Engenius EPG600 Openwrt firstboot (master-backport)

boot.log

## Booting image at bc060000 ...
   Image Name:   MIPS OpenWrt Linux-5.4.111
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    2000944 Bytes =  1.9 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
OK

Starting kernel ...



OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <[email protected]>
Decompressing kernel... done!
Starting kernel at 80000000...

[    0.000000] Linux version 5.4.111 (michael@Mark) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16053+6-f066ee2ad5)) #0 Fri Apr 30 05:01:57 2021
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is EnGenius EPG600
[    0.000000] User-defined physical RAM map overwrite
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000002ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000002ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000002ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 12180
[    0.000000] Kernel command line: console=ttyS0,115200 mem=48M rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=0001f644
[    0.000000] Readback ErrCtl register=0001f644
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 41196K/49152K available (4730K kernel code, 204K rwdata, 1048K rodata, 1176K init, 205K bss, 7956K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from start_kernel+0x308/0x4fc with crng_init=0
[    0.000000] CPU Clock: 600MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000010] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[    0.007591] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.045455] pid_max: default: 32768 minimum: 301
[    0.050143] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.057196] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.071697] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.081177] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.087862] pinctrl core: initialized pinctrl subsystem
[    0.093513] NET: Registered protocol family 16
[    0.360743] PCI host bridge /pcie@10140000 ranges:
[    0.365360]  MEM 0x0000000020000000..0x000000002fffffff
[    0.370419]   IO 0x0000000010160000..0x000000001016ffff
[    0.397690] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.403170] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.409520] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.414947] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.421276] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.426707] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.433044] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.438388] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.445137] PCI host bridge to bus 0000:00
[    0.449118] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.455740] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.461488] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.468080] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.475817] pci 0000:00:00.0: [1814:0802] type 01 class 0x060400
[    0.481643] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    0.487698] pci 0000:00:00.0: reg 0x14: [mem 0x20100000-0x2010ffff]
[    0.493867] pci 0000:00:00.0: supports D1
[    0.497691] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.505870] pci 0000:01:00.0: [1814:3091] type 00 class 0x028000
[    0.511732] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[    0.517902] pci 0000:01:00.0: PME# supported from D0 D3hot
[    0.525492] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.531897] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.538318] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    0.544712] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    0.551474] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    0.558067] pci 0000:00:00.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
[    0.564671] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
[    0.571258] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.576073] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    0.582790] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.598147] clocksource: Switched to clocksource systick
[    0.604678] NET: Registered protocol family 2
[    0.609756] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.617910] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.625320] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.632160] TCP: Hash tables configured (established 1024 bind 1024)
[    0.638475] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.644828] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.651895] NET: Registered protocol family 1
[    0.656187] PCI: CLS 80 bytes, default 32
[    0.662955] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.670963] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.685559] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.691227] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.718112] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.725503] printk: console [ttyS0] disabled
[    0.729724] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.739341] printk: console [ttyS0] enabled
[    0.739341] printk: console [ttyS0] enabled
[    0.747808] printk: bootconsole [early0] disabled
[    0.747808] printk: bootconsole [early0] disabled
[    0.763833] spi spi0.0: force spi mode3
[    0.768745] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[    0.774152] 7 fixed-partitions partitions found on MTD device spi0.0
[    0.780646] Creating 7 MTD partitions on "spi0.0":
[    0.785557] 0x000000000000-0x000000030000 : "u-boot"
[    0.791669] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.798236] 0x000000040000-0x000000050000 : "factory"
[    0.804385] 0x000000050000-0x000000060000 : "rf"
[    0.810219] 0x000000060000-0x000000fa0000 : "firmware"
[    0.820175] 2 uimage-fw partitions found on MTD device firmware
[    0.826297] Creating 2 MTD partitions on "firmware":
[    0.831389] 0x000000000000-0x0000001e8870 : "kernel"
[    0.837488] 0x0000001e8870-0x000000f40000 : "rootfs"
[    0.843579] mtd: device 6 (rootfs) set to be root filesystem
