justheath

[virtual_sdcard]
path: /home/pi/gcode_files

[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE

justheath

# This file came from https://github.com/Klipper3d/klipper/blob/master/config/generic-creality-v4.2.7.cfg

# This file contains pin mappings for the Creality "v4.2.7" board. To
# use this config, during "make menuconfig" select the STM32F103 with
# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.

# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.

justheath

# Let's see if putting macros in a separate file is helpful

# ------------------------- Filament Change --------------------------
# M600: Filament Change. This macro will pause the printer, move the
# tool to the change position, and retract the filament 50mm. Adjust
# the retraction settings for your own extruder. After filament has
# been changed, the print can be resumed from its previous position
# with the "RESUME" gcode.

[gcode_macro M600]

justheath

# Note: variables used below should be same as those in the [START/END]_PRINT macros.

#### CURA Start and End G-code for use with Klipper

# Start G-Code
# Pass the filament's temperature values
SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=bed_temp VALUE={material_bed_temperature_layer_0}
SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_temp VALUE={material_print_temperature_layer_0}
# calls the Klipper macro to prepare extruder and bed
START_PRINT

justheath

# This file came from https://github.com/Klipper3d/klipper/blob/master/config/generic-creality-v4.2.7.cfg

# This file contains pin mappings for the Creality "v4.2.7" board. To
# use this config, during "make menuconfig" select the STM32F103 with
# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.

# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.

justheath

# these are needed by mainsail macros
[gcode_macro _CLIENT_VARIABLE]
variable_use_custom_pos  : False ; use custom park coordinates for x,y [True/False] 
variable_custom_park_x   : 0.0   ; custom x position; value must be within your defined min and max of X
variable_custom_park_y   : 0.0   ; custom y position; value must be within your defined min and max of Y
variable_custom_park_dz  : 2.0   ; custom dz value; the value in mm to lift the nozzle when move to park position 
variable_retract         : 1.0   ; the value to retract while PAUSE
variable_cancel_retract  : 5.0   ; the value to retract while CANCEL_PRINT
variable_speed_retract   : 35.0  ; retract speed in mm/s
variable_unretract       : 1.0   ; the value to unretract while RESUME

justheath

#### crowsnest.conf
#### This is a typical default config.
#### Also used as default in mainsail / MainsailOS
#### See:
#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md
#### for details to configure to your needs.


#####################################################################
####                                                            #####