mcprat · October 13, 2020 03:23
diff --git a/boot.log b/boot.log
 [    0.000000] Linux version 5.4.69 (pi@SDDesk) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13719+835-66e04abbb6)) #0 Sat Oct 10 02:41:39 2020
 [    0.000000] printk: bootconsole [early0] enabled
 [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
 [    0.000000] MIPS: machine is EnGenius EAP600
 [    0.000000] SoC: Atheros AR9344 rev 2
 [    0.000000] Initrd not found or empty - disabling initrd
 [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
 [    0.000000] Zone ranges:
 [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
 [    0.000000] Movable zone start for each node
 [    0.000000] Early memory node ranges
 [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
 [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
 [    0.000000] On node 0 totalpages: 32768
 [    0.000000]   Normal zone: 288 pages used for memmap
 [    0.000000]   Normal zone: 0 pages reserved
 [    0.000000]   Normal zone: 32768 pages, LIFO batch:7
 [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 [    0.000000] pcpu-alloc: [0] 0 
 [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
 [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
 [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
 [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
 [    0.000000] Writing ErrCtl register=00000000
 [    0.000000] Readback ErrCtl register=00000000
 [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
 [    0.000000] Memory: 122256K/131072K available (4770K kernel code, 190K rwdata, 1104K rodata, 1224K init, 196K bss, 8816K reserved, 0K cma-reserved)
 [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
 [    0.000000] NR_IRQS: 51
 [    0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0
 [    0.000000] CPU clock: 560.000 MHz
 [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
 [    0.000009] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
 [    0.008304] Calibrating delay loop... 278.78 BogoMIPS (lpj=557568)
 [    0.050867] pid_max: default: 32768 minimum: 301
 [    0.055946] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 [    0.063744] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 [    0.077002] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
 [    0.087418] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
 [    0.094788] pinctrl core: initialized pinctrl subsystem
 [    0.101397] NET: Registered protocol family 16
 [    0.136625] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
 [    0.150337] clocksource: Switched to clocksource MIPS
 [    0.156970] NET: Registered protocol family 2
 [    0.162537] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
 [    0.171502] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
 [    0.179677] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
 [    0.187193] TCP: Hash tables configured (established 1024 bind 1024)
 [    0.194091] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
 [    0.201104] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
 [    0.208828] NET: Registered protocol family 1
 [    0.213541] PCI: CLS 0 bytes, default 32
 [    0.221676] workingset: timestamp_bits=14 max_order=15 bucket_order=1
 [    0.235646] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 [    0.241903] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 [    0.269020] pinctrl-single 1804002c.pinmux: 544 pins, size 68
 [    0.276194] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
 [    0.283730] printk: console [ttyS0] disabled
 [    0.288375] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
 [    0.297577] printk: console [ttyS0] enabled
 [    0.306479] printk: bootconsole [early0] disabled
 [    0.323497] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
 [    0.328840] 9 fixed-partitions partitions found on MTD device spi0.0
 [    0.335302] Creating 9 MTD partitions on "spi0.0":
 [    0.340183] 0x000000000000-0x000000040000 : "u-boot"
 [    0.346248] 0x000000040000-0x000000050000 : "u-boot-env"
 [    0.352618] 0x000000050000-0x0000000a0000 : "custom"
 [    0.358753] 0x0000000a0000-0x0000000b0000 : "loader"
 [    0.364774] 0x0000000b0000-0x000000220000 : "firmware2"
 [    0.371121] 0x000000220000-0x000000230000 : "fakeroot"
 [    0.377326] 0x000000230000-0x000000df0000 : "firmware1"
 [    0.383639] 0x000000df0000-0x000000ff0000 : "failsafe"
 [    0.389867] 0x000000ff0000-0x000001000000 : "art"
 [    0.395898] Concatenating MTD devices:
 [    0.399764] (0): "firmware1"
 [    0.402696] (1): "firmware2"
 [    0.405611] into device "virtual_flash"
 [    0.409549] 1 fixed-partitions partitions found on MTD device virtual_flash
 [    0.416620] Creating 1 MTD partitions on "virtual_flash":
 [    0.422119] 0x000000000000-0x000000d30000 : "firmware"
 [    0.437606] 2 okli-fw partitions found on MTD device firmware
 [    0.443499] Creating 2 MTD partitions on "firmware":
 [    0.448557] 0x000000000000-0x0000001f0000 : "kernel"
 [    0.454600] 0x0000001f0000-0x000000d30000 : "rootfs"
 [    0.460587] mtd: device 11 (rootfs) set to be root filesystem
 [    0.468360] 1 squashfs-split partitions found on MTD device rootfs
 [    0.474702] 0x000000510000-0x000000d30000 : "rootfs_data"
 [    0.483089] libphy: Fixed MDIO Bus: probed
 [    0.820258] libphy: ag71xx_mdio: probed
 [    0.826395] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd072, driver=Atheros 8035 ethernet]
 [    0.836944] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii-id
 [    0.843755] i2c /dev entries driver
 [    0.849568] NET: Registered protocol family 10
 [    0.859614] Segment Routing with IPv6
 [    0.863515] NET: Registered protocol family 17
 [    0.868118] 8021q: 802.1Q VLAN Support v1.8
 [    0.873346] PCI host bridge /ahb/pcie-controller@180c0000 ranges:
 [    0.879617]  MEM 0x0000000010000000..0x0000000013ffffff
 [    0.884938]   IO 0x0000000000000000..0x0000000000000000
 [    0.890460] PCI host bridge to bus 0000:00
 [    0.894660] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
 [    0.901653] pci_bus 0000:00: root bus resource [io  0x0000]
 [    0.907319] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
 [    0.914217] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 [    0.922309] pci 0000:00:00.0: [168c:0030] type 00 class 0x028000
 [    0.928478] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
 [    0.935423] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
 [    0.942316] pci 0000:00:00.0: supports D1
 [    0.946417] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
 [    0.953532] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
 [    0.960307] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
 [    0.967769] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
 [    0.980943] VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
 [    0.993762] Freeing unused kernel memory: 1224K
 [    0.998394] This architecture does not have kernel memory protection.
 [    1.004930] Run /sbin/init as init process
 [    1.198348] random: fast init done
 [    1.621906] init: Console is alive
 [    1.625662] init: - watchdog -
 [    2.499160] kmodloader: loading kernel modules from /etc/modules-boot.d/*
 [    2.672990] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
 [    2.690838] init: - preinit -
 [    3.901012] random: jshn: uninitialized urandom read (4 bytes read)
 [    4.045562] random: jshn: uninitialized urandom read (4 bytes read)
 [    4.088922] random: jshn: uninitialized urandom read (4 bytes read)
 [    7.375737] eth0: link up (1000Mbps/Full duplex)
 [    7.380570] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 [    8.529180] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
 [    8.536558] jffs2_build_filesystem(): unlocking the mtd device... 
 [    8.536564] done.
 [    8.544793] jffs2_build_filesystem(): erasing all blocks after the end marker... 
 [   51.418397] random: crng init done
 [   51.429439] random: 5 urandom warning(s) missed due to ratelimiting
 [   63.629020] done.
 [   63.631036] jffs2: notice: (528) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 [   63.648346] mount_root: overlay filesystem has not been fully initialized yet
 [   63.656615] mount_root: switching to jffs2 overlay
 [   63.685011] overlayfs: upper fs does not support tmpfile.
 [   63.695157] urandom-seed: Seed file not found (/etc/urandom.seed)
 [   63.811377] eth0: link down
 [   63.827939] procd: - early -
 [   63.831044] procd: - watchdog -
 [   64.482457] procd: - watchdog -
 [   64.485976] procd: - ubus -
 [   64.796938] procd: - init -
 [   65.677069] kmodloader: loading kernel modules from /etc/modules.d/*
 [   65.962511] Loading modules backported from Linux version v5.8-0-gbcf876870b95
 [   65.969883] Backport generated by backports.git v5.8-1-0-g79400d9e
 [   66.031919] xt_time: kernel timezone is -0000
 [   66.144895] urngd: v1.0.2 started.
 [   66.189668] PPP generic driver version 2.4.2
 [   66.203881] NET: Registered protocol family 24
 [   66.312495] ath: EEPROM regdomain sanitized
 [   66.312507] ath: EEPROM regdomain: 0x64
 [   66.312512] ath: EEPROM indicates we should expect a direct regpair map
 [   66.312535] ath: Country alpha2 being used: 00
 [   66.312539] ath: Regpair used: 0x64
 [   66.325884] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
 [   66.328163] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=12
 [   66.335277] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
 [   66.341818] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
 [   66.352120] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin
 [   68.510755] ath: EEPROM regdomain sanitized
 [   68.510766] ath: EEPROM regdomain: 0x64
 [   68.510771] ath: EEPROM indicates we should expect a direct regpair map
 [   68.510794] ath: Country alpha2 being used: 00
 [   68.510798] ath: Regpair used: 0x64
 [   68.521215] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
 [   68.523589] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=14
 [   68.558003] kmodloader: done loading kernel modules from /etc/modules.d/*
 [   98.434670] br-lan: port 1(eth0) entered blocking state
 [   98.440029] br-lan: port 1(eth0) entered disabled state
 [   98.445685] device eth0 entered promiscuous mode
 [  101.487730] eth0: link up (1000Mbps/Full duplex)
 [  101.492658] br-lan: port 1(eth0) entered blocking state
 [  101.497994] br-lan: port 1(eth0) entered forwarding state
 [  101.505936] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
	[ 0.000000] Linux version 5.4.69 (pi@SDDesk) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13719+835-66e04abbb6)) #0 Sat Oct 10 02:41:39 2020
	[ 0.000000] printk: bootconsole [early0] enabled
	[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
	[ 0.000000] MIPS: machine is EnGenius EAP600
	[ 0.000000] SoC: Atheros AR9344 rev 2
	[ 0.000000] Initrd not found or empty - disabling initrd
	[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
	[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
	[ 0.000000] Zone ranges:
	[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
	[ 0.000000] Movable zone start for each node
	[ 0.000000] Early memory node ranges
	[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
	[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
	[ 0.000000] On node 0 totalpages: 32768
	[ 0.000000] Normal zone: 288 pages used for memmap
	[ 0.000000] Normal zone: 0 pages reserved
	[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
	[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
	[ 0.000000] pcpu-alloc: [0] 0
	[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
	[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
	[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
	[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
	[ 0.000000] Writing ErrCtl register=00000000
	[ 0.000000] Readback ErrCtl register=00000000
	[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
	[ 0.000000] Memory: 122256K/131072K available (4770K kernel code, 190K rwdata, 1104K rodata, 1224K init, 196K bss, 8816K reserved, 0K cma-reserved)
	[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
	[ 0.000000] NR_IRQS: 51
	[ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0
	[ 0.000000] CPU clock: 560.000 MHz
	[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
	[ 0.000009] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
	[ 0.008304] Calibrating delay loop... 278.78 BogoMIPS (lpj=557568)
	[ 0.050867] pid_max: default: 32768 minimum: 301
	[ 0.055946] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
	[ 0.063744] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
	[ 0.077002] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
	[ 0.087418] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
	[ 0.094788] pinctrl core: initialized pinctrl subsystem
	[ 0.101397] NET: Registered protocol family 16
	[ 0.136625] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
	[ 0.150337] clocksource: Switched to clocksource MIPS
	[ 0.156970] NET: Registered protocol family 2
	[ 0.162537] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
	[ 0.171502] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
	[ 0.179677] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
	[ 0.187193] TCP: Hash tables configured (established 1024 bind 1024)
	[ 0.194091] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
	[ 0.201104] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
	[ 0.208828] NET: Registered protocol family 1
	[ 0.213541] PCI: CLS 0 bytes, default 32
	[ 0.221676] workingset: timestamp_bits=14 max_order=15 bucket_order=1
	[ 0.235646] squashfs: version 4.0 (2009/01/31) Phillip Lougher
	[ 0.241903] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
	[ 0.269020] pinctrl-single 1804002c.pinmux: 544 pins, size 68
	[ 0.276194] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
	[ 0.283730] printk: console [ttyS0] disabled
	[ 0.288375] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
	[ 0.297577] printk: console [ttyS0] enabled
	[ 0.306479] printk: bootconsole [early0] disabled
	[ 0.323497] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
	[ 0.328840] 9 fixed-partitions partitions found on MTD device spi0.0
	[ 0.335302] Creating 9 MTD partitions on "spi0.0":
	[ 0.340183] 0x000000000000-0x000000040000 : "u-boot"
	[ 0.346248] 0x000000040000-0x000000050000 : "u-boot-env"
	[ 0.352618] 0x000000050000-0x0000000a0000 : "custom"
	[ 0.358753] 0x0000000a0000-0x0000000b0000 : "loader"
	[ 0.364774] 0x0000000b0000-0x000000220000 : "firmware2"
	[ 0.371121] 0x000000220000-0x000000230000 : "fakeroot"
	[ 0.377326] 0x000000230000-0x000000df0000 : "firmware1"
	[ 0.383639] 0x000000df0000-0x000000ff0000 : "failsafe"
	[ 0.389867] 0x000000ff0000-0x000001000000 : "art"
	[ 0.395898] Concatenating MTD devices:
	[ 0.399764] (0): "firmware1"
	[ 0.402696] (1): "firmware2"
	[ 0.405611] into device "virtual_flash"
	[ 0.409549] 1 fixed-partitions partitions found on MTD device virtual_flash
	[ 0.416620] Creating 1 MTD partitions on "virtual_flash":
	[ 0.422119] 0x000000000000-0x000000d30000 : "firmware"
	[ 0.437606] 2 okli-fw partitions found on MTD device firmware
	[ 0.443499] Creating 2 MTD partitions on "firmware":
	[ 0.448557] 0x000000000000-0x0000001f0000 : "kernel"
	[ 0.454600] 0x0000001f0000-0x000000d30000 : "rootfs"
	[ 0.460587] mtd: device 11 (rootfs) set to be root filesystem
	[ 0.468360] 1 squashfs-split partitions found on MTD device rootfs
	[ 0.474702] 0x000000510000-0x000000d30000 : "rootfs_data"
	[ 0.483089] libphy: Fixed MDIO Bus: probed
	[ 0.820258] libphy: ag71xx_mdio: probed
	[ 0.826395] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd072, driver=Atheros 8035 ethernet]
	[ 0.836944] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii-id
	[ 0.843755] i2c /dev entries driver
	[ 0.849568] NET: Registered protocol family 10
	[ 0.859614] Segment Routing with IPv6
	[ 0.863515] NET: Registered protocol family 17
	[ 0.868118] 8021q: 802.1Q VLAN Support v1.8
	[ 0.873346] PCI host bridge /ahb/pcie-controller@180c0000 ranges:
	[ 0.879617] MEM 0x0000000010000000..0x0000000013ffffff
	[ 0.884938] IO 0x0000000000000000..0x0000000000000000
	[ 0.890460] PCI host bridge to bus 0000:00
	[ 0.894660] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
	[ 0.901653] pci_bus 0000:00: root bus resource [io 0x0000]
	[ 0.907319] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
	[ 0.914217] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
	[ 0.922309] pci 0000:00:00.0: [168c:0030] type 00 class 0x028000
	[ 0.928478] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
	[ 0.935423] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
	[ 0.942316] pci 0000:00:00.0: supports D1
	[ 0.946417] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
	[ 0.953532] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
	[ 0.960307] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
	[ 0.967769] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
	[ 0.980943] VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
	[ 0.993762] Freeing unused kernel memory: 1224K
	[ 0.998394] This architecture does not have kernel memory protection.
	[ 1.004930] Run /sbin/init as init process
	[ 1.198348] random: fast init done
	[ 1.621906] init: Console is alive
	[ 1.625662] init: - watchdog -
	[ 2.499160] kmodloader: loading kernel modules from /etc/modules-boot.d/*
	[ 2.672990] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
	[ 2.690838] init: - preinit -
	[ 3.901012] random: jshn: uninitialized urandom read (4 bytes read)
	[ 4.045562] random: jshn: uninitialized urandom read (4 bytes read)
	[ 4.088922] random: jshn: uninitialized urandom read (4 bytes read)
	[ 7.375737] eth0: link up (1000Mbps/Full duplex)
	[ 7.380570] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
	[ 8.529180] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
	[ 8.536558] jffs2_build_filesystem(): unlocking the mtd device...
	[ 8.536564] done.
	[ 8.544793] jffs2_build_filesystem(): erasing all blocks after the end marker...
	[ 51.418397] random: crng init done
	[ 51.429439] random: 5 urandom warning(s) missed due to ratelimiting
	[ 63.629020] done.
	[ 63.631036] jffs2: notice: (528) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
	[ 63.648346] mount_root: overlay filesystem has not been fully initialized yet
	[ 63.656615] mount_root: switching to jffs2 overlay
	[ 63.685011] overlayfs: upper fs does not support tmpfile.
	[ 63.695157] urandom-seed: Seed file not found (/etc/urandom.seed)
	[ 63.811377] eth0: link down
	[ 63.827939] procd: - early -
	[ 63.831044] procd: - watchdog -
	[ 64.482457] procd: - watchdog -
	[ 64.485976] procd: - ubus -
	[ 64.796938] procd: - init -
	[ 65.677069] kmodloader: loading kernel modules from /etc/modules.d/*
	[ 65.962511] Loading modules backported from Linux version v5.8-0-gbcf876870b95
	[ 65.969883] Backport generated by backports.git v5.8-1-0-g79400d9e
	[ 66.031919] xt_time: kernel timezone is -0000
	[ 66.144895] urngd: v1.0.2 started.
	[ 66.189668] PPP generic driver version 2.4.2
	[ 66.203881] NET: Registered protocol family 24
	[ 66.312495] ath: EEPROM regdomain sanitized
	[ 66.312507] ath: EEPROM regdomain: 0x64
	[ 66.312512] ath: EEPROM indicates we should expect a direct regpair map
	[ 66.312535] ath: Country alpha2 being used: 00
	[ 66.312539] ath: Regpair used: 0x64
	[ 66.325884] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
	[ 66.328163] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=12
	[ 66.335277] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
	[ 66.341818] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
	[ 66.352120] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin
	[ 68.510755] ath: EEPROM regdomain sanitized
	[ 68.510766] ath: EEPROM regdomain: 0x64
	[ 68.510771] ath: EEPROM indicates we should expect a direct regpair map
	[ 68.510794] ath: Country alpha2 being used: 00
	[ 68.510798] ath: Regpair used: 0x64
	[ 68.521215] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
	[ 68.523589] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=14
	[ 68.558003] kmodloader: done loading kernel modules from /etc/modules.d/*
	[ 98.434670] br-lan: port 1(eth0) entered blocking state
	[ 98.440029] br-lan: port 1(eth0) entered disabled state
	[ 98.445685] device eth0 entered promiscuous mode
	[ 101.487730] eth0: link up (1000Mbps/Full duplex)
	[ 101.492658] br-lan: port 1(eth0) entered blocking state
	[ 101.497994] br-lan: port 1(eth0) entered forwarding state
	[ 101.505936] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready