this gist is part of this series
This fixes issues i bugged with the thunderbolt / thunderbolt-net maintainers (i will take everyones thanks now, lol)
- install lldpctl with
apt install lldpd
- add
thunderboltandthunderbolt-netkernel modules (this must be done all nodes - yes i know it can sometimes work withoutm but the thuderbolt-net one has interesting behaviou' so do as i say - add both ;-)nano /etc/modulesadd modules at bottom of file, one on each line- save using
xthenythenenter
doing this means we don't have to give each thunderbolt a manual IPv6 addrees and that these addresses stay constant no matter what
Add the following to each node using nano /etc/network/interfaces
If you see any sections called thunderbolt0 or thunderbol1 delete them at this point.
Doing this means we don't have to give each thunderbolt a manual IPv6 or IPv4 addrees and that these addresses stay constant no matter what.
Add the following to each node using nano /etc/network/interfaces this to remind you not to edit en05 and en06 in the GUI
This fragment should go between the existing auto lo section and adapater sections.
iface en05 inet manual
#do not edit it GUI
iface en06 inet manual
#do not edit in GUI
If you see any thunderbol sections delete them from the file before you save it.
*DO NOT DELETE the source /etc/network/interfaces.d/* this will always exist on the latest versions and should be the last or next to last line in /interfaces file
This is needed as proxmox doesn't recognize the thunderbolt interface name. There are various methods to do this. This method was selected after trial and error because:
- the thunderboltX naming is not fixed to a port (it seems to be based on sequence you plug the cables in)
- the MAC address of the interfaces changes with most cable insertion and removale events
-
use
udevadm monitorcommand to find your device IDs when you insert and remove each TB4 cable. Yes you can use other ways to do this, i recommend this one as it is great way to understand what udev does - the command proved more useful to me thanthe syslogorlspci commandfor troublehsooting thunderbolt issues and behavious. In my case my two pci paths are0000:00:0d.2and0000:00:0d.3if you bought the same hardware this will be the same on all 3 units. Don't assume your PCI device paths will be the same as mine. -
create a link file using
nano /etc/systemd/network/00-thunderbolt0.linkand enter the following content:
[Match]
Path=pci-0000:00:0d.2
Driver=thunderbolt-net
[Link]
MACAddressPolicy=none
Name=en05
- create a second link file using
nano /etc/systemd/network/00-thunderbolt1.linkand enter the following content:
[Match]
Path=pci-0000:00:0d.3
Driver=thunderbolt-net
[Link]
MACAddressPolicy=none
Name=en06
This section en sure that the interfaces will be brought up at boot or cable insertion with whatever settings are in /etc/network/interfaces - this shouldn't need to be done, it seems like a bug in the way thunderbolt networking is handled (i assume this is debian wide but haven't checked).
- create a udev rule to detect for cable insertion using
nano /etc/udev/rules.d/10-tb-en.ruleswith the following content:
ACTION=="move", SUBSYSTEM=="net", KERNEL=="en05", RUN+="/usr/local/bin/pve-en05.sh"
ACTION=="move", SUBSYSTEM=="net", KERNEL=="en06", RUN+="/usr/local/bin/pve-en06.sh"
-
save the file
-
create the first script referenced above using
nano /usr/local/bin/pve-en05.shand with the follwing content:
#!/bin/bash
# this brings the renamed interface up and reprocesses any settings in /etc/network/interfaces for the renamed interface
/usr/sbin/ifup en05
save the file and then
- create the second script referenced above using
nano /usr/local/bin/pve-en06.shand with the follwing content:
#!/bin/bash
# this brings the renamed interface up and reprocesses any settings in /etc/network/interfaces for the renamed interface
/usr/sbin/ifup en06
and save the file
- make both scripts executable with
chmod +x /usr/local/bin/*.sh - run
update-initramfs -u -k allto propogate the new link files into initramfs - Reboot (restarting networking, init 1 and init 3 are not good enough, so reboot)
if you are having speed issues make sure the following is set on the kernel command line in /etc/default/grub file
intel_iommu=on iommu=pt
one set be sure to run update-grub and reboot
everyones grub command line is different this is mine because i also have i915 virtualization, if you get this wrong you can break your machine, if you are not doing that you don't need the i915 entries you see below
GRUB_CMDLINE_LINUX_DEFAULT="quiet intel_iommu=on iommu=pt" (note if you have more things in your cmd line DO NOT REMOVE them, just add the two intel ones, doesnt matter where.
I have only tried this on 6.8 kernels, so YMMV If you want more TB messages in dmesg to see why connection might be failing here is how to turn on dynamic tracing
For bootime you will need to add it to the kernel command line by adding thunderbolt.dyndbg=+p to your /etc/default/grub file, running update-grub and rebooting.
To expand the example above"
`GRUB_CMDLINE_LINUX_DEFAULT="quiet intel_iommu=on iommu=pt thunderbolt.dyndbg=+p"`
Don't forget to run update-grub after saving the change to the grub file.
For runtime debug you can run the following command (it will revert on next boot) so this cant be used to cpature what happens at boot time.
`echo -n 'module thunderbolt =p' > /sys/kernel/debug/dynamic_debug/control`
these tools can be used to inspect your thundebolt system, note they rely on rust to be installedm you must use the rustup script below and not intsall rust by package manager at this time (9/15/24)
apt install pkg-config libudev-dev git curl
curl https://sh.rustup.rs -sSf | sh
git clone https://github.com/intel/tbtools
restart you ssh session
cd tbtools
cargo install --path .