Last active
September 21, 2022 10:29
-
-
Save manchoz/84fb59491189da451173f2044535466b to your computer and use it in GitHub Desktop.
X8 USB-C Logs
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| U-Boot SPL 2021.04+fio+gcdd676d7a3 (Feb 24 2022 - 18:19:51 +0000) | |
| power_bd71837_init | |
| Turn on SE050 | |
| DDRINFO: start DRAM init | |
| DDRINFO: DRAM rate 3000MTS | |
| DDRINFO:ddrphy calibration done | |
| DDRINFO: ddrmix config done | |
| Normal Boot | |
| Trying to boot from MMC2 | |
| SPL: Booting primary boot path: using 0x300 offset for next boot image | |
| ## Checking hash(es) for config config-1 ... sha256,rsa2048:ubootdev+ OK | |
| ## Checking hash(es) for Image atf ... sha256+ OK | |
| ## Checking hash(es) for Image uboot ... sha256+ OK | |
| ## Checking hash(es) for Image ubootfdt ... sha256+ OK | |
| ## Checking hash(es) for Image optee ... sha256+ OK | |
| ## Checking hash(es) for Image bootscr ... sha256+ OK | |
| NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-0-g2a2678646-dirty | |
| NOTICE: BL31: Built : 06:45:33, Mar 26 2021 | |
| I/TC: | |
| I/TC: Non-secure external DT found | |
| I/TC: OP-TEE version: 3.10.0-106-g60c991793 (gcc version 10.2.0 (GCC)) #1 Tue 29 Jun 2021 07:05:04 PM UTC aarch64 | |
| I/TC: Primary CPU initializing | |
| I/TC: Primary CPU switching to normal world boot | |
| U-Boot 2021.04+fio+gcdd676d7a3 (Feb 24 2022 - 18:19:51 +0000) | |
| CPU: i.MX8MMQ rev1.0 1600 MHz (running at 1200 MHz) | |
| CPU: Industrial temperature grade (-40C to 105C) at 50C | |
| Reset cause: POR | |
| Model: Arduino Portenta X8 i.MX8MM board | |
| Watchdog enabled | |
| DRAM: 2 GiB | |
| setup_iomux_fec | |
| anx7625_probe: start | |
| anx7625_setup | |
| anx7625_power_on | |
| anx7625_config | |
| anx7625_ocm_loading_check | |
| anx7625_setup: OCM started | |
| anx7625_disable_auto_rdo | |
| anx7625_enable_auto_rdo | |
| anx7625_setup: chip init registers succeeded. | |
| Driver ver 0.1.04-uboot | |
| Firmware ver 1300 | |
| Request: | |
| Voltage Max 5 [V] | |
| Power Min 5V @ 900 [mA] | |
| Power Max 5V @ 3000 [mA] | |
| Begin Negotiation: | |
| anx7625_negotiate_pd: count:0 | |
| INT: CC STATUS CHANGE | |
| CC1: SRC.Open | |
| CC2: SNK.Power1.5 | |
| anx7625_negotiate_pd: count:1 | |
| anx7625_negotiate_pd: count:2 | |
| INT: POWER NEGOTIATION FINISHED | |
| Voltage: 5 [V] | |
| Power: 5V @ 600 [mA] | |
| Power negotiation failure (5V @ 600 [mA] below min setting 5V @ 900 [mA]) | |
| Please change power adapter and/or USB-C hub and retry. |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| U-Boot SPL 2021.04+fio+gcdd676d7a3 (Feb 24 2022 - 18:19:51 +0000) | |
| power_bd71837_init | |
| Turn on SE050 | |
| DDRINFO: start DRAM init | |
| DDRINFO: DRAM rate 3000MTS | |
| DDRINFO:ddrphy calibration done | |
| DDRINFO: ddrmix config done | |
| Normal Boot | |
| Trying to boot from MMC2 | |
| SPL: Booting primary boot path: using 0x300 offset for next boot image | |
| ## Checking hash(es) for config config-1 ... sha256,rsa2048:ubootdev+ OK | |
| ## Checking hash(es) for Image atf ... sha256+ OK | |
| ## Checking hash(es) for Image uboot ... sha256+ OK | |
| ## Checking hash(es) for Image ubootfdt ... sha256+ OK | |
| ## Checking hash(es) for Image optee ... sha256+ OK | |
| ## Checking hash(es) for Image bootscr ... sha256+ OK | |
| NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-0-g2a2678646-dirty | |
| NOTICE: BL31: Built : 06:45:33, Mar 26 2021 | |
| I/TC: | |
| I/TC: Non-secure external DT found | |
| I/TC: OP-TEE version: 3.10.0-106-g60c991793 (gcc version 10.2.0 (GCC)) #1 Tue 29 Jun 2021 07:05:04 PM UTC aarch64 | |
| I/TC: Primary CPU initializing | |
| I/TC: Primary CPU switching to normal world boot | |
| U-Boot 2021.04+fio+gcdd676d7a3 (Feb 24 2022 - 18:19:51 +0000) | |
| CPU: i.MX8MMQ rev1.0 1600 MHz (running at 1200 MHz) | |
| CPU: Industrial temperature grade (-40C to 105C) at 35C | |
| Reset cause: POR | |
| Model: Arduino Portenta X8 i.MX8MM board | |
| Watchdog enabled | |
| DRAM: 2 GiB | |
| setup_iomux_fec | |
| anx7625_probe: start | |
| anx7625_setup | |
| anx7625_power_on | |
| anx7625_config | |
| anx7625_ocm_loading_check | |
| anx7625_setup: OCM started | |
| anx7625_disable_auto_rdo | |
| anx7625_enable_auto_rdo | |
| anx7625_setup: chip init registers succeeded. | |
| Driver ver 0.1.04-uboot | |
| Firmware ver 1300 | |
| Request: | |
| Voltage Max 5 [V] | |
| Power Min 5V @ 900 [mA] | |
| Power Max 5V @ 3000 [mA] | |
| Begin Negotiation: | |
| anx7625_negotiate_pd: count:0 | |
| INT: CC STATUS CHANGE | |
| CC1: SRC.Open | |
| CC2: SNK.Power1.5 | |
| anx7625_negotiate_pd: count:1 | |
| anx7625_negotiate_pd: count:2 | |
| INT: POWER NEGOTIATION FINISHED | |
| Voltage: 5 [V] | |
| Power: 5V @ 100 [mA] | |
| Power negotiation failure (5V @ 100 [mA] below min setting 5V @ 900 [mA]) | |
| Please change power adapter and/or USB-C hub and retry. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment