Skip to content

Instantly share code, notes, and snippets.

@macbre

macbre/boot.txt

Last active December 3, 2024 23:36
Show Gist options
  • Save macbre/0b0334f904950335afc2343c2ea513ea to your computer and use it in GitHub Desktop.
Save macbre/0b0334f904950335afc2343c2ea513ea to your computer and use it in GitHub Desktop.
Download ZIP
Alix 6d2
Raw
boot.txt
INIT: Entering runlevel: 2
Booting 'voyage-linux-03Jan10'
root (hd0,0)
Filesystem type is ext2fs, partition type 0x83
kernel /vmlinuz root=LABEL=ROOT_FS console=ttyS0,115200n8
[Linux-bzImage, setup=0x3000, size=0x163bd0]
initrd /initrd.img
[Linux-initrd @ 0xfa87000, 0x56834b bytes]
Probing EDD (edd=off to disable)... ok
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-486 (Debian 2.6.26-25lenny1) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Thu Sep 16 18:43:30 UTC 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] 256MB LOWMEM available.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 65536
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65536
[ 0.000000] DMI not present or invalid.
[ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321]
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:eff00000)
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=LABEL=ROOT_FS console=ttyS0,115200n8
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 498.053 MHz processor.
[ 0.004000] Console: colour dummy device 80x25
[ 0.004000] console [ttyS0] enabled
[ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.004000] Memory: 250640k/262144k available (1697k kernel code, 10984k reserved, 746k data, 320k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB)
[ 0.004000] vmalloc : 0xd0800000 - 0xfffb1000 ( 759 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.004000] .init : 0xc0366000 - 0xc03b6000 ( 320 kB)
[ 0.004000] .data : 0xc02a8545 - 0xc0363000 ( 746 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02a8545 (1697 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.084535] Calibrating delay using timer specific routine.. 998.10 BogoMIPS (lpj=1996207)
[ 0.093010] Security Framework initialized
[ 0.097147] SELinux: Disabled at boot.
[ 0.101013] Capability LSM initialized
[ 0.104839] Mount-cache hash table entries: 512
[ 0.109823] Initializing cgroup subsys ns
[ 0.113860] Initializing cgroup subsys cpuacct
[ 0.118326] Initializing cgroup subsys devices
[ 0.122849] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
[ 0.128008] CPU: L2 Cache: 128K (32 bytes/line)
[ 0.132008] CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02
[ 0.139012] Checking 'hlt' instruction... OK.
[ 0.164010] Freeing SMP alternatives: 0k freed
[ 0.168010] ACPI: Core revision 20080321
[ 0.172010] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321]
[ 0.180011] ACPI: Unable to load the System Description Tables
[ 0.184319] net_namespace: 652 bytes
[ 0.187914] Booting paravirtualized kernel on bare hardware
[ 0.192012] NET: Registered protocol family 16
[ 0.196078] EISA bus registered
[ 0.199909] PCI: PCI BIOS revision 2.10 entry at 0xfcd03, last bus=0
[ 0.204012] PCI: Using configuration type 1 for base access
[ 0.208013] Setting up standard PCI resources
[ 0.214044] ACPI: Interpreter disabled.
[ 0.217954] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.223765] pnp: PnP ACPI: disabled
[ 0.227286] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.232014] PnPBIOS: PnP BIOS support was not detected.
[ 0.236014] PCI: Probing PCI hardware
[ 0.244902] NET: Registered protocol family 2
[ 0.249690] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.257658] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.264896] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.271494] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.277877] TCP reno registered
[ 0.282128] NET: Registered protocol family 1
[ 0.287047] checking if image is initramfs... it is
[ 3.592191] Freeing initrd memory: 5536k freed
[ 3.600191] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 3.605926] audit: initializing netlink socket (disabled)
[ 3.611384] type=2000 audit(946684811.611:1): initialized
[ 3.617659] Total HugeTLB memory allocated, 0
[ 3.622257] VFS: Disk quotas dquot_6.5.1
[ 3.626346] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.632994] msgmni has been set to 500
[ 3.637310] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.644734] io scheduler noop registered
[ 3.648686] io scheduler anticipatory registered
[ 3.653330] io scheduler deadline registered
[ 3.657666] io scheduler cfq registered (default)
[ 3.663576] isapnp: Scanning for PnP cards...
[ 4.024211] isapnp: No Plug & Play device found
[ 4.038769] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 4.046790] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.060219] brd: module loaded
[ 4.063797] PNP: No PS/2 controller found. Probing ports directly.
[ 4.070950] i8042.c: No controller found.
[ 4.075254] mice: PS/2 mouse device common for all mice
[ 4.084219] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 4.088258] rtc0: alarms up to one day
[ 4.092431] EISA: Probing bus 0 at eisa.0
[ 4.096489] Cannot allocate resource for EISA slot 1
[ 4.101529] Cannot allocate resource for EISA slot 6
[ 4.106541] EISA: Detected 0 cards.
[ 4.110057] cpuidle: using governor ladder
[ 4.114181] cpuidle: using governor menu
[ 4.118136] No iBFT detected.
[ 4.123856] TCP cubic registered
[ 4.127114] NET: Registered protocol family 17
[ 4.131592] Using IPI Shortcut mode
[ 4.135572] registered taskstats version 1
[ 4.140181] rtc_cmos rtc_cmos: setting system clock to 2000-01-01 00:00:13 UTC (946684813)
[ 4.147599] Freeing unused kernel memory: 320k freed
Loading, please wait...
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... FATAL: Error inserting fan (/lib/modules/2.6.26-2-486/kernel/drivers/acpi/fan.ko): No such device
WARNING: Error inserting processor (/lib/modules/2.6.26-2-486/kernel/drivers/acp[ 4.656615] thermal: Unknown symbol acpi_processor_set_thermal_limit
i/processor.ko): No such device
FATAL: Error inserting thermal (/lib/modules/2.6.26-2-486/kernel/drivers/acpi/thermal.ko): Unknown symbol in module, or unknown parameter (see dmesg)
[ 6.095874] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 6.112322] eth0: VIA Rhine III (Management Adapter) at 0x11000, 00:0d:b9:17:cb:a8, IRQ 10.
[ 6.118479] eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
[ 6.136325] eth1: VIA Rhine III (Management Adapter) at 0x11400, 00:0d:b9:17:cb:a9, IRQ 11.
[ 6.142250] eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 6.299468] SCSI subsystem initialized
[ 6.379086] usbcore: registered new interface driver usbfs
[ 6.384613] usbcore: registered new interface driver hub
[ 6.390088] usbcore: registered new device driver usb
[ 6.466713] ehci_hcd 0000:00:0f.5: EHCI Host Controller
[ 6.472208] ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 1
[ 6.501145] ehci_hcd 0000:00:0f.5: irq 15, io mem 0xefffd000
[ 6.516632] ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 6.524495] usb usb1: configuration #1 chosen from 1 choice
[ 6.530265] hub 1-0:1.0: USB hub found
[ 6.534062] hub 1-0:1.0: 4 ports detected
[ 6.641391] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.648215] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.655468] usb usb1: Product: EHCI Host Controller
[ 6.660371] usb usb1: Manufacturer: Linux 2.6.26-2-486 ehci_hcd
[ 6.666317] usb usb1: SerialNumber: 0000:00:0f.5
[ 6.671311] ohci_hcd 0000:00:0f.4: OHCI Host Controller
[ 6.676665] ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 2
[ 6.684069] ohci_hcd 0000:00:0f.4: irq 15, io mem 0xefffe000
[ 6.777445] usb usb2: configuration #1 chosen from 1 choice
[ 6.783190] hub 2-0:1.0: USB hub found
[ 6.786997] hub 2-0:1.0: 4 ports detected
[ 6.892855] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.899684] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.906931] usb usb2: Product: OHCI Host Controller
[ 6.911836] usb usb2: Manufacturer: Linux 2.6.26-2-486 ohci_hcd
[ 6.917777] usb usb2: SerialNumber: 0000:00:0f.4
[ 6.967339] Uniform Multi-Platform E-IDE driver
[ 6.971909] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 6.994260] AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller
[ 7.000047] AMD5536: IDE controller (0x1022:0x209a rev 0x01) at PCI slot 0000:00:0f.2
[ 7.006511] AMD5536: not 100% native mode: will probe irqs later
[ 7.012578] AMD5536: IDE port disabled
[ 7.016357] ide0: BM-DMA at 0xff00-0xff07
[ 7.312635] hda: CF CARD 4GB, ATA DISK drive
[ 7.989147] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 7.996873] hda: UDMA/33 mode selected
[ 8.001135] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 8.104429] hda: max request size: 128KiB
[ 8.108443] hda: 7847280 sectors (4017 MB) w/1KiB Cache, CHS=7785/16/63
[ 8.116937] hda: hda1
done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd[ 9.678453] udevd version 125 started
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[ 13.593765] geode-aes: GEODE AES engine enabled.
[ 13.652173] input: PC Speaker as /class/input/input0
[ 13.673149] PCSP: Timer resolution is not sufficient (4000250nS)
[ 13.679198] PCSP: Make sure you have HPET and ACPI enabled.
[ 13.684814] PC-Speaker initialization failed.
[ 13.705330] pcspkr: probe of pcspkr failed with error -5
[ 13.870739] AMD Geode RNG detected
[ 13.909846] Error: Driver 'pcspkr' is already registered, aborting...
done.
Setting the system clock.
Activating swap...done.
[ 14.789595] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Setting the system clock.
Cleaning up ifupdown....
Loading kernel modules...[ 15.645087] natsemi dp8381x driver, version 2.1, Sept 11, 2006
[ 15.645100] originally by Donald Becker <[email protected]>
[ 15.645113] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
[ 15.950124] Registered led device: alix:1
[ 15.954244] Registered led device: alix:2
[ 15.958353] Registered led device: alix:3
[ 16.944080] Linux video capture interface: v2.00
[ 16.990116] usbcore: registered new interface driver gspca
[ 16.995644] gspca: gspca driver 01.00.20 registered
done.
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...failed.
Activating swapfile swap...done.
Copying /ro to /rw.
tar: ./var/lib/logrotate: time stamp 2008-10-08 17:34:00 is 276795213.166676245 s in the future
tar: ./var/lib: time stamp 2010-01-03 10:20:38 is 315825611.16626765 s in the future
tar: ./var: time stamp 2010-01-03 10:20:38 is 315825611.166157885 s in the future
tar: .: time stamp 2010-01-03 10:20:38 is 315825611.16605914 s in the future
Voyage is now setting up tmpfs for changed files...
tmpfs: mount back /lib/init/rw/var/log to /var/log
tmpfs: mount back /lib/init/rw/var/tmp to /var/tmp
Done.
Setting up resolvconf...done.
Setting up networking....
Configuring network interfaces...[ 21.800340] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
done.
Starting portmap daemon....
[ 24.073682] NET: Registered protocol family 10
[ 24.080540] lo: Disabled Privacy Extensions
Setting sensors limits.
INIT: Entering runlevel: 2
Starting watchdog keepalive daemon: wd_keepalive.
Starting system log daemon: syslogd.
Starting DNS forwarder and DHCP server: dnsmasq.
Starting OpenBSD Secure Shell server: sshd.
Not starting internet superserver: no services enabled. (warning).
Starting web server: lighttpd.
nocatsplash daemon disabled - read /etc/default/nocatsplash.
Starting PPTP Daemon: pptpd.
Starting Hardware RNG entropy gatherer daemon: rngd.
Starting Serial port to network proxy: ser2net.
Starting periodic command scheduler: crond.
Stopping watchdog keepalive daemon: wd_keepalive.
Starting watchdog daemon: watchdog.
Remounting / as read-write ... Done.
Removing /etc/nologin ... Done.
Remounting / as read-only ... Done.
/etc/rc2.d/S99voyage-util: line 53: echo: write error: Invalid argument
Debian GNU/Linux 5.0 alix ttyS0
alix login:
Raw
info.md

