Engenius ESR300 Openwrt firstboot

boot.log

U-boot Ver:1.0.5.8 2014/07/24 16:53:32


Board: Ralink APSoC DRAM:  64 MB
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 28
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
Flash size 16MB, sector count = 256
============================================
ASIC 7620_MP (Port5<->None)
Product Name: ESR300
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jul 24 2014  Time:16:53:32
============================================
EMBEDAD SWITH init

Please choose the operation:
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   9: Load Boot Loader code then write to Flash via TFTP.                                                                            0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-5.4.111
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    2000210 Bytes =  1.9 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
OK

Starting kernel ...



OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <[email protected]>
Decompressing kernel... done!
Starting kernel at 80000000...

[    0.000000] Linux version 5.4.111 (michael@Mark) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16053+6-f066ee2ad5)) #0 Sat May 8 02:35:16 2021
[    0.000000] Board has DDR1
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is EnGenius ESR300
[    0.000000] User-defined physical RAM map overwrite
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,115200 mem=64M rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=0007cfb4
[    0.000000] Readback ErrCtl register=0007cfb4
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 57452K/65536K available (4730K kernel code, 204K rwdata, 1048K rodata, 1176K init, 205K bss, 8084K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from start_kernel+0x308/0x4fc with crng_init=0
[    0.000000] CPU Clock: 600MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000010] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[    0.007585] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.045448] pid_max: default: 32768 minimum: 301
[    0.050132] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.057186] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.070346] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.079818] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.086504] pinctrl core: initialized pinctrl subsystem
[    0.092125] NET: Registered protocol family 16
[    0.128049] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.133508] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.139844] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.145270] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.151575] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.156993] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.163337] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.168679] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.175311] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.189844] clocksource: Switched to clocksource systick
[    0.196368] NET: Registered protocol family 2
[    0.201438] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.209588] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.216995] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.223837] TCP: Hash tables configured (established 1024 bind 1024)
[    0.230145] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.236496] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.243540] NET: Registered protocol family 1
[    0.247776] PCI: CLS 0 bytes, default 32
[    0.254358] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.262277] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.276779] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.282441] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.309128] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.316477] printk: console [ttyS0] disabled
[    0.320689] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.330304] printk: console [ttyS0] enabled
[    0.330304] printk: console [ttyS0] enabled
[    0.338773] printk: bootconsole [early0] disabled
[    0.338773] printk: bootconsole [early0] disabled
[    0.354654] spi spi0.0: force spi mode3
[    0.359509] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[    0.364873] 6 fixed-partitions partitions found on MTD device spi0.0
[    0.371372] Creating 6 MTD partitions on "spi0.0":
[    0.376283] 0x000000000000-0x000000030000 : "u-boot"
[    0.382444] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.388889] 0x000000040000-0x000000050000 : "factory"
[    0.395092] 0x000000050000-0x000000fa0000 : "firmware"
[    0.404342] 2 uimage-fw partitions found on MTD device firmware
[    0.410460] Creating 2 MTD partitions on "firmware":
[    0.415550] 0x000000000000-0x0000001e8592 : "kernel"
[    0.421644] 0x0000001e8592-0x000000f50000 : "rootfs"
[    0.427682] mtd: device 5 (rootfs) set to be root filesystem
[    0.435189] 1 squashfs-split partitions found on MTD device rootfs
[    0.441576] 0x000000540000-0x000000f50000 : "rootfs_data"
[    0.448095] 0x000000fa0000-0x000000fb0000 : "backup"
[    0.454281] 0x000000fb0000-0x000001000000 : "storage"
[    0.461356] libphy: Fixed MDIO Bus: probed
[    0.475906] gsw: setting port4 to ephy mode
[    0.480274] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link up (100Mbps/Full duplex)
[    0.490101] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.496876] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.505932] rt2880_wdt 10000120.watchdog: Initialized
[    0.512524] NET: Registered protocol family 10
[    0.520991] Segment Routing with IPv6
[    0.524938] NET: Registered protocol family 17
[    0.529561] 8021q: 802.1Q VLAN Support v1.8
[    0.541258] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.554952] Freeing unused kernel memory: 1176K
[    0.559607] This architecture does not have kernel memory protection.
[    0.566186] Run /sbin/init as init process
[    1.145784] random: fast init done
[    1.376739] init: Console is alive
[    1.380596] init: - watchdog -
[    2.720358] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.883074] usbcore: registered new interface driver usbfs
[    2.888833] usbcore: registered new interface driver hub
[    2.894388] usbcore: registered new device driver usb
[    2.906523] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.921969] SCSI subsystem initialized
[    2.931406] ehci-fsl: Freescale EHCI Host controller driver
[    2.939269] ehci-platform: EHCI generic platform driver
[    2.955017] phy phy-usbphy.0: remote usb device wakeup disabled
[    2.961075] phy phy-usbphy.0: UTMI 16bit 30MHz
[    2.965622] ehci-platform 101c0000.ehci: EHCI Host Controller
[    2.971539] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    2.979761] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    2.991464] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    2.998865] hub 1-0:1.0: USB hub found
[    3.003172] hub 1-0:1.0: 1 port detected
[    3.013019] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.020737] ohci-platform: OHCI generic platform driver
[    3.026444] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    3.033461] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    3.041665] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    3.073276] hub 2-0:1.0: USB hub found
[    3.077595] hub 2-0:1.0: 1 port detected
[    3.090214] usbcore: registered new interface driver usb-storage
[    3.097181] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.106060] init: - preinit -
[    4.641897] random: jshn: uninitialized urandom read (4 bytes read)
[    4.810182] random: jshn: uninitialized urandom read (4 bytes read)
[    5.222269] random: jshn: uninitialized urandom read (4 bytes read)
[    6.041597] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.115997] urandom_read: 4 callbacks suppressed
[    6.116006] random: procd: uninitialized urandom read (4 bytes read)
[    7.608229] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    7.619596] urandom-seed: Seed file not found (/etc/urandom.seed)
[    7.730276] procd: - early -
[    7.733498] procd: - watchdog -
[    8.028261] procd: - watchdog -
[    8.140163] procd: - ubus -
[    8.219573] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.228640] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.239275] procd: - init -
Please press Enter to activate this console.
[    9.339819] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.385821] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[    9.393643] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[    9.463441] xt_time: kernel timezone is -0000
[    9.730730] PPP generic driver version 2.4.2
[    9.743582] NET: Registered protocol family 24
[    9.827528] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[    9.834976] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[    9.842917] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[    9.906815] kmodloader: done loading kernel modules from /etc/modules.d/*
[   10.052831] urngd: jent-rng init failed, err: 2
[   19.671230] random: crng init done
[   28.597252] mtk_soc_eth 10100000.ethernet eth0: port 2 link down
[   30.765957] mtk_soc_eth 10100000.ethernet eth0: port 2 link up (100Mbps/Full duplex)
[   49.368700] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   49.391238] jffs2_build_filesystem(): unlocking the mtd device...
[   49.391245] done.
[   49.399537] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   50.420718] 8021q: adding VLAN 0 to HW filter on device eth0
[   50.489108] br-lan: port 1(eth0.1) entered blocking state
[   50.494720] br-lan: port 1(eth0.1) entered disabled state
[   50.500641] device eth0.1 entered promiscuous mode
[   50.505583] device eth0 entered promiscuous mode
[   50.599036] br-lan: port 1(eth0.1) entered blocking state
[   50.604621] br-lan: port 1(eth0.1) entered forwarding state
[   51.423806] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  119.844702] done.
[  119.846712] jffs2: notice: (1963) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  120.111699] overlayfs: upper fs does not support tmpfile.