ss-config.json

{
    "server":"0.0.0.0",
    "server_port":80,
    "password":"<PASSWORD>",
    "timeout":300,
    "method":"aes-256-gcm",
    "plugin":"v2ray-plugin",
    "plugin_opts":"server",
    "user":"nobody",
    "nameserver": "1.1.1.1",
    "fast_open":true,
    "reuse_port":true,
    "no_delay":true
}

{
    "server":"<DOMAIN>",
    "server_port":80,
    "local_address": "127.0.0.1",
    "local_port":4321,
    "password":"<PASSWORD>",
    "timeout":300,
    "method":"aes-256-gcm",
    "nameserver":"1.1.1.1",
    "mode":"tcp_and_udp",
    "fast_open": true,
    "plugin": "v2ray-plugin",
    "plugin_opts":"host=<DOMAIN>"
}

You should see Your SSL/TLS encryption mode is Full on your cloudflare panel for this configuration:

{
    "server":"0.0.0.0",
    "server_port":443,
    "password":"<PASSWORD>",
    "timeout":300,
    "user":"nobody",
    "nameserver": "1.1.1.1",
    "fast_open":true,
    "reuse_port":true,
    "no_delay":true,
    "method":"aes-256-gcm",
    "plugin":"v2ray-plugin",
    "plugin_opts":"server;tls;cert=/etc/letsencrypt/live/<DOMAIN>/fullchain.pem;key=/etc/letsencrypt/live/<DOMAIN>/privkey.pem;host=<DOMAIN>;loglevel=none"
}

ss-local:

{
    "server":"<DOMAIN>",
    "server_port":443,
    "local_address": "127.0.0.1",
    "local_port":4321,
    "password":"<PASSWORD>",
    "timeout":300,
    "method":"aes-256-gcm",
    "nameserver":"1.1.1.1",
    "mode":"tcp_and_udp",
    "fast_open": true,
    "plugin": "v2ray-plugin",
    "plugin_opts":"tls;host=<DOMAIN>"
}

AndroidClient:

[
  {
    "server": "<DODMAIN>",
    "server_port": 443,
    "password": "<PASSWORD>",
    "method": "aes-256-gcm",
    "plugin": "v2ray",
    "plugin_opts": "host=<DODMAIN>;tls",
    "remarks": "freedom",
    "route": "all",
    "remote_dns": "dns.google",
    "ipv6": false,
    "metered": false,
    "proxy_apps": {
      "enabled": false
    },
    "udpdns": false
  }
]

https://github.com/teddysun/across/raw/master/bbr.sh

root@freedom:~# cat /etc/sysctl.conf 
#
# /etc/sysctl.conf - Configuration file for setting system variables
# See /etc/sysctl.d/ for additional system variables.
# See sysctl.conf (5) for information.
#

#kernel.domainname = example.com

# Uncomment the following to stop low-level messages on console
#kernel.printk = 3 4 1 3

##############################################################3
# Functions previously found in netbase
#

# Uncomment the next two lines to enable Spoof protection (reverse-path filter)
# Turn on Source Address Verification in all interfaces to
# prevent some spoofing attacks
#net.ipv4.conf.default.rp_filter=1
#net.ipv4.conf.all.rp_filter=1

# Uncomment the next line to enable TCP/IP SYN cookies
# See http://lwn.net/Articles/277146/
# Note: This may impact IPv6 TCP sessions too
#net.ipv4.tcp_syncookies=1

# Uncomment the next line to enable packet forwarding for IPv4
#net.ipv4.ip_forward=1

# Uncomment the next line to enable packet forwarding for IPv6
#  Enabling this option disables Stateless Address Autoconfiguration
#  based on Router Advertisements for this host
#net.ipv6.conf.all.forwarding=1


###################################################################
# Additional settings - these settings can improve the network
# security of the host and prevent against some network attacks
# including spoofing attacks and man in the middle attacks through
# redirection. Some network environments, however, require that these
# settings are disabled so review and enable them as needed.
#
# Do not accept ICMP redirects (prevent MITM attacks)
#net.ipv4.conf.all.accept_redirects = 0
#net.ipv6.conf.all.accept_redirects = 0
# _or_
# Accept ICMP redirects only for gateways listed in our default
# gateway list (enabled by default)
# net.ipv4.conf.all.secure_redirects = 1
#
# Do not send ICMP redirects (we are not a router)
#net.ipv4.conf.all.send_redirects = 0
#
# Do not accept IP source route packets (we are not a router)
#net.ipv4.conf.all.accept_source_route = 0
#net.ipv6.conf.all.accept_source_route = 0
#
# Log Martian Packets
#net.ipv4.conf.all.log_martians = 1
#

###################################################################
# Magic system request Key
# 0=disable, 1=enable all, >1 bitmask of sysrq functions
# See https://www.kernel.org/doc/html/latest/admin-guide/sysrq.html
# for what other values do
#kernel.sysrq=438

fs.file-max = 51200

net.core.rmem_max = 67108864
net.core.wmem_max = 67108864
net.core.netdev_max_backlog = 250000
net.core.somaxconn = 4096

net.ipv4.tcp_syncookies = 1
net.ipv4.tcp_tw_reuse = 1
net.ipv4.tcp_fin_timeout = 30
net.ipv4.tcp_keepalive_time = 1200
net.ipv4.ip_local_port_range = 10000 65000
net.ipv4.tcp_max_syn_backlog = 8192
net.ipv4.tcp_max_tw_buckets = 5000
net.ipv4.tcp_fastopen = 3
net.ipv4.tcp_mem = 25600 51200 102400
net.ipv4.tcp_rmem = 4096 87380 67108864
net.ipv4.tcp_wmem = 4096 65536 67108864
net.ipv4.tcp_mtu_probing = 1
net.core.default_qdisc = fq
net.ipv4.tcp_congestion_control = bbr

root@freedom:~# cat /opt/ac/ufw.sh 
#!/usr/bin/bash
for ip in $(curl -qs https://www.arvancloud.com/fa/ips.txt); do ufw allow from $ip; done