ipq5018.dtsi

ipq5018.dtsi

// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
 * IPQ5018 SoC device tree source
 *
 * Copyright (c) 2023-2025 The Linux Foundation. All rights reserved.
 */

#include <dt-bindings/clock/qcom,apss-ipq.h>
#include <dt-bindings/clock/qcom,gcc-ipq5018.h>
#include <dt-bindings/clock/qcom,ipq5018-cmn-pll.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/qcom,gcc-ipq5018.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;
	#address-cells = <2>;
	#size-cells = <2>;

	clocks {
		cmn_pll_ref_clk: cmn-pll-ref-clk {
			compatible = "fixed-clock";
			clock-frequency = <96000000>;
			#clock-cells = <0>;
		};

		gephy_rx_clk: gephy-rx-clk {
			compatible = "fixed-clock";
			clock-frequency = <125000000>;
			#clock-cells = <0>;
		};

		gephy_tx_clk: gephy-tx-clk {
			compatible = "fixed-clock";
			clock-frequency = <125000000>;
			#clock-cells = <0>;
		};

		ref_96mhz_clk: ref-96mhz-clk {
			compatible = "fixed-factor-clock";
			clocks = <&xo_clk>;
			#clock-cells = <0>;
			clock-div = <1>;
			clock-mult = <2>;
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
		};

		xo_board_clk: xo-board-clk {
			compatible = "fixed-factor-clock";
			clocks = <&ref_96mhz_clk>;
			#clock-cells = <0>;
		};

		xo_clk: xo-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <48000000>;
		};
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x0>;
			enable-method = "psci";
			next-level-cache = <&l2_0>;
			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
			operating-points-v2 = <&cpu_opp_table>;
			#cooling-cells = <2>;
		};

		cpu1: cpu@1 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x1>;
			enable-method = "psci";
			next-level-cache = <&l2_0>;
			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
			operating-points-v2 = <&cpu_opp_table>;
			#cooling-cells = <2>;
		};

		l2_0: l2-cache {
			compatible = "cache";
			cache-level = <2>;
			cache-size = <0x80000>;
			cache-unified;
		};
	};

	cpu_opp_table: opp-table-cpu {
		compatible = "operating-points-v2";
		opp-shared;

		opp-800000000 {
			opp-hz = /bits/ 64 <800000000>;
			opp-microvolt = <1100000>;
			clock-latency-ns = <200000>;
		};

		opp-1008000000 {
			opp-hz = /bits/ 64 <1008000000>;
			opp-microvolt = <1100000>;
			clock-latency-ns = <200000>;
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-ipq5018", "qcom,scm";
			qcom,dload-mode = <&tcsr 0x6100>;
			qcom,sdi-enabled;
		};
	};

	memory@40000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0x0 0x40000000 0x0 0x0>;
	};

	pmu {
		compatible = "arm,cortex-a53-pmu";
		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		tz_apps@4a400000 {
			reg = <0x0 0x4a400000 0x0 0x400000>;
			no-map;
		};

		bootloader_region: bootloader@4a800000 {
			reg = <0x0 0x4a800000 0x0 0x200000>;
			no-map;
		};

		sbl@4aa00000 {
			reg = <0x0 0x4aa00000 0x0 0x100000>;
			no-map;
		};

		smem@4ab00000 {
			compatible = "qcom,smem";
			reg = <0x0 0x4ab00000 0x0 0x100000>;
			no-map;

			hwlocks = <&tcsr_mutex 3>;
		};

		tz_region: tz@4ac00000 {
			reg = <0x0 0x4ac00000 0x0 0x200000>;
			no-map;
		};
	};

	soc: soc@0 {
		compatible = "simple-bus";
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0 0 0 0xffffffff>;

		usbphy0: phy@5b000 {
			compatible = "qcom,ipq5018-usb-hsphy";
			reg = <0x0005b000 0x120>;

			clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;

			resets = <&gcc GCC_QUSB2_0_PHY_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie1_phy: phy@7e000 {
			compatible = "qcom,ipq5018-uniphy-pcie-phy";
			reg = <0x0007e000 0x800>;

			clocks = <&gcc GCC_PCIE1_PIPE_CLK>;

			resets = <&gcc GCC_PCIE1_PHY_BCR>,
				 <&gcc GCC_PCIE1PHY_PHY_BCR>;

			#clock-cells = <0>;
			#phy-cells = <0>;

			num-lanes = <1>;

			status = "disabled";
		};

		pcie0_phy: phy@86000 {
			compatible = "qcom,ipq5018-uniphy-pcie-phy";
			reg = <0x00086000 0x1000>;

			clocks = <&gcc GCC_PCIE0_PIPE_CLK>;

			resets = <&gcc GCC_PCIE0_PHY_BCR>,
				 <&gcc GCC_PCIE0PHY_PHY_BCR>;

			#clock-cells = <0>;
			#phy-cells = <0>;

			num-lanes = <2>;

			status = "disabled";
		};

		mdio0: mdio@88000 {
			compatible = "qcom,ipq5018-mdio", "qcom,ipq40xx-mdio";
			reg = <0x00088000 0x64>,
			      <0x019475c4 0x4>;
			#address-cells = <1>;
			#size-cells = <0>;

			clocks = <&gcc GCC_MDIO0_AHB_CLK>;
			clock-names = "gcc_mdio_ahb_clk";

			status = "disabled";

			ge_phy: ethernet-phy@7 {
				compatible = "ethernet-phy-id004d.d0c0";
				reg = <7>;

				resets = <&gcc GCC_GEPHY_MISC_ARES>;
			};
		};

		mdio1: mdio@90000 {
			compatible = "qcom,ipq5018-mdio";
			reg = <0x00090000 0x64>;
			#address-cells = <1>;
			#size-cells = <0>;

			clocks = <&gcc GCC_MDIO1_AHB_CLK>;
			clock-names = "gcc_mdio_ahb_clk";

			status = "disabled";
		};

		cmn_pll: clock-controller@9b000 {
			compatible = "qcom,ipq5018-cmn-pll";
			reg = <0x0009b000 0x800>;
			clocks = <&ref_96mhz_clk>,
				 <&gcc GCC_CMN_BLK_AHB_CLK>,
				 <&gcc GCC_CMN_BLK_SYS_CLK>;
			clock-names = "ref",
				      "ahb",
				      "sys";
			#clock-cells = <1>;
			assigned-clocks = <&cmn_pll IPQ5018_CMN_PLL_CLK>;
			assigned-clock-rates-u64 = /bits/ 64 <9600000000>;
		};

		qfprom: qfprom@a0000 {
			compatible = "qcom,ipq5018-qfprom", "qcom,qfprom";
			reg = <0x000a0000 0x1000>;
			#address-cells = <1>;
			#size-cells = <1>;

			tsens_mode: mode@249 {
				reg = <0x249 0x1>;
				bits = <0 3>;
			};

			tsens_base1: base1@249 {
				reg = <0x249 0x2>;
				bits = <3 8>;
			};

			tsens_base2: base2@24a {
				reg = <0x24a 0x2>;
				bits = <3 8>;
			};

			tsens_s0_p1: s0-p1@24b {
				reg = <0x24b 0x2>;
				bits = <2 6>;
			};

			tsens_s0_p2: s0-p2@24c {
				reg = <0x24c 0x1>;
				bits = <1 6>;
			};

			tsens_s1_p1: s1-p1@24c {
				reg = <0x24c 0x2>;
				bits = <7 6>;
			};

			tsens_s1_p2: s1-p2@24d {
				reg = <0x24d 0x2>;
				bits = <5 6>;
			};

			tsens_s2_p1: s2-p1@24e {
				reg = <0x24e 0x2>;
				bits = <3 6>;
			};

			tsens_s2_p2: s2-p2@24f {
				reg = <0x24f 0x1>;
				bits = <1 6>;
			};

			tsens_s3_p1: s3-p1@24f {
				reg = <0x24f 0x2>;
				bits = <7 6>;
			};

			tsens_s3_p2: s3-p2@250 {
				reg = <0x250 0x2>;
				bits = <5 6>;
			};

			tsens_s4_p1: s4-p1@251 {
				reg = <0x251 0x2>;
				bits = <3 6>;
			};

			tsens_s4_p2: s4-p2@254 {
				reg = <0x254 0x1>;
				bits = <0 6>;
			};
		};

		prng: rng@e3000 {
			compatible = "qcom,prng-ee";
			reg = <0x000e3000 0x1000>;
			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "core";
			status = "disabled";
		};

		tsens: thermal-sensor@4a9000 {
			compatible = "qcom,ipq5018-tsens";
			reg = <0x004a9000 0x1000>,
			      <0x004a8000 0x1000>;

			nvmem-cells = <&tsens_mode>,
				      <&tsens_base1>,
				      <&tsens_base2>,
				      <&tsens_s0_p1>,
				      <&tsens_s0_p2>,
				      <&tsens_s1_p1>,
				      <&tsens_s1_p2>,
				      <&tsens_s2_p1>,
				      <&tsens_s2_p2>,
				      <&tsens_s3_p1>,
				      <&tsens_s3_p2>,
				      <&tsens_s4_p1>,
				      <&tsens_s4_p2>;

			nvmem-cell-names = "mode",
					   "base1",
					   "base2",
					   "s0_p1",
					   "s0_p2",
					   "s1_p1",
					   "s1_p2",
					   "s2_p1",
					   "s2_p2",
					   "s3_p1",
					   "s3_p2",
					   "s4_p1",
					   "s4_p2";

			interrupts = <GIC_SPI 184 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "uplow";
			#qcom,sensors = <5>;
			#thermal-sensor-cells = <1>;
		};

		cryptobam: dma-controller@704000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x00704000 0x20000>;
			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <1>;
			qcom,controlled-remotely;
			status = "disabled";
		};

		crypto: crypto@73a000 {
			compatible = "qcom,crypto-v5.1";
			reg = <0x0073a000 0x6000>;
			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
				 <&gcc GCC_CRYPTO_AXI_CLK>,
				 <&gcc GCC_CRYPTO_CLK>;
			clock-names = "iface", "bus", "core";
			dmas = <&cryptobam 2>, <&cryptobam 3>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		tlmm: pinctrl@1000000 {
			compatible = "qcom,ipq5018-tlmm";
			reg = <0x01000000 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&tlmm 0 0 47>;
			interrupt-controller;
			#interrupt-cells = <2>;

			uart1_pins: uart1-state {
				pins = "gpio31", "gpio32", "gpio33", "gpio34";
				function = "blsp1_uart1";
				drive-strength = <8>;
				bias-pull-down;
			};
		};

		gcc: clock-controller@1800000 {
			compatible = "qcom,gcc-ipq5018";
			reg = <0x01800000 0x80000>;
			clocks = <&xo_board_clk>,
				 <&sleep_clk>,
				 <&pcie0_phy>,
				 <&pcie1_phy>,
				 <0>,
				 <&gephy_rx_clk>,
				 <&gephy_tx_clk>,
				 <0>,
				 <0>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		tcsr_mutex: hwlock@1905000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x01905000 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr: syscon@1937000 {
			compatible = "qcom,tcsr-ipq5018", "syscon";
			reg = <0x01937000 0x21000>;
		};

		pwm: pwm@1941010 {
			compatible = "qcom,ipq5018-pwm", "qcom,ipq6018-pwm";
			reg = <0x01941010 0x20>;
			clocks = <&gcc GCC_ADSS_PWM_CLK>;
			assigned-clocks = <&gcc GCC_ADSS_PWM_CLK>;
			assigned-clock-rates = <100000000>;
			#pwm-cells = <2>;
			status = "disabled";
		};

		sdhc_1: mmc@7804000 {
			compatible = "qcom,ipq5018-sdhci", "qcom,sdhci-msm-v5";
			reg = <0x7804000 0x1000>;
			reg-names = "hc";

			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
				 <&gcc GCC_SDCC1_APPS_CLK>,
				 <&xo_board_clk>;
			clock-names = "iface", "core", "xo";
			non-removable;
			status = "disabled";
		};

		blsp_dma: dma-controller@7884000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x07884000 0x1d000>;
			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		blsp1_uart1: serial@78af000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0x078af000 0x200>;
			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp1_uart2: serial@78b0000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0x078b0000 0x200>;
			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
					<&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp1_spi1: spi@78b5000 {
			compatible = "qcom,spi-qup-v2.2.1";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x078b5000 0x600>;
			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		blsp1_i2c3: i2c@78b7000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x078b7000 0x600>;
			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			clock-frequency = <400000>;
			dmas = <&blsp_dma 9>, <&blsp_dma 8>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		qpic_bam: dma@7984000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x07984000 0x1c000>;
			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_QPIC_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
			status = "disabled";
		};

		qpic_nand: qpic-nand@79b0000 {
			compatible = "qcom,ipq5018-snand", "qcom,ipq9574-snand";
			reg = <0x079b0000 0x10000>;
			#address-cells = <1>;
			#size-cells = <0>;
			clocks = <&gcc GCC_QPIC_CLK>,
				 <&gcc GCC_QPIC_AHB_CLK>,
				 <&gcc GCC_QPIC_IO_MACRO_CLK>;
			clock-names = "core", "aon", "iom";

			dmas = <&qpic_bam 0>,
			       <&qpic_bam 1>,
			       <&qpic_bam 2>,
			       <&qpic_bam 3>;
			dma-names = "tx", "rx", "cmd", "status";

			status = "disabled";
		};

		sram@8600000 {
			compatible = "qcom,ipq5018-imem", "syscon", "simple-mfd";
			reg = <0x08600000 0x14000>;
			ranges = <0 0x08600000 0x14000>;

			#address-cells = <1>;
			#size-cells = <1>;
		};

		usb: usb@8af8800 {
			compatible = "qcom,ipq5018-dwc3", "qcom,dwc3";
			reg = <0x08af8800 0x400>;

			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hs_phy_irq";

			clocks = <&gcc GCC_USB0_MASTER_CLK>,
				 <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
				 <&gcc GCC_USB0_SLEEP_CLK>,
				 <&gcc GCC_USB0_MOCK_UTMI_CLK>;
			clock-names = "core",
				      "iface",
				      "sleep",
				      "mock_utmi";

			resets = <&gcc GCC_USB0_BCR>;

			qcom,select-utmi-as-pipe-clk;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			status = "disabled";

			usb_dwc: usb@8a00000 {
				compatible = "snps,dwc3";
				reg = <0x08a00000 0xe000>;
				clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
				clock-names = "ref";
				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
				phy-names = "usb2-phy";
				phys = <&usbphy0>;
				tx-fifo-resize;
				snps,is-utmi-l1-suspend;
				snps,hird-threshold = /bits/ 8 <0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_u3_susphy_quirk;
			};
		};

		intc: interrupt-controller@b000000 {
			compatible = "qcom,msm-qgic2";
			reg = <0x0b000000 0x1000>,  /* GICD */
			      <0x0b002000 0x2000>,  /* GICC */
			      <0x0b001000 0x1000>,  /* GICH */
			      <0x0b004000 0x2000>;  /* GICV */
			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
			interrupt-controller;
			#interrupt-cells = <3>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0x0b00a000 0x1ffa>;

			v2m0: v2m@0 {
				compatible = "arm,gic-v2m-frame";
				reg = <0x00000000 0xff8>;
				msi-controller;
			};

			v2m1: v2m@1000 {
				compatible = "arm,gic-v2m-frame";
				reg = <0x00001000 0xff8>;
				msi-controller;
			};
		};

		watchdog: watchdog@b017000 {
			compatible = "qcom,apss-wdt-ipq5018", "qcom,kpss-wdt";
			reg = <0x0b017000 0x40>;
			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
			clocks = <&sleep_clk>;
		};

		apcs_glb: mailbox@b111000 {
			compatible = "qcom,ipq5018-apcs-apps-global",
				     "qcom,ipq6018-apcs-apps-global";
			reg = <0x0b111000 0x1000>;
			#clock-cells = <1>;
			clocks = <&a53pll>, <&xo_board_clk>, <&gcc GPLL0>;
			clock-names = "pll", "xo", "gpll0";
			#mbox-cells = <1>;
		};

		a53pll: clock@b116000 {
			compatible = "qcom,ipq5018-a53pll";
			reg = <0x0b116000 0x40>;
			#clock-cells = <0>;
			clocks = <&xo_board_clk>;
			clock-names = "xo";
		};

		timer@b120000 {
			compatible = "arm,armv7-timer-mem";
			reg = <0x0b120000 0x1000>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			frame@b120000 {
				reg = <0x0b121000 0x1000>,
				      <0x0b122000 0x1000>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
				frame-number = <0>;
			};

			frame@b123000 {
				reg = <0xb123000 0x1000>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				frame-number = <1>;
				status = "disabled";
			};

			frame@b124000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b124000 0x1000>;
				status = "disabled";
			};

			frame@b125000 {
				reg = <0x0b125000 0x1000>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				frame-number = <3>;
				status = "disabled";
			};

			frame@b126000 {
				reg = <0x0b126000 0x1000>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				frame-number = <4>;
				status = "disabled";
			};

			frame@b127000 {
				reg = <0x0b127000 0x1000>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				frame-number = <5>;
				status = "disabled";
			};

			frame@b128000 {
				reg = <0x0b128000 0x1000>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				frame-number = <6>;
				status = "disabled";
			};
		};

		wifi0: wifi@c000000 {
			compatible = "qcom,ipq5018-wifi";
			reg = <0xc000000 0x1000000>;

			interrupts = <GIC_SPI 288 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 289 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 290 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 291 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 292 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 293 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 294 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 295 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 296 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 297 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 298 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 299 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 300 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 301 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 302 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 303 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 304 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 305 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 306 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 307 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 308 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 309 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 310 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 311 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 312 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 313 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 314 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 315 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 316 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 317 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 318 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 319 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 320 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 321 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 322 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 323 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 324 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 326 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 327 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 329 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 330 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 331 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 332 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 333 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 334 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 335 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 336 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 337 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 338 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 339 IRQ_TYPE_EDGE_RISING>;

			interrupt-names = "misc-pulse1",
					  "misc-latch",
					  "sw-exception",
					  "watchdog",
					  "ce0",
					  "ce1",
					  "ce2",
					  "ce3",
					  "ce4",
					  "ce5",
					  "ce6",
					  "ce7",
					  "ce8",
					  "ce9",
					  "ce10",
					  "ce11",
					  "host2wbm-desc-feed",
					  "host2reo-re-injection",
					  "host2reo-command",
					  "host2rxdma-monitor-ring3",
					  "host2rxdma-monitor-ring2",
					  "host2rxdma-monitor-ring1",
					  "reo2ost-exception",
					  "wbm2host-rx-release",
					  "reo2host-status",
					  "reo2host-destination-ring4",
					  "reo2host-destination-ring3",
					  "reo2host-destination-ring2",
					  "reo2host-destination-ring1",
					  "rxdma2host-monitor-destination-mac3",
					  "rxdma2host-monitor-destination-mac2",
					  "rxdma2host-monitor-destination-mac1",
					  "ppdu-end-interrupts-mac3",
					  "ppdu-end-interrupts-mac2",
					  "ppdu-end-interrupts-mac1",
					  "rxdma2host-monitor-status-ring-mac3",
					  "rxdma2host-monitor-status-ring-mac2",
					  "rxdma2host-monitor-status-ring-mac1",
					  "host2rxdma-host-buf-ring-mac3",
					  "host2rxdma-host-buf-ring-mac2",
					  "host2rxdma-host-buf-ring-mac1",
					  "rxdma2host-destination-ring-mac3",
					  "rxdma2host-destination-ring-mac2",
					  "rxdma2host-destination-ring-mac1",
					  "host2tcl-input-ring4",
					  "host2tcl-input-ring3",
					  "host2tcl-input-ring2",
					  "host2tcl-input-ring1",
					  "wbm2host-tx-completions-ring3",
					  "wbm2host-tx-completions-ring2",
					  "wbm2host-tx-completions-ring1",
					  "tcl2host-status-ring";

			status = "disabled";
		};

		//QCN6102 5G
		wifi1: wifi1@c000000 {
			reg = <0x0b00a040 0x0>;
			compatible = "qcom,qcn6122-wifi";
			interrupts = <GIC_SPI 416 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 417 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 418 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 419 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 420 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 421 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 422 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 423 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 424 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 425 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 426 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 427 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 428 IRQ_TYPE_EDGE_RISING>;
			status = "disabled";
		};

		//QCN6122 5G/6G
		wifi2: wifi2@c000000 {
			reg = <0x0b00a040 0x0>;
			compatible = "qcom,qcn6122-wifi";
			interrupts = <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 449 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 450 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 451 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 452 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 453 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 454 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 455 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 456 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 457 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 458 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 459 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
			status = "disabled";
		};

		q6v5_wcss: remoteproc@cd00000 {
			compatible = "qcom,ipq5018-q6-mpd";
			reg = <0x0cd00000 0x4040>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			clocks = <&gcc GCC_XO_CLK>,
				 <&gcc GCC_SLEEP_CLK_SRC>,
				 <&gcc GCC_SYS_NOC_WCSS_AHB_CLK>;

			interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>,
					      <&wcss_smp2p_in 0 IRQ_TYPE_NONE>,
					      <&wcss_smp2p_in 1 IRQ_TYPE_NONE>,
					      <&wcss_smp2p_in 2 IRQ_TYPE_NONE>,
					      <&wcss_smp2p_in 3 IRQ_TYPE_NONE>;
			interrupt-names = "wdog",
					  "fatal",
					  "ready",
					  "handover",
					  "stop-ack";

			qcom,smem-states = <&wcss_smp2p_out 0>,
					   <&wcss_smp2p_out 1>;
			qcom,smem-state-names = "shutdown",
						"stop";

			status = "disabled";

			glink-edge {
				interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
				label = "rtr";
				qcom,remote-pid = <1>;
				mboxes = <&apcs_glb 8>;

				qrtr_requests {
					qcom,glink-channels = "IPCRTR";
				};
			};
		};

		wcss: smp2p-wcss {
			compatible = "qcom,smp2p";
			qcom,smem = <435>, <428>;

			interrupt-parent = <&intc>;
			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;

			mboxes = <&apcs_glb 9>;

			qcom,local-pid = <0>;
			qcom,remote-pid = <1>;

			wcss_smp2p_out: master-kernel {
				qcom,entry-name = "master-kernel";
				qcom,smp2p-feature-ssr-ack;
				#qcom,smem-state-cells = <1>;
			};

			wcss_smp2p_in: slave-kernel {
				qcom,entry-name = "slave-kernel";
				interrupt-controller;
				#interrupt-cells = <2>;
			};
		};

		pcie1: pcie@80000000 {
			compatible = "qcom,pcie-ipq5018";
			reg = <0x80000000 0xf1d>,
			      <0x80000f20 0xa8>,
			      <0x80001000 0x1000>,
			      <0x00078000 0x3000>,
			      <0x80100000 0x1000>,
			      <0x0007b000 0x1000>;
			reg-names = "dbi",
				    "elbi",
				    "atu",
				    "parf",
				    "config",
				    "mhi";
			device_type = "pci";
			linux,pci-domain = <1>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;
			#address-cells = <3>;
			#size-cells = <2>;

			/* The controller supports Gen3, but the connected PHY is Gen2-capable */
			max-link-speed = <2>;

			phys = <&pcie1_phy>;
			phy-names ="pciephy";

			ranges = <0x01000000 0 0x00000000 0x80200000 0 0x00100000>,
				 <0x02000000 0 0x80300000 0x80300000 0 0x10000000>;

			msi-map = <0x0 &v2m0 0x0 0xff8>;

			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0",
					  "msi1",
					  "msi2",
					  "msi3",
					  "msi4",
					  "msi5",
					  "msi6",
					  "msi7",
					  "global";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 142 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 143 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 144 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 145 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_SYS_NOC_PCIE1_AXI_CLK>,
				 <&gcc GCC_PCIE1_AXI_M_CLK>,
				 <&gcc GCC_PCIE1_AXI_S_CLK>,
				 <&gcc GCC_PCIE1_AHB_CLK>,
				 <&gcc GCC_PCIE1_AUX_CLK>,
				 <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>;
			clock-names = "iface",
				      "axi_m",
				      "axi_s",
				      "ahb",
				      "aux",
				      "axi_bridge";

			resets = <&gcc GCC_PCIE1_PIPE_ARES>,
				 <&gcc GCC_PCIE1_SLEEP_ARES>,
				 <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
				 <&gcc GCC_PCIE1_AXI_MASTER_ARES>,
				 <&gcc GCC_PCIE1_AXI_SLAVE_ARES>,
				 <&gcc GCC_PCIE1_AHB_ARES>,
				 <&gcc GCC_PCIE1_AXI_MASTER_STICKY_ARES>,
				 <&gcc GCC_PCIE1_AXI_SLAVE_STICKY_ARES>;
			reset-names = "pipe",
				      "sleep",
				      "sticky",
				      "axi_m",
				      "axi_s",
				      "ahb",
				      "axi_m_sticky",
				      "axi_s_sticky";

			status = "disabled";

			pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};

		pcie0: pcie@a0000000 {
			compatible = "qcom,pcie-ipq5018";
			reg = <0xa0000000 0xf1d>,
			      <0xa0000f20 0xa8>,
			      <0xa0001000 0x1000>,
			      <0x00080000 0x3000>,
			      <0xa0100000 0x1000>,
			      <0x00083000 0x1000>;
			reg-names = "dbi",
				    "elbi",
				    "atu",
				    "parf",
				    "config",
				    "mhi";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;
			#address-cells = <3>;
			#size-cells = <2>;

			/* The controller supports Gen3, but the connected PHY is Gen2-capable */
			max-link-speed = <2>;

			phys = <&pcie0_phy>;
			phy-names ="pciephy";

			ranges = <0x01000000 0 0x00000000 0xa0200000 0 0x00100000>,
				 <0x02000000 0 0xa0300000 0xa0300000 0 0x10000000>;

			msi-map = <0x0 &v2m0 0x0 0xff8>;

			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0",
					  "msi1",
					  "msi2",
					  "msi3",
					  "msi4",
					  "msi5",
					  "msi6",
					  "msi7",
					  "global";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 75 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 78 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 79 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 83 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
				 <&gcc GCC_PCIE0_AXI_M_CLK>,
				 <&gcc GCC_PCIE0_AXI_S_CLK>,
				 <&gcc GCC_PCIE0_AHB_CLK>,
				 <&gcc GCC_PCIE0_AUX_CLK>,
				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>;
			clock-names = "iface",
				      "axi_m",
				      "axi_s",
				      "ahb",
				      "aux",
				      "axi_bridge";

			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
				 <&gcc GCC_PCIE0_SLEEP_ARES>,
				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
				 <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
				 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
				 <&gcc GCC_PCIE0_AHB_ARES>,
				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
				 <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
			reset-names = "pipe",
				      "sleep",
				      "sticky",
				      "axi_m",
				      "axi_s",
				      "ahb",
				      "axi_m_sticky",
				      "axi_s_sticky";

			status = "disabled";

			pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};
	};

	thermal-zones {
		cpu-thermal {
			thermal-sensors = <&tsens 2>;

			trips {
				cpu-critical {
					temperature = <120000>;
					hysteresis = <1000>;
					type = "critical";
				};

				cpu_alert: cpu-passive {
					temperature = <100000>;
					hysteresis = <1000>;
					type = "passive";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu_alert>;
					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		gephy-thermal {
			thermal-sensors = <&tsens 4>;

			trips {
				gephy-critical {
					temperature = <120000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		top-glue-thermal {
			thermal-sensors = <&tsens 3>;

			trips {
				top-glue-critical {
					temperature = <120000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		ubi32-thermal {
			thermal-sensors = <&tsens 1>;

			trips {
				ubi32-critical {
					temperature = <120000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
	};
};