Info

$ uname -a
Linux alix 2.6.26-2-486 #1 Thu Sep 16 18:43:30 UTC 2010 i586 GNU/Linux

$ cat /proc/cpuinfo 
processor	: 0
vendor_id	: AuthenticAMD
cpu family	: 5
model		: 10
model name	: Geode(TM) Integrated Processor by AMD PCS
stepping	: 2
cpu MHz		: 498.053
cache size	: 128 KB
fdiv_bug	: no
hlt_bug		: no
f00f_bug	: no
coma_bug	: no
fpu		: yes
fpu_exception	: yes
cpuid level	: 1
wp		: yes
flags		: fpu de pse tsc msr cx8 sep pge cmov clflush mmx mmxext 3dnowext 3dnow
bogomips	: 998.12
clflush size	: 32
power management:

$ cat /proc/meminfo 
MemTotal:       256632 kB

Config

Network setup

In /etc/network/interfaces make sure the DHCP is used:

auto eth0
iface eth0 inet dhcp

SSH

On your local machine add the following to ~/.ssh/config:

Host alix
  HostName 192.168.0.200
  HostKeyAlgorithms=+ssh-dss

Now you can:

$ ssh alix
(...)
Linux alix 2.6.26-2-486 #1 Thu Sep 16 18:43:30 UTC 2010 i586

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
 __  __
 \ \/ /___ __  __ ___  ___  ___    Useful Commands:
  \  // _ \\ \/ /,-_ |/ _ |/ -_)     remountrw - mount disk as read-write
   \/ \___/ \  / \___,\_  |\___|     remountro - mount disk as read-only
           _/_/        _'_|          remove.docs - remove all docs and manpages 
     { V o y a g e } - L i n u x     
      < http://linux.voyage.hk >   Version: 0.6 (Build Date 20100103)


Last login: Thu Oct  7 23:47:41 2010 from 192.168.1.10
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment