Skip to content

Instantly share code, notes, and snippets.

@kkedf

kkedf/amlogic s805 image test log 02

Created November 1, 2022 03:02
Show Gist options
  • Save kkedf/2f4f0348f28b248fbe586753e7ea01ad to your computer and use it in GitHub Desktop.
Save kkedf/2f4f0348f28b248fbe586753e7ea01ad to your computer and use it in GitHub Desktop.
Download ZIP
Raw
amlogic s805 image test log 02
LibreELEC-m201d.arm-9.2.8.6.img.gz
no hdmi boot ok uart ok
QA5:A;SVN:B72;POC:3FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 24849
BT : 13:32:50 Jan 11 2016
PMU:NONE
##### VDDEE voltage = 0x044c
CPU clock is 792MHz
DDR mode: 32 bit mode
DDR size: 1GB (auto)
DDR check: Pass!
DDR clock: 636MHz with 2T mode
DDR pll bypass: Disabled
DDR init use : 14817 us
HHH
ucl decompress...pass
0x12345678
Boot from internal device 1st NAND
TE : 214628
System Started
U-boot(m8b_m201_v1@) (Jan 11 2016 - 13:32:30)
clr h-ram
DRAM: 1 GiB
relocation Offset is: 2fecc000
show partition table:
part: 0, name : logo, size : 2000000
part: 1, name : recovery, size : 2000000
part: 2, name : misc, size : 2000000
part: 3, name : reserved, size : 2000000
part: 4, name : boot, size : 2000000
part: 5, name : system, size : 40000000
part: 6, name : cache, size : 20000000
part: 7, name : data, size : end
aml_card_type=0x100
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
power init
out reg=c110804c,value=dfffffff
set GPIOAO_12 up!!!!!!!
IR init done!
register usb cfg[0][1] = 3ff7396c
register usb cfg[2][0] = 3ff76480
NAND: NAND BOOT: boot_device_flag 1
Nand PHY driver Version: 1.01.001.0003 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 0
NAND device id: 2c 44 44 4b a9 0 0 0
detect NAND device: D revision NAND 4GiB MT29F32G08CBADA
AML_NAND_NEW_OOB : new oob
bus_cycle=5, bus_timing=7,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0
NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 7
i=0,register --- nand_key
NAND CKECK : arg nenv: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 72
nfboot : offset: 0x000000000000 -0x000000800000 : partitons 0 : single_chip single_plane
nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
nfcode : offset: 0x00002b000000 -0x000052800000 : partitons 6 : single_chip multi_plane
nfdata : offset: 0x00007d800000 -0x000082800000 : partitons 1 : single_chip multi_plane
bad block count = 0
bad block count = 0
bad block count = 0
bad block count = 0
amlnf_logic_init: START
aml_nftl_start:117,size_in_blk=145,tmp_block=128,part->free_block_num=17
aml_nftl_start:117,size_in_blk=330,tmp_block=296,part->free_block_num=34
amlnf_logic_init: COMPLETE
get_boot_device_flag: init_ret 0
get_boot_device_flag NAND BOOT:
NAND BOOT,nand_env_relocate_spec : env_relocate_spec 49
uboot env amlnf_env_read : ####
set_storage_device_flag: store 1
aml_dt: <NULL>
aml_dt: m8b_m201_1g
Multi dtb tool version: v2 .
Multi dtb detected, support 2 dtbs.
aml_dt soc: m8b platform: m201 variant: 1g
dtb 0 soc: m8b plat: m201 vari: 1g
dtb 1 soc: m8b plat: m201 vari: 512m
Find match dtb: 0
vpu clk_level in dts: 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
hdmi tx power init
cvbs performance type = 1, table = 0
vdac open.1 = 0x1, 0x0
mode is: 4
viu chan = 1
config HPLL
config HPLL done
reboot_mode=charging
ir init
<ir> release
<ir> release
<ir> release
<ir> release
efuse version is not selected.
Hit Enter key to stop autoboot -- : 0
exit abortboot: 0
[mmc_init] SDIO Port B:0, if_type=7, initialized OK!
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 7948206080
Boot Part Size: 0
Bus Width: 4-bit
reading kernel.img
8175616 bytes read
usage: fatload <interface> <dev[:part]> <addr> <filename> [bytes]
store - STORE sub-system
Usage:
store store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store scrub off|partition size
scrub the area from offset and size
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.108
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 4315209 Bytes = 4.1 MiB
Load Address: 00208000
Entry Point: 00208000
Verifying Checksum ... OK
Ramdisk start addr = 0x1241e800, len = 0x3a8800
Flat device tree start addr = 0x127c7000, len = 0x4d44 magic=0xedfe0dd0
Uncompressing Kernel Image ... OK
uboot time: 3953758 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x53b1001
Loading Ramdisk to 05008000, end 053b0800 ... OK
Loading Device Tree to 05000000, end 05007d43 ... OK
Starting kernel ...
[ 0.000000@0] Global timer: MESON TIMER-F (c084b200) initialized
[ 41.681863@0] Restarting system.
[ 41.681952@0] Restarting Linux version 3.10.108 (dtech@LibreBuilder) (gcc version 8.3.0 (GCC) ) #1 SMP PREEMPT Fri Aug 26 01:55:43 CEST 2022
[ 41.681952@0]
QA5:A;SVN:B72;POC:3FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 24850
BT : 13:32:50 Jan 11 2016
PMU:NONE
##### VDDEE voltage = 0x044c
CPU clock is 792MHz
DDR mode: 32 bit mode
DDR size: 1GB (auto)
DDR check: Pass!
DDR clock: 636MHz with 2T mode
DDR pll bypass: Disabled
DDR init use : 14825 us
HHH
ucl decompress...pass
0x12345678
Boot from internal device 1st NAND
TE : 214664
System Started
U-boot(m8b_m201_v1@) (Jan 11 2016 - 13:32:30)
clr h-ram
DRAM: 1 GiB
relocation Offset is: 2fecc000
show partition table:
part: 0, name : logo, size : 2000000
part: 1, name : recovery, size : 2000000
part: 2, name : misc, size : 2000000
part: 3, name : reserved, size : 2000000
part: 4, name : boot, size : 2000000
part: 5, name : system, size : 40000000
part: 6, name : cache, size : 20000000
part: 7, name : data, size : end
aml_card_type=0x100
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
power init
out reg=c110804c,value=dfffffff
set GPIOAO_12 up!!!!!!!
IR init done!
register usb cfg[0][1] = 3ff7396c
register usb cfg[2][0] = 3ff76480
NAND: NAND BOOT: boot_device_flag 1
Nand PHY driver Version: 1.01.001.0003 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 0
NAND device id: 2c 44 44 4b a9 0 0 0
detect NAND device: D revision NAND 4GiB MT29F32G08CBADA
AML_NAND_NEW_OOB : new oob
bus_cycle=5, bus_timing=7,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0
NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 7
i=0,register --- nand_key
NAND CKECK : arg nenv: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 72
nfboot : offset: 0x000000000000 -0x000000800000 : partitons 0 : single_chip single_plane
nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
nfcode : offset: 0x00002b000000 -0x000052800000 : partitons 6 : single_chip multi_plane
nfdata : offset: 0x00007d800000 -0x000082800000 : partitons 1 : single_chip multi_plane
bad block count = 0
bad block count = 0
bad block count = 0
bad block count = 0
amlnf_logic_init: START
aml_nftl_start:117,size_in_blk=145,tmp_block=128,part->free_block_num=17
aml_nftl_start:117,size_in_blk=330,tmp_block=296,part->free_block_num=34
amlnf_logic_init: COMPLETE
get_boot_device_flag: init_ret 0
get_boot_device_flag NAND BOOT:
NAND BOOT,nand_env_relocate_spec : env_relocate_spec 49
uboot env amlnf_env_read : ####
set_storage_device_flag: store 1
aml_dt: <NULL>
aml_dt: m8b_m201_1g
Multi dtb tool version: v2 .
Multi dtb detected, support 2 dtbs.
aml_dt soc: m8b platform: m201 variant: 1g
dtb 0 soc: m8b plat: m201 vari: 1g
dtb 1 soc: m8b plat: m201 vari: 512m
Find match dtb: 0
vpu clk_level in dts: 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
hdmi tx power init
cvbs performance type = 1, table = 0
vdac open.1 = 0x1, 0x0
mode is: 4
viu chan = 1
config HPLL
config HPLL done
reboot_mode=normal
ir init
<ir> release
<ir> release
<ir> release
<ir> release
efuse version is not selected.
Hit Enter key to stop autoboot -- : 0
exit abortboot: 0
[mmc_init] SDIO Port B:0, if_type=7, initialized OK!
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 7948206080
Boot Part Size: 0
Bus Width: 4-bit
reading kernel.img
8175616 bytes read
usage: fatload <interface> <dev[:part]> <addr> <filename> [bytes]
store - STORE sub-system
Usage:
store store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store scrub off|partition size
scrub the area from offset and size
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.108
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 4315209 Bytes = 4.1 MiB
Load Address: 00208000
Entry Point: 00208000
Verifying Checksum ... OK
Ramdisk start addr = 0x1241e800, len = 0x3a8800
Flat device tree start addr = 0x127c7000, len = 0x4d44 magic=0xedfe0dd0
Uncompressing Kernel Image ... OK
uboot time: 3799386 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x53b1001
Loading Ramdisk to 05008000, end 053b0800 ... OK
Loading Device Tree to 05000000, end 05007d43 ... OK
Starting kernel ...
