition_filter_deviation = 25% | |
| wall_transition_length = 100% | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_brim_width = 2 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = 0 | |
| [filament:Print-Me rPETG] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #1A5FB4 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 1.04 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.7 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PET | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 230 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 15 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode" | |
| temperature = 230 | |
| [filament:Sapphire Pro] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 0.97 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = 6 | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = 40 | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 190 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 15 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 190 | |
| [filament:Sapphire Pro - Devil Design PETG] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1.01 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #1A5FB4 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 1.04 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PET | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 75 | |
| first_layer_temperature = 230 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 50 | |
| min_fan_speed = 15 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 230 | |
| [filament:Sapphire Pro 3DACTIVE Marble PLA] | |
| bed_temperature = 70 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #C0BFBC | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 70 | |
| filament_density = 1.22 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 8 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 70 | |
| first_layer_temperature = 210 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 100 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:Sapphire Pro Easy PLA] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #77767B | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 70 | |
| filament_density = 1.22 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 190 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 100 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 190 | |
| [filament:petg] | |
| bed_temperature = 0 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 10 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PET | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 0 | |
| first_layer_temperature = 200 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 200 | |
| [printer:Sapphire Pro] | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 0x0,210x0,210x175,0x175 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| color_change_gcode = M600 | |
| cooling_tube_length = 5 | |
| cooling_tube_retraction = 91.5 | |
| default_filament_profile = | |
| default_print_profile = | |
| deretract_speed = 0 | |
| end_gcode = M104 S0 ; turn off temperature\nM140 S0; turn off bed\nG0 X5 Y0\nM84 ; disable motors\nNOKIA | |
| extra_loading_move = -2 | |
| extruder_colour = "" | |
| extruder_offset = 0x0 | |
| gcode_flavor = marlin | |
| high_current_on_filament_swap = 0 | |
| host_type = octoprint | |
| inherits = | |
| layer_gcode = | |
| machine_limits_usage = time_estimate_only | |
| machine_max_acceleration_e = 10000,5000 | |
| machine_max_acceleration_extruding = 99999,1250 | |
| machine_max_acceleration_retracting = 1500,1250 | |
| machine_max_acceleration_travel = 1500,1250 | |
| machine_max_acceleration_x = 9000,1000 | |
| machine_max_acceleration_y = 9000,1000 | |
| machine_max_acceleration_z = 500,200 | |
| machine_max_feedrate_e = 120,120 | |
| machine_max_feedrate_x = 500,200 | |
| machine_max_feedrate_y = 500,200 | |
| machine_max_feedrate_z = 12,12 | |
| machine_max_jerk_e = 2.5,2.5 | |
| machine_max_jerk_x = 10,10 | |
| machine_max_jerk_y = 10,10 | |
| machine_max_jerk_z = 0.2,0.4 | |
| machine_min_extruding_rate = 0,0 | |
| machine_min_travel_rate = 0,0 | |
| max_layer_height = 0 | |
| max_print_height = 200 | |
| min_layer_height = 0.07 | |
| nozzle_diameter = 0.6 | |
| parking_pos_retraction = 92 | |
| pause_print_gcode = M601 | |
| print_host = | |
| printer_model = | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = FFF | |
| printer_variant = | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| remaining_times = 0 | |
| retract_before_travel = 2 | |
| retract_before_wipe = 0% | |
| retract_layer_change = 0 | |
| retract_length = 1 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| silent_mode = 1 | |
| single_extruder_multi_material = 0 | |
| start_gcode = M104 S[first_layer_temperature] ; set hotend temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for hotend temp\nG28 ; home all axes\n;G29\n\nG92 E0\nG1 Y3.0 X200.0 Z0.4 F4000.0 ;go to start of purge line\nG1 X100.0 E15.0 F1000.0 ;start purge line\nG1 X10.0 E30.0 F1000.0 ;finish pur;ge line\n\n;SET_PRESSURE_ADVANCE EXTRUDER=extruder ADVANCE=0.000 | |
| template_custom_gcode = | |
| thumbnails = | |
| thumbnails_format = PNG | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| variable_layer_height = 1 | |
| wipe = 0 | |
| z_offset = 0 | |
| [physical_printer:Sapphire Pro] | |
| host_type = octoprint | |
| preset_name = Sapphire Pro | |
| preset_names = "Sapphire Pro" | |
| print_host = http://printer.local | |
| printer_technology = FFF | |
| printhost_apikey = 4AA761A9676B4537BAFD7F155C580BCC | |
| printhost_authorization_type = key | |
| printhost_cafile = | |
| printhost_password = | |
| printhost_port = | |
| printhost_ssl_ignore_revoke = 0 | |
| printhost_user = | |
| [presets] | |
| print = Sapphire Pro | |
| sla_print = | |
| sla_material = | |
| printer = Sapphire Pro | |
| filament = Sapphire Pro 3DACTIVE Marble PLA | |
| physical_printer = Sapphire Pro |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment