gistfile1.txt

mesg
<6>[    0.000000] Booting Linux on physical CPU 0
<6>[    0.000000] Initializing cgroup subsys cpu
<5>[    0.000000] Linux version 3.4.0-gcb7e7de (tassadar@nymeria) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #4 SMP PREEMPT Wed Sep 4 18:22:32 CEST 2013
<4>[    0.000000] CPU: ARMv7 Processor [511f06f0] revision 0 (ARMv7), cr=10c5387d
<4>[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
<4>[    0.000000] Machine: QCT APQ8064 FLO
<2>[    0.000000] Truncating memory at 0x90000000 to fit in 32-bit physical address space
<6>[    0.000000] cma: CMA: reserved 80 MiB at a0000000
<6>[    0.000000] memory pool 3 (start 0xfe900000 size 1600000) initialized
<6>[    0.000000] Initialized persistent memory from 88d00000-88dfffff
<6>[    0.000000] cma: CMA: reserved 16 MiB at afc00000
<4>[    0.000000] Memory policy: ECC disabled, Data cache writealloc
<6>[    0.000000] socinfo_init: v7, id=172, ver=2.0, raw_id=2289, raw_ver=2289, hw_plat=8, hw_plat_ver=65536
<6>[    0.000000]  accessory_chip=0, hw_plat_subtype=0, pmic_model=18, pmic_die_revision=4
<7>[    0.000000] On node 0 totalpages: 505855
<7>[    0.000000] free_area_init_node: node 0, pgdat c1144700, node_mem_map c236b000
<7>[    0.000000]   Normal zone: 1556 pages used for memmap
<7>[    0.000000]   Normal zone: 0 pages reserved
<7>[    0.000000]   Normal zone: 185324 pages, LIFO batch:31
<7>[    0.000000]   HighMem zone: 2536 pages used for memmap
<7>[    0.000000]   HighMem zone: 316439 pages, LIFO batch:31
<6>[    0.000000] allocating 44236800 bytes at c3371000 (83571000 physical) for fb
<6>[    0.000000] PERCPU: Embedded 7 pages/cpu @c5da4000 s15808 r0 d12864 u32768
<7>[    0.000000] pcpu-alloc: s15808 r0 d12864 u32768 alloc=8*4096
<7>[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
<4>[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 501763
<5>[    0.000000] Kernel command line: androidboot.hardware=flo user_debug=31 msm_rtb.filter=0x3F ehci-hcd.park=3 androidboot.emmc=true androidboot.serialno=0875369a bootreason=Reboot fuse_info=Y ddr_vendor=hynix androidboot.baseband=apq asustek.hw_rev=rev_e androidboot.bootloader=FLO-04.02
<6>[    0.000000] HW Revision: ASUSTek input rev_e 
<6>[    0.000000] HW Revision: ASUSTek matched rev_e 
<6>[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[    0.000000] allocated 4190200 bytes of page_cgroup
<6>[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
<6>[    0.000000] Memory: 140MB 58MB 4MB 7MB 254MB 80MB 1432MB 0MB = 1975MB total
<5>[    0.000000] Memory: 1836092k/1836092k available, 212928k reserved, 1275900K highmem
<5>[    0.000000] Virtual kernel memory layout:
<5>[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
<5>[    0.000000]     timers  : 0xfffef000 - 0xffff0000   (   4 kB)
<5>[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
<5>[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
<5>[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
<5>[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
<5>[    0.000000]       .text : 0xc0008000 - 0xc0e9f440   (14942 kB)
<5>[    0.000000]       .init : 0xc0f00000 - 0xc101ddc0   (1144 kB)
<5>[    0.000000]       .data : 0xc101e000 - 0xc11709a0   (1355 kB)
<5>[    0.000000]        .bss : 0xc11709c4 - 0xc143db14   (2869 kB)
<6>[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
<6>[    0.000000] Preemptible hierarchical RCU implementation.
<6>[    0.000000] NR_IRQS:1177
<6>[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
<6>[    0.000000] Switching to timer-based delay loop
<6>[    0.000000] Console: colour dummy device 80x30
<6>[    0.000000] console [tty0] enabled
<6>[    0.000671] Calibrating delay loop (skipped), value calculated using timer frequency.. 13.50 BogoMIPS (lpj=67500)
<6>[    0.000701] pid_max: default: 32768 minimum: 301
<6>[    0.000976] Security Framework initialized
<6>[    0.001037] SELinux:  Initializing.
<7>[    0.001098] SELinux:  Starting in permissive mode
<6>[    0.001251] Mount-cache hash table entries: 512
<6>[    0.002716] Initializing cgroup subsys debug
<6>[    0.002746] Initializing cgroup subsys cpuacct
<6>[    0.002746] Initializing cgroup subsys memory
<6>[    0.002838] Initializing cgroup subsys freezer
<6>[    0.002899] CPU: Testing write buffer coherency: ok
<6>[    0.003265] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
<6>[    0.003295] hw perfevents: enabled with ARMv7 Krait PMU driver, 5 counters available
<6>[    0.003417] Setting up static identity map for 0x80c08320 - 0x80c083a8
<6>[    0.006011] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
<6>[    0.008850] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
<6>[    0.011108] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
<6>[    0.011260] Brought up 4 CPUs
<6>[    0.011322] SMP: Total of 4 processors activated (54.00 BogoMIPS).
<6>[    0.029876] dummy: 
<6>[    0.035919] NET: Registered protocol family 16
<6>[    0.036895] DMA: preallocated 256 KiB pool for atomic coherent allocations
<3>[    0.037109] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
<5>[    0.039825] MIDR      = 0x511f06f0
<6>[    0.039855] meminfo_init: smem ram ptable found: ver: 0 len: 5
<6>[    0.039886] Found 1 memory banks grouped into 8 memory regions
<6>[    0.040130] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio
<6>[    0.041290] socinfo_init: v7, id=172, ver=2.0, raw_id=2289, raw_ver=2289, hw_plat=8, hw_plat_ver=65536
<6>[    0.041320]  accessory_chip=0, hw_plat_subtype=0, pmic_model=18, pmic_die_revision=4
<6>[    0.041442] msm_rpm_init: RPM firmware 3.0.16842936
<3>[    0.063079] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063110] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063110] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063140] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063171] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063171] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063201] msm_rpm_get_status(): Status id 433 not defined for target
<3>[    0.063232] msm_rpm_get_status(): Status id 433 not defined for target
<6>[    0.082092] ASUSTek: Bypassing PCB_ID3
<6>[    0.082153] ASUSTek: PCBID=043
<6>[    0.083190] gpio_vreg_probe: id=203, name=ext_mpp8, gpio=203, gpio_label=ext_mpp8_en
<6>[    0.083435] pm8921_probe: PMIC revision 1: F4
<6>[    0.083465] pm8921_probe: PMIC revision 2: 06
<6>[    0.083465] pm8921_probe: PMIC version: PM8921 rev 3.0
<6>[    0.083496] pm8921_probe: PMIC Restart Reason: Triggered from KPD (power key press)
<6>[    0.084777] gpiochip_add: registered GPIOs 152 to 195 on device: pm-gpio
<6>[    0.085296] pm_gpio_probe: OK: base=152, ngpio=44
<6>[    0.085601] gpiochip_add: registered GPIOs 196 to 207 on device: pm8xxx-mpp
<6>[    0.085693] pm8xxx_mpp_probe: OK: base=196, ngpio=12
<6>[    0.087554] pm8821_probe: PMIC revision 1: PM8821 rev F3
<6>[    0.087585] pm8821_probe: PMIC revision 2: PM8821 rev 0B
<6>[    0.087615] pm8821_probe: PMIC version: PM8821 ver 2.1
<6>[    0.088256] gpiochip_add: registered GPIOs 208 to 211 on device: pm8xxx-mpp
<6>[    0.088287] pm8xxx_mpp_probe: OK: base=208, ngpio=4
<3>[    0.088623] gpio_vreg_probe: gpio_label required.
<4>[    0.088653] msm-gpio-regulator: probe of msm-gpio-regulator.174 failed with error -22
<6>[    0.089874] saw_probe: id=0, name=8921_s5
<6>[    0.090240] saw_probe: id=1, name=8921_s6
<6>[    0.090667] saw_probe: id=2, name=8821_s0
<6>[    0.091033] saw_probe: id=3, name=8821_s1
<3>[    0.099182] Sensors:DSPS: initial dsps.
<4>[    0.100158] [ELAN] Touch dirver register
<6>[    0.100555] persistent_ram: found existing buffer, size 225700, start 60473
<6>[    0.752746] console [ram-1] enabled
<4>[    0.753448] apq8064_init_fb: lcd_type=0
<6>[    0.753662] apq8064_init_fb: register mipi_JDI_panel_device
<3>[    0.755065] msm_gpiomux_install: write failure: -22
<3>[    0.755187] msm_gpiomux_install: write failure: -22
<3>[    0.755340] msm_gpiomux_install: write failure: -22
<3>[    0.755462] msm_gpiomux_install: write failure: -22
<3>[    0.755554] msm_gpiomux_install: write failure: -22
<3>[    0.755706] msm_gpiomux_install: write failure: -22
<6>[    0.756652] Registering gpio keys
<6>[    0.756805] Reconfigure VOL_UP(GPIO155) and VOL_DOWN(GPIO189) with PMIC
<4>[    0.757049] 8921_l17: Failed to create debugfs directory
<6>[    0.757934] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
<6>[    0.758026] hw-breakpoint: maximum watchpoint size is 8 bytes.
<6>[    0.763458] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20
<6>[    0.763549] sps:BAM 0x12244000 is registered.
<6>[    0.764221] sps:sps is ready.
<6>[    0.796417] bio: create slab <bio-0> at 0
<6>[    0.797180] vgaarb: loaded
<6>[    0.797546] ION heap vmalloc created
<6>[    0.797698] ION heap mm created at a0000000 with size 5000000
<6>[    0.797882] ION heap mm_fw created at 9fe00000 with size 1e0000
<6>[    0.798004] ION heap mfc created at a5000000 with size 2000
<6>[    0.798187] ION heap iommu created
<6>[    0.798339] ION heap qsecom created at fe909000 with size 780000
<6>[    0.798461] ION heap audio created at ff089000 with size 4cf000
<5>[    0.799835] pm8xxx_pwm_probe: OK
<5>[    0.800598] SCSI subsystem initialized
<6>[    0.801055] sps:BAM 0x28084000 enabled: ver:0x12, number of pipes:31
<6>[    0.801208] sps:BAM 0x28084000 is registered.
<6>[    0.802337] usbcore: registered new interface driver usbfs
<6>[    0.802673] usbcore: registered new interface driver hub
<6>[    0.802947] usbcore: registered new device driver usb
<6>[    0.803253] Linux media interface: v0.10
<6>[    0.803436] Linux video capture interface: v2.00
<7>[    0.804016] Registered led device: white
<6>[    0.804779] apq8064_pm8921_pwm_init+
<6>[    0.804962] apq8064_pm8921_pwm_init-
<6>[    0.805786] msm_iommu_dev: device vpe mapped at f0400000, with 2 ctx banks
<6>[    0.806091] msm_iommu_dev: device mdp0 mapped at f0600000, with 2 ctx banks
<6>[    0.806304] msm_iommu_dev: device mdp1 mapped at f0800000, with 2 ctx banks
<6>[    0.806610] msm_iommu_dev: device rot mapped at f0a00000, with 2 ctx banks
<6>[    0.806884] msm_iommu_dev: device ijpeg mapped at f0c00000, with 2 ctx banks
<6>[    0.807128] msm_iommu_dev: device vfe mapped at f0e00000, with 2 ctx banks
<6>[    0.807403] msm_iommu_dev: device vcodec_a mapped at f1000000, with 2 ctx banks
<6>[    0.807708] msm_iommu_dev: device vcodec_b mapped at f1200000, with 2 ctx banks
<6>[    0.807952] msm_iommu_dev: device gfx3d mapped at f1400000, with 3 ctx banks
<6>[    0.808227] msm_iommu_dev: device jpegd mapped at f1600000, with 2 ctx banks
<6>[    0.808471] msm_iommu_dev: device gfx3d1 mapped at f1800000, with 3 ctx banks
<6>[    0.808746] msm_iommu_dev: device vcap mapped at f1a00000, with 2 ctx banks
<6>[    0.809356] msm_iommu_ctx msm_iommu_ctx.2: context vpe_src using bank 0
<6>[    0.809570] msm_iommu_ctx msm_iommu_ctx.3: context vpe_dst using bank 1
<6>[    0.809906] msm_iommu_ctx msm_iommu_ctx.4: context mdp_port0_cb0 using bank 0
<6>[    0.810180] msm_iommu_ctx msm_iommu_ctx.5: context mdp_port0_cb1 using bank 1
<6>[    0.810516] msm_iommu_ctx msm_iommu_ctx.6: context mdp_port1_cb0 using bank 0
<6>[    0.810852] msm_iommu_ctx msm_iommu_ctx.7: context mdp_port1_cb1 using bank 1
<6>[    0.811126] msm_iommu_ctx msm_iommu_ctx.8: context rot_src using bank 0
<6>[    0.811431] msm_iommu_ctx msm_iommu_ctx.9: context rot_dst using bank 1
<6>[    0.811737] msm_iommu_ctx msm_iommu_ctx.10: context ijpeg_src using bank 0
<6>[    0.811981] msm_iommu_ctx msm_iommu_ctx.11: context ijpeg_dst using bank 1
<6>[    0.812316] msm_iommu_ctx msm_iommu_ctx.12: context vfe_imgwr using bank 0
<6>[    0.812561] msm_iommu_ctx msm_iommu_ctx.13: context vfe_misc using bank 1
<6>[    0.812957] msm_iommu_ctx msm_iommu_ctx.14: context vcodec_a_stream using bank 0
<6>[    0.813293] msm_iommu_ctx msm_iommu_ctx.15: context vcodec_a_mm1 using bank 1
<6>[    0.813598] msm_iommu_ctx msm_iommu_ctx.16: context vcodec_b_mm2 using bank 0
<6>[    0.813995] msm_iommu_ctx msm_iommu_ctx.17: context gfx3d_user using bank 0
<6>[    0.814392] msm_iommu_ctx msm_iommu_ctx.18: context gfx3d_priv using bank 1
<6>[    0.814636] msm_iommu_ctx msm_iommu_ctx.0: context jpegd_src using bank 0
<6>[    0.814941] msm_iommu_ctx msm_iommu_ctx.1: context jpegd_dst using bank 1
<6>[    0.815277] msm_iommu_ctx msm_iommu_ctx.19: context gfx3d1_user using bank 0
<6>[    0.815673] msm_iommu_ctx msm_iommu_ctx.20: context gfx3d1_priv using bank 1
<6>[    0.816009] msm_iommu_ctx msm_iommu_ctx.21: context vcap_vc using bank 0
<6>[    0.816253] msm_iommu_ctx msm_iommu_ctx.22: context vcap_vp using bank 1
<6>[    0.816528] Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>[    0.817260] Bluetooth: Core ver 2.16
<6>[    0.817474] NET: Registered protocol family 31
<6>[    0.817565] Bluetooth: HCI device and connection manager initialized
<6>[    0.817749] Bluetooth: HCI socket layer initialized
<6>[    0.817840] Bluetooth: L2CAP socket layer initialized
<6>[    0.818206] Bluetooth: SCO socket layer initialized
<6>[    0.818695] cfg80211: Calling CRDA to update world regulatory domain
<6>[    0.818847] cfg80211: World regulatory domain updated:
<6>[    0.819000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[    0.819183] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[    0.819274] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[    0.819458] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[    0.819641] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[    0.819732] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[    0.820892] Switching to clocksource gp_timer
<6>[    0.860412] NET: Registered protocol family 2
<6>[    0.860870] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[    0.861602] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>[    0.862915] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>[    0.863739] TCP: Hash tables configured (established 131072 bind 65536)
<6>[    0.863830] TCP: reno registered
<6>[    0.864013] UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>[    0.864135] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>[    0.864715] NET: Registered protocol family 1
<6>[    0.865264] RPC: Registered named UNIX socket transport module.
<6>[    0.865447] RPC: Registered udp transport module.
<6>[    0.865539] RPC: Registered tcp transport module.
<6>[    0.865661] RPC: Registered tcp NFSv4.1 backchannel transport module.
<7>[    0.865814] PCI: CLS 0 bytes, default 64
<6>[    0.866149] Trying to unpack rootfs image as initramfs...
<6>[    1.104919] Freeing initrd memory: 3480K
<6>[    1.106719] Detected 9 counters on the L2CC PMU.
<6>[    1.108459] pil_qdsp6v4 pil_qdsp6v4.0: using secure boot
<6>[    1.109924] pil_riva pil_riva: using secure boot
<6>[    1.112365] pil_dsps pil_dsps: using secure boot
<6>[    1.113586] pil_gss pil_gss: using secure boot
<3>[    1.121429] smd_channel_probe_worker: allocation table not initialized
<6>[    1.124603] msm_dsps driver version 4.03.
<6>[    1.126953] NET: Registered protocol family 27
<1>[    1.130950] dma_test_init, minor number 97
<6>[    1.131561] lpass_fatal_init: lpass SSR driver init'ed.
<6>[    1.131896] wcnss_8960: module initialized
<6>[    1.132476] gss_8064_init: gss fatal driver init'ed.
<6>[    1.133453] acpuclk-8064 acpuclk-8064: SPEED BIN: 14
<6>[    1.133605] acpuclk-8064 acpuclk-8064: ACPU PVS: 2
<6>[    1.136260] acpuclk-8064 acpuclk-8064: CPU0: 12 frequencies supported
<6>[    1.136383] acpuclk-8064 acpuclk-8064: CPU1: 12 frequencies supported
<6>[    1.136566] acpuclk-8064 acpuclk-8064: CPU2: 12 frequencies supported
<6>[    1.136657] acpuclk-8064 acpuclk-8064: CPU3: 12 frequencies supported
<5>[    1.139373] msm_rpm_log_probe: OK
<6>[    1.142669] usbcore: registered new interface driver hsic_sysmon
<6>[    1.146331] audit: initializing netlink socket (disabled)
<5>[    1.146453] type=2000 audit(1.120:1): initialized
<4>[    1.147399] highmem bounce pool size: 64 pages
<5>[    1.152496] NFS: Registering the id_resolver key type
<6>[    1.153350] fuse init (API version 7.18)
<6>[    1.153594] msgmni has been set to 1260
<7>[    1.153717] SELinux:  Registering netfilter hooks
<6>[    1.155578] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
<6>[    1.155700] io scheduler noop registered
<6>[    1.155761] io scheduler deadline registered
<6>[    1.155883] io scheduler row registered
<6>[    1.156066] io scheduler cfq registered (default)
<6>[    1.156127] io scheduler test-iosched registered
<6>[    1.157928] mipi_dsi base phy_addr = 0x4700000 virt = 0xf1c00000
<6>[    1.158020] mmss_sfpb  base phy_addr = 0x5700000,virt = 0xf01f2000
<6>[    1.158233] mipi_JDI_1080P_pt_init+
<6>[    1.158416] mipi_JDI_lcd_probe+
<6>[    1.158477] mipi_JDI_lcd_probe, hw_revision=0
<6>[    1.158599] mipi_JDI_lcd_probe, lcd_pwm_type=0
<6>[    1.158843] mipi_JDI_lcd_probe+
<6>[    1.158905] mipi_JDI_lcd_probe, hw_revision=0
<6>[    1.159027] mipi_JDI_lcd_probe, lcd_pwm_type=0
<6>[    1.159088] setting pdata->panel_info.fb_num to 3. type: 9
<3>[    1.159301] cont_splash_clk_ctrl: dsi_esc_clk - clk_set_rate failed
<6>[    1.167999] FrameBuffer[0] 1200x1920 size=28016640 bytes is registered successfully!
<7>[    1.168395] Registered led device: lcd-backlight
<6>[    1.168487] mipi_JDI_lcd_probe-
<6>[    1.168548] mipi_JDI_1080P_pt_init-
<6>[    1.169342] setting pdata->panel_info.fb_num to 1. type: 7
<6>[    1.169982] FrameBuffer[1] 1920x1080 size=0 bytes is registered successfully!
<6>[    1.170318] mdp4_dtv_vsync_init: ndx=0
<3>[    1.170471] hdmi_msm hdmi_msm.1: external_common_state_create: sysfs group ed883a08
<7>[    1.170593] EXT_COMMON: external_common_state_create: kobject_uevent(KOBJ_ADD)
<6>[    1.170623] hdmi_msm hdmi_msm.1: hdmi_msm_config_hdcp_feature: HDCP Feature: Enabled
<6>[    1.171386] 
<6>[    1.171386]  msm_vidc_enc: Inside vid_enc_init()
<6>[    1.171691] 
<6>[    1.171691]  msm_vidc_enc: Inside vid_enc_vcd_init()
<6>[    1.172546] msm_serial_hs module loaded
<6>[    1.172821] msm_serial_hsl: detected port #1
<6>[    1.173004] msm_serial_hsl.1: ttyHSL1 at MMIO 0x12450000 (irq = 225) is a MSM
<6>[    1.173248] msm_serial_hsl: detected port #0
<6>[    1.173400] msm_serial_hsl.0: ttyHSL0 at MMIO 0x16640000 (irq = 190) is a MSM
<6>[    1.173675] msm_serial_hsl: driver initialized
<6>[    1.174774] msm_rotator_probe: rotator_hw_revision=2
<6>[    1.176513] diagchar initialized now
<6>[    1.177490] kgsl kgsl-3d0: |kgsl_iommu_init| MMU type set for device is IOMMU
<6>[    1.182617] brd: module loaded
<6>[    1.184875] loop: module loaded
<6>[    1.186492] anx7808 init gpio
<6>[    1.261718] sp_tx_hardware_poweron: anx7808 power on
<6>[    1.262512] ANX7808 is found.
<5>[    1.263732] 3.3V output disabled
<6>[    1.321350] sp_tx_hardware_powerdown: anx7808 power down
<5>[    1.321472] SP_TX To System State: 
<5>[    1.321533] STATE_CABLE_PLUG
<6>[    1.321929] tabla-slim tabla-slim: Platform data from board file
<3>[    1.482116] wcd9xxx_slim_probe: failed to get slimbus tabla-slim logical address: -6
<6>[    1.484497] tabla2x-slim tabla2x-slim: Platform data from board file
<6>[    1.547424] wcd9xxx_check_codec_type: codec is tabla_codec
<6>[    1.547546] wcd9xxx_check_codec_type: Read codec idbytes & version
<6>[    1.547546] byte_0[00000002] byte_1[00000000] byte_2[00000000]
<6>[    1.547546]  byte_3[00000001] version = 2
<4>[    1.548370] i2c-core: driver [tabla-i2c-core] using legacy suspend method
<4>[    1.548492] i2c-core: driver [tabla-i2c-core] using legacy resume method
<6>[    1.549041] bcm2079x-i2c 0-0077: bcm2079x_probe, probing bcm2079x driver flags = 0
<6>[    1.549255] bcm2079x-i2c 0-0077: requesting IRQ 320
<6>[    1.549377] bcm2079x-i2c 0-0077: bcm2079x_probe, probing bcm2079x driver exited successfully
<6>[    1.549804] SCSI Media Changer driver v0.25 
<6>[    1.550201] spi_qsd spi_qsd.0: master is unqueued, this is deprecated
<6>[    1.551239] tun: Universal TUN/TAP device driver, 1.6
<6>[    1.551300] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
<6>[    1.551483] rmnet_init: BAM devices[8]
<6>[    1.558685] PPP generic driver version 2.4.2
<6>[    1.558868] PPP BSD Compression module registered
<6>[    1.558959] PPP Deflate Compression module registered
<6>[    1.559326] PPP MPPE Compression module registered
<6>[    1.559387] NET: Registered protocol family 24
<6>[    1.559478] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
<6>[    1.559600] CSLIP: code copyright 1989 Regents of the University of California.
<6>[    1.559783] wcnss_wlan probed in built-in mode
<6>[    1.560302] usbcore: registered new interface driver asix
<6>[    1.560424] usbcore: registered new interface driver cdc_ether
<6>[    1.560516] usbcore: registered new interface driver net1080
<6>[    1.560668] usbcore: registered new interface driver cdc_subset
<6>[    1.560760] usbcore: registered new interface driver zaurus
<6>[    1.560974] usbcore: registered new interface driver cdc_ncm
<4>[    1.561065] smb345_probe+
<5>[    1.564147] smb345_charger: [smb345_inok_irq] GPIO pin irq 311 requested ok, smb345_INOK = L
<5>[    1.564270] smb345_charger: [smb345_wireless_irq] GPIO pin irq 322 requested ok, wpc_pok = H
<5>[    1.564392] smb345_charger: [smb345_wireless_en_config] GPIO pin 179, 183 requested ok, wpc_en1 = L, wpc_en2 = L
<4>[    1.564514] smb345_probe-
<4>[    1.564605] i2c-core: driver [smb345] using legacy suspend method
<4>[    1.564727] i2c-core: driver [smb345] using legacy resume method
<5>[    1.564819] bq27541_probe + client->addr= 55
<5>[    1.565887] bq27541_get_psp status: Not charging ret= 0x0201
<5>[    1.566772] bq27541_get_psp voltage_now= 4285000 uV
<5>[    1.567718] bq27541_get_capacity = 99% ret= 98
<5>[    1.568634] bq27541_get_psp temperature= 281 (0.1�XC)
<5>[    1.570373] bq27541_get_psp current = -130 mA
<5>[    1.571380] bq27541_get_psp status: Not charging ret= 0x0201
<5>[    1.572082] setup_low_battery_irq irq=317, LL_BAT_T30=1
<5>[    1.572204] bq27541_probe - bq27541-battery driver registered
<5>[    1.572357] bq27541_get_psp status: Not charging ret= 0x0201
<4>[    1.572937] i2c-core: driver [bq27541-battery] using legacy suspend method
<4>[    1.573028] i2c-core: driver [bq27541-battery] using legacy resume method
<6>[    1.573211] msm_otg msm_otg: msm_otg probe
<5>[    1.573333] bq27541_get_psp voltage_now= 4285000 uV
<3>[    1.573944] msm_otg msm_otg: failed to get phy_clk
<6>[    1.574035] msm_otg msm_otg: OTG regs = f030c000
<5>[    1.574310] bq27541_get_capacity = 99% ret= 98
<5>[    1.575225] bq27541_get_psp temperature= 281 (0.1�XC)
<3>[    1.576019] msm_otg msm_otg: PMIC IRQ for ID notifications doesn't exist
<7>[    1.576263] gpio_request: gpio-23 (msm_otg_ap_acok) status -16
<4>[    1.576263] gpio 23 request failed 
<4>[    1.576354] msm_otg_acok_init: GPIO pin irq 311 requested ok, msm_otg_ACOK = L
<7>[    1.576538] gpio_request: gpio-77 (msm_otg_id_pin) status -16
<4>[    1.576538] gpio 77 request failed 
<5>[    1.576660] bq27541_get_psp current = -130 mA
<4>[    1.576690] msm_otg_id_pin_init: GPIO pin irq 365 requested ok, msm_otg_id_pin = H
<6>[    1.576873] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[    1.577514] usbcore: registered new interface driver cdc_acm
<6>[    1.577575] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[    1.577697] Initializing USB Mass Storage driver...
<6>[    1.577789] usbcore: registered new interface driver usb-storage
<6>[    1.577911] USB Mass Storage support registered.
<6>[    1.578002] usbcore: registered new interface driver ums-alauda
<6>[    1.578125] usbcore: registered new interface driver ums-cypress
<6>[    1.578216] usbcore: registered new interface driver ums-datafab
<6>[    1.578338] usbcore: registered new interface driver ums-freecom
<6>[    1.578491] usbcore: registered new interface driver ums-isd200
<6>[    1.578582] usbcore: registered new interface driver ums-jumpshot
<6>[    1.578704] usbcore: registered new interface driver ums-karma
<6>[    1.578796] usbcore: registered new interface driver ums-onetouch
<6>[    1.578918] usbcore: registered new interface driver ums-sddr09
<6>[    1.579010] usbcore: registered new interface driver ums-sddr55
<6>[    1.579132] usbcore: registered new interface driver ums-usbat
<6>[    1.579284] usbcore: registered new interface driver usbserial
<6>[    1.579376] usbserial: USB Serial Driver core
<6>[    1.579467] usbcore: registered new interface driver qc_csvt
<6>[    1.579620] USB Serial support registered for qc_csvt
<6>[    1.579711] usbcore: registered new interface driver usb_ehset_test
<6>[    1.579833] usbcore: registered new interface driver diag_bridge
<6>[    1.580047] usbcore: registered new interface driver mdm_bridge
<6>[    1.580596] usbcore: registered new interface driver ks_bridge
<6>[    1.580688] ksb_init: init done
<6>[    1.580932] msm_otg msm_otg: phy_reset: success
<6>[    1.581512] msm_hsusb msm_hsusb: [ci13xxx_start] hw_ep_max = 32
<6>[    1.581726] mbim_init: initialize 1 instances
<6>[    1.581878] mbim_init: Initialized 1 ports
<6>[    1.583007] rndis_qc_init: initialize rndis QC instance
<6>[    1.583343] android_usb gadget: Mass Storage Function, version: 2009/09/11
<6>[    1.583404] android_usb gadget: Number of LUNs=1
<6>[    1.583526]  lun0: LUN: removable file: (no medium)
<6>[    1.583770] android_usb gadget: android_usb ready
<6>[    1.584289] mousedev: PS/2 mouse device common for all mice
<6>[    1.584777] usbcore: registered new interface driver xpad
<4>[    1.584869] [ektf3k]:[elan] elan_ktf3k_ts_init
<4>[    1.585083] [ektf3k]:[ELAN] Start HW reset!
<4>[    1.681518] [usb_otg] switch to peripheral mode by default (boot)
<4>[    1.841644] [ektf3k]:[elan]detect intr=>Old FW
<4>[    1.841705] [ektf3k]:The boot code is old!
<4>[    1.871765] [ektf3k]:[elan] __hello_packet_handler: hello packet 55:55:55:55
<4>[    1.871856] [ektf3k]:[elan] hello packet's rc = 0
<4>[    2.083465] [ektf3k]:[elan] __fw_packet_handler: firmware version: 0xa044
<4>[    2.085418] [ektf3k]:[elan] __fw_packet_handler: X resolution: 0x007e
<4>[    2.087402] [ektf3k]:[elan] __fw_packet_handler: Y resolution: 0x00d2
<4>[    2.089324] [ektf3k]:[elan] __fw_packet_handler: firmware id: 0x3029
<4>[    2.091308] [ektf3k]:[elan] __fw_packet_handler: boot code id: 0x6047
<4>[    2.091369] [ektf3k]:[Elan] Max X=2239, Max Y=1343
<6>[    2.091613] input: elan-touchscreen as /devices/virtual/input/input0
<4>[    2.091857] [ektf3k]:The firmware was version 0xA042 and id:0x3029
<4>[    2.092010] [ektf3k]: /proc/ektf_dbg created
<4>[    2.092254] [ektf3k]:[elan] Start touchscreen elan-touchscreen in interrupt mode
<4>[    2.092407] [ektf3k]:[ELAN]misc_register finished!!
<6>[    2.092498] elan-ktf3k 3-0010: Update power source to 0
<6>[    2.092987] lis3dh_acc accelerometer driver: init
<4>[    2.093078] i2c-core: driver [lis3dh_acc] using legacy suspend method
<4>[    2.093200] i2c-core: driver [lis3dh_acc] using legacy resume method
<6>[    2.093414] ASUSTek: lid_driver_probe
<6>[    2.093627] input: lid_input as /devices/virtual/input/input1
<6>[    2.094573] using rtc device, pm8xxx_rtc, for alarms
<6>[    2.094696] rtc-pm8xxx rtc-pm8xxx: rtc core: registered pm8xxx_rtc as rtc0
<6>[    2.095031] i2c /dev entries driver
<3>[    2.096923] ov5693_init_module:105
<3>[    2.097137] ov5693_init_module:110 rc -19
<3>[    2.131591] gpio 25 VCM_PD(1)
<3>[    2.131683] gpio 31 XSHUTDN(1)
<6>[    2.186126] mi1040_init_module:323
<3>[    2.186401] mi1040_init_module:329 rc -19
<3>[    2.361694] gpio 43 CAM_RST(1)
<6>[    2.421661] mi1040_sensor_match_id +++
<6>[    2.422332] Sensor id: 0x2481
<6>[    2.422424] PMIC gpio 11 CAM_VENDOR_1(0)
<6>[    2.422546] PMIC gpio 10 CAM_VENDOR_0(0)
<6>[    2.422637] PMIC gpio 24 CAM_LENS(0)
<6>[    2.422698] Vendor is B
<6>[    2.422760] mi1040_sensor_match_id ---
<6>[    2.662689] lirc_dev: IR Remote Control driver registered, major 237 
<6>[    2.662750] IR NEC protocol handler initialized
<6>[    2.662872] IR RC5(x) protocol handler initialized
<6>[    2.662933] IR RC6 protocol handler initialized
<6>[    2.663055] IR JVC protocol handler initialized
<6>[    2.663116] IR Sony protocol handler initialized
<6>[    2.663177] IR RC5 (streamzap) protocol handler initialized
<6>[    2.663299] IR SANYO protocol handler initialized
<6>[    2.663360] IR MCE Keyboard/mouse protocol handler initialized
<6>[    2.663482] IR LIRC bridge handler initialized
<6>[    2.663787] gspca_main: v2.14.0 registered
<6>[    2.664093] usbcore: registered new interface driver uvcvideo
<6>[    2.664154] USB Video Class driver (1.1.1)
<3>[    2.665100] pm8xxx_adc_probe: failed to request pa_therm vreg with error -517
<6>[    2.665710] CAP1106: [cap1106_init] 
<4>[    2.665802] i2c-core: driver [cap1106] using legacy suspend method
<4>[    2.665924] i2c-core: driver [cap1106] using legacy resume method
<6>[    2.687225] pm8xxx_tm_probe: OK
<6>[    2.687652] pm8xxx_tm_probe: OK
<6>[    2.688262] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
<6>[    2.688476] Bluetooth: HCI UART driver ver 2.2
<6>[    2.688537] Bluetooth: HCI H4 protocol initialized
<6>[    2.688659] Bluetooth: HCIATH3K protocol initialized
<6>[    2.688903] Bluetooth: HCI_IBS protocol initialized
<6>[    2.689910] cpuidle: using governor ladder
<6>[    2.690032] cpuidle: using governor menu
<6>[    2.690399] mmc0: SDCC Version: 0x06000018
<6>[    2.691558] mmc0: bam physical base=0x12402000
<6>[    2.691680] mmc0: bam virtual base=0xf0328000
<6>[    2.691741] sps:BAM 0x12402000 is registered.
<6>[    2.691864] mmc0: BAM device registered. bam_handle=0xc1e98c00
<6>[    2.692108] sps:BAM 0x12402000 enabled: ver:0x5, number of pipes:6
<6>[    2.692443] mmc0: Qualcomm MSM SDCC-BAM at 0x0000000012402000 irq 130
<6>[    2.692596] mmc0: Qualcomm MSM SDCC-DML at 0x0000000012400800
<3>[    2.692718] mmc0: No card detect facilities available
<6>[    2.694458] mmc0: Qualcomm MSM SDCC-core at 0x0000000012400000 irq 136,0 dma -1 dmacrcri -1
<6>[    2.694580] mmc0: Controller capabilities: 0x0000039a
<6>[    2.694641] mmc0: 8 bit data mode enabled
<6>[    2.694763] mmc0: 4 bit data mode disabled
<6>[    2.694824] mmc0: polling status mode disabled
<6>[    2.694946] mmc0: MMC clock 400000 -> 96000000 Hz, PCLK 0 Hz
<6>[    2.695037] mmc0: Slot eject status = 0
<6>[    2.695098] mmc0: Power save feature enable = 1
<6>[    2.695190] mmc0: SPS-BAM data transfer mode available
<6>[    2.696716] usbcore: registered new interface driver usbhid
<6>[    2.696838] usbhid: USB HID core driver
<6>[    2.696899] zram: num_devices not specified. Using default: 1
<6>[    2.697021] zram: Creating 1 devices ...
<6>[    2.697937] ashmem: initialized
<6>[    2.698059] logger: created 256K log 'log_main'
<6>[    2.698242] logger: created 256K log 'log_events'
<6>[    2.698364] logger: created 256K log 'log_radio'
<6>[    2.698455] logger: created 256K log 'log_system'
<6>[    2.699005] usbcore: registered new interface driver snd-usb-audio
<3>[    2.699859] tabla_probe
<6>[    2.700836] msm_pcm_probe: dev name msm-voip-dsp
<6>[    2.701049] msm-dai-q6-mi2s msm-dai-q6-mi2s: msm_dai_q6_mi2s_platform_data_validation: playback sdline 0 capture sdline 8
<6>[    2.701171] msm-dai-q6-mi2s msm-dai-q6-mi2s: msm_dai_q6_mi2s_platform_data_validation: playback ch_max 0 capture ch_mx 8
<6>[    2.701965] msm_pcm_probe: dev name msm-pcm-dsp
<6>[    2.702209] msm_pcm_probe: dev name msm-multi-ch-pcm-dsp
<6>[    2.702484] msm_pcm_probe: dev name msm-lowlatency-pcm-dsp
<6>[    2.702545] adding pm_qos request in low latency driver
<6>[    2.702667] done adding pm_qos request in low latency driver
<6>[    2.703216] msm_compr_probe: dev name msm-compr-dsp
<6>[    2.703613] msm-pcm-lpa msm-pcm-lpa: msm_pcm_probe: dev name msm-pcm-lpa
<3>[    2.704223] msm8930_audio_init: Not the right machine type
<3>[    2.704345] msm_audio_init: Not the right machine type
<6>[    2.704406] msm_audio_init: Not APQ8064 in I2S mode
<6>[    2.794555] asoc: snd-soc-dummy-dai <-> MultiMedia1 mapping ok
<6>[    2.794921] asoc: snd-soc-dummy-dai <-> MultiMedia2 mapping ok
<6>[    2.795349] asoc: snd-soc-dummy-dai <-> CS-VOICE mapping ok
<6>[    2.795715] asoc: snd-soc-dummy-dai <-> VoIP mapping ok
<6>[    2.796142] asoc: snd-soc-dummy-dai <-> MultiMedia3 mapping ok
<6>[    2.796508] asoc: snd-soc-dummy-dai <-> SLIMBUS0_HOSTLESS mapping ok
<6>[    2.796905] asoc: snd-soc-dummy-dai <-> INT_FM_HOSTLESS mapping ok
<6>[    2.797210] asoc: msm-stub-rx <-> msm-dai-q6.241 mapping ok
<6>[    2.797546] asoc: msm-stub-tx <-> msm-dai-q6.240 mapping ok
<6>[    2.797943] asoc: snd-soc-dummy-dai <-> MultiMedia4 mapping ok
<6>[    2.798370] asoc: snd-soc-dummy-dai <-> AUXPCM_HOSTLESS mapping ok
<6>[    2.798706] asoc: snd-soc-dummy-dai <-> HDMI_HOSTLESS mapping ok
<6>[    2.799102] asoc: snd-soc-dummy-dai <-> VOICE_STUB mapping ok
<6>[    2.799468] asoc: snd-soc-dummy-dai <-> VoLTE mapping ok
<6>[    2.799896] asoc: snd-soc-dummy-dai <-> MultiMedia5 mapping ok
<6>[    2.800567] asoc: tabla_rx1 <-> msm-dai-q6.16384 mapping ok
<6>[    2.802673] asoc: tabla_tx1 <-> msm-dai-q6.16385 mapping ok
<6>[    2.802947] asoc: msm-stub-rx <-> msm-dai-q6.12288 mapping ok
<6>[    2.803283] asoc: msm-stub-tx <-> msm-dai-q6.12289 mapping ok
<6>[    2.803588] asoc: msm-stub-rx <-> msm-dai-q6.12292 mapping ok
<6>[    2.803924] asoc: msm-stub-tx <-> msm-dai-q6.12293 mapping ok
<6>[    2.804199] asoc: msm-stub-rx <-> msm-dai-q6-hdmi.8 mapping ok
<6>[    2.804534] asoc: msm-stub-rx <-> msm-dai-q6.224 mapping ok
<6>[    2.804809] asoc: msm-stub-tx <-> msm-dai-q6.225 mapping ok
<6>[    2.805145] asoc: msm-stub-rx <-> msm-dai-q6.2 mapping ok
<6>[    2.805419] asoc: msm-stub-tx <-> msm-dai-q6.3 mapping ok
<6>[    2.805786] asoc: tabla_rx2 <-> msm-dai-stub mapping ok
<6>[    2.806060] asoc: tabla_tx1 <-> msm-dai-stub mapping ok
<6>[    2.806396] asoc: msm-stub-rx <-> msm-dai-q6.16386 mapping ok
<6>[    2.806671] asoc: msm-stub-tx <-> msm-dai-q6.16387 mapping ok
<6>[    2.807067] asoc: tabla_tx2 <-> msm-dai-q6.16389 mapping ok
<6>[    2.807373] asoc: tabla_rx3 <-> msm-dai-q6.16388 mapping ok
<6>[    2.807678] asoc: msm-stub-rx <-> msm-dai-q6.16392 mapping ok
<6>[    2.807952] asoc: msm-stub-tx <-> msm-dai-q6.16393 mapping ok
<6>[    2.808288] asoc: tabla_tx3 <-> msm-dai-stub mapping ok
<6>[    2.808563] asoc: msm-stub-rx <-> msm-dai-q6.16390 mapping ok
<6>[    2.808898] asoc: msm-stub-tx <-> msm-dai-q6.16391 mapping ok
<6>[    2.810089] input: apq8064-tabla-snd-card Button Jack as /devices/platform/soc-audio.0/sound/card0/input2
<6>[    2.810394] input: apq8064-tabla-snd-card Headset Jack as /devices/platform/soc-audio.0/sound/card0/input3
<6>[    2.812500] headset_init+ #####
<6>[    2.812988] input: h2w button as /devices/virtual/input/input4
<6>[    2.813262] HEADSET: Headset detection mode
<6>[    2.818572] mmc0: new HS200 MMC card at address 0001
<6>[    2.819030] mmcblk0: mmc0:0001 MMC32G 28.8 GiB 
<6>[    2.823333] mmc0: mmc_start_bkops: raw_bkops_status=0x2, from_exception=1
<6>[    2.825256]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30
<6>[    2.871826] set_hs_micbias badgap status: OFF power down bandgap
<6>[    2.871948] headset_init- #####
<6>[    2.872070] u32 classifier
<6>[    2.872192]     Actions configured
<6>[    2.872253] Netfilter messages via NETLINK v0.30.
<6>[    2.872375] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
<6>[    2.872985] ctnetlink v0.93: registering with nfnetlink.
<6>[    2.873077] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[    2.873199] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[    2.873443] xt_time: kernel timezone is -0000
<6>[    2.873870] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[    2.874145] arp_tables: (C) 2002 David S. Miller
<6>[    2.874328] TCP: cubic registered
<6>[    2.874816] NET: Registered protocol family 10
<6>[    2.876861] Mobile IPv6
<6>[    2.877014] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[    2.877197] IPv6 over IPv4 tunneling driver
<6>[    2.877655] NET: Registered protocol family 17
<6>[    2.877777] NET: Registered protocol family 15
<6>[    2.877960] Bluetooth: RFCOMM TTY layer initialized
<6>[    2.878082] Bluetooth: RFCOMM socket layer initialized
<6>[    2.878143] Bluetooth: RFCOMM ver 1.11
<6>[    2.878234] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[    2.878326] Bluetooth: BNEP filters: protocol multicast
<6>[    2.878417] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[    2.878601] L2TP core driver, V2.0
<6>[    2.878692] PPPoL2TP kernel driver, V2.0
<5>[    2.878753] Registering the dns_resolver key type
<6>[    2.879302] VFP support v0.3: implementor 51 architecture 64 part 6f variant 1 rev 0
<5>[    2.879486] Registering SWP/SWPB emulation handler
<6>[    2.879577] clock_late_init: Removing enables held for handed-off clocks
<6>[    2.883453] MSM Watchdog Initialized
<7>[    2.894165] gpio_set_debounce: gpio-26 status -22
<7>[    2.894317] gpio_set_debounce: gpio-155 status -22
<7>[    2.894409] gpio_set_debounce: gpio-189 status -22
<6>[    2.894653] input: gpio-keys as /devices/platform/gpio-keys.0/input/input5
<6>[    2.895080] rtc-pm8xxx rtc-pm8xxx: setting system clock to 1970-01-25 00:20:16 UTC (2074816)
<3>[    2.895385] MSM_DCVS: msm_dcvs_register_core: msm_dcvs_register_core: scm register core fail handle = 1 ret = -22
<3>[    2.895538] Unable to register core for 0
<4>[    2.895660] msm_dcvs_gov: probe of msm_dcvs_gov failed with error -22
<6>[    2.896026] ALSA device list:
<6>[    2.896087]   #0: apq8064-tabla-snd-card
<6>[    2.896423] Freeing init memory: 116K
<7>[    2.901184] SELinux: 512 avtab hash slots, 1574 rules.
<7>[    2.901794] SELinux: 512 avtab hash slots, 1574 rules.
<7>[    2.901947] SELinux:  1 users, 2 roles, 288 types, 13 bools, 1 sens, 1024 cats
<7>[    2.901977] SELinux:  84 classes, 1574 rules
<7>[    2.902740] SELinux:  Completing initialization.
<7>[    2.902740] SELinux:  Setting up existing superblocks.
<7>[    2.902770] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
<7>[    2.902801] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
<7>[    2.903503] SELinux: initialized (dev bdev, type bdev), not configured for labeling
<7>[    2.903533] SELinux: initialized (dev proc, type proc), uses genfs_contexts
<7>[    2.903564] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
<7>[    2.903594] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
<7>[    2.913848] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
<7>[    2.913879] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
<7>[    2.913909] SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
<7>[    2.913909] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
<7>[    2.913940] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
<7>[    2.914062] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
<7>[    2.914123] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
<5>[    3.088989] type=1403 audit(2074816.680:2): policy loaded auid=4294967295 ses=4294967295
<4>[    3.089263] SELinux: Loaded policy from (null)
<3>[    3.093292] init: /init.rc: 42: invalid command 'powerctl'
<3>[    3.093475] init: could not import file '/init.recovery.flo.rc' from '/init.rc'
<3>[    3.095672] init: cannot find '/sbin/healthd', disabling 'healthd'
<6>[    3.101867] notifying plugin
<5>[    3.105895] bq27541_get_psp status: Not charging ret= 0x0201
<5>[    3.106597] bq27541_get_psp voltage_now= 4269000 uV
<5>[    3.107238] bq27541_get_capacity = 99% ret= 98
<5>[    3.107879] bq27541_get_psp temperature= 281 (0.1�XC)
<5>[    3.109100] bq27541_get_psp current = -342 mA
<6>[    3.232116] msm_otg msm_otg: chg_type = USB_SDP_CHARGER
<5>[    3.232238] smb345_charger: [usb_cable_type_detect] INOK=L
<5>[    3.232330] smb345_charger: [usb_cable_type_detect] Cable: SDP
<5>[    3.232849] smb345_charger: [smb345_vflt_setting] Bypass set Float Volt=e8
<4>[    3.233184] ========================================================
<4>[    3.233306] bq27541_battery_callback  usb_cable_state = 1
<4>[    3.233367] ========================================================
<6>[    3.233489] battery_callback cable_wake_lock 5 sec...
<6>[    3.233489]  
<6>[    3.233612] elan-ktf3k 3-0010: Update power source to 1
<6>[    3.233978] The USB cable status = CHARGER_SDP
<6>[    3.238525] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_RESET_EVENT received
<3>[    3.328399] init: cannot open '/initlogo.rle'
<3>[    3.329620] enable_store: android_usb: already disabled
<3>[    3.330200] init: Unable to open persistent property directory /data/property errno: 2
<6>[    3.334411] adb_open
<6>[    3.334533] adb_bind_config
<4>[    3.344940] mipi_dsi_panel_power+, on=1
<4>[    3.421936] mipi_dsi_panel_power-
<6>[    3.427551] mipi_JDI_lcd_on+
<6>[    3.427551] mipi_JDI_lcd_on-, booting
<6>[    3.453491] mipi_JDI_set_recovery_backlight: 100/255
<3>[    3.483367] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
<6>[    3.483428] android_work: android_work: did not send uevent (0 0   (null))
<6>[    3.548828] android_work: android_work: sent uevent USB_STATE=CONNECTED
<3>[    3.552368] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
<6>[    3.552581] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
<6>[    3.631988] android_work: android_work: sent uevent USB_STATE=CONNECTED
<6>[    3.633392] android_usb gadget: high-speed config #1: android_usb
<3>[    3.633514] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
<6>[    3.633575] msm_otg msm_otg: Avail curr from USB = 500
<6>[    3.692230] android_work: android_work: sent uevent USB_STATE=CONFIGURED
<4>[    4.853118] adbd (154): /proc/154/oom_adj is deprecated, please use /proc/154/oom_score_adj instead.
<5>[    5.233337] bq27541_get_psp status: Charging ret= 0x0201
<5>[    5.233489] smb345_charger: [smb345_config_thermal_limit] Set HRD SFT limit, retval=41 setting=73
<5>[    5.234161] bq27541_get_psp status: Charging ret= 0x0201
<5>[    5.234619] smb345_charger: [smb345_config_thermal_charging] temp=28, volt=4269000
<5>[    5.235015] bq27541_get_psp voltage_now= 4285000 uV
<5>[    5.235870] bq27541_get_capacity = 99% ret= 98
<5>[    5.235992] smb345_charger: [smb345_config_thermal_charging] Bypass set Float Volt=e8
<5>[    5.236724] bq27541_get_psp temperature= 282 (0.1�XC)
<5>[    5.236877] smb345_charger: [smb345_config_thermal_charging] Bypass charger enable
<5>[    5.238250] bq27541_get_psp current = -64 mA
<3>[    7.806030] mmc0: CMD25: Data timeout
<6>[    7.806152] mmc0: SDCC PWR is ON
<6>[    7.806213] mmc0: SDCC clks are ON, MCLK rate=96000000
<6>[    7.806243] mmc0: SDCC irq is enabled
<6>[    7.806365] ===== SDCC-CORE: Register Dumps @phys_base=0x12400000, @virt_base=0xf0324000 =====
<6>[    7.806488] Reg=0x00: 0x00000001, 0x01209f00, 0x00500000, 0x00001459
<6>[    7.806518] Reg=0x10: 0x00000019, 0x00000940, 0x0f5903ff, 0xffffffe0
<6>[    7.806640] Reg=0x20: 0x8a400042, 0x124f8fa0, 0x00001000, 0x000a2009
<6>[    7.806701] Reg=0x30: 0x00000000, 0x000c0400, 0x00000000, 0x408001ff
<6>[    7.806793] Reg=0x40: 0x00000000, 0x00000000, 0x00000000, 0x00000000
<6>[    7.806854] Reg=0x50: 0x06000018, 0x00000000, 0x00000000, 0x00000000
<6>[    7.806976] Reg=0x60: 0x60006400, 0x00000000, 0x00000000, 0x00000000
<6>[    7.807037] mmc0: SPS mode: busy=0
<6>[    7.807098] mmc0: xfer_size=4096, data_xfered=4096, xfer_remain=0
<3>[    7.807159] mmc0: got_dataend=0, prog_enable=0, wait_for_auto_prog_done=1, got_auto_prog_done=0, req_tout_ms=10000
<6>[    7.807281] mmc0: PM: sdcc_suspended=0, pending_resume=0, sdcc_suspending=0
<6>[    7.807373] mmc0: RPM: runtime_status=0, usage_count=1, is_suspended=0, disable_depth=0, runtime_error=0, request_pending=0, request=0
<3>[    7.807495] mmc0: Overlapping command requests
<6>[    7.807708] sps:BAM 0x12402000 enabled: ver:0x5, number of pipes:6
<3>[    7.807983] mmcblk0: error -110 sending stop command, original cmd response 0x940, card status 0x2400e40