[ 0.000000@0] Global timer: MESON TIMER-F (c084b200) initialized
LibreELEC:~ #
LibreELEC:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:01:23:CD:EE:AF
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:680 (680.0 B)
Interrupt:40
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan0 Link encap:Ethernet HWaddr 9C:44:3D:20:9D:6C
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:10 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
LibreELEC:~ # kodi-
kodi-ps3remote kodi-remote kodi-send
LibreELEC:~ # kodi-
kodi-ps3remote kodi-remote kodi-send
LibreELEC:~ # top
top - 00:16:13 up 15 min, 0 users, load average: 0.56, 0.55, 0.40
top - 00:16:16 up 15 min, 0 users, load average: 0.56, 0.55, 0.40
top - 00:16:19 up 15 min, 0 users, load average: 0.52, 0.54, 0.40
%Cpu(s): 17.0 us, 7.0 sy, 3.2 ni, 72.8 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st
%Cpu(s): 15.6 us, 2.0 sy, 0.2 ni, 81.8 id, 0.2 wa, 0.2 hi, 0.0 si, 0.0 st
2145 root 20 0 397332 41476 20892 S 45.4 11.8 5:53.48 kodi.bin
2145 root 20 0 397332 41476 20892 S 31.4 11.8 5:54.45 kodi.bin
2243 root 20 0 2816 1004 788 R 1.6 0.3 0:00.22 top
2239 root 20 0 0 0 0 S 1.3 0.0 0:03.91 kworker/1+
1 root 20 0 24448 3788 2944 S 0.6 1.1 0:06.37 systemd
1035 root 20 0 0 0 0 S 0.6 0.0 0:04.75 kthread_h+
1040 root 20 0 0 0 0 S 0.6 0.0 0:03.34 kworker/0+
905 root 20 0 0 0 0 S 0.3 0.0 0:04.32 kthread_di
2127 root 20 0 0 0 0 S 0.3 0.0 0:03.38 RTW_CMD_T+
2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd
3 root 20 0 0 0 0 S 0.0 0.0 0:00.75 ksoftirqd+
5 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/0+
6 root 20 0 0 0 0 S 0.0 0.0 0:00.08 kworker/u+
7 root rt 0 0 0 0 S 0.0 0.0 0:00.00 migration+
8 root 20 0 0 0 0 S 0.0 0.0 0:00.59 rcu_preem+
9 root 20 0 0 0 0 S 0.0 0.0 0:00.00 rcu_bh
10 root 20 0 0 0 0 S 0.0 0.0 0:00.00 rcu_sched
11 root rt 0 0 0 0 S 0.0 0.0 0:00.00 migration+
LibreELEC:~ #
@kkedf
Copy link
Author

kkedf commented Nov 1, 2022

dmesg
[ 0.000000@0] Booting Linux on physical CPU 0x200
[ 0.000000@0] Linux version 3.10.108 (dtech@LibreBuilder) (gcc version 8.3.0 (GCC) ) #1 SMP PREEMPT Fri Aug 26 01:55:43 CEST 2022
[ 0.000000@0] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d
[ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000@0] Machine: Amlogic Meson8B, model: AMLOGIC
[ 0.000000@0] physical memory start address is 0x200000
[ 0.000000@0] reserved_end is b9fffff
[ 0.000000@0]
[ 0.000000@0] Total memory is 510 MiB
[ 0.000000@0] Reserved low memory from 0x06000000 to 0x0b9fffff, size: 90 MiB
[ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB)
[ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB)
[ 0.000000@0] deinterlace0(high) : 0x1e800000 - 0x20000000 ( 24 MiB)
[ 0.000000@0] mesonstream0(high) : 0x1e000000 - 0x1e800000 ( 8 MiB)
[ 0.000000@0] vdec0(low) : 0x07a00000 - 0x0ba00000 ( 64 MiB)
[ 0.000000@0] ppmgr0(high) : 0x1d000000 - 0x1e000000 ( 16 MiB)
[ 0.000000@0] get storage device: storage 1
[ 0.000000@0] value=1
[ 0.000000@0] get_storage_device : get storage device: storage 1
[ 0.000000@0] get_storage_device : value=1
[ 0.000000@0] [get_storage_device] storage_flag=1
[ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=1
[ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000@0] On node 0 totalpages: 91648
[ 0.000000@0] free_area_init_node: node 0, pgdat c0886680, node_mem_map c0abb000
[ 0.000000@0] Normal zone: 924 pages used for memmap
[ 0.000000@0] Normal zone: 0 pages reserved
[ 0.000000@0] Normal zone: 91648 pages, LIFO batch:31
[ 0.000000@0] Meson chip version = RevA (1B:A - 0:B72)
[ 0.000000@0] PERCPU: Embedded 7 pages/cpu @c0e62000 s7488 r8192 d12992 u32768
[ 0.000000@0] pcpu-alloc: s7488 r8192 d12992 u32768 alloc=8*4096
[ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 90724
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend loglevel=4 storage=1 cvbsdrv=0 vdaccfg=0xa000 logo=osd1,loaded,0x7900000,576cvbs,full hdmimode=720p cvbsmode=576cvbs androidboot.firstboot=0 hdmitx= bootfromsd console=ttyS0,115200n8 no_console_suspend console=tty0 consoleblank=0 systemd.show_status=auto
[ 0.000000@0] cvbs performance line = 0
[ 0.000000@0] cvbs trimming line = 0xa000
[ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
[ 0.000000@0] osd1:1
[ 0.000000@0] loaded:268435459
[ 0.000000@0] logo has been loaded
[ 0.000000@0] 576cvbs:8
[ 0.000000@0] full:2
[ 0.000000@0] kernel get hdmimode form uboot is 720p
[ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
[ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 64MB 16MB 278MB = 358MB total
[ 0.000000@0] Memory: 347536k/347536k available, 19056k reserved, 0K highmem
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000@0] vmalloc : 0xdd000000 - 0xff000000 ( 544 MB)
[ 0.000000@0] lowmem : 0xc0000000 - 0xdce00000 ( 462 MB)
[ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000@0] .text : 0xc0008000 - 0xc07ff934 (8159 kB)
[ 0.000000@0] .init : 0xc0800000 - 0xc082fd40 ( 192 kB)
[ 0.000000@0] .data : 0xc0830000 - 0xc08874d8 ( 350 kB)
[ 0.000000@0] .bss : 0xc08874d8 - 0xc0ab6ab0 (2238 kB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] NR_IRQS:256
[ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000@0] Global timer: MESON TIMER-F (c084b200) initialized
[ 0.000000@0] Switching to timer-based delay loop
[ 0.000000@0] Console: colour dummy device 80x30
[ 0.000000@0] console [tty0] enabled
[ 0.000000@0] meson_serial_console_setup
[ 0.000000@0] console [ttyS0] enabled
[ 0.001280@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.001303@0] pid_max: default: 32768 minimum: 301
[ 0.001565@0] Mount-cache hash table entries: 512
[ 0.007722@0] CPU: Testing write buffer coherency: ok
[ 0.008237@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[ 0.008354@0] Setting up static identity map for 0xc05c6420 - 0xc05c6478
[ 0.008515@0] L310 cache controller enabled
[ 0.008540@0] l2x0: 8 ways, 2048 sets, CACHE_ID 0x4100a0c9, Cache size: 524288 B
[ 0.008551@0] AUX_CTRL 0x7ec60001, PERFETCH_CTRL 0x75000007, POWER_CTRL 0x00000000
[ 0.008561@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
[ 0.060398@1] CPU1: Booted secondary processor
[ 0.060423@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[ 0.080377@2] CPU2: Booted secondary processor
[ 0.080401@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[ 0.100375@3] CPU3: Booted secondary processor
[ 0.100392@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[ 0.100497@0] Brought up 4 CPUs
[ 0.100540@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
[ 0.100549@0] CPU: All CPU(s) started in SVC mode.
[ 0.101364@0] devtmpfs: initialized
[ 0.110974@0] clkrate [ xtal ] : 24000000
[ 0.110990@0] clkrate [ pll_sys ] : 792000000
[ 0.111001@0] clkrate [ pll_fixed ] : 2550000000
[ 0.111012@0] clkrate [ pll_vid ] : 648000000
[ 0.111021@0] clkrate [ pll_ddr ] : 0
[ 0.111031@0] clkrate [ a9_clk ] : 792000000
[ 0.111042@0] clkrate [ clk81 ] : 159375000
[ 0.112338@1] pinctrl core: initialized pinctrl subsystem
[ 0.113029@1] regulator-dummy: no parameters
[ 0.113427@1] NET: Registered protocol family 16
[ 0.118049@1] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.121147@1] VPU driver version: v02
[ 0.121163@1] load vpu_clk in dts: 182150000Hz(3)
[ 0.121298@1] vpu_probe OK
[ 0.129158@1] amlogic_gpio gpio: Probed amlogic GPIO driver
[ 0.129805@1] register lm device lm-root
[ 0.129974@1] register lm device lm1
[ 0.130142@1] register lm device lm0
[ 0.130607@1] Init pinux probe!
[ 0.131464@1] pinmux-m8b pinmux: Probed amlogic pinctrl driver
[ 0.131846@1] -------early_init_dt_init:115----------
[ 0.131858@1] tv_init_module
[ 0.131876@1] major number 254 for disp
[ 0.131885@1] vout_register_server
[ 0.131893@1] register tv module server ok
[ 0.132073@1] aml_i2c version: 20140813
[ 0.132292@1] aml_pmu_init, 458
[ 0.132427@1] call aml_dvfs_init in
[ 0.132496@1] [DVFS]aml_dvfs_probe, child name:vcck_dvfs
[ 0.132511@1] [DVFS]dvfs table of vcck_dvfs is:
[ 0.132522@1] [DVFS] freq, min_uV, max_uV
[ 0.132532@1] [DVFS] 96000, 860000, 860000
[ 0.132542@1] [DVFS] 192000, 860000, 860000
[ 0.132551@1] [DVFS] 312000, 860000, 860000
[ 0.132561@1] [DVFS] 408000, 860000, 860000
[ 0.132571@1] [DVFS] 504000, 860000, 860000
[ 0.132580@1] [DVFS] 600000, 860000, 860000
[ 0.132590@1] [DVFS] 720000, 860000, 860000
[ 0.132600@1] [DVFS] 816000, 900000, 900000
[ 0.132609@1] [DVFS] 1008000, 920000, 920000
[ 0.132619@1] [DVFS] 1200000, 970000, 970000
[ 0.132629@1] [DVFS] 1320000, 1100000, 1100000
[ 0.132638@1] [DVFS] 1488000, 1100000, 1100000
[ 0.132648@1] [DVFS] 1536000, 1140000, 1140000
[ 0.132663@1] [DVFS]aml_dvfs_register_driver, driver aml-dumy-dvfs regist success, mask:1, source id:1
[ 0.132944@1] hdmitx: system: amhdmitx_init
[ 0.132955@1] hdmitx: system: Ver: 2014May6
[ 0.133048@1] hdmitx: system: amhdmitx_probe
[ 0.133800@1] hdmitx: system: gate/pwr cmd: 7
[ 0.133813@1] hdmitx: system: gate/pwr cmd: 1
[ 0.133825@1] hdmitx: system: hw init
[ 0.134387@0] hdmitx: system: reset intr mask
[ 0.226139@1] bio: create slab at 0
[ 0.227661@2] SCSI subsystem initialized
[ 0.228391@2] usbcore: registered new interface driver usbfs
[ 0.228569@2] usbcore: registered new interface driver hub
[ 0.228780@2] usbcore: registered new device driver usb
[ 0.229156@2] pps_core: LinuxPPS API ver. 1 registered
[ 0.229168@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [email protected]
[ 0.229297@2] PTP clock support registered
[ 0.230299@2] mode is 8,sync_duration_den=1,sync_duration_num=50
[ 0.230316@2] request vpu clk holdings: venci 106250000Hz
[ 0.230326@2] TV mode 576cvbs selected.
[ 0.230342@2] tvoutc_setmode[505]
[ 0.230351@2] cvbs performance type = 1, table = 0
[ 0.230360@2] tvoutc_setmode[516] mode is 8
[ 0.230370@2] mode is: 8
[ 0.230379@2] VPU_VIU_VENC_MUX_CTRL: 0x5
[ 0.230386@2] viu chan = 1
[ 0.230394@2] VPU_VIU_VENC_MUX_CTRL: 0x5
[ 0.230401@2] config HPLL
[ 0.230411@2] set_hpll_clk_out[206] clk = 1296
[ 0.250438@2] config HPLL done
[ 1.260446@2] vdac open.1 = 0x1, 0x0
[ 1.260460@2] vinfo mode is: 576cvbs
[ 1.265522@2] call aml_pmu_probe_init in
[ 1.266407@2] Advanced Linux Sound Architecture Driver Initialized.
[ 1.268319@2] Switching to clocksource Timer-E
[ 1.268643@2] FS-Cache: Loaded
[ 1.289125@2] NET: Registered protocol family 2
[ 1.290041@2] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.290146@2] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.290226@2] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.290289@2] TCP: reno registered
[ 1.290308@2] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.290338@2] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.290646@2] NET: Registered protocol family 1
[ 1.290960@2] RPC: Registered named UNIX socket transport module.
[ 1.290975@2] RPC: Registered udp transport module.
[ 1.290984@2] RPC: Registered tcp transport module.
[ 1.290993@2] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.291089@2] wifi_dev_probe
[ 1.291103@2] wifi_dt : interrupt_pin=GPIOX_21
[ 1.291121@2] wifi_dt : irq_num=null
[ 1.291131@2] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
[ 1.291141@2] wifi_dt : power_on_pin=GPIOAO_6
[ 1.291154@2] wifi_dt : power_on_pin2=GPIOX_11
[ 1.291172@2] interrupt_pin=118, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=107
[ 1.291493@2] Unpacking initramfs...
[ 1.311836@2] Freeing initrd memory: 3744K
[ 1.327251@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.329376@2] NFS: Registering the id_resolver key type
[ 1.329440@2] Key type id_resolver registered
[ 1.329450@2] Key type id_legacy registered
[ 1.331116@2] msgmni has been set to 686
[ 1.332893@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.332911@2] io scheduler noop registered (default)
[ 1.332922@2] io scheduler deadline registered
[ 1.333424@2] io scheduler cfq registered
[ 1.333452@2] io scheduler fiops registered
[ 1.343095@2] loop: module loaded
[ 1.345411@2] tun: Universal TUN/TAP device driver, 1.6
[ 1.345425@2] tun: (C) 1999-2004 Max Krasnyansky [email protected]
[ 1.346123@2] ethernet base addr is fe0c0000
[ 1.346156@2] key device don't create,extenal_api_key_set_version:2052
[ 1.346166@2] ret = -22
[ 1.346166@2] print_buff=
[ 1.346181@2] key device don't create,extenal_api_key_set_version:2052
[ 1.346190@2] ret = -22
[ 1.346190@2] print_buff=
[ 1.346216@2] efuse version is not selected.
[ 1.346225@2] ID is not found
[ 1.346286@2] DWMAC100
[ 1.346298@2] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 1.346306@2] Normal descriptors
[ 1.346314@2] Ring mode enabled
[ 1.346322@2] DMA HW capability register supported
[ 1.346332@2] RX Checksum Offload Engine supported (type 2)
[ 1.346340@2] TX Checksum insertion supported
[ 1.346348@2] Wake-Up On Lan supported
[ 1.346396@2] Enable RX Mitigation via HW Watchdog Timer
[ 1.361750@2] libphy: stmmac: probed
[ 1.361770@2] eth%d: PHY ID 02430c54 at 0 IRQ POLL (stmmac-0:00) active
[ 1.362938@2] PPP generic driver version 2.4.2
[ 1.363355@2] NET: Registered protocol family 24
[ 1.363570@2] usbcore: registered new interface driver smsc95xx
[ 1.363769@2] usbcore: registered new interface driver qf9700
[ 1.363932@2] usbcore: registered new interface driver sr9600
[ 1.364470@2] usbcore: registered new interface driver usb-storage
[ 1.364834@2] usbcore: registered new interface driver usbserial
[ 1.364998@2] usbcore: registered new interface driver usbserial_generic
[ 1.365151@2] usbserial: USB Serial support registered for generic
[ 1.365307@2] usbcore: registered new interface driver pl2303
[ 1.365458@2] usbserial: USB Serial support registered for pl2303
[ 1.365779@2] mousedev: PS/2 mouse device common for all mice
[ 1.366058@2] i2c /dev entries driver
[ 1.366734@2] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.371125@2] usbcore: registered new interface driver usbhid
[ 1.371139@2] usbhid: USB HID core driver
[ 1.371844@2] ashmem: initialized
[ 1.372171@2] logger: created 256K log 'log_main'
[ 1.372481@2] logger: created 256K log 'log_events'
[ 1.372784@2] logger: created 256K log 'log_radio'
[ 1.373097@2] logger: created 256K log 'log_system'
[ 1.373244@2] vout_init_module
[ 1.373321@2] start init vout module
[ 1.373485@2] create vout attribute ok
[ 1.373735@2] ge2d_init
[ 1.373755@2] ge2d_dev major:245
[ 1.374186@2] ge2d start monitor
[ 1.374264@2] osd_init
[ 1.374274@1] ge2d workqueue monitor start
[ 1.374344@2] osd_probe, vinfo:c06010a4
[ 1.374776@2] Frame buffer memory assigned at phy:0x06100000, vir:0xde000000, size=24576K
[ 1.374789@2] osd_probe, mydef_var:c08711b8, vinfo:c06010a4
[ 1.374800@2] init fbdev bpp is :32
[ 1.374809@2] ---------------clear framebuffer0 memory
[ 1.435291@0] Console: switching to colour frame buffer device 240x67
[ 1.495009@0] Frame buffer memory assigned at phy:0x07900000, vir:0xdd600000, size=1024K
[ 1.495023@0] osd_probe, mydef_var:c08711b8, vinfo:c06010a4
[ 1.495032@0] don't find to display_size_default from mesonfb-dts
[ 1.495041@0] init fbdev bpp is :16
[ 1.514890@0] osd probe ok
[ 1.515203@1] enter aml_sysled_init
[ 1.516282@1] DI: di_init
[ 1.516339@1] DI: di_probe
[ 1.517194@2] aml_wdt_driver_init,306
[ 1.517207@2] ** disable watchdog
[ 1.517547@2] keys===========================================
[ 1.517563@2] keys_devno=f200000
[ 1.518010@2] securitykey: device aml_keys created
[ 1.518040@2] amlkeys=0
[ 1.518219@2] platform_driver_register--aml_keys_driver--------------------
[ 1.518847@1] set uart_ao pinmux use pinctrl subsystem
[ 1.518860@1] P_AO_RTI_PIN_MUX_REG:78001861
[ 1.518891@1] start uart_ao_ttyS0:(irq = 122)
[ 1.518901@1] register uart_ao ok
[ 1.519373@1] set uart_b pinmux use pinctrl subsystem
[ 1.519385@1] P_AO_RTI_PIN_MUX_REG:78001861
[ 1.519415@1] start uart_b_ttyS2:(irq = 107)
[ 1.519424@1] register uart_b ok
[ 1.519869@1] start uart_d_ttyS4:(irq = 126)
[ 1.519881@1] register uart_d ok
[ 1.520155@1] dwc_otg: version 3.10a 12-MAY-2014
[ 1.520200@1] dwc_otg_driver_probe NOT match
[ 1.520253@1] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
[ 1.520275@1] USB (1) use clock source: XTAL input
[ 1.541419@1] Core Release: 3.10a
[ 1.541442@1] Setting default values for core params
[ 1.541459@1] curmode: 1, host_only: 1
[ 1.561702@1] Using Buffer DMA mode
[ 1.561719@1] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 1.561729@1] Working on port type = HOST
[ 1.561784@1] dwc_otg lm1: DWC OTG Controller
[ 1.561820@1] dwc_otg lm1: new USB bus registered, assigned bus number 1
[ 1.561862@1] dwc_otg lm1: irq 63, io mem 0x00000000
[ 1.561873@1] -------hcd->flags.d32 = 0
[ 1.561903@1] Init: Port Power? op_state=1
[ 1.561911@1] Init1: Power Port (0)
[ 1.562054@1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.562070@1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.562083@1] usb usb1: Product: DWC OTG Controller
[ 1.562096@1] usb usb1: Manufacturer: Linux 3.10.108 dwc_otg_hcd
[ 1.562108@1] usb usb1: SerialNumber: lm1
[ 1.562926@1] hub 1-0:1.0: USB hub found
[ 1.562957@1] hub 1-0:1.0: 1 port detected
[ 1.563271@1] usb0: type: 1, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
[ 1.563294@1] USB (0) use clock source: XTAL input
[ 1.584384@1] Core Release: 3.10a
[ 1.584402@1] Setting default values for core params
[ 1.584417@1] curmode: 1, host_only: 1
[ 1.604632@1] Using Buffer DMA mode
[ 1.604649@1] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 1.604658@1] Working on port type = HOST
[ 1.604713@1] dwc_otg lm0: DWC OTG Controller
[ 1.604747@1] dwc_otg lm0: new USB bus registered, assigned bus number 2
[ 1.604788@1] dwc_otg lm0: irq 62, io mem 0x00000000
[ 1.604798@1] -------hcd->flags.d32 = 0
[ 1.604827@1] Init: Port Power? op_state=1
[ 1.604835@1] Init1: Power Port (0)
[ 1.604965@1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.604980@1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.604994@1] usb usb2: Product: DWC OTG Controller
[ 1.605007@1] usb usb2: Manufacturer: Linux 3.10.108 dwc_otg_hcd
[ 1.605019@1] usb usb2: SerialNumber: lm0
[ 1.605842@1] hub 2-0:1.0: USB hub found
[ 1.605872@1] hub 2-0:1.0: 1 port detected
[ 1.606410@1] boot_device_flag : 1
[ 1.606423@1] ===========================================amlnf_init:642,nand device tree ok,dev-name:nand
[ 1.606444@1] Nand PHY driver Version: 1.01.001.0006 (c) 2013 Amlogic Inc.
