gistfile1.txt

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x517f803c]
[    0.000000] Linux version 5.3.0-rc6_2 (j@gravity) (gcc version 9.1.0 (GCC)) #1 SMP Wed Sep 4 06:09:46 UTC 2019
[    0.000000] Machine model: Lenovo Yoga C630
[    0.000000] earlycon: efifb0 at I/O port 0x0 (options '')
[    0.000000] printk: bootconsole [efifb0] enabled
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: EFI v2.60 by American Megatrends
[    0.000000] efi:  ACPI 2.0=0xffffd000  ESRT=0xdc601e18  SMBIOS=0xffe09000  MEMATTR=0xdc5fe418  RNG=0xe291bc18  MEMRESERVE=0xbb3f7e98 
[    0.000000] efi: seeding entropy pool
[    0.000000] esrt: Reserving ESRT space from 0x00000000dc601e18 to 0x00000000dc601e50.
[    0.000000] cma: Reserved 32 MiB at 0x00000000df800000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000027c79ffff]
[    0.000000] NUMA: NODE_DATA [mem 0x27b8fa840-0x27b8fbfff]
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000080000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000027c79ffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x00000000803fffff]
[    0.000000]   node   0: [mem 0x0000000080400000-0x0000000080d5ffff]
[    0.000000]   node   0: [mem 0x0000000081ac0000-0x00000000856fffff]
[    0.000000]   node   0: [mem 0x0000000085d00000-0x0000000085dfffff]
[    0.000000]   node   0: [mem 0x0000000085f00000-0x0000000085f0ffff]
[    0.000000]   node   0: [mem 0x0000000085f10000-0x0000000085fbffff]
[    0.000000]   node   0: [mem 0x000000008c417000-0x000000008c4fffff]
[    0.000000]   node   0: [mem 0x0000000097c00000-0x00000000994fffff]
[    0.000000]   node   0: [mem 0x0000000099500000-0x000000009ffcffff]
[    0.000000]   node   0: [mem 0x000000009ffd0000-0x000000009ffd9fff]
[    0.000000]   node   0: [mem 0x000000009ffdd000-0x000000009fffffff]
[    0.000000]   node   0: [mem 0x00000000a0000000-0x00000000e1b39fff]
[    0.000000]   node   0: [mem 0x00000000e1b3a000-0x00000000ffe59fff]
[    0.000000]   node   0: [mem 0x00000000ffe5a000-0x000000027c79ffff]
[    0.000000] Zeroed struct page in unavailable ranges: 502 pages
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000027c79ffff]
[    0.000000] On node 0 totalpages: 2004966
[    0.000000]   DMA32 zone: 6978 pages used for memmap
[    0.000000]   DMA32 zone: 0 pages reserved
[    0.000000]   DMA32 zone: 446534 pages, LIFO batch:63
[    0.000000]   Normal zone: 24351 pages used for memmap
[    0.000000]   Normal zone: 1558432 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] psci: OSI mode supported.
[    0.000000] percpu: Embedded 23 pages/cpu s56856 r8192 d29160 u94208
[    0.000000] pcpu-alloc: s56856 r8192 d29160 u94208 alloc=23*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation forced ON by KASLR
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] CPU features: detected: Hardware dirty bit management
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1973637
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinux-5.3.0-rc6_2 root=UUID=c436db96-0e54-42ce-8e4d-f2c65be7784e ro root=PARTUUID=637cbe98-d2db-4ae4-b513-022b30fdcd8f rw earlycon=efifb efi=novamap ignore_loglevel clk_ignore_unused pd_ignore_unused console=tty0
[    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0xd85fe000-0xdc5fe000] (64MB)
[    0.000000] Memory: 7192156K/8019864K available (12604K kernel code, 1932K rwdata, 5224K rodata, 5440K init, 460K bss, 794940K reserved, 32768K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: no VLPI support, no direct LPI support
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000017a60000
[    0.000000] ITS: No ITS available, not enabling LPIs
[    0.000000] random: get_random_bytes called from start_kernel+0x2f0/0x484 with crng_init=0
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000003] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.136977] Console: colour dummy device 80x25
[    0.273635] printk: console [tty0] enabled
[    0.410324] printk: bootconsole [efifb0] disabled
[    0.547050] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[    0.547062] pid_max: default: 32768 minimum: 301
[    0.547128] LSM: Security Framework initializing
[    0.547188] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.547208] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.548457] ASID allocator initialised with 32768 entries
[    0.548517] rcu: Hierarchical SRCU implementation.
[    0.550538] Remapping and enabling EFI services.
[    0.551041] smp: Bringing up secondary CPUs ...
[    0.552532] Detected VIPT I-cache on CPU1
[    0.552572] GICv3: CPU1: found redistributor 100 region 0:0x0000000017a80000
[    0.552625] CPU1: Booted secondary processor 0x0000000100 [0x517f803c]
[    0.554074] Detected VIPT I-cache on CPU2
[    0.554097] GICv3: CPU2: found redistributor 200 region 0:0x0000000017aa0000
[    0.554141] CPU2: Booted secondary processor 0x0000000200 [0x517f803c]
[    0.555710] Detected VIPT I-cache on CPU3
[    0.555731] GICv3: CPU3: found redistributor 300 region 0:0x0000000017ac0000
[    0.555771] CPU3: Booted secondary processor 0x0000000300 [0x517f803c]
[    0.557973] Detected VIPT I-cache on CPU4
[    0.557999] GICv3: CPU4: found redistributor 400 region 0:0x0000000017ae0000
[    0.558041] CPU4: Booted secondary processor 0x0000000400 [0x516f802d]
[    0.559981] Detected VIPT I-cache on CPU5
[    0.560008] GICv3: CPU5: found redistributor 500 region 0:0x0000000017b00000
[    0.560050] CPU5: Booted secondary processor 0x0000000500 [0x516f802d]
[    0.562149] Detected VIPT I-cache on CPU6
[    0.562177] GICv3: CPU6: found redistributor 600 region 0:0x0000000017b20000
[    0.562220] CPU6: Booted secondary processor 0x0000000600 [0x516f802d]
[    0.564494] Detected VIPT I-cache on CPU7
[    0.564524] GICv3: CPU7: found redistributor 700 region 0:0x0000000017b40000
[    0.564567] CPU7: Booted secondary processor 0x0000000700 [0x516f802d]
[    0.564646] smp: Brought up 1 node, 8 CPUs
[    0.564733] SMP: Total of 8 processors activated.
[    0.564741] CPU features: detected: Privileged Access Never
[    0.564746] CPU features: detected: LSE atomic instructions
[    0.564752] CPU features: detected: User Access Override
[    0.564757] CPU features: detected: 32-bit EL0 Support
[    0.564763] CPU features: detected: Common not Private translations
[    0.564770] CPU features: detected: RAS Extension Support
[    0.564775] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.564782] CPU features: detected: CRC32 instructions
[    0.566182] CPU: All CPU(s) started at EL1
[    0.566229] alternatives: patching kernel code
[    0.575440] devtmpfs: initialized
[    0.583329] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.583358] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.584197] pinctrl core: initialized pinctrl subsystem
[    0.585395] SMBIOS 3.0 present.
[    0.585414] DMI: LENOVO 81JL/LNVNB161216, BIOS 9UCN33WW(V2.06) 06/ 4/2019
[    0.585760] NET: Registered protocol family 16
[    0.586270] audit: initializing netlink subsys (disabled)
[    0.586400] audit: type=2000 audit(0.048:1): state=initialized audit_enabled=0 res=1
[    0.587405] cpuidle: using governor menu
[    0.587744] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.588424] DMA: preallocated 256 KiB pool for atomic allocations
[    0.589459] Serial: AMBA PL011 UART driver
[    0.606427] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.606440] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.606449] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.606458] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.612080] cryptd: max_cpu_qlen set to 1000
[    0.621996] ACPI: Interpreter disabled.
[    0.632013] vgaarb: loaded
[    0.632320] SCSI subsystem initialized
[    0.632470] libata version 3.00 loaded.
[    0.632643] usbcore: registered new interface driver usbfs
[    0.632674] usbcore: registered new interface driver hub
[    0.632744] usbcore: registered new device driver usb
[    0.633185] pps_core: LinuxPPS API ver. 1 registered
[    0.633194] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.633210] PTP clock support registered
[    0.633289] EDAC MC: Ver: 3.0.0
[    0.633930] qcom_scm firmware:scm: No available mechanism for setting download mode
[    0.634116] Registered efivars operations
[    0.634165] efivars: get_next_variable: status=8000000000000003
[    0.634626] FPGA manager framework
[    0.634677] Advanced Linux Sound Architecture Driver Initialized.
[    0.635420] clocksource: Switched to clocksource arch_sys_counter
[    0.635531] VFS: Disk quotas dquot_6.6.0
[    0.635575] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.635698] pnp: PnP ACPI: disabled
[    0.640016] thermal_sys: Registered thermal governor 'step_wise'
[    0.640019] thermal_sys: Registered thermal governor 'power_allocator'
[    0.641667] NET: Registered protocol family 2
[    0.641955] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.642045] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.642384] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    0.643112] TCP: Hash tables configured (established 65536 bind 65536)
[    0.643184] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.643336] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.643614] NET: Registered protocol family 1
[    0.643940] RPC: Registered named UNIX socket transport module.
[    0.643949] RPC: Registered udp transport module.
[    0.643956] RPC: Registered tcp transport module.
[    0.643963] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.643976] PCI: CLS 0 bytes, default 64
[    0.644092] Trying to unpack rootfs image as initramfs...
[    1.008628] Freeing initrd memory: 9208K
[    1.009635] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.009824] kvm [1]: HYP mode not available
[    1.109160] Initialise system trusted keyrings
[    1.109277] workingset: timestamp_bits=44 max_order=21 bucket_order=0
[    1.113716] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.114250] NFS: Registering the id_resolver key type
[    1.114275] Key type id_resolver registered
[    1.114284] Key type id_legacy registered
[    1.114298] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.114323] ntfs: driver 2.1.32 [Flags: R/W].
[    1.114581] 9p: Installing v9fs 9p2000 file system support
[    1.131301] NET: Registered protocol family 38
[    1.131321] Key type asymmetric registered
[    1.131332] Asymmetric key parser 'x509' registered
[    1.131367] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    1.131491] io scheduler mq-deadline registered
[    1.131499] io scheduler kyber registered
[    1.131594] io scheduler bfq registered
[    1.138282] efifb: probing for efifb
[    1.138332] efifb: framebuffer at 0x80400000, using 8100k, total 8100k
[    1.138341] efifb: mode is 1920x1080x32, linelength=7680, pages=1
[    1.138347] efifb: scrolling: redraw
[    1.138357] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.150310] Console: switching to colour frame buffer device 240x67
[    1.161451] fb0: EFI VGA frame buffer device
[    1.161750] EINJ: ACPI disabled.
[    3.195507] smps2: supplied by regulator-dummy
[    3.195723] smps3: supplied by regulator-dummy
[    3.195804] smps3: Setting 1352000-1352000uV
[    3.196045] smps4: supplied by regulator-dummy
[    3.196111] smps4: Setting 1800000-1800000uV
[    3.196338] smps5: supplied by regulator-dummy
[    3.196407] smps5: Setting 2040000-2040000uV
[    3.196630] smps7: supplied by regulator-dummy
[    3.196807] ldo1: supplied by regulator-dummy
[    3.196871] ldo1: Setting 880000-880000uV
[    3.197060] ldo2: supplied by smps3
[    3.197115] ldo2: Setting 1200000-1200000uV
[    3.197470] ldo3: supplied by regulator-dummy
[    3.197644] ldo5: supplied by regulator-dummy
[    3.197709] ldo5: Setting 800000-800000uV
[    3.197895] ldo6: supplied by regulator-dummy
[    3.197957] ldo6: Setting 1800000-1800000uV
[    3.198136] ldo7: supplied by smps5
[    3.198204] ldo7: Setting 1800000-1800000uV
[    3.198378] ldo8: supplied by smps3
[    3.198533] ldo9: supplied by regulator-dummy
[    3.198699] ldo10: supplied by regulator-dummy
[    3.198874] ldo11: supplied by regulator-dummy
[    3.199025] ldo12: supplied by smps5
[    3.199083] ldo12: Setting 1800000-1800000uV
[    3.199272] ldo13: supplied by regulator-dummy
[    3.199439] ldo14: supplied by smps5
[    3.199496] ldo14: Setting 1880000-1880000uV
[    3.199669] ldo15: supplied by smps5
[    3.199824] ldo16: supplied by regulator-dummy
[    3.199989] ldo17: supplied by smps3
[    3.200045] ldo17: Setting 1304000-1304000uV
[    3.200240] ldo18: supplied by regulator-dummy
[    3.200411] ldo19: supplied by regulator-dummy
[    3.200490] ldo19: Setting 3100000-3108000uV
[    3.202492] ldo20: supplied by regulator-dummy
[    3.204355] ldo20: Setting 2960000-2960000uV
[    3.206332] ldo21: supplied by regulator-dummy
[    3.208270] ldo22: supplied by regulator-dummy
[    3.210168] ldo23: supplied by regulator-dummy
[    3.212041] ldo24: supplied by regulator-dummy
[    3.213767] ldo24: Setting 3075000-3083000uV
[    3.215646] ldo25: supplied by regulator-dummy
[    3.217369] ldo25: Setting 3104000-3112000uV
[    3.219209] ldo26: supplied by regulator-dummy
[    3.220904] ldo26: Setting 1200000-1208000uV
[    3.222704] ldo28: supplied by regulator-dummy
[    3.224495] lvs1: supplied by regulator-dummy
[    3.226267] lvs2: supplied by regulator-dummy
[    3.230904] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    3.233961] SuperH (H)SCI(F) driver initialized
[    3.235950] msm_serial: driver initialized
[    3.237846] 898000.serial: ttyHS0 at MMIO 0x898000 (irq = 44, base_baud = 0) is a MSM
[    3.239714] serial serial0: tty port ttyHS0 registered
[    3.248557] loop: module loaded
[    3.251268] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
[    3.253065] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
[    3.254830] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
[    3.256908] ufshcd-qcom 1d84000.ufshc: ufs_qcom_init: required phy device. hasn't probed yet. err = -517
[    3.258679] ufshcd-qcom 1d84000.ufshc: ufshcd_variant_hba_init: variant qcom init failed err -517
[    3.260515] ufshcd-qcom 1d84000.ufshc: Initialization failed
[    3.263507] ufshcd-qcom 1d84000.ufshc: ufshcd_pltfrm_init() failed -517
[    3.267295] spmi spmi-0: PMIC arbiter version v5 (0x50000000)
[    3.275150] libphy: Fixed MDIO Bus: probed
[    3.277149] tun: Universal TUN/TAP device driver, 1.6
[    3.279551] thunder_xcv, ver 1.0
[    3.281391] thunder_bgx, ver 1.0
[    3.283205] nicpf, ver 1.0
[    3.285404] hclge is initializing
[    3.287184] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[    3.289021] hns3: Copyright (c) 2017 Huawei Corporation.
[    3.290889] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    3.292760] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    3.294661] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
[    3.296575] igb: Copyright (c) 2007-2014 Intel Corporation.
[    3.298538] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    3.300530] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    3.302751] sky2: driver version 1.30
[    3.305218] VFIO - User Level meta-driver version: 0.3
[    3.309986] dwc3 a600000.dwc3: Failed to get clk 'ref': -2
[    3.314256] dwc3 a800000.dwc3: Failed to get clk 'ref': -2
[    3.316885] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.318952] ehci-pci: EHCI PCI platform driver
[    3.321044] ehci-platform: EHCI generic platform driver
[    3.323226] ehci-orion: EHCI orion driver
[    3.325406] ehci-exynos: EHCI EXYNOS driver
[    3.327571] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.329715] ohci-pci: OHCI PCI platform driver
[    3.331883] ohci-platform: OHCI generic platform driver
[    3.334118] ohci-exynos: OHCI EXYNOS driver
[    3.336634] usbcore: registered new interface driver usb-storage
[    3.340938] i2c /dev entries driver
[    3.353479] sdhci: Secure Digital Host Controller Interface driver
[    3.354160] sdhci: Copyright(c) Pierre Ossman
[    3.354929] Synopsys Designware Multimedia Card Interface Driver
[    3.355835] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.357236] ledtrig-cpu: registered to indicate activity on CPUs
[    3.360197] hidraw: raw HID events driver (C) Jiri Kosina
[    3.361047] usbcore: registered new interface driver usbhid
[    3.361742] usbhid: USB HID core driver
[    3.363775] NET: Registered protocol family 17
[    3.364567] 9pnet: Installing 9P2000 support
[    3.365305] Key type dns_resolver registered
[    3.367290] registered taskstats version 1
[    3.368024] Loading compiled-in X.509 certificates
[    3.372070] qcom-qmp-phy 1d87000.phy: Registered Qcom-QMP phy
[    3.373180] qcom-qmp-phy 88e9000.phy: Registered Qcom-QMP phy
[    3.374176] qcom-qmp-phy 88eb000.phy: Registered Qcom-QMP phy
[    3.375074] qcom-qusb2-phy 88e2000.phy: Registered Qcom-QUSB2 phy
[    3.375966] qcom-qusb2-phy 88e3000.phy: Registered Qcom-QUSB2 phy
[    3.378510] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
[    3.379268] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
[    3.380007] ufshcd-qcom 1d84000.ufshc: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
[    3.382343] scsi host0: ufshcd
[    3.400901] dwc3 a600000.dwc3: Failed to get clk 'ref': -2
[    3.407313] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.408054] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.408882] xhci-hcd xhci-hcd.0.auto: hcc params 0x0230fe65 hci version 0x110 quirks 0x0000000002010010
[    3.409636] xhci-hcd xhci-hcd.0.auto: irq 49, io mem 0x0a600000
[    3.411097] hub 1-0:1.0: USB hub found
[    3.411834] hub 1-0:1.0: 1 port detected
[    3.412617] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.413319] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.414029] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    3.414743] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.415936] hub 2-0:1.0: USB hub found
[    3.416652] hub 2-0:1.0: 1 port detected
[    3.417716] dwc3 a800000.dwc3: Failed to get clk 'ref': -2
[    3.420010] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.420734] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    3.421567] xhci-hcd xhci-hcd.1.auto: hcc params 0x0230fe65 hci version 0x110 quirks 0x0000000002010010
[    3.422333] xhci-hcd xhci-hcd.1.auto: irq 50, io mem 0x0a800000
[    3.422511] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
[    3.423671] hub 3-0:1.0: USB hub found
[    3.427096] hub 3-0:1.0: 1 port detected
[    3.427924] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.428672] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    3.429418] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    3.430169] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.431445] hub 4-0:1.0: USB hub found
[    3.432197] hub 4-0:1.0: 1 port detected
[    3.433840] arm-smmu 5040000.iommu: ignoring dependency for device, assuming no driver
[    3.434755] PM: genpd: Not disabling unused power domains
[    3.436011] hctosys: unable to open rtc device (rtc0)
[    3.436931] psci_checker: PSCI checker started using 8 CPUs
[    3.437689] psci_checker: Starting hotplug tests
[    3.438444] psci_checker: Trying to turn off and on again all CPUs
[    3.441165] CPU0: shutdown
[    3.441946] psci: CPU0 killed.
[    3.444671] CPU1: shutdown
[    3.445440] psci: CPU1 killed.
[    3.447310] CPU2: shutdown
[    3.448096] psci: CPU2 killed.
[    3.452424] CPU3: shutdown
[    3.453167] psci: CPU3 killed.
[    3.455006] CPU4: shutdown
[    3.455745] psci: CPU4 killed.
[    3.457938] CPU5: shutdown
[    3.459010] psci: CPU5 killed.
[    3.461022] IRQ 5: no longer affine to CPU6
[    3.461152] CPU6: shutdown
[    3.462541] psci: CPU6 killed.
[    3.463795] Detected VIPT I-cache on CPU0
[    3.463826] GICv3: CPU0: found redistributor 0 region 0:0x0000000017a60000
[    3.463890] CPU0: Booted secondary processor 0x0000000000 [0x517f803c]
[    3.474744] Detected VIPT I-cache on CPU1
[    3.474767] GICv3: CPU1: found redistributor 100 region 0:0x0000000017a80000
[    3.474821] CPU1: Booted secondary processor 0x0000000100 [0x517f803c]
[    3.484649] Detected VIPT I-cache on CPU2
[    3.484668] GICv3: CPU2: found redistributor 200 region 0:0x0000000017aa0000
[    3.484714] CPU2: Booted secondary processor 0x0000000200 [0x517f803c]
[    3.495067] Detected VIPT I-cache on CPU3
[    3.495087] GICv3: CPU3: found redistributor 300 region 0:0x0000000017ac0000
[    3.495132] CPU3: Booted secondary processor 0x0000000300 [0x517f803c]
[    3.505427] Detected VIPT I-cache on CPU4
[    3.505443] GICv3: CPU4: found redistributor 400 region 0:0x0000000017ae0000
[    3.505484] CPU4: Booted secondary processor 0x0000000400 [0x516f802d]
[    3.508761] Detected VIPT I-cache on CPU5
[    3.508778] GICv3: CPU5: found redistributor 500 region 0:0x0000000017b00000
[    3.508818] CPU5: Booted secondary processor 0x0000000500 [0x516f802d]
[    3.512316] Detected VIPT I-cache on CPU6
[    3.512334] GICv3: CPU6: found redistributor 600 region 0:0x0000000017b20000
[    3.512376] CPU6: Booted secondary processor 0x0000000600 [0x516f802d]
[    3.515040] psci_checker: Trying to turn off and on again group 0 (CPUs 0-7)
[    3.517049] CPU0: shutdown
[    3.517838] psci: CPU0 killed.
[    3.519739] CPU1: shutdown
[    3.520497] psci: CPU1 killed.
[    3.521889] CPU2: shutdown
[    3.522645] psci: CPU2 killed.
[    3.523662] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[    3.527028] ufshcd-qcom 1d84000.ufshc: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[    3.529289] CPU3: shutdown
[    3.530070] psci: CPU3 killed.
[    3.531446] scsi 0:0:0:49488: Well-known LUN    SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.531809] CPU4: shutdown
[    3.532939] psci: CPU4 killed.
[    3.533857] scsi 0:0:0:49476: Well-known LUN    SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.534730] CPU5: shutdown
[    3.535515] psci: CPU5 killed.
[    3.536476] scsi 0:0:0:49456: Well-known LUN    SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.537235] IRQ 5: no longer affine to CPU6
[    3.537262] CPU6: shutdown
[    3.538742] psci: CPU6 killed.
[    3.540063] scsi 0:0:0:0: Direct-Access     SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.540282] Detected VIPT I-cache on CPU0
[    3.540812] GICv3: CPU0: found redistributor 0 region 0:0x0000000017a60000
[    3.540865] CPU0: Booted secondary processor 0x0000000000 [0x517f803c]
[    3.552037] scsi 0:0:0:1: Direct-Access     SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.552184] Detected VIPT I-cache on CPU1
[    3.552810] GICv3: CPU1: found redistributor 100 region 0:0x0000000017a80000
[    3.552861] CPU1: Booted secondary processor 0x0000000100 [0x517f803c]
[    3.563148] scsi 0:0:0:2: Direct-Access     SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.564158] Detected VIPT I-cache on CPU2
[    3.564177] GICv3: CPU2: found redistributor 200 region 0:0x0000000017aa0000
[    3.564223] CPU2: Booted secondary processor 0x0000000200 [0x517f803c]
[    3.575328] scsi 0:0:0:3: Direct-Access     SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.575382] Detected VIPT I-cache on CPU3
[    3.578897] GICv3: CPU3: found redistributor 300 region 0:0x0000000017ac0000
[    3.578943] CPU3: Booted secondary processor 0x0000000300 [0x517f803c]
[    3.590462] scsi 0:0:0:4: Direct-Access     SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.591688] Detected VIPT I-cache on CPU4
[    3.591705] GICv3: CPU4: found redistributor 400 region 0:0x0000000017ae0000
[    3.591748] CPU4: Booted secondary processor 0x0000000400 [0x516f802d]
[    3.595339] scsi 0:0:0:5: Direct-Access     SAMSUNG  KLUDG4U1EA-B0C1  0500 PQ: 0 ANSI: 6
[    3.595385] Detected VIPT I-cache on CPU5
[    3.599208] GICv3: CPU5: found redistributor 500 region 0:0x0000000017b00000
[    3.599248] CPU5: Booted secondary processor 0x0000000500 [0x516f802d]
[    3.599979] sd 0:0:0:0: Power-on or device reset occurred
[    3.603803] sd 0:0:0:1: Power-on or device reset occurred
[    3.604725] sd 0:0:0:2: Power-on or device reset occurred
[    3.605621] sd 0:0:0:3: Power-on or device reset occurred
[    3.606515] sd 0:0:0:4: Power-on or device reset occurred
[    3.607384] sd 0:0:0:5: Power-on or device reset occurred
[    3.608555] Detected VIPT I-cache on CPU6
[    3.608574] GICv3: CPU6: found redistributor 600 region 0:0x0000000017b20000
[    3.608616] CPU6: Booted secondary processor 0x0000000600 [0x516f802d]
[    3.608798] sd 0:0:0:5: [sdf] 393216 4096-byte logical blocks: (1.61 GB/1.50 GiB)
[    3.608831] sd 0:0:0:4: [sde] 1048576 4096-byte logical blocks: (4.29 GB/4.00 GiB)
[    3.608916] sd 0:0:0:2: [sdc] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
[    3.609648] sd 0:0:0:4: [sde] Write Protect is off
[    3.609781] sd 0:0:0:2: [sdc] Write Protect is off
[    3.609783] psci_checker: Hotplug tests passed OK
[    3.609786] psci_checker: Starting suspend tests (10 cycles per state)
[    3.609787] sd 0:0:0:2: [sdc] Mode Sense: 00 32 00 10
[    3.610521] sd 0:0:0:3: [sdd] 32768 4096-byte logical blocks: (134 MB/128 MiB)
[    3.610529] sd 0:0:0:0: [sda] 29765632 4096-byte logical blocks: (122 GB/114 GiB)
[    3.610585] sd 0:0:0:5: [sdf] Write Protect is off
[    3.610586] sd 0:0:0:5: [sdf] Mode Sense: 00 32 00 10
[    3.610597] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    3.610610] sd 0:0:0:0: [sda] Write Protect is off
[    3.610614] sd 0:0:0:0: [sda] Mode Sense: 00 32 00 10
[    3.610629] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
[    3.610645] sd 0:0:0:2: [sdc] Optimal transfer size 8192 bytes
[    3.610689] sd 0:0:0:1: [sdb] Write Protect is off
[    3.610690] sd 0:0:0:5: [sdf] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    3.610692] sd 0:0:0:1: [sdb] Mode Sense: 00 32 00 10
[    3.610718] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    3.610721] sd 0:0:0:5: [sdf] Optimal transfer size 8192 bytes
[    3.610765] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes
[    3.610801] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    3.610845] sd 0:0:0:1: [sdb] Optimal transfer size 8192 bytes
[    3.611769] sd 0:0:0:4: [sde] Mode Sense: 00 32 00 10
[    3.612090] psci_checker: CPU 5 entering suspend cycles, states 1 through 3
[    3.612092] psci_checker: CPU 6 entering suspend cycles, states 1 through 3
[    3.612094] psci_checker: CPU 1 entering suspend cycles, states 1 through 3
[    3.612096] psci_checker: CPU 2 entering suspend cycles, states 1 through 3
[    3.612097] psci_checker: CPU 7 entering suspend cycles, states 1 through 3
[    3.612099] psci_checker: CPU 3 entering suspend cycles, states 1 through 3
[    3.612102] psci_checker: CPU 0 entering suspend cycles, states 1 through 3
[    3.612635] psci_checker: CPU 4 entering suspend cycles, states 1 through 3
[    3.732084]  sdf: sdf2 sdf3 sdf4 sdf5
[    3.732351]  sdc: sdc1 sdc2
[    3.732501]  sdb: sdb1 sdb2
[    3.732502] sd 0:0:0:4: [sde] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    3.732612] sd 0:0:0:4: [sde] Optimal transfer size 8192 bytes
[    3.733429]  sda: sda1 sda2 sda3 sda4 sda5
[    3.738549] sd 0:0:0:3: [sdd] Write Protect is off
[    3.739116] random: fast init done
[    3.741355] sd 0:0:0:3: [sdd] Mode Sense: 00 32 00 10
[    3.742049] sd 0:0:0:5: [sdf] Attached SCSI disk
[    3.742092] sd 0:0:0:1: [sdb] Attached SCSI disk
[    3.742162]  sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27
[    3.743997] sd 0:0:0:4: [sde] Attached SCSI disk
[    3.744866] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    3.755612] psci_checker: CPU 0 suspend test results: success 30, shallow states 0, errors 0
[    3.755915] sd 0:0:0:2: [sdc] Attached SCSI disk
[    3.756115] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.756520] sd 0:0:0:3: [sdd] Optimal transfer size 8192 bytes
[    3.759333] psci_checker: CPU 1 suspend test results: success 30, shallow states 0, errors 0
[    3.761368]  sdd: sdd2 sdd3
[    3.762754] psci_checker: CPU 2 suspend test results: success 30, shallow states 0, errors 0
[    3.764198] sd 0:0:0:3: [sdd] Attached SCSI disk
[    3.766193] psci_checker: CPU 3 suspend test results: success 30, shallow states 0, errors 0
[    3.775768] psci_checker: CPU 4 suspend test results: success 30, shallow states 0, errors 0
[    3.776550] psci_checker: CPU 5 suspend test results: success 30, shallow states 0, errors 0
[    3.777331] psci_checker: CPU 6 suspend test results: success 30, shallow states 0, errors 0
[    3.778090] psci_checker: CPU 7 suspend test results: success 30, shallow states 0, errors 0
[    3.778815] psci_checker: Suspend tests passed OK
[    3.779519] psci_checker: PSCI checker completed
[    3.780289] clk: Not disabling unused clocks
[    3.780976] ALSA device list:
[    3.781659]   No soundcards found.
[    3.783254] Freeing unused kernel memory: 5440K
[    3.800205] Run /init as init process
[    3.859519] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    4.018227] systemd-udevd[541]: starting version 3.2.7
[    4.019450] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    4.020472] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    4.021452] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    4.023477] udevd[542]: starting eudev-3.2.7
[    4.070583] hub 3-1:1.0: USB hub found
[    4.073700] hub 3-1:1.0: 3 ports detected
[    4.106023] i2c_hid 3-0015: 3-0015 supply vdd not found, using dummy regulator
[    4.106784] i2c_hid 3-0015: 3-0015 supply vddl not found, using dummy regulator
[    4.108241] i2c_hid 3-002c: 3-002c supply vdd not found, using dummy regulator
[    4.108981] i2c_hid 3-002c: 3-002c supply vddl not found, using dummy regulator
[    4.135815] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[    4.137451] input: hid-over-i2c 06CB:CD3E Mouse as /devices/platform/soc/8c0000.geniqup/88c000.i2c/i2c-3/3-002c/0018:06CB:CD3E.0001/input/input0
[    4.140152] input: hid-over-i2c 06CB:CD3E Touchpad as /devices/platform/soc/8c0000.geniqup/88c000.i2c/i2c-3/3-002c/0018:06CB:CD3E.0001/input/input1
[    4.141021] hid-generic 0018:06CB:CD3E.0001: input,hidraw0: I2C HID v1.00 Mouse [hid-over-i2c 06CB:CD3E] on 3-002c
[    4.142242] i2c_hid 5-0010: 5-0010 supply vdd not found, using dummy regulator
[    4.143039] i2c_hid 5-0010: 5-0010 supply vddl not found, using dummy regulator
[    4.168802] power_supply hid-0018:04F3:279F.0002-battery: hwmon: 'hid-0018:04F3:279F.0002-battery' is not a valid name attribute, please fix
[    4.169684] input: hid-over-i2c 04F3:279F Touchscreen as /devices/platform/soc/8c0000.geniqup/894000.i2c/i2c-5/5-0010/0018:04F3:279F.0002/input/input3
[    4.170576] input: hid-over-i2c 04F3:279F as /devices/platform/soc/8c0000.geniqup/894000.i2c/i2c-5/5-0010/0018:04F3:279F.0002/input/input4
[    4.171788] input: hid-over-i2c 04F3:279F as /devices/platform/soc/8c0000.geniqup/894000.i2c/i2c-5/5-0010/0018:04F3:279F.0002/input/input5
[    4.172854] input: hid-over-i2c 04F3:279F as /devices/platform/soc/8c0000.geniqup/894000.i2c/i2c-5/5-0010/0018:04F3:279F.0002/input/input6
[    4.173759] hid-generic 0018:04F3:279F.0002: input,hidraw1: I2C HID v1.00 Device [hid-over-i2c 04F3:279F] on 5-0010
[    4.174855] i2c_hid 11-005c: 11-005c supply vdd not found, using dummy regulator
[    4.175813] i2c_hid 11-005c: 11-005c supply vddl not found, using dummy regulator
[    4.182491] hub 4-1:1.0: USB hub found
[    4.186468] hub 4-1:1.0: 2 ports detected
[    4.228925] input: hid-over-i2c 6243:0001 Keyboard as /devices/platform/soc/ac0000.geniqup/a8c000.i2c/i2c-11/11-005c/0018:6243:0001.0003/input/input9
[    4.230222] input: hid-over-i2c 6243:0001 Consumer Control as /devices/platform/soc/ac0000.geniqup/a8c000.i2c/i2c-11/11-005c/0018:6243:0001.0003/input/input10
[    4.231427] input: hid-over-i2c 6243:0001 Wireless Radio Control as /devices/platform/soc/ac0000.geniqup/a8c000.i2c/i2c-11/11-005c/0018:6243:0001.0003/input/input12
[    4.232811] input: hid-over-i2c 6243:0001 as /devices/platform/soc/ac0000.geniqup/a8c000.i2c/i2c-11/11-005c/0018:6243:0001.0003/input/input13
[    4.234649] hid-generic 0018:6243:0001.0003: input,hidraw2: I2C HID v1.00 Keyboard [hid-over-i2c 6243:0001] on 11-005c
[    4.288669] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[    4.353910] dracut: Checking ext4: /dev/disk/by-partuuid/637cbe98-d2db-4ae4-b513-022b30fdcd8f
[    4.358568] dracut: issuing e2fsck -a  /dev/disk/by-partuuid/637cbe98-d2db-4ae4-b513-022b30fdcd8f
[    4.372998] dracut: Linux: clean, 261082/5120000 files, 4579241/20480000 blocks
[    4.381403] dracut: Mounting /dev/disk/by-partuuid/637cbe98-d2db-4ae4-b513-022b30fdcd8f with -o defaults,ro,rw
[    4.391138] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[    4.417473] dracut: Mounted root filesystem /dev/sda5
[    4.451753] usb 3-1.2: new high-speed USB device number 3 using xhci-hcd
[    4.504872] dracut: Switching root
[    4.647064] hub 3-1.2:1.0: USB hub found
[    4.649546] hub 3-1.2:1.0: 4 ports detected
[    4.677352] fuse: init (API version 7.31)
[    4.678805] usb 4-1.2: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[    4.689048] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: [email protected]
[    4.722939] udevd[773]: starting version 3.2.7
[    4.741617] udevd[774]: starting eudev-3.2.7
[    4.747500] hub 4-1.2:1.0: USB hub found
[    4.750167] hub 4-1.2:1.0: 4 ports detected
[    4.794933] EFI Variables Facility v0.08 2004-May-17
[    4.796564] efivars: get_next_variable: status=8000000000000003
[    4.799239] pstore: Using crash dump compression: deflate
[    4.800858] pstore: Registered efi as persistent store backend
[    4.815476] usb 3-1.3: new high-speed USB device number 4 using xhci-hcd
[    4.820291] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    4.824900] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.001564] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.002666] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.006896] mc: Linux media interface: v0.10
[    5.012684] videodev: Linux video capture interface: v2.00
[    5.022631] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.022993] uvcvideo: Found UVC 1.00 device Integrated Camera (5986:2115)
[    5.023750] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.024724] usb 3-1.2.1: new full-speed USB device number 5 using xhci-hcd
[    5.051302] uvcvideo 3-1.3:1.0: Entity type for entity Extension 4 was not initialized!
[    5.052324] uvcvideo 3-1.3:1.0: Entity type for entity Extension 3 was not initialized!
[    5.053303] uvcvideo 3-1.3:1.0: Entity type for entity Processing 2 was not initialized!
[    5.054264] uvcvideo 3-1.3:1.0: Entity type for entity Camera 1 was not initialized!
[    5.055551] input: Integrated Camera: Integrated C as /devices/platform/soc/a8f8800.usb/a800000.dwc3/xhci-hcd.1.auto/usb3/3-1/3-1.3/3-1.3:1.0/input/input14
[    5.056844] usbcore: registered new interface driver uvcvideo
[    5.057829] USB Video Class driver (1.1.1)
[    5.059578] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.060607] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.131616] usb 3-1.2.1: not running at top speed; connect to a high speed hub
[    5.141216] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.142298] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.216858] usb 4-1.2.3: new SuperSpeed Gen 1 USB device number 4 using xhci-hcd
[    5.273719] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.274852] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.280281] usbcore: registered new interface driver r8152
[    5.284390] usbcore: registered new interface driver cdc_ether
[    5.315632] usb 3-1.2.2: new full-speed USB device number 6 using xhci-hcd
[    5.511125] usb 4-1.2.4: new SuperSpeed Gen 1 USB device number 5 using xhci-hcd
[    5.516878] input: C-Media Electronics Inc. USB Advanced Audio Device as /devices/platform/soc/a8f8800.usb/a800000.dwc3/xhci-hcd.1.auto/usb3/3-1/3-1.2/3-1.2.2/3-1.2.2:1.3/0003:0D8C:0022.0004/input/input15
[    5.580009] hid-generic 0003:0D8C:0022.0004: input,hidraw3: USB HID v1.11 Device [C-Media Electronics Inc. USB Advanced Audio Device] on usb-xhci-hcd.1.auto-1.2.2/input3
[    5.581085] hub 4-1.2.4:1.0: USB hub found
[    5.583022] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.584054] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.585027] hub 4-1.2.4:1.0: 4 ports detected
[    5.591526] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.592523] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.639212] usb 4-1.2.3: reset SuperSpeed Gen 1 USB device number 4 using xhci-hcd
[    5.739049] r8152 4-1.2.3:1.0 eth0: v1.09.10
[    5.740849] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.741848] remoteproc remoteproc0: releasing 4080000.remoteproc
[    5.743451] usb 3-1.2.4: new high-speed USB device number 7 using xhci-hcd
[    5.928679] hub 3-1.2.4:1.0: USB hub found
[    5.931444] hub 3-1.2.4:1.0: 4 ports detected
[    5.998301] qcom-q6v5-mss 4080000.remoteproc: failed to acquire mss restart
[    5.999328] remoteproc remoteproc0: releasing 4080000.remoteproc
[    6.051954] EXT4-fs (sda5): re-mounted. Opts: stripe=2
[    6.109188] random: crng init done
[    6.113261] random: 7 urandom warning(s) missed due to ratelimiting
[    6.254062] EXT4-fs (sda5): re-mounted. Opts: stripe=2
[    7.402530] udevd[869]: starting version 3.2.7
[    7.421277] udevd[869]: starting eudev-3.2.7
[    7.433829] 8021q: 802.1Q VLAN Support v1.8
[    7.442778] NET: Registered protocol family 10
[    7.444500] Segment Routing with IPv6
[    7.455797] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    7.466162] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    7.472279] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    7.475784] cfg80211: failed to load regulatory.db
[    8.942045] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.943125] r8152 4-1.2.3:1.0 eth0: carrier on
[   34.296048] smps2: disabling
[   34.296884] smps4: disabling
[   34.297695] smps7: disabling
[   34.298432] ldo3: disabling
[   34.299156] ldo5: disabling
[   34.299920] ldo6: disabling
[   34.300969] ldo7: disabling
[   34.301786] ldo8: disabling
[   34.302464] ldo9: disabling
[   34.303128] ldo10: disabling
[   34.303806] ldo11: disabling
[   34.304454] ldo13: disabling
[   34.305117] ldo14: disabling
[   34.305765] ldo15: disabling
[   34.306370] ldo16: disabling
[   34.306971] ldo17: disabling
[   34.307883] ldo18: disabling
[   34.308489] ldo19: disabling
[   34.309404] ldo21: disabling
[   34.309962] ldo22: disabling
[   34.310523] ldo23: disabling
[   34.311061] ldo25: disabling
[   34.311948] ldo28: disabling
[   34.312494] lvs1: disabling
[   34.313044] lvs2: disabling