Klipper Ender 5 Plus stock printer config

printer.cfg

# This file contains pin mappings for the Creality Ender 5 Plus.
# Ender 5 Plus stock uses a Creality v2.2 board, similar to CR-20 Pro.
# To use this config, the firmware should be compiled for the AVR atmega2560.

# See the example.cfg file for a description of available parameters.

[stepper_x]
step_pin: PF0
dir_pin: PF1
enable_pin: !PD7
step_distance: .0125
endstop_pin: ^PE5
position_endstop: 350
position_max: 350
homing_speed: 100

[stepper_y]
step_pin: PF6
dir_pin: PF7
enable_pin: !PF2
step_distance: .0125
endstop_pin: ^PJ1
position_endstop: 350
position_max: 350
homing_speed: 100

[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
step_distance: .001266
#step_distance: .0025
endstop_pin: probe:z_virtual_endstop
position_max: 400
position_min: -5 #set position_min to a negative value such as -5 when probing to set z offset, then revert to 0
homing_speed: 10.0

[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
step_distance: .010526
nozzle_diameter: 0.400
filament_diameter: 1.750
#pressure_advance: 0.617 # high value for stock long bowden tube, uncomment to enable pressure advance
#pressure_advance_smooth_time: 0.010 # uncomment to enable pressure advance
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK5
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 260

[safe_z_home]
home_xy_position: 180, 180
speed: 100
z_hop: 10 # Move up 10mm, so the probe doesnt hit anything 
z_hop_speed: 5

[bltouch]
sensor_pin: ^PD3
control_pin: PB5
x_offset: -45
y_offset: 0
#z_offset: 0
speed: 3.0
samples: 1
pin_up_reports_not_triggered: True
pin_up_touch_mode_reports_triggered: False

[bed_mesh]
speed: 100
horizontal_move_z: 8
mesh_min: 50, 50
mesh_max: 300,300
probe_count: 3,3 # 3,3 or 5,5
  
[gcode_macro G29]
gcode: 
  G28
  BED_MESH_CALIBRATE
  BED_MESH_PROFILE SAVE=p1
  G1 X0 Y0 Z5 F4000
  
[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: pid
pid_Kp: 690.34
pid_Ki: 111.47
pid_Kd: 1068.83
min_temp: 0
max_temp: 130

[fan]
pin: PH6

[mcu]
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000 # 20x print speed recommended
max_z_velocity: 5
max_z_accel: 100

#[display]
# Not sure this is supported for E5+

hey, mine just give me the error Klipper reports: ERROR

mcu 'mcu': Unable to connect
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Error configuring printer

hey, mine just give me the error Klipper reports: ERROR

mcu 'mcu': Unable to connect Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Error configuring printer

This may need updated, what main board and mcu are you using?

2.2v

@ssohail-droid Could be you need to change to whatever your pi is connected to
[mcu]
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0

I was able to get klipper on my Ender 5 Plus stock v2.2 board without a pi, using elementary OS 7 directly to the Ender, the only problem i am having is the Z probe crashing into the bed....it starts way above the bed. I read that the Ender is opposite than klipper? I noticed when i am leveling Z when i hit a negative # the bed goes down positive # the bed goes up?
Anybody else have this issue?