[ 1.606457@1] amlnf_phy_init : amlnf init flag 0
[ 1.606568@1] ######STS IRQ mode for nand driver
[ 1.606655@1] NAND device id: 2c 44 44 4b a9 0 0 0
[ 1.606670@1] detect NAND device: D revision NAND 4GiB MT29F32G08CBADA
[ 1.653294@1] AML_NAND_NEW_OOB : new oob
[ 1.653313@1] bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
[ 1.653324@1] boot_device_flag = 1
[ 1.654417@1] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
[ 1.659523@1] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0
[ 1.659907@1] nand shipped bbt at block 6
[ 1.679638@1] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 7
[ 1.680019@1] i=0,register --- nand_key
[ 1.700029@1] NAND CKECK : arg nenv: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 72
[ 1.703545@1] nand adjust phy offset : block 4
[ 1.703579@1] nand adjust phy offset : block 4
[ 1.703637@1] nfboot : offset: 0x000000000000 -0x000000800000 : partitons 0 : single_chip single_plane
[ 1.703650@1] nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
[ 1.703663@1] nfcode : offset: 0x00002b000000 -0x000052800000 : partitons 6 : single_chip multi_plane
[ 1.703675@1] nfdata : offset: 0x00007d800000 -0x000082800000 : partitons 1 : single_chip multi_plane
[ 1.703795@1] bad block count = 0
[ 1.703795@1]
[ 1.707438@1] bad block count = 0
[ 1.707438@1]
[ 1.715713@1] bad block count = 0
[ 1.715713@1]
[ 1.728801@1] bad block count = 0
[ 1.728801@1]
[ 1.728817@1] amlnand_add_nftl:
[ 1.729264@1] Creating 1 ntd partitions
[ 1.729278@1] block_num 146
[ 1.732915@1] ------init_ntd
[ 1.733626@1] ntd: Giving out device 0 to nfcache
[ 1.733639@1] Creating 6 ntd partitions
[ 1.733658@1] block_num 330
[ 1.742456@1] ntd: Giving out device 1 to nfcode
[ 1.742470@1] Creating 1 ntd partitions
[ 1.742482@1] block_num 522
[ 1.756011@1] ntd: Giving out device 2 to nfdata
[ 1.756993@1] boot_device_flag : 1
[ 1.757005@1] register_ntd_blktrans start
[ 1.757018@1] ntd device 250!
[ 1.757027@1] ntd->name: nfcache
[ 1.757041@1] adjust_block_num : 4,reserved_block_ratio 10
[ 1.757054@1] nftl version 140911a
[ 1.757082@1] nftl part attr 0
[ 1.758475@3] Indeed it is in host mode hprt0 = 00021501
[ 1.760872@1] size_in_blk 146; total_block 145;
[ 1.760885@1] nftl start:145,17
[ 1.761187@1] first
[ 1.809899@1] average_erase_count:1
[ 1.809915@1] second 144,128
[ 1.809924@1] part->max_discard_block = 4
[ 1.897996@1] all block full!!
[ 1.898011@1] all discard block full!!
[ 1.898095@1] free list:
[ 1.898104@1] free block cnt = 11
[ 1.898115@1] new current block is 86
[ 1.898122@1] total discard page count is 0
[ 1.898134@1] create_part_list:1235,current_used_discard_block=40,current_discard_block_used_count=453
[ 1.899166@1] unmappig_pages=9023,discarded_pages=0,mapping_pages=23745
[ 1.899178@1] nftl ok!
[ 1.899979@1] Enable QUEUE_FLAG_DISCARD for NFTL
[ 1.900841@1] aml_nftl_add_ntd ok
[ 1.900856@1] ntd device 250!
[ 1.900864@1] ntd->name: nfcode
[ 1.900878@1] adjust_block_num : 4,reserved_block_ratio 10
[ 1.900890@1] nftl version 140911a
[ 1.900947@1] nftl part attr 0
[ 1.909260@1] nftl start:330,34
[ 1.909834@1] first
[ 1.938430@3] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.938550@3] Indeed it is in host mode hprt0 = 00001101
[ 2.020817@1] average_erase_count:1
[ 2.020836@1] second 322,296
[ 2.020845@1] part->max_discard_block = 4
[ 2.138906@3] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101
[ 2.138926@3] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.138939@3] usb 1-1: Product: USB 2.0 Hub
[ 2.139920@3] hub 1-1:1.0: USB hub found
[ 2.140021@3] hub 1-1:1.0: 4 ports detected
[ 2.218258@1] all block full!!
[ 2.218273@1] all discard block full!!
[ 2.218616@1] free list:
[ 2.218629@1] free block cnt = 136
[ 2.218639@1] new current block is 251
[ 2.218648@1] total discard page count is 0
[ 2.218659@1] create_part_list:1235,current_used_discard_block=238,current_discard_block_used_count=559
[ 2.220985@1] unmappig_pages=34564,discarded_pages=0,mapping_pages=41212
[ 2.220994@1] nftl ok!
[ 2.222044@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.223016@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.223912@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.224797@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.225697@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.226586@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.227302@2] aml_nftl_add_ntd ok
[ 2.227316@2] ntd device 250!
[ 2.227326@2] ntd->name: nfdata
[ 2.227340@2] adjust_block_num : 4,reserved_block_ratio 10
[ 2.227353@2] nftl version 140911a
[ 2.227436@2] nftl part attr 0
[ 2.240525@2] nftl start:522,52
[ 2.241517@2] first
[ 2.254813@2] found discard block:39
[ 2.377593@2] found discard block:407
[ 2.415982@2] average_erase_count:43
[ 2.416003@2] second 521,470
[ 2.416012@2] part->max_discard_block = 4
[ 2.418502@3] usb 1-1.4: new high-speed USB device number 3 using dwc_otg
[ 2.519302@3] usb 1-1.4: New USB device found, idVendor=0bda, idProduct=8179
[ 2.519322@3] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.519345@3] usb 1-1.4: Product: 802.11n NIC
[ 2.519358@3] usb 1-1.4: Manufacturer: Realtek
[ 2.519371@3] usb 1-1.4: SerialNumber: 9C443D209D6C
[ 2.734806@2] all block full!!
[ 2.913899@2] currnet_discard_block1:39
[ 2.930631@2] reach the last discard page:23
[ 2.931396@2] free list:
[ 2.931406@2] free block cnt = 9
[ 2.931416@2] new current block is 146
[ 2.931425@2] total discard page count is 278
[ 2.931437@2] create_part_list:1235,current_used_discard_block=39,current_discard_block_used_count=134
[ 2.934987@2] unmappig_pages=11252,discarded_pages=387,mapping_pages=108681
[ 2.934996@2] nftl ok!
[ 2.936055@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 2.936886@2] aml_nftl_add_ntd ok
[ 2.936912@2] init_aml_nftl end
[ 2.940962@3] amvideocap_init_module
[ 2.941297@3] Amlogic A/V streaming port init
[ 2.944967@3] buffersize=262144,0,start=0
[ 2.944990@3] Subtitle stbuf alloced at 0xdb400000, size = 262144
[ 2.945002@3] changed the (2) buffer size from 0 to 262144
[ 2.945514@3] init vdec memsource 7a00000->b9fffff
[ 2.945926@3] [tsync_pcr_init]init success.
[ 2.946137@3] regist mpeg12 codec profile
[ 2.946342@3] regist mpeg4 codec profile
[ 2.946353@3] amvdec_vc1 module init
[ 2.946550@3] regist vc1 codec profile
[ 2.946570@3] amvdec_h264 module init
[ 2.946825@3] regist h264 codec profile
[ 2.946837@3] amvdec_h264mvc module init
[ 2.947031@3] regist hmvc codec profile
[ 2.947043@3] amvdec_h265 module init
[ 2.947253@3] regist hevc codec profile
[ 2.947468@3] regist mjpeg codec profile
[ 2.947479@3] amvdec_real module init
[ 2.947672@3] regist real codec profile
[ 2.947692@3] amvdec_avs module init
[ 2.948129@3] amvenc_avc memory resource undefined.
[ 2.948142@3] amvenc_avc memory is invaild, probe fail!
[ 2.948163@3] amvenc_avc: probe of amvenc_avc.0 failed with error -14
[ 2.948480@3] jpegenc module init
[ 2.949081@3] alloc_keep_buffer keep_y_addr dae00000
[ 2.949110@3] alloc_keep_buffer keep_u_addr db500000
[ 2.949129@3] alloc_keep_buffer keep_v_addr db480000
[ 2.949140@3] yaddr=dae00000,u_addr=db500000,v_addr=db480000
[ 2.949862@3] create_ge2d_work_queue video task ok
[ 2.950836@3] efuse===========================================
[ 2.951304@3] efuse: device efuse created
[ 2.951507@3] efuse--------------------------------------------
[ 2.951519@3] SARADC Driver init.
[ 2.951802@3] saradc_probe
[ 3.098529@3] saradc calibration: ref_val = 510
[ 3.098542@3] saradc calibration: ref_nominal = 512
[ 3.098551@3] saradc calibration: coef = 4136
[ 3.099243@3] ir irblaster probe
[ 3.099898@3] Remote Driver
[ 3.100026@3] Remote platform_data g_remote_base=fe600580
[ 3.100075@3] set drvdata completed
[ 3.100097@3] device_create_file completed
[ 3.100866@3] input: aml_keypad as /devices/platform/meson-remote/input/input0
[ 3.101528@3] input_register_device completed
[ 3.101612@3] [0xffffff00] = 0x1dd0190
[ 3.101622@3] [0xffffff04] = 0xf800ca
[ 3.101631@3] [0xffffff08] = 0x82006e
[ 3.101640@3] [0xffffff0c] = 0x3c0030
[ 3.101649@3] [0xffffff10] = 0x30fa0013
[ 3.101657@3] [0xffffff18] = 0x6f19000
[ 3.101666@3] [0xffffff1c] = 0xbe40
[ 3.101674@3] [0x0] = 0xfa00a0
[ 3.101682@3] [0x4] = 0xfa00a0
[ 3.101690@3] [0x8] = 0xfa00a0
[ 3.101699@3] [0xc] = 0x640030
[ 3.101707@3] [0x10] = 0x30fa0013
[ 3.101716@3] [0x18] = 0x961b800
[ 3.101724@3] [0x1c] = 0x9740
[ 3.101740@3] [0x20] = 0x104
[ 3.101748@3] [0x24] = 0x0
[ 3.101756@3] [0x28] = 0x0
[ 3.101765@3] set_remote_mode[69]
[ 3.101804@3] remote config major:236
[ 3.102270@3] physical address:0x1cb8a000
[ 3.102466@3] Meson KeyInput init
[ 3.102754@3] GPIO Keypad Driver init.
[ 3.102861@3] ==gpio_key_probe==
[ 3.102917@3] reg:2620,clearmask=400040,setmask=1
[ 3.102929@3] reg:2622,clearmask=ff0000,set pin=86
[ 3.102939@3] reg:2623,clearmask=7000000,setmask=7
[ 3.102950@3] reg:2620,clearmask=800080,setmask=10001
[ 3.102960@3] reg:2622,clearmask=ff000000,set pin=86
[ 3.102970@3] reg:2623,clearmask=70000000,setmask=7
[ 3.103029@3] power key(116) registed.
[ 3.103411@3] input: gpio_keypad as /devices/platform/gpio_keypad.5/input/input1
[ 3.103758@3] gpio keypad register input device completed.
[ 3.103779@3] gpio keypad major:235
[ 3.104413@3] spi_nor_init
[ 3.104693@3] amlogic_spi_nor_probe:
[ 3.104712@3] amlogic_spi->state_name:default
[ 3.105026@3] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
[ 3.105280@3] check_storage_device : spi boot_device_flag : -1
[ 3.105292@3] spi_nor_probe
[ 3.105302@3] spi_nor_probe 629 boot_device_flag 1 : do not init spi
[ 3.105322@3] spi_nor: probe of apollospi:32766 failed with error -12
[ 3.105336@3] amlogic_spi_nor_probe over
[ 3.105600@3] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 3.105911@3] host->base fe108c20
[ 3.105973@3] pdata->caps 7
[ 3.105995@3] pdata->caps2 0
[ 3.106008@3] get property: port, value:0x00000001
[ 3.106018@3] get property: ocr_avail, value:0x00200000
[ 3.106029@3] get property: f_min, value:0x000493e0
[ 3.106039@3] get property: f_max, value:0x02faf080
[ 3.106050@3] get property: f_max_w, value:0x02faf080
[ 3.106060@3] get property: max_req_size, value:0x00020000
[ 3.106071@3] get property: irq_in, value:0x00000003
[ 3.106083@3] get property: irq_out, value:0x00000005
[ 3.106110@3] get property: gpio_cd, str:CARD_6
[ 3.106123@3] get property: pinname, str:sd
[ 3.106136@3] get property: jtag_pin, str:CARD_0
[ 3.106147@3] get property: card_type, value:0x00000005
[ 3.106159@3] get property: gpio_dat3, str:CARD_4
[ 3.106186@3] normal card in
[ 3.138444@2] sd: mmc_rescan_try_freq: trying to init card at 400000 Hz
[ 3.138463@3] reg:2620,clearmask=80008,setmask=10001
[ 3.138478@3] reg:2621,clearmask=ff000000,set pin=49
[ 3.138488@3] reg:2623,clearmask=7000,setmask=7
[ 3.138510@3] reg:2620,clearmask=200020,setmask=1
[ 3.138521@3] reg:2622,clearmask=ff00,set pin=49
[ 3.138531@3] reg:2623,clearmask=700000,setmask=7
[ 3.138800@0] pdata->caps 10f
[ 3.138813@0] pdata->caps2 0
[ 3.138825@0] get property: port, value:0x00000000
[ 3.138835@0] get property: ocr_avail, value:0x00200000
[ 3.138846@0] get property: f_min, value:0x000493e0
[ 3.138856@0] get property: f_max, value:0x02faf080
[ 3.138867@0] get property: max_req_size, value:0x00020000
[ 3.138884@0] get property: pinname, str:sdio
[ 3.138895@0] get property: card_type, value:0x00000003
[ 3.170316@0] sd: new high speed SDHC card at address 8dbd, clock 39843750, 4-bit-bus-width
[ 3.170894@0] mmcblk0: sd:8dbd SU08G 7.40 GiB
[ 3.210381@0] mmcblk0: p1 p2
[ 3.318411@2] [aml_sdio_probe] aml_sdio_probe() success!
[ 3.319902@3] host->base fe108e00
[ 3.320009@3] pdata->caps 80000547
[ 3.320020@3] pdata->caps2 0
[ 3.320032@3] get property: port, value:0x00000005
[ 3.320051@3] get property: ocr_avail, value:0x00200000
[ 3.320062@3] get property: f_min, value:0x000493e0
[ 3.320073@3] get property: f_max, value:0x02faf080
[ 3.320084@3] get property: max_req_size, value:0x00020000
[ 3.320101@3] get property: pinname, str:emmc
[ 3.320112@3] get property: card_type, value:0x00000001
[ 3.320128@3] get property: gpio_dat3, str:BOOT_3
[ 3.320139@3] [is_emmc_exist] host->storage_flag=1, POR_BOOT_VALUE=7
[ 3.320148@3] [aml_sdhc_probe]: there is not eMMC/tsd, skip sdhc_c dts config!
[ 3.368398@3] [aml_sdhc_probe] aml_sdhc_probe() success!
[ 3.368668@3] [dsp]DSP start addr 0xc5e00000
[ 3.368723@3] [dsp]register dsp to char divece(257)
[ 3.369730@3] amlogic audio spdif interface device init!
[ 3.369836@3] name=nand_key nand_key
[ 3.370636@3] register_aes_algorithm:488,new way
[ 3.370688@3] unkown current key-name,key_read_show:1396
[ 3.370699@3] get keyexample fail, aml_rtc_probe:755
[ 3.371659@3] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
[ 3.376324@0] amaudio2: device amaudio2 created
[ 3.376608@0] Amlogic CEC Driver, (c) 2016 Gerald Dachs, Version: 0.0.1
[ 3.376979@0] Error: Didn't get power valid value --- wifi_power_probe 323
[ 3.376999@0] wifi_power power_gpio is 6
[ 3.377012@0] wifi_power power_gpio2 is 108
[ 3.378060@0] UMP: UMP device driver -02284d8 loaded
[ 3.378576@0] aml_aes aml_aes: Aml AES
[ 3.379253@0] aml_tdes aml_tdes: Aml TDES
[ 3.380670@0] enter rt5616_modinit
[ 3.381519@0] == ES8323 == es8323_modinit()
[ 3.382296@0] enter aml_i2s_dai_probe
[ 3.382310@0] i2s get no clk src setting in dts, use the default mpll 0
[ 3.382328@0] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
[ 3.382626@0] enter aml_pcm_dai_probe
[ 3.382838@0] [aml-spdif-dai]enter aml_dai_spdif_init
[ 3.382854@0] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 3.382863@0] audio_set_958_clk, freq=4,
[ 3.382877@0] IEC958 16bit
[ 3.382888@0] hdmitx: audio: aout notify rate 48000
[ 3.382897@0] hdmitx: audio: aout notify size 16
[ 3.382906@0] hdmitx: audio: aout notify format CT_PCM
[ 3.382993@0] [aml-spdif-dai]aml_spdif_probe
[ 3.383279@0] test codec rt5616
[ 3.383294@0] test_codec_of_node, node rt5616 disable
[ 3.383304@0] test codec rt5631
[ 3.383313@0] test_codec_of_node, node rt5631 disable
[ 3.383322@0] test codec wm8960
[ 3.383331@0] test_codec_of_node, node wm8960 disable
[ 3.383341@0] test codec dummy_codec
[ 3.383349@0] test_codec_of_node, node dummy_codec disable
[ 3.383358@0] no external codec, using aml default codec
[ 3.383626@0] enter spdif_dit_probe
[ 3.383637@0] aml_spdif_unmute
[ 3.383983@0] codec_name = aml_m8_codec.0
[ 3.384836@0] enter aml_asoc_init
[ 3.384887@0] p_aml_audio->hp_disable=1
[ 3.384898@0] falied to get spk event delay time paraments from dts file
[ 3.384907@0] spk_event delay_time = 0
[ 3.385899@0] aml-i2s 0:playback preallocate_dma_buffer: area=dd701000, addr=1ae00000, size=524288
[ 3.386145@0] aml-i2s 1:capture preallocate_dma_buffer: area=dd783000, addr=1b660000, size=65536
[ 3.386186@0] aml_snd_m8 aml_m8_sound_card.4: AML-M8 <-> aml-i2s-dai.0 mapping ok
[ 3.387396@0] aml-i2s 0:playback preallocate_dma_buffer: area=dd7a4000, addr=1af00000, size=524288
[ 3.387642@0] aml-i2s 1:capture preallocate_dma_buffer: area=dd826000, addr=1aec0000, size=65536
[ 3.387683@0] aml_snd_m8 aml_m8_sound_card.4: dit-hifi <-> aml-spdif-dai.0 mapping ok
[ 3.389940@0] -----ext_codec=0---
[ 3.389971@0] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
[ 3.390663@1] TCP: cubic registered
[ 3.391697@1] NET: Registered protocol family 10
[ 3.392726@2] NET: Registered protocol family 17
[ 3.392838@2] Key type dns_resolver registered
[ 3.393703@2] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 3.393745@2] Registering SWP/SWPB emulation handler
[ 3.393757@2] enter meson_pm_init
[ 3.393921@2] enter meson_pm_probe!
[ 3.393937@2] meson_pm_probe done !
[ 3.393957@2] pm-meson: probe of aml_pm_m8 failed with error -1
[ 3.395842@2] regulator-dummy: disabling
[ 3.396462@2] console [netcon0] enabled
[ 3.396474@2] netconsole: network logging started
[ 3.396922@2] aml_rtc rtc.0: setting system clock to 1970-01-01 00:00:44 UTC (44)
[ 3.397075@2] meson_cpufreq: no voltage_control prop
[ 3.397086@2] voltage_control = 0
[ 3.398266@2] buf[0]=ed,buf[1]=af,err=4
[ 3.398275@2] adc=383,TS_C=13,flag=1
[ 3.398280@2] efuse_flag=a
[ 3.398286@2] amlogic_thermal_probe, this chip is trimmed, use thermal
[ 3.398293@2] amlogic-thermal aml_thermal: amlogic thermal probe start
[ 3.398300@2] #thermal-cells=7
[ 3.398305@2] pdata->temp_trip_count=7
[ 3.398313@2] temperature=60000 on trip point=0
[ 3.398318@2] fixing high_freq=1536001 to 1536000 at trip point 0,level=0
[ 3.398327@2] fixing low_freq=1536001 to 1536000 at trip point 0,level=0
[ 3.398335@2] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
[ 3.398340@2] cpu[0] core num==3
[ 3.398344@2] gpu[0] core num==2
[ 3.398349@2] temperature=65000 on trip point=1
[ 3.398353@2] fixing high_freq=1488001 to 1488000 at trip point 1,level=1
[ 3.398359@2] fixing low_freq=1488001 to 1488000 at trip point 1,level=1
[ 3.398390@2] gpu[1].gpu_high_freq=426,tmp_level[1].gpu_high_freq=426
[ 3.398396@2] cpu[1] core num==3
[ 3.398400@2] gpu[1] core num==2
[ 3.398405@2] temperature=70000 on trip point=2
[ 3.398409@2] fixing high_freq=1320001 to 1296000 at trip point 2,level=3
[ 3.398416@2] fixing low_freq=1320001 to 1296000 at trip point 2,level=3
[ 3.398423@2] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
[ 3.398428@2] cpu[2] core num==2
[ 3.398432@2] gpu[2] core num==2
[ 3.398437@2] temperature=75000 on trip point=3
[ 3.398441@2] fixing high_freq=1200001 to 1200000 at trip point 3,level=4
[ 3.398447@2] fixing low_freq=1200001 to 1200000 at trip point 3,level=4
[ 3.398455@2] gpu[3].gpu_high_freq=328,tmp_level[3].gpu_high_freq=328
[ 3.398460@2] cpu[3] core num==2
[ 3.398464@2] gpu[3] core num==1
[ 3.398469@2] temperature=80000 on trip point=4
[ 3.398473@2] fixing high_freq=1008001 to 1008000 at trip point 4,level=6
[ 3.398479@2] fixing low_freq=1008001 to 1008000 at trip point 4,level=6
[ 3.398487@2] gpu[4].gpu_high_freq=328,tmp_level[4].gpu_high_freq=328
[ 3.398491@2] cpu[4] core num==2
[ 3.398496@2] gpu[4] core num==1
[ 3.398500@2] temperature=90000 on trip point=5
[ 3.398504@2] fixing high_freq=720001 to 696000 at trip point 5,level=9
[ 3.398511@2] fixing low_freq=720001 to 696000 at trip point 5,level=9
[ 3.398518@2] gpu[5].gpu_high_freq=251,tmp_level[5].gpu_high_freq=251
[ 3.398523@2] cpu[5] core num==1
[ 3.398527@2] gpu[5] core num==1
[ 3.398532@2] temperature=260000 on trip point=6
[ 3.398536@2] fixing high_freq=-1 to -22 at trip point 6,level=-1
[ 3.398542@2] fixing low_freq=-1 to -22 at trip point 6,level=-1
[ 3.398550@2] gpu[6].gpu_high_freq=-1,tmp_level[6].gpu_high_freq=-1
[ 3.398554@2] cpu[6] core num==-1
[ 3.398559@2] gpu[6] core num==-1
[ 3.398564@2] idle interval=1000
[ 3.398569@2] pdata->name:aml_thermal
[ 3.399157@2] tmp_trip[0].cpu_core_upper=1
[ 3.399174@2] tmp_trip[1].cpu_core_upper=1
[ 3.399187@2] tmp_trip[2].cpu_core_upper=2
[ 3.399199@2] tmp_trip[3].cpu_core_upper=2
[ 3.399211@2] tmp_trip[4].cpu_core_upper=2
[ 3.399223@2] tmp_trip[5].cpu_core_upper=3
[ 3.399235@2] tmp_trip[6].cpu_core_upper=-1
[ 3.399248@2] aml_thermal bind thermal-cpucore-0 okay !
[ 3.399311@2] aml_thermal bind thermal-cpufreq-0 okay !
[ 3.399450@2] amlogic: Kernel Thermal management registered
[ 3.399458@2] amlogic-thermal aml_thermal: amlogic thermal probe done
[ 3.399626@2] ALSA device list:
[ 3.399634@2] #0: AML-M8AUDIO
[ 3.399921@2] Freeing unused kernel memory: 188K
[ 3.448335@1] tvmode set to 576cvbs
[ 3.448335@1]
[ 3.448356@1] don't set the same mode as current.
[ 3.555130@1] vfm_map_store:rm default
[ 3.555130@1]
[ 3.555328@1] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 3.555328@1]
[ 3.606581@3] Checking disk(s): LABEL=LIBREELEC LABEL=STORAGE
[ 3.613506@1] aml_nftl_open ok!
[ 3.613848@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.646139@1] aml_nftl_open ok!
[ 3.646754@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.663654@3] aml_nftl_open ok!
[ 3.663831@3] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.679311@3] aml_nftl_open ok!
[ 3.679475@3] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.682468@3] aml_nftl_open ok!
[ 3.682644@3] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.685659@3] aml_nftl_open ok!
[ 3.685830@3] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.701078@3] aml_nftl_open ok!
[ 3.701249@3] blktrans_ioctl -cmd: 5331,801c0204,64
[ 3.820702@2] aml_nftl_open ok!
[ 3.820966@2] blktrans_ioctl -cmd: 5331,801c0204,64
[ 4.600320@2] IRQ94 no longer affine to CPU2
[ 4.600530@1] CPU2: shutdown
[ 4.603036@3] fsck: CP437: Invalid argument
[ 4.603194@3] fsck: fsck.fat 4.1 (2017-01-24)
[ 4.603387@3] fsck: /dev/mmcblk0p1: 10 files, 17004/65501 clusters
[ 4.603598@3] fsck: STORAGE: clean, 11/1808384 files, 235780/7233536 blocks
[ 4.645084@1] aml_nftl_open ok!
[ 4.654582@1] aml_nftl_open ok!
[ 4.664231@1] aml_nftl_open ok!
[ 4.673606@1] aml_nftl_open ok!
[ 4.674406@1] aml_nftl_open ok!
[ 4.675234@1] aml_nftl_open ok!
[ 4.678797@3] IRQ62 no longer affine to CPU3
[ 4.678801@3] IRQ63 no longer affine to CPU3
[ 4.678819@3] IRQ95 no longer affine to CPU3
[ 4.679031@1] CPU3: shutdown
[ 4.685155@1] aml_nftl_open ok!
[ 4.694846@1] aml_nftl_open ok!
[ 4.911438@0] aml_nftl_open ok!
[ 4.912273@0] aml_nftl_open ok!
[ 4.922068@0] aml_nftl_open ok!
[ 4.931484@0] aml_nftl_open ok!
[ 4.932331@0] aml_nftl_open ok!
[ 4.933162@0] aml_nftl_open ok!
[ 4.942813@0] aml_nftl_open ok!
[ 4.952361@0] aml_nftl_open ok!
[ 4.956643@0] force enable DISCARD here for ext4 fs
[ 4.956658@0] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 4.957337@0] force enable DISCARD here for ext4 fs
[ 4.957354@0] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[ 4.957985@0] force enable DISCARD here for ext4 fs
[ 5.002396@1] checked enable EXT4 DISCARD here
[ 5.002410@1] EXT4-fs (mmcblk0p2): mounting with "discard" option, but the device does not support discard
[ 5.002417@1] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 5.592116@1] systemd[1]: System time before build time, advancing clock.
[ 5.656813@1] systemd[1]: systemd 242 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD +IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[ 5.657207@1] systemd[1]: Detected architecture arm.
[ 5.657300@1] systemd[1]: Running with unpopulated /etc.
[ 5.657613@1] systemd[1]: Set hostname to .
[ 5.657732@1] systemd[1]: Cannot open /etc/machine-id: No such file or directory
[ 6.048203@1] systemd[1]: Populated /etc with preset unit settings.
[ 6.075691@0] systemd[1]: File /usr/lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 6.075714@0] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 6.202170@0] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.202619@0] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 6.204753@0] systemd[1]: Starting Show Version...
[ 6.205315@0] systemd[1]: Created slice User and Session Slice.
[ 6.206748@0] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 6.207805@0] systemd[1]: Listening on udev Control Socket.
[ 6.208068@0] systemd[1]: Reached target Paths.
[ 6.208884@0] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.211287@0] systemd[1]: Starting Debug Shell on /dev/ttyS0...
[ 6.212459@0] systemd[1]: Listening on Journal Socket.
[ 6.214904@0] systemd[1]: Starting Wait For Kernel Time Synchronized...
[ 6.217366@0] systemd[1]: Mounting Variable Directory...
[ 6.218045@0] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 6.221107@0] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.223639@0] systemd[1]: Mounting Kernel Debug File System...
[ 6.226639@0] systemd[1]: Starting Setup NTP servers for timesyncd...
[ 6.226931@0] systemd[1]: Reached target RPC Port Mapper.
[ 6.228443@1] Changing uart_ao_ttyS0: baud from 0 to 115200
[ 6.229718@0] systemd[1]: Starting Create Persistent Log Directory on /storage...
[ 6.229977@0] systemd[1]: Reached target Slices.
[ 6.230749@0] systemd[1]: Listening on udev Kernel Socket.
[ 6.231260@0] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 6.232365@0] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 6.261983@1] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 6.271982@1] systemd[1]: Started Show Version.
[ 6.274679@1] systemd[1]: Started Debug Shell on /dev/ttyS0.
[ 6.275583@1] systemd[1]: Mounted Variable Directory.
[ 6.276261@1] systemd[1]: Mounted POSIX Message Queue File System.
[ 6.276882@1] systemd[1]: Mounted Kernel Debug File System.
[ 6.279471@1] systemd[1]: Starting Create kernel modules tree from overlays...
[ 6.292596@0] systemd[1]: Started Create Persistent Log Directory on /storage.
[ 6.293685@0] systemd[1]: Condition check resulted in Persistent Log Storage being skipped.
[ 6.302816@0] systemd[1]: Started Setup NTP servers for timesyncd.
[ 6.346882@1] kernel-overlays-setup: setup base modules
[ 6.396317@0] kernel-overlays-setup: added modules from /usr/lib/kernel-overlays/base/lib/modules/3.10.108
[ 6.456758@1] kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware
[ 6.456971@1] kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays
[ 6.457269@1] kernel-overlays-setup: done
[ 6.458986@0] systemd[1]: kernel-overlays.service: Succeeded.
[ 6.459313@0] systemd[1]: Started Create kernel modules tree from overlays.
[ 6.461671@0] systemd[1]: Starting udev Coldplug all Devices...
[ 6.465266@0] systemd[1]: Starting Load Kernel Modules...
[ 6.467648@0] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 6.468240@0] systemd[1]: Condition check resulted in Mounting swapfile being skipped.
[ 6.468943@0] systemd[1]: Reached target Swap.
[ 6.471166@0] systemd[1]: Mounting Temporary Directory (/tmp)...
[ 6.473373@0] systemd[1]: Starting Setup machine-id...
[ 6.489146@0] systemd[1]: Mounted Temporary Directory (/tmp).
[ 6.489805@0] systemd[1]: Reached target Local File Systems.
[ 6.699444@1] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 6.752632@0] Linux video capture interface: v2.00
[ 6.836493@0] amlvideo-000: V4L2 device registered as video10
[ 6.847323@0] systemd[1]: Started Setup machine-id.
[ 6.849777@0] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 6.852040@0] systemd[1]: Starting Journal Service...
[ 6.879018@0] pdata->tmp_trip[0].gpu_lower_level=1
[ 6.879030@0] pdata->tmp_trip[0].gpu_upper_level=1
[ 6.879054@0] pdata->tmp_trip[1].gpu_lower_level=2
[ 6.879059@0] pdata->tmp_trip[1].gpu_upper_level=2
[ 6.879072@0] pdata->tmp_trip[2].gpu_lower_level=4
[ 6.879077@0] pdata->tmp_trip[2].gpu_upper_level=4
[ 6.879089@0] pdata->tmp_trip[3].gpu_lower_level=4
[ 6.879094@0] pdata->tmp_trip[3].gpu_upper_level=4
[ 6.879116@0] pdata->tmp_trip[4].gpu_lower_level=4
[ 6.879121@0] pdata->tmp_trip[4].gpu_upper_level=4
[ 6.879135@0] pdata->tmp_trip[5].gpu_lower_level=4
[ 6.879140@0] pdata->tmp_trip[5].gpu_upper_level=4
[ 6.879152@0] pdata->tmp_trip[6].gpu_lower_level=-1
[ 6.879157@0] pdata->tmp_trip[6].gpu_upper_level=-1
[ 6.879171@0] aml_thermal bind thermal-gpufreq-0 okay !
[ 6.879177@0] gpu cooling register okay with err=0
[ 6.888532@1] tmp_trip[0].gpu_core_upper=0
[ 6.888566@1] tmp_trip[1].gpu_core_upper=0
[ 6.888579@1] tmp_trip[2].gpu_core_upper=0
[ 6.888591@1] tmp_trip[3].gpu_core_upper=1
[ 6.888603@1] tmp_trip[4].gpu_core_upper=1
[ 6.888617@1] tmp_trip[5].gpu_core_upper=1
[ 6.888629@1] tmp_trip[6].gpu_core_upper=-1
[ 6.888642@1] aml_thermal bind thermal-gpucore-0 okay !
[ 6.888648@1] gpu core cooling register okay with err=0
[ 6.888917@1] Mali: Mali device driver loaded
[ 6.917643@0] systemd[1]: Started Create Static Device Nodes in /dev.
[ 6.948602@1] wireguard: WireGuard 1.0.20200908 loaded. See www.wireguard.com for information.
[ 6.948619@1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld [email protected]. All Rights Reserved.
[ 6.950043@0] systemd[1]: Started Load Kernel Modules.
[ 6.950808@0] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped.
[ 6.952478@0] systemd[1]: Starting Apply Kernel Variables...
[ 6.953045@0] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 6.989161@1] systemd[1]: Started Apply Kernel Variables.
[ 7.060035@1] systemd[1]: Started Journal Service.
[ 7.107841@0] systemd-journald[1535]: Received request to flush runtime journal from PID 1
[ 7.148698@2] CPU2: Booted secondary processor
[ 8.548431@1] -----hotplug:2
[ 8.588712@2] IRQ94 no longer affine to CPU2
[ 8.588925@1] CPU2: shutdown
[ 9.197988@0] Console: switching to colour dummy device 80x30
[ 9.288912@1] wifi_setup_dt
[ 9.288930@1] wifi_request_32k_clk : OFF-->ON for sdio_wifi
[ 9.288993@1] clock_32k_pin(107) : (null)
[ 9.289032@1] clock_32k_pin(107) : sdio_wifi
[ 9.291048@1] interrupt_pin(118) : (null)
[ 9.291085@1] reg:2620,clearmask=100010,setmask=0
[ 9.291096@1] reg:2622,clearmask=ff,set pin=118
[ 9.291107@1] reg:2623,clearmask=70000,setmask=4
[ 9.291118@1] interrupt_pin(118) : sdio_wifi
[ 9.291128@1] power_on_pin(6) : (null)
[ 9.291144@1] power_on_pin(6) : sdio_wifi
[ 9.291155@1] power_on_pin2(108) : (null)
[ 9.291175@1] power_on_pin2(108) : sdio_wifi
[ 9.361681@0] cur_mode = 0
[ 9.361694@0] [0x0] = 0x1dd0190
[ 9.361699@0] [0x4] = 0xf800ca
[ 9.361704@0] [0x8] = 0x82006e
[ 9.361708@0] [0xc] = 0x3c0030
[ 9.361713@0] [0x10] = 0x30fa0013
[ 9.361717@0] [0x18] = 0x6f19000
[ 9.361722@0] [0x1c] = 0x9f40
[ 9.361726@0] [0x20] = 0x0
[ 9.361730@0] [0x24] = 0x0
[ 9.361734@0] [0x28] = 0x0
[ 9.361739@0] set_remote_mode[69]
[ 9.448627@2] CPU2: Booted secondary processor
[ 9.598443@1] WIFI Disable! 6
[ 9.734397@1] cfg80211: Calling CRDA to update world regulatory domain
[ 9.736111@1] cfg80211: World regulatory domain updated:
[ 9.736130@1] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.736138@1] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (2000 mBi, 0 mBm)
[ 9.736145@1] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (2000 mBi, 0 mBm)
[ 9.736151@1] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (2000 mBi, 0 mBm)
[ 9.736158@1] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2000 mBi, 0 mBm)
[ 9.736164@1] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2000 mBi, 0 mBm)
[ 9.736170@1] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2000 mBi, 0 mBm)
[ 9.736177@1] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (2000 mBi, 0 mBm)
[ 9.736183@1] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 9.748659@3] CPU3: Booted secondary processor
[ 9.897309@1] aml_nftl_open ok!
[ 9.899146@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 9.902030@0] aml_nftl_open ok!
[ 9.903920@0] blktrans_ioctl -cmd: 5331,801c0204,64
[ 9.904150@2] aml_nftl_open ok!
[ 9.904738@1] aml_nftl_open ok!
[ 9.906469@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 9.908089@2] blktrans_ioctl -cmd: 5331,801c0204,64
[ 10.014108@1] aml_nftl_open ok!
[ 10.015648@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 10.027626@1] aml_nftl_open ok!
[ 10.029728@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 10.039813@1] aml_nftl_open ok!
[ 10.041134@1] blktrans_ioctl -cmd: 5331,801c0204,64
[ 10.057100@3] aml_nftl_open ok!
[ 10.058105@3] blktrans_ioctl -cmd: 5331,801c0204,64
[ 10.146949@0] eth0: device MAC address 00:01:23:cd:ee:af
[ 10.211821@0] bFWReady == _FALSE call reset 8051...
[ 10.272989@1] usbcore: registered new interface driver rtl8188eu
[ 10.300091@1] 8021q: 802.1Q VLAN Support v1.8
[ 9.560223@2] amlvideo openamlvideo close
[ 10.326173@2] amlvideo open==> rtl8188e_iol_efuse_patch
[ 11.423187@0] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.358650@0] -----hotplug:2
[ 12.419759@2] IRQ94 no longer affine to CPU2
[ 12.420005@1] CPU2: shutdown
[ 12.508726@3] IRQ95 no longer affine to CPU3
[ 12.508977@1] CPU3: shutdown
[ 10.326551@1] amlvideo close
[ 14.250139@1] amlvideo open<7>[ 15.087301@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.087326@0] IEC958 16bit
[ 15.087334@0] hdmitx: audio: aout notify rate 48000
[ 15.087339@0] hdmitx: audio: aout notify size 16
[ 15.087345@0] hdmitx: audio: no update
[ 15.087351@0] aml_i2s_close device type 8
[ 15.116697@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.116714@0] IEC958 16bit
[ 15.116722@0] hdmitx: audio: aout notify rate 48000
[ 15.116727@0] hdmitx: audio: aout notify size 16
[ 15.116731@0] hdmitx: audio: no update
[ 15.116738@0] aml_i2s_close device type 8
[ 15.120970@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.120998@0] IEC958 16bit
[ 15.121005@0] hdmitx: audio: aout notify rate 48000
[ 15.121026@0] hdmitx: audio: aout notify size 16
[ 15.121031@0] hdmitx: audio: no update
[ 15.121038@0] aml_i2s_close device type 8
[ 15.124905@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.124919@0] IEC958 16bit
[ 15.124926@0] hdmitx: audio: aout notify rate 48000
[ 15.124942@0] hdmitx: audio: aout notify size 16
[ 15.124947@0] hdmitx: audio: no update
[ 15.124964@0] aml_i2s_close device type 8
[ 15.126168@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.126190@0] IEC958 16bit
[ 15.126197@0] hdmitx: audio: aout notify rate 48000
[ 15.126202@0] hdmitx: audio: aout notify size 16
[ 15.126206@0] hdmitx: audio: no update
[ 15.126212@0] aml_i2s_close device type 8
[ 15.129048@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.129074@0] IEC958 16bit
[ 15.129081@0] hdmitx: audio: aout notify rate 48000
[ 15.129086@0] hdmitx: audio: aout notify size 16
[ 15.129091@0] hdmitx: audio: no update
[ 15.129097@0] aml_i2s_close device type 8
[ 15.131968@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.131984@0] IEC958 16bit
[ 15.131991@0] hdmitx: audio: aout notify rate 48000
[ 15.131996@0] hdmitx: audio: aout notify size 16
[ 15.132001@0] hdmitx: audio: no update
[ 15.132007@0] aml_i2s_close device type 8
[ 15.133206@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.133222@0] IEC958 16bit
[ 15.133229@0] hdmitx: audio: aout notify rate 48000
[ 15.133234@0] hdmitx: audio: aout notify size 16
[ 15.133239@0] hdmitx: audio: no update
[ 15.133245@0] aml_i2s_close device type 8
[ 15.134986@0] IEC958 16bit
[ 15.134999@0] hdmitx: audio: aout notify rate 48000
[ 15.135005@0] hdmitx: audio: aout notify size 16
[ 15.135009@0] hdmitx: audio: no update
[ 15.135017@0] aml_i2s_close device type 2
[ 15.144159@0] buf=0
[ 15.144173@0] IEC958_mode_raw=0
[ 15.144234@0] IEC958_mode_codec= 0,IEC958 type 2 CH PCM
[ 15.144240@0] last mode 0,now 0
[ 15.152148@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.152165@0] IEC958 16bit
[ 15.152173@0] hdmitx: audio: aout notify rate 48000
[ 15.152178@0] hdmitx: audio: aout notify size 16
[ 15.152182@0] hdmitx: audio: no update
[ 15.152196@0] aml_i2s_close device type 8
[ 15.154748@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 15.154905@0] IEC958 16bit
[ 15.154916@0] hdmitx: audio: aout notify rate 48000
[ 15.154922@0] hdmitx: audio: aout notify size 16
[ 15.154926@0] hdmitx: audio: no update
[ 15.154934@0] aml_i2s_close device type 8
[ 15.156844@0] enter aml_asoc_hw_params stream: playback rate: 44100 format: 2
[ 15.156908@0] [aml-i2s-dai]enterd aml_dai_i2s_prepare,old_samplerate:48000,sample_rate=44100
[ 15.156921@0] [aml-i2s-dai]i2s dma dd701000,phy addr 1ae00000,mode 0,ch 2
[ 15.156927@0] ----aml_hw_iec958_init,runtime->rate=44100--
[ 15.156935@0] [aml-spdif-dai]enterd aml_hw_iec958_init,set_clock:4,sample_rate=5
[ 15.156947@0] audio_set_958_clk, freq=5,
[ 15.156954@0] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 15.156959@0] iec958 mode PCM16
[ 15.156966@0] IEC958 16bit
[ 15.156972@0] hdmitx: audio: aout notify rate 44100
[ 15.156977@0] hdmitx: audio: aout notify size 16
[ 15.156983@0] [aml-spdif-dai]spdif dma dd701000,phy addr 1ae00000
[ 15.157113@0] enter:aml_m8_codec_mute_stream, mute=0, stream=0
[ 15.157250@0] [aml-i2s-dai]i2s dma dd701000,phy addr 1ae00000,mode 0,ch 2
[ 15.157258@0] ----aml_hw_iec958_init,runtime->rate=44100--
[ 15.157264@0] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 15.157270@0] iec958 mode PCM16
[ 15.157276@0] IEC958 16bit
[ 15.157282@0] hdmitx: audio: aout notify rate 44100
[ 15.157286@0] hdmitx: audio: aout notify size 16
[ 15.157291@0] hdmitx: audio: no update
[ 15.157296@0] [aml-spdif-dai]spdif dma dd701000,phy addr 1ae00000
[ 15.157379@0] enter:aml_m8_codec_mute_stream, mute=0, stream=0
[ 15.161010@0] [aml-i2s-dai]aiu i2s playback enable
[ 15.161010@0]
[ 15.161029@0] [aml-i2s-dai]audio_hw_958_enable 1
[ 14.250161@1] amlvideo closehdmitx: edid: not find mapped display mode
[ 19.448637@2] CPU2: Booted secondary processor
[ 19.748669@3] CPU3: Booted secondary processor
[ 19.858905@1] hdmitx: cec: Set PWM_E out put RTC 32K!
[ 19.858924@1] hdmitx: cec: enable:int mask:0x6
[ 19.859809@1] hdmitx: cec: enable:int mask:0x6
[ 20.948451@0] -----hotplug:2
[ 21.068789@2] IRQ94 no longer affine to CPU2
[ 21.069027@1] CPU2: shutdown
[ 21.178818@3] IRQ95 no longer affine to CPU3
[ 21.179065@1] CPU3: shutdown
[ 81.108562@0] [aml-i2s-dai]aiu i2s playback disable
[ 81.108562@0]
[ 81.108650@0] [aml-i2s-dai]audio_hw_958_enable 0
[ 81.108849@1] [aml-i2s-dai]i2s dma dd701000,phy addr 1ae00000,mode 0,ch 2
[ 81.108906@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 81.108951@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 81.108993@1] iec958 mode PCM16
[ 81.109035@1] IEC958 16bit
[ 81.109078@1] hdmitx: audio: aout notify rate 44100
[ 81.109115@1] hdmitx: audio: aout notify size 16
[ 81.109148@1] hdmitx: audio: no update
[ 81.109189@1] [aml-spdif-dai]spdif dma dd701000,phy addr 1ae00000
[ 81.109721@1] enter:aml_m8_codec_mute_stream, mute=0, stream=0
[ 91.110209@1] enter:aml_m8_codec_mute_stream, mute=1, stream=0
[ 91.110256@1] [aml-spdif-dai]enterd aml_spdif_play,set_clock:5,sample_rate=4
[ 91.110278@1] audio_set_958_clk, freq=4,
[ 91.110309@1] IEC958 16bit
[ 91.110334@1] hdmitx: audio: aout notify rate 48000
[ 91.110354@1] hdmitx: audio: aout notify size 16
[ 91.110381@1] aml_i2s_close device type 8
[ 108.642666@1] hdmitx: cec: rx msg num:0x01
[ 108.643039@1] hdmitx: cec: hdmitx: cec: rx buf clean
[ 627.249543@1] hdmitx: cec: waiting aocec free time out.
[ 627.250629@1] hdmitx: cec: waiting aocec free time out.
[ 627.251726@1] hdmitx: cec: waiting aocec free time out.
[ 627.252788@1] hdmitx: cec: waiting aocec free time out.
[ 627.253846@1] hdmitx: cec: waiting aocec free time out.
[ 627.254909@1] hdmitx: cec: waiting aocec free time out.
[ 627.256001@1] hdmitx: cec: waiting aocec free time out.
[ 627.257064@1] hdmitx: cec: waiting aocec free time out.
[ 627.258122@1] hdmitx: cec: waiting aocec free time out.
[ 627.507108@1] hdmitx: cec: waiting aocec free time out.
[ 627.508154@1] hdmitx: cec: waiting aocec free time out.
[ 627.893243@1] hdmitx: cec: waiting aocec free time out.
[ 627.894329@1] hdmitx: cec: waiting aocec free time out.
[ 628.279509@1] hdmitx: cec: waiting aocec free time out.
[ 628.280691@1] hdmitx: cec: waiting aocec free time out.
[ 628.665739@1] hdmitx: cec: waiting aocec free time out.
[ 628.666786@1] hdmitx: cec: waiting aocec free time out.
[ 629.051832@1] hdmitx: cec: waiting aocec free time out.
[ 629.052876@1] hdmitx: cec: waiting aocec free time out.
[ 629.249715@1] hdmitx: cec: hw reset :logical addr:0x11
[ 747.661039@1] hdmitx: cec: waiting aocec free time out.
[ 827.185789@0] hdmitx: cec: waiting aocec free time out.
[ 827.186966@0] hdmitx: cec: waiting aocec free time out.
[ 827.187989@0] hdmitx: cec: waiting aocec free time out.
[ 827.189227@0] hdmitx: cec: waiting aocec free time out.
[ 827.190374@0] hdmitx: cec: waiting aocec free time out.
[ 827.191512@0] hdmitx: cec: waiting aocec free time out.
[ 827.375606@1] hdmitx: cec: waiting aocec free time out.
[ 827.376691@1] hdmitx: cec: waiting aocec free time out.
[ 827.761272@1] hdmitx: cec: waiting aocec free time out.
[ 827.761837@1] hdmitx: cec: waiting aocec free time out.
[ 828.146723@1] hdmitx: cec: waiting aocec free time out.
[ 828.147613@1] hdmitx: cec: waiting aocec free time out.
[ 828.532791@1] hdmitx: cec: waiting aocec free time out.
[ 828.533973@1] hdmitx: cec: waiting aocec free time out.
[ 828.919020@1] hdmitx: cec: waiting aocec free time out.
[ 828.920065@1] hdmitx: cec: waiting aocec free time out.
[ 829.189689@0] hdmitx: cec: hw reset :logical addr:0x11
LibreELEC:~ #

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment