-
-
Save jazzsequence/36600abb8f0655a63724fbe046899deb to your computer and use it in GitHub Desktop.
| ; Ender 5 Custom End G-code | |
| G4 ; Wait | |
| M220 S100 ; Reset Speed factor override percentage to default (100%) | |
| M221 S100 ; Reset Extrude factor override percentage to default (100%) | |
| G91 ; Set coordinates to relative | |
| G1 F1800 E-3 ; Retract filament 3 mm to prevent oozing | |
| G1 F3000 Z20 ; Move Z Axis up 20 mm to allow filament ooze freely | |
| G90 ; Set coordinates to absolute | |
| G1 X0 Y220 F1000 ; Move Heat Bed to the front for easy print removal | |
| M106 S0 ; Turn off cooling fan | |
| M104 S0 ; Turn off extruder | |
| M140 S0 ; Turn off bed | |
| M107 ; Turn off Fan | |
| M84 ; Disable stepper motors | |
| M117 That's All Folks! | |
| ; End of custom end GCode |
| ; Ender 5 Custom Start G-code | |
| M104 S200 ; Set Extruder temperature to 200. | |
| M140 S70 ; Set Heat Bed temperature to 70 | |
| ; 50 should be sufficient for the actual build but raising the temp can help builds stick to the base. | |
| M190 S50 ; Wait for Heat Bed temperature. | |
| M109 S200 ; Wait for Extruder temperature | |
| G28 ; Home all axes | |
| M117 ; Purge extruder | |
| G92 E0 ; Reset Extruder | |
| ; Draw a line. This is for the test line, so it can be a little lower than we need. | |
| G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed. | |
| G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position | |
| G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line | |
| G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little | |
| G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line | |
| G92 E0 ; Reset Extruder | |
| G1 Z1.5 F3000 ; Move Z Axis up to where it should be for the actual print. | |
| M117 By your command! | |
| ; End of custom start GCode |
Will this code work with the Ender 5 plus?
Also, I have the Creality Silent board + Added the Microswiss Direct Drive extruder. Do any of the settings need to be adjusted?
I actually use this on my ender 5 pro with microswiss DD and my ender 7.
Will this code work with the Ender 5 plus?
Also, I have the Creality Silent board + Added the Microswiss Direct Drive extruder. Do any of the settings need to be adjusted?I actually use this on my ender 5 pro with microswiss DD and my ender 7.
And? How was going? I have also new ender 5 pro and i would like to try this code.
Will this code work with the Ender 5 plus?
Also, I have the Creality Silent board + Added the Microswiss Direct Drive extruder. Do any of the settings need to be adjusted?I actually use this on my ender 5 pro with microswiss DD and my ender 7.
And? How was going? I have also new ender 5 pro and i would like to try this code.
Works fine. No issues at all.
Not sure when this started, but Cura 5.8.1 does wait for bed / nozzle temperature in filament settings.
We just have home and purge in start gcode.
Will this code work with the Ender 5 plus?
Also, I have the Creality Silent board + Added the Microswiss Direct Drive extruder. Do any of the settings need to be adjusted?