[    0.851119] 1 squashfs-split partitions found on MTD device rootfs
[    0.857524] 0x000000510000-0x000000f40000 : "rootfs_data"
[    0.864092] 0x000000fa0000-0x000000fb0000 : "backup"
[    0.870325] 0x000000fb0000-0x000001000000 : "storage"
[    0.877374] libphy: Fixed MDIO Bus: probed
[    0.891295] gsw: mdio mode enabled
[    0.894977] gsw: ephy base address: 10
[    0.902577] gsw: setting port4 to gmac mode
[    0.907236] libphy: mdio: probed
[    0.912893] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus
[    1.006893] random: fast init done
[    1.123845] mtk_soc_eth 10100000.ethernet: using fixed link parameters
[    1.130804] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    1.137607] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    1.146637] rt2880_wdt 10000120.watchdog: Initialized
[    1.153362] NET: Registered protocol family 10
[    1.162047] Segment Routing with IPv6
[    1.166018] NET: Registered protocol family 17
[    1.170646] 8021q: 802.1Q VLAN Support v1.8
[    1.182156] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    1.195783] Freeing unused kernel memory: 1176K
[    1.200436] This architecture does not have kernel memory protection.
[    1.207015] Run /sbin/init as init process
[    2.018007] init: Console is alive
[    2.021889] init: - watchdog -
[    3.376276] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.539233] usbcore: registered new interface driver usbfs
[    3.545005] usbcore: registered new interface driver hub
[    3.550580] usbcore: registered new device driver usb
[    3.558925] gpio-keys keys: does not support key code:360
[    3.568626] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.584553] SCSI subsystem initialized
[    3.594174] ehci-fsl: Freescale EHCI Host controller driver
[    3.602121] ehci-platform: EHCI generic platform driver
[    3.617904] phy phy-usbphy.0: remote usb device wakeup disabled
[    3.623963] phy phy-usbphy.0: UTMI 16bit 30MHz
[    3.628516] ehci-platform 101c0000.ehci: EHCI Host Controller
[    3.634426] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    3.642653] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    3.653149] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    3.660542] hub 1-0:1.0: USB hub found
[    3.664939] hub 1-0:1.0: 1 port detected
[    3.675002] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.682682] ohci-platform: OHCI generic platform driver
[    3.688412] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    3.695409] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    3.703626] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    3.735163] hub 2-0:1.0: USB hub found
[    3.739492] hub 2-0:1.0: 1 port detected
[    3.753176] usbcore: registered new interface driver usb-storage
[    3.760215] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.769266] init: - preinit -
[    5.317645] random: jshn: uninitialized urandom read (4 bytes read)
[    5.486388] random: jshn: uninitialized urandom read (4 bytes read)
[    6.002235] random: jshn: uninitialized urandom read (4 bytes read)
[    6.335000] urandom_read: 3 callbacks suppressed
[    6.335010] random: jshn: uninitialized urandom read (4 bytes read)
[    7.157112] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[    7.165719] 8021q: adding VLAN 0 to HW filter on device eth0
[    7.171949] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] ke[    7.230399] random: procd: uninitialized urandom read (4 bytes read)
y and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.565818] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.746070] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    8.757744] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.849310] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[    8.877182] procd: - early -
[    8.880428] procd: - watchdog -
[    9.186311] procd: - watchdog -
[    9.300656] procd: - ubus -
[    9.385799] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.395003] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.409647] procd: - init -
Please press Enter to activate this console.
[   10.540696] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.587919] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[   10.595747] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[   10.669383] xt_time: kernel timezone is -0000
[   10.940696] PPP generic driver version 2.4.2
[   10.953553] NET: Registered protocol family 24
[   11.044848] rt2800pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
[   11.056515] rt2800pci 0000:01:00.0: loaded eeprom from mtd device "factory"
[   11.063654] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
[   11.071602] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 000f detected
[   11.146028] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "rf"
[   11.153047] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   11.160992] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
[   11.224777] kmodloader: done loading kernel modules from /etc/modules.d/*
[   11.234813] urngd: jent-rng init failed, err: 2
[   21.546238] random: crng init done
[   45.926675] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   45.951497] jffs2_build_filesystem(): unlocking the mtd device...
[   45.951505] done.
[   45.959802] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   47.001026] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[   47.017079] 8021q: adding VLAN 0 to HW filter on device eth0
[   47.104592] Atheros AR8216/AR8236/AR8316 mdio-bus:00: Port 4 is up
[   47.111260] br-lan: port 1(eth0.1) entered blocking state
[   47.116800] br-lan: port 1(eth0.1) entered disabled state
[   47.122735] device eth0.1 entered promiscuous mode
[   47.127696] device eth0 entered promiscuous mode
[   47.236481] br-lan: port 1(eth0.1) entered blocking state
[   47.242038] br-lan: port 1(eth0.1) entered forwarding state
[   48.016674] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  117.074208] done.
[  117.076248] jffs2: notice: (2056) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  117.355101] overlayfs: upper fs does not support tmpfile.