blackmagic probe binaries for stlink v2 baite module

blackmagic.bin

blackmagic_dfu.bin

Blackmagicprobe_compile.md

## Tested the blue pill on 10/09/2018
## 1. install pre-requisites
sudo add-apt-repository ppa:team-gcc-arm-embedded/ppa
sudo apt update
sudo apt install gcc-arm-embedded
# If it reports error message of conflict to gcc-arm-none-eabi, which is likely if upgrading from 4.x to 5+, please uninstall it first with:
# "sudo apt-get remove gcc-arm-none-eabi"

sudo apt -y install lib32z1 lib32ncurses5 lib32bz2-1.0 

## 2. Build your blackmagic probe of choice
# Note: the reset --hard lines are optional.
# 		they are there to reference the exact commit the attached binary were built against

# blue pill: get the main blackmagic probe
git clone https://github.com/blacksphere/blackmagic.git
cd blackmagic
git reset --hard 3a598a0cf357a19065568435371096dc18948087 # blue pill - current as of 10/09/2018
git submodule init
git submodule update
make
cd src
make clean
make PROBE_HOST=stlink 
cd ../

# blue pill/baite: get and build UweBonnes baite branch
git clone https://github.com/UweBonnes/blackmagic.git UweBonnes_bmp
cd UweBonnes_bmp
git checkout baite
git reset --hard ef0d8e450018ad19d03aa4418412035ce4affb9f # baite - current as of 10/09/2018
git submodule init
git submodule update
make
cd src
make clean
make PROBE_HOST=stlink 
cd ../

# baite: get and build tsaitgaist baite-platform branch
git clone https://github.com/tsaitgaist/blackmagic.git tsaitgaist_bmp
cd tsaitgaist_bmp
git checkout baite-platform
git reset --hard 36a2e6ac1d9d270be5165366c8ff7a71267a8994 # baite - current as of 10/09/2018
git submodule init
git submodule update
make
cd src
make clean
make PROBE_HOST=baite
cd ../

# copy the created binaries
cp UweBonnes_bmp/src/blackmagic.bin UweBonnes.bin
cp UweBonnes_bmp/src/blackmagic_dfu.bin UweBonnes_dfu.bin
cp tsaitgaist_bmp/src/blackmagic.bin tsaitgaist.bin
cp tsaitgaist_bmp/src/blackmagic_dfu.bin tsaitgaist_dfu.bin
cp blackmagic/src/blackmagic.bin blackmagic.bin
cp blackmagic/src/blackmagic_dfu.bin blackmagic_dfu.bin

## 
# USB Tx -> A10, USB Rx -> A9
# BOOT0 = 1 (default is 0)
# BOOT1 = 0 # BOOT1 is the closest jumper to the reset button

# install the stm32flash utility
sudo apt install stm32flash

# disable flash read protection
stm32flash -k /dev/ttyUSB0
# disable flash write protection
stm32flash -u /dev/ttyUSB0
# erase flash
stm32flash -o /dev/ttyUSB0
# flash the DFU bootloader
stm32flash -w blackmagic_dfu.bin -v /dev/ttyUSB0
# disconnect the UART
# BOOT0 = 0 (default is 0)
# BOOT1 = 0 # BOOT1 is the closest jumper to the reset button
# flash the main firmware
# note : dfu-util will error out at the end if you try using that as the binary is greater than 64k.
# the stm32_mem.py doesnt care about this, so use that (theres enough space on the blue pill)
# see - https://github.com/blacksphere/blackmagic/blob/master/src/platforms/stlink/Flashsize_F103
sudo python2 blackmagic/scripts/stm32_mem.py blackmagic.bin
# reset device, smile

# For Arduino on linux:
# /dev/ttyACM0 = BMP programming port
# /dev/ttyACM1 = BMP UART port (Tx,Rx) = (A9,A10) on the bluepill
# Make sure you burn a bootloader (even if you select 'None' to erase it) prior to uploading your sketch!

tsaitgaist.bin

tsaitgaist_dfu.bin

UweBonnes.bin

UweBonnes_dfu.bin