ESR600H Openwrt master firstboot

boot.log

U-boot Ver:1.0.6.198 2012/02/16


Board: Ralink APSoC DRAM:  64 MB
spi_wait_nsec: 48
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.raspi_read: from:30000 len:1000
.============================================
ASIC 3883_MP (MAC to GigaPHY Mode)
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

Please choose the operation:
   1: Load system code to SDRAM via TFTP.


3: System Boot system code via Flash.
raspi_read: from:50000 len:40
.raspi_read: from:50040 len:16810f
.......................

OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <[email protected]>
Decompressing kernel... done!
Starting kernel at 80000000...

[    0.000000] Linux version 5.4.81 (pi@SDDesk) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13719+1411-66e04abbb6)) #0 Mon Dec 7 08:54:16 2020
[    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] MIPS: machine is EnGenius ESR600H
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 59144K/65536K available (3632K kernel code, 173K rwdata, 540K rodata, 1216K init, 186K bss, 6392K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from 0x804409ac with crng_init=0
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.015483] Calibrating delay loop... 249.34 BogoMIPS (lpj=498688)
[    0.059626] pid_max: default: 32768 minimum: 301
[    0.068991] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.083403] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.104788] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.124093] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.137624] pinctrl core: initialized pinctrl subsystem
[    0.148679] NET: Registered protocol family 16
[    0.162918] rt3883-pci 10140000.pci: mode: PCIe
[    1.117190] random: fast init done
[    1.792713] PCI host bridge /pci@10140000/pci@0 ranges:
[    1.802996]  MEM 0x0000000020000000..0x000000002fffffff
[    1.813350]   IO 0x0000000010160000..0x000000001016ffff
[    1.846341] rt2880_gpio 10000600.gpio: registering 24 gpios
[    1.857396] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    1.870108] rt2880_gpio 10000638.gpio: registering 16 gpios
[    1.882197] PCI host bridge to bus 0000:00
[    1.890264] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.903878] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.915645] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.929143] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.945076] pci 0000:00:01.0: [1814:0802] type 01 class 0x060400
[    1.956934] pci 0000:00:01.0: reg 0x14: [mem 0x20100000-0x2010ffff]
[    1.969415] pci 0000:00:01.0: supports D1
[    1.977306] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    1.990776] pci 0000:01:00.0: [1814:3091] type 00 class 0x028000
[    2.002686] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[    2.015180] pci 0000:01:00.0: PME# supported from D0 D3hot
[    2.027796] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.040865] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    2.054009] pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    2.067479] pci 0000:00:01.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
[    2.080984] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
[    2.094478] pci 0000:00:01.0: PCI bridge to [bus 01]
[    2.104339] pci 0000:00:01.0:   bridge window [mem 0x20000000-0x200fffff]
[    2.117982] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    2.143482] clocksource: Switched to clocksource MIPS
[    2.155003] NET: Registered protocol family 2
[    2.164583] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    2.181161] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    2.196331] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    2.210342] TCP: Hash tables configured (established 1024 bind 1024)
[    2.223163] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    2.236090] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    2.250260] NET: Registered protocol family 1
[    2.258909] PCI: CLS 0 bytes, default 32
[    2.270422] rt-timer 10000100.timer: maximum frequency is 5065Hz
[    2.285036] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    2.305751] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.317267] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.354753] gpio-export gpio_export: 1 gpio(s) exported
[    2.365435] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    2.379378] printk: console [ttyS0] disabled
[    2.387869] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    2.407520] printk: console [ttyS0] enabled
[    2.407520] printk: console [ttyS0] enabled
[    2.424083] printk: bootconsole [early0] disabled
[    2.424083] printk: bootconsole [early0] disabled
[    2.451783] spi spi0.0: force spi mode3
[    2.460590] spi-nor spi0.0: mx25l6405d (8192 Kbytes)
[    2.470624] 5 fixed-partitions partitions found on MTD device spi0.0
[    2.483302] Creating 5 MTD partitions on "spi0.0":
[    2.492883] 0x000000000000-0x000000030000 : "u-boot"
[    2.504062] 0x000000030000-0x000000031000 : "u-boot-env"
[    2.515984] 0x000000032000-0x000000040000 : "config"
[    2.527079] 0x000000040000-0x000000050000 : "factory"
[    2.538376] 0x000000050000-0x000000800000 : "firmware"
[    2.555124] 2 uimage-fw partitions found on MTD device firmware
[    2.567000] Creating 2 MTD partitions on "firmware":
[    2.576918] 0x000000000000-0x00000016814f : "kernel"
[    2.588086] 0x00000016814f-0x0000007b0000 : "rootfs"
[    2.599119] mtd: device 6 (rootfs) set to be root filesystem
[    2.612763] 1 squashfs-split partitions found on MTD device rootfs
[    2.625173] 0x00000045e000-0x0000007b0000 : "rootfs_data"
[    2.638280] libphy: Fixed MDIO Bus: probed
[    2.650240] mtk_soc_eth 10100000.ethernet: generated random MAC address 9e:50:91:9a:42:58
[    2.666835] libphy: mdio: probed
[    2.675841] switch0: Atheros AR8327 rev. 2 switch registered on mdio-bus
[    3.265905] mtk_soc_eth 10100000.ethernet: connected port 0 to PHY at mdio-bus:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316]
[    3.290689] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    3.307903] rt2880_wdt 10000120.watchdog: Initialized
[    3.319860] NET: Registered protocol family 10
[    3.334341] Segment Routing with IPv6
[    3.341902] NET: Registered protocol family 17
[    3.350864] 8021q: 802.1Q VLAN Support v1.8
[    3.372095] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    3.395094] Freeing unused kernel memory: 1216K
[    3.404154] This architecture does not have kernel memory protection.
[    3.416990] Run /sbin/init as init process
[    6.122921] init: Console is alive
[    6.130184] init: - watchdog -
[    8.124103] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.532868] usbcore: registered new interface driver usbfs
[    8.544016] usbcore: registered new interface driver hub
[    8.554793] usbcore: registered new device driver usb
[    8.568619] gpio-keys keys: failed to get irq for gpio:26
[    8.584273] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.607790] SCSI subsystem initialized
[    8.622433] ehci-fsl: Freescale EHCI Host controller driver
[    8.636147] ehci-platform: EHCI generic platform driver
[    8.657056] phy phy-usbphy.0: remote usb device wakeup disabled
[    8.668874] phy phy-usbphy.0: UTMI 16bit 30MHz
[    8.677741] ehci-platform 101c0000.ehci: EHCI Host Controller
[    8.689261] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    8.705217] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    8.731505] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    8.745244] hub 1-0:1.0: USB hub found
[    8.753338] hub 1-0:1.0: 2 ports detected
[    8.768929] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    8.783127] ohci-platform: OHCI generic platform driver
[    8.793961] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    8.807584] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    8.823530] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    8.900725] hub 2-0:1.0: USB hub found
[    8.908817] hub 2-0:1.0: 2 ports detected
[    8.927645] usbcore: registered new interface driver usb-storage
[    8.940483] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.965553] init: - preinit -
[   11.505859] random: jshn: uninitialized urandom read (4 bytes read)
[   11.627621] random: jshn: uninitialized urandom read (4 bytes read)
[   11.990559] random: jshn: uninitialized urandom read (4 bytes read)
[   14.042494] 8021q: adding VLAN 0 to HW filter on device eth0
[   14.054590] Atheros AR8216/AR8236/AR8316 mdio-bus:00: Port 1 is up
[   14.067507] mtk_soc_eth 10100000.ethernet eth0: link up (1000Mbps/Full duplex)
[   14.095603] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   14.123706] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   14.201666] urandom_read: 2 callbacks suppressed
[   14.201677] random: procd: uninitialized urandom read (4 bytes read)
[   18.966675] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   18.986018] urandom-seed: Seed file not found (/etc/urandom.seed)
[   19.038558] mtk_soc_eth 10100000.ethernet eth0: link down
[   19.075801] procd: - early -
[   19.081775] procd: - watchdog -
[   20.402868] procd: - watchdog -
[   20.409981] procd: - ubus -
[   20.852465] random: ubusd: uninitialized urandom read (4 bytes read)
[   20.867332] random: ubusd: uninitialized urandom read (4 bytes read)
[   20.880805] random: ubusd: uninitialized urandom read (4 bytes read)
[   20.895155] procd: - init -
Please press Enter to activate this console.
[   22.581351] kmodloader: loading kernel modules from /etc/modules.d/*
[   22.659546] Loading modules backported from Linux version v5.8-0-gbcf876870b95
[   22.673971] Backport generated by backports.git v5.8-1-0-g79400d9e
[   22.771635] xt_time: kernel timezone is -0000
[   22.887217] urngd: v1.0.2 started.
[   22.963725] PPP generic driver version 2.4.2
[   22.985481] NET: Registered protocol family 24
[   23.094896] rt2800pci 0000:01:00.0: enabling device (0000 -> 0002)
[   23.123503] rt2800pci 0000:01:00.0: loaded eeprom from mtd device "factory"
[   23.137417] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[   23.152915] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5392 detected
[   23.279762] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[   23.294234] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3883, rev 0400 detected
[   23.309716] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 3853 detected
[   23.372613] random: crng init done
[   23.379446] random: 1 urandom warning(s) missed due to ratelimiting
[   23.731768] kmodloader: done loading kernel modules from /etc/modules.d/*
[   85.144825] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   85.187786] jffs2_build_filesystem(): unlocking the mtd device...
[   85.187795] done.
[   85.203996] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   86.169969] 8021q: adding VLAN 0 to HW filter on device eth0
[   86.197074] mtk_soc_eth 10100000.ethernet eth0: link up (1000Mbps/Full duplex)
[   86.243596] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   86.304318] device eth0 entered promiscuous mode
[   86.359453] br-lan: port 1(eth0.1) entered blocking state
[   86.370311] br-lan: port 1(eth0.1) entered disabled state
[   86.381562] device eth0.1 entered promiscuous mode
[   86.497180] br-lan: port 1(eth0.1) entered blocking state
[   86.507995] br-lan: port 1(eth0.1) entered forwarding state
[   87.168172] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  127.770962] done.
[  127.774865] jffs2: notice: (1854) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  128.090183] overlayfs: upper fs does not support tmpfile.