Create Wi-Fi Hotspot on Linux using nmcli

create-hotspot.md

Create a Wi-Fi hotspot on Linux using nmcli

Original post : https://unix.stackexchange.com/a/310699

nmcli con add type wifi ifname wlan0 con-name Hostspot autoconnect yes ssid Hostspot
nmcli con modify Hostspot 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared
nmcli con modify Hostspot wifi-sec.key-mgmt wpa-psk
nmcli con modify Hostspot wifi-sec.psk "veryveryhardpassword1234"
nmcli con up Hostspot

Note

If after reboot nmcli con up Hotspot doesn't work

Use this command instead to start Hotspot

UUID=$(grep uuid /etc/NetworkManager/system-connections/Hotspot | cut -d= -f2)
nmcli con up uuid $UUID

All my experiments with this didnt work, i think this is because of the security type specified.
If you have the networkmanager applet in some way or another, for example the xfce one, then you can just create new network and then after making it if you want to start it a later time just do nmcli con up NETWORKNAME

Is there any shell scripts which could automate this.

I need a way to bundle it all up in a bash script, which I can just call once, to get me the ifname and create hotspot

I made one, it's very easy once you get to know the basics of shell. You'll need to know "read", variables, "case" if you want to get fancy, "echo", and obviously nmcli. For example, with a variable it would be nmcli con up $VARIABLENAME

@Blokheck011 that's the challenge, I'm not quite great with Shell scripting and It's a lot to put on hold, the wifi file sharing application I'm building, and go on learning shell, I need something I can plug and play

Plus, I still need to reimplement the solution in Rust

@CEMoreno @Blokheck011 This worked for me in when I was facing security type issue.

nmcli con modify Hotspot 802-11-wireless-security.pmf 1

Source: AskUbuntu

Error: Connection activation failed: No suitable device found for this connection (device enp12s0 not available because profile is not 
compatible with device (mismatching interface name)).

I have this error, when I try to up hotspot.

Please see: https://unix.stackexchange.com/a/760947/550161
Where i ask for a non-AP mode solution... 🤝

this is wep (very weak encryptions) how using WPA3 ?

I'm also trying to use same security type (WPA3) glad to know if you succeeded for it?

Thank you all, especially abhishekmj303 for this argument (802-11-wireless-security.pmf 1)

Excellent!
In some cases, you may need:

echo 1 > /proc/sys/net/ipv4/ip_forward
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE

reference on https://owlhowto.com/how-to-create-a-wifi-hotspot-on-debian-12/

using this to auto create hotspot on boot

nmcli con mod Hostspot connection.autoconnect yes

reference on https://owlhowto.com/how-to-create-a-wifi-hotspot-on-debian-12/

using this to auto create hotspot on boot

nmcli con mod Hostspot connection.autoconnect yes

Let me get this, it's possible to create hotspot without being connected to a WiFi?

yes, you can create without it

(I hope this is not annoying) Is it possible to run the hotspot on a rasbperry pi 5, and then connect to it? I can host the hotspot just fine, but when I try to connect it refuses because the hotspot has no internet. (It has no internet, not the network is not found.) Is there a way that you can connect to a network without internet using Raspbian lite?

@Vllben had the same problem on a raspberry pi 4 with Raspbian 12 (bookworm) and had to setup the nftables firewall accordingly for the client to be able to use the raspberry's internet connection:

sudo nft add table nat
sudo nft 'add chain nat postrouting { type nat hook postrouting priority 100 ; }'
sudo nft add rule nat postrouting masquerade

See https://wiki.nftables.org/wiki-nftables/index.php/Performing_Network_Address_Translation_(NAT)

In archlinux to share the wired internet via wifi, the dnsmasq packet is required for the network to lift properly.

It is also possible to create the network in a single command.

$ IFNAME="wlan0" && CON_NAME="MATARIFE" && PASSWD="password" && nmcli c add type wifi ifname $IFNAME con-name $CON_NAME autoconnect yes ssid $CON_NAME 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared wifi-sec.key-mgmt wpa-psk wifi-sec.psk "$PASSWD"

And then just lift the network.

$ nmcli con up $CON_NAME

We check that the wired network is sharing the internet via wifi.

$ nmcli d s | grep ^$IFNAME
wlan0          wifi      connected     MATARIFE

I also have a script that automates the procedure. For more information I also have a post on my Telegram channel dedicated to the topic.

I tried this method I reached till lift the network but when I run this command "nmcli con up $CON_NAME" I got an error saying -

Error: Connection activation failed: No suitable device found for this connection (device eno1 not available because profile is not compatible with device (mismatching interface name)).

Can you please help

Thanks! :-)

as an improvement for that command

IFNAME="wlan0" && CON_NAME="wifi name" && PASSWD="12345678" && nmcli c add type wifi ifname $IFNAME con-name "$CON_NAME" autoconnect yes ssid "$CON_NAME" 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared wifi-sec.key-mgmt wpa-psk wifi-sec.psk "$PASSWD"

if the wifi name has spaces it will work

same goes for the second command

nmcli con up "$CON_NAME"

I'm using a macbook.
When I try to connect to Hostspot, I keep getting prompted that WPA password is required.
Even though I used the correct password, the display does not disappear.

Correct me if I'm wrong, but I think adding the following uses WPA2:

nmcli con modify Hostspot wifi-sec.group ccmp
nmcli con modify Hostspot wifi-sec.pairwise ccmp

and for WPA3 maybe something like this:

nmcli con modify Hostspot wifi-sec.key-mgmt sae

(Note: intentional misspelling of hotspot as Hostspot to match OP)