mohitbhoite

// This #include statement was automatically added by the Particle IDE.
#include "Adafruit_CCS811.h"

// This #include statement was automatically added by the Particle IDE.
#include <Adafruit_SSD1306_RK.h>

// #include <SPI.h>
// #include <Wire.h>
#include <Adafruit_GFX.h>
//SYSTEM_MODE(MANUAL);

mohitbhoite

#include <RTClib.h>
#include <Adafruit_DotStar.h>
#include <MAX7313.h>
#include "Wire.h"

#if defined(ARDUINO_ARCH_SAMD)
// for Zero, output on USB Serial console, remove line below if using programming port to program the Zero!
   #define Serial Serial
#endif

mohitbhoite

//
// Project link: https://www.bhoite.com/sculptures/surya-280/
//
#include <TinyBME280.h>
//#include <TinyWireM.h>
//#include <USI_TWI_Master.h>
#include <avr/sleep.h> //Needed for sleep_mode
#include <avr/wdt.h> //Needed to enable/disable watch dog timer
//Following is the header file for the LCD module bought on ebay
//Seller link https://www.ebay.com/itm/284843842249

mohitbhoite

//
// Project link: https://www.bhoite.com/sculptures/satellite-2202/
//
#include "Adafruit_SHT31.h"
//#include <TinyWireM.h>
//#include <USI_TWI_Master.h>
#include <avr/sleep.h> //Needed for sleep_mode
#include <avr/wdt.h> //Needed to enable/disable watch dog timer
//Following is the header file for the LCD module bought on ebay
//Seller link https://www.ebay.com/itm/284843842249

mohitbhoite

/*
 * ATtiny85 based VU meter
 * Author: Mohit Bhoite
 * Date: 01 August 2022
 * 
 * Based on original code by Adafruit Industries.  Distributed under the BSD license.
 * and David Johnson-Davies - www.technoblogy.com
 * CC BY 4.0 Licensed under a Creative Commons Attribution 4.0 International license: 
 * http://creativecommons.org/licenses/by/4.0/
 * 

mohitbhoite

#include <avr/sleep.h> //Needed for sleep_mode
#include <avr/wdt.h> //Needed to enable/disable watch dog timer

void setup() {
  pinMode(0, OUTPUT);// LED connected to pin 5 which is recognised as pin 0 by arduino
  ADCSRA &= ~(1<<ADEN); //Disable ADC, saves ~230uA
  //Power down various bits of hardware to lower power usage  
  set_sleep_mode(SLEEP_MODE_PWR_DOWN); //Power down everything, wake up from WDT
  sleep_enable();
}

mohitbhoite

/*********************************************************************
This is an example for our Monochrome OLEDs based on SSD1306 drivers

  Pick one up today in the adafruit shop!
  ------> http://www.adafruit.com/category/63_98

This example is for a 128x64 size display using I2C to communicate
3 pins are required to interface (2 I2C and one reset)

Adafruit invests time and resources providing this open source code, 

mohitbhoite

/* Function prototypes -------------------------------------------------------*/
int tinkerDigitalRead(String pin);
int tinkerDigitalWrite(String command);
int tinkerAnalogRead(String pin);
int tinkerAnalogWrite(String command);

/* This function is called once at start up ----------------------------------*/
void setup()
{
	//Setup the Tinker application here

mohitbhoite

#include <RTClib.h>

#include <Adafruit_DotStar.h>

#include <MAX7313.h>
#include "Wire.h"

#if defined(ARDUINO_ARCH_SAMD)
// for Zero, output on USB Serial console, remove line below if using programming port to program the Zero!
   #define Serial Serial

mohitbhoite

#include <Adafruit_NeoPixel.h>
int red,green,blue,white = 0;

// IMPORTANT: Set pixel COUNT, PIN and TYPE
#define PIN 4
#define NUMPIXELS 8

//Initialize the neopixel strip
Adafruit_NeoPixel strip(NUMPIXELS, PIN, NEO_RGBW + NEO_KHZ800);