Created
May 19, 2011 14:17
-
-
Save jmccrohan/980837 to your computer and use it in GitHub Desktop.
OpenWrt BT Voyager 2110
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| CFE version 1.0.37-6.8.5CFE version 1.0.37-6.8.5 for BCM96348 (32bit,SP,BE) | |
| Build Date: Tue Jan 2 19:44:45 CST 2007 (michaelc) | |
| Boot Address 0xbfc00000 | |
| Flash Config: CS0(1fc00009,1f),Base(bfc00000),Size(4MB) | |
| Ethernet Switch Mode 00000000 | |
| found@block 8 | |
| Board IP address : 192.168.1.1 | |
| Host IP address : 192.168.1.2 | |
| Gateway IP address : | |
| Run from flash/host (f/h) : f | |
| Default host run file name : vmlinux | |
| Default host flash file name : bcmModelName_fs_kernel | |
| Boot delay (0-9 seconds) : 5 | |
| Board Id Name : V2110 | |
| Psi size in KB : 24 | |
| Number of MAC Addresses (1-32) : 2 | |
| Ethernet MAC Address : 00:16:e3:32:75:d2 | |
| Serial Number : | |
| WEP 128bit Key : 0000000000000 | |
| Memory size in MB : 16 | |
| CMT Thread Number : 0 | |
| ==== Press space key to stop auto run (5 seconds) ==== | |
| Auto run second count down(before hit space key): 5 | |
| CFE> f 192.168.1.99:openwrt-BTV2110-squashfs-cfe.bin | |
| Loading 192.168.1.99:openwrt-BTV2110-squashfs-cfe.bin ... | |
| Finished loading 2293764 bytes | |
| Flashing root file system and kernel@0xbfc10000 .................................... | |
| done ! | |
| Resetting board...ÿ | |
| CFE version 1.0.37-6.8.5CFE version 1.0.37-6.8.5 for BCM96348 (32bit,SP,BE) | |
| Build Date: Tue Jan 2 19:44:45 CST 2007 (michaelc) | |
| Boot Address 0xbfc00000 | |
| Flash Config: CS0(1fc00009,1f),Base(bfc00000),Size(4MB) | |
| Ethernet Switch Mode 00000000 | |
| found@block 8 | |
| Board IP address : 192.168.1.1 | |
| Host IP address : 192.168.1.2 | |
| Gateway IP address : | |
| Run from flash/host (f/h) : f | |
| Default host run file name : vmlinux | |
| Default host flash file name : bcmModelName_fs_kernel | |
| Boot delay (0-9 seconds) : 5 | |
| Board Id Name : V2110 | |
| Psi size in KB : 24 | |
| Number of MAC Addresses (1-32) : 2 | |
| Ethernet MAC Address : 00:16:e3:32:75:d2 | |
| Serial Number : | |
| WEP 128bit Key : 0000000000000 | |
| Memory size in MB : 16 | |
| CMT Thread Number : 0 | |
| ==== Press space key to stop auto run (5 seconds) ==== | |
| Auto run second count down(before hit space key): 0 | |
| Code Address: 0x80010000, Entry Address: 0x80010000 | |
| Decompression OK! | |
| Entry at 0x80010000 | |
| Closing network. | |
| Starting program at 0x80010000 | |
| Linux version 2.6.37.6 (jmccrohan@lambda) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #5 Thu May 19 01:04:56 IST 2011 | |
| Detected Broadcom 0x6348 CPU revision b0 | |
| CPU frequency is 240 MHz | |
| 16MB of RAM installed | |
| registering 37 GPIOs | |
| board_bcm963xx: CFE version: 1.0.37-6.8 | |
| bootconsole [early0] enabled | |
| CPU revision is: 00029107 (Broadcom BMIPS3300) | |
| board_bcm963xx: board name: V2110 | |
| Determined physical RAM map: | |
| memory: 01000000 @ 00000000 (usable) | |
| Initrd not found or empty - disabling initrd | |
| Zone PFN ranges: | |
| Normal 0x00000000 -> 0x00001000 | |
| Movable zone start PFN for each node | |
| early_node_map[1] active PFN ranges | |
| 0: 0x00000000 -> 0x00001000 | |
| Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 | |
| Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 | |
| PID hash table entries: 64 (order: -4, 256 bytes) | |
| Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
| Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes. | |
| Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes | |
| Memory: 13396k/16384k available (2045k kernel code, 2988k reserved, 348k data, 164k init, 0k highmem) | |
| NR_IRQS:128 | |
| Calibrating delay loop... 239.10 BogoMIPS (lpj=478208) | |
| pid_max: default: 32768 minimum: 301 | |
| Mount-cache hash table entries: 512 | |
| NET: Registered protocol family 16 | |
| board_bcm963xx: not enough mac address | |
| registering PCI controller with io_map_base unset | |
| bio: create slab <bio-0> at 0 | |
| pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff] | |
| pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x30001fff] (PCI address [0x30000000-0x30001fff]) | |
| Switching to clocksource MIPS | |
| PCI: Enabling device 0000:00:01.0 (0000 -> 0002) | |
| ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | |
| TCP established hash table entries: 512 (order: 0, 4096 bytes) | |
| TCP bind hash table entries: 512 (order: -1, 2048 bytes) | |
| TCP: Hash tables configured (established 512 bind 512) | |
| TCP reno registered | |
| UDP hash table entries: 256 (order: 0, 4096 bytes) | |
| UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | |
| NET: Registered protocol family 1 | |
| audit: initializing netlink socket (disabled) | |
| type=2000 audit(0.356:1): initialized | |
| squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
| msgmni has been set to 26 | |
| io scheduler noop registered | |
| io scheduler deadline registered (default) | |
| gpiodev: gpio device registered with major 254 | |
| bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart | |
| console [ttyS0] enabled, bootconsole disabled | |
| console [ttyS0] enabled, bootconsole disabled | |
| bcm963xx-flash bcm963xx-flash.0: 0x00400000 at 0x1fc00000 | |
| bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a00 | |
| Amd/Fujitsu Extended Query Table at 0x0040 | |
| Amd/Fujitsu Extended Query version 1.3. | |
| number of CFI chips: 1 | |
| bcm963xx_flash: Read Signature value of CFE1CFE1 | |
| bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected | |
| bcm963xx_flash: CFE boot tag found with version 6 and board type V2110 | |
| bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000 | |
| bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00 | |
| bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000 | |
| bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000 | |
| bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000 | |
| bcm963xx_flash: Spare partition is 250000 offset and length 1a0000 | |
| Creating 5 MTD partitions on "bcm963xx": | |
| 0x000000000000-0x000000010000 : "CFE" | |
| 0x000000010100-0x0000000f0000 : "kernel" | |
| mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only | |
| 0x0000000f0000-0x0000003f0000 : "rootfs" | |
| mtd: partition "rootfs" set to be root filesystem | |
| mtd: partition "rootfs_data" created automatically, ofs=240000, len=1B0000 | |
| 0x000000240000-0x0000003f0000 : "rootfs_data" | |
| 0x0000003f0000-0x000000400000 : "nvram" | |
| 0x000000010000-0x0000003f0000 : "linux" | |
| bcm63xx_enet MII bus: probed | |
| bcm63xx-wdt bcm63xx-wdt.0: started, timer margin: 30 sec | |
| TCP westwood registered | |
| NET: Registered protocol family 17 | |
| 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> | |
| All bugs added by David S. Miller <[email protected]> | |
| VFS: Mounted root (squashfs filesystem) readonly on device 31:2. | |
| Freeing unused kernel memory: 164k freed | |
| awk: /proc/cpuinfo: No such file or directory | |
| awk: /proc/cpuinfo: No such file or directory | |
| roboswitch: Probing device eth0: | |
| roboswitch: [/home/jmccrohan/openwrt/trunk/build_dir/linux-brcm63xx/kmod-switch/switch-robo.c:125] SIOCGETCPHYRD failed! | |
| roboswitch: [/home/jmccrohan/openwrt/trunk/build_dir/linux-brcm63xx/kmod-switch/switch-robo.c:125] SIOCGETCPHYRD failed! | |
| No Robo switch in managed mode found, phy_id = 0xffffffff | |
| roboswitch: Probing device eth1: No such device | |
| roboswitch: Probing device eth2: No such device | |
| roboswitch: Probing device eth3: No such device | |
| - preinit - | |
| Press the [f] key and hit [enter] to enter failsafe mode | |
| - regular preinit - | |
| JFFS2 notice: (265) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 3 of xref (0 dead, 2 orphan) found. | |
| switching to jffs2 | |
| - init - | |
| Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)] | |
| Compat-wireless backport release: compat-wireless-2011-05-11-1-g501c91f | |
| Backport based on wireless-testing.git master-2011-05-13 | |
| cfg80211: Calling CRDA to update world regulatory domain | |
| There is already a switch registered on the device 'eth0' | |
| roboswitch: Probing device eth1: No such device | |
| roboswitch: Probing device eth2: No such device | |
| roboswitch: Probing device eth3: No such device | |
| cfg80211: World regulatory domain updated: | |
| cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) | |
| cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) | |
| cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) | |
| cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) | |
| cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) | |
| cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) | |
| b43-phy0: Broadcom 4318 WLAN found (core revision 9) | |
| Broadcom 43xx driver loaded [ Features: PL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ] | |
| PPP generic driver version 2.4.2 | |
| ip_tables: (C) 2000-2006 Netfilter Core Team | |
| NET: Registered protocol family 24 | |
| nf_conntrack version 0.5.0 (211 buckets, 844 max) | |
| BusyBox v1.18.4 (2011-05-18 21:35:51 IST) built-in shell (ash) | |
| Enter 'help' for a list of built-in commands. | |
| _______ ________ __ | |
| | |.-----.-----.-----.| | | |.----.| |_ | |
| | - || _ | -__| || | | || _|| _| | |
| |_______|| __|_____|__|__||________||__| |____| | |
| |__| W I R E L E S S F R E E D O M | |
| ATTITUDE ADJUSTMENT (bleeding edge, r26936) ---------- | |
| * 1/4 oz Vodka Pour all ingredients into mixing | |
| * 1/4 oz Gin tin with ice, strain into glass. | |
| * 1/4 oz Amaretto | |
| * 1/4 oz Triple sec | |
| * 1/4 oz Peach schnapps | |
| * 1/4 oz Sour mix | |
| * 1 splash Cranberry juice | |
| ----------------------------------------------------- | |
| root@OpenWrt:/# |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment