uniform conf

my.ini

#######################################################################
# File name: my.ini
# Created By: The Uniform Server Development Team
# Edited Last By: Mike Gleaves (ric)
# V 1.0 24-7-2016
######################################################################## 

[mysql]
default-character-set=utf8

# SERVER SECTION The following options will be read by the MySQL Server.
[mysqld]
#Do not delete next line. Used for setting port when run as service
#{service_port}
bind-address=127.0.0.1
# server-id = 1  Comment Prevents error Cannot open table mysql/slave_master_info
server-id = 0
pid-file=mysql.pid
explicit_defaults_for_timestamp
#default-storage-engine=MYISAM


skip-external-locking
 
character-set-server=utf8

# federated
skip-federated


# Uncomment the following if you are using InnoDB tables
 # Maximum allowed size for a single HEAP (in memory) table. This option
# is a protection against the accidential creation of a very large HEAP
# table which could otherwise use up all memory resources.
max_heap_table_size = 640M

# Size of the buffer used for doing full table scans.
# Allocated per thread, if a full scan is needed.
read_buffer_size = 20M

# When reading rows in sorted order after a sort, the rows are read
# through this buffer to avoid disk seeks. You can improve ORDER BY
# performance a lot, if set this to a high value.
# Allocated per thread, when needed.
read_rnd_buffer_size = 160M

# Sort buffer is used to perform sorts for some ORDER BY and GROUP BY
# queries. If sorted data does not fit into the sort buffer, a disk
# based merge sort is used instead - See the "Sort_merge_passes"
# status variable. Allocated per thread if sort is needed.
sort_buffer_size = 80M

# This buffer is used for the optimization of full JOINs (JOINs without
# indexes). Such JOINs are very bad for performance in most cases
# anyway, but setting this variable to a large value reduces the
# performance impact. See the "Select_full_join" status variable for a
# count of full JOINs. Allocated per thread if full join is found
join_buffer_size = 80M

# Query cache is used to cache SELECT results and later return them
# without actual executing the same query once again. Having the query
# cache enabled may result in significant speed improvements, if your
# have a lot of identical queries and rarely changing tables. See the
# "Qcache_lowmem_prunes" status variable to check if the current value
# is high enough for your load.
# Note: In case your tables change very often or if your queries are
# textually different every time, the query cache may result in a
# slowdown instead of a performance improvement.
query_cache_size = 640M

# Only cache result sets that are smaller than this limit. This is to
# protect the query cache of a very large result set overwriting all
# other query results.
query_cache_limit = 20M

# Thread stack size to use. This amount of memory is always reserved at
# connection time. MySQL itself usually needs no more than 64K of
# memory, while if you use your own stack hungry UDF functions or your
# OS requires more stack for some operations, you might need to set this
# to a higher value.
thread_stack = 1920K

# Set the default transaction isolation level. Levels available are:
# READ-UNCOMMITTED, READ-COMMITTED, REPEATABLE-READ, SERIALIZABLE
transaction_isolation = READ-COMMITTED

# Maximum size for internal (in-memory) temporary tables. If a table
# grows larger than this value, it is automatically converted to disk
# based table This limitation is for a single table. There can be many
# of them.
tmp_table_size = 640M

# Additional memory pool that is used by InnoDB to store metadata
# information.  If InnoDB requires more memory for this purpose it will
# start to allocate it from the OS.  As this is fast enough on most
# recent operating systems, you normally do not need to change this
# value. SHOW INNODB STATUS will display the current amount used.
innodb_additional_mem_pool_size = 160M

# InnoDB, unlike MyISAM, uses a buffer pool to cache both indexes and
# row data. The bigger you set this the less disk I/O is needed to
# access data in tables. On a dedicated database server you may set this
# parameter up to 80% of the machine physical memory size. Do not set it
# too large, though, because competition of the physical memory may
# cause paging in the operating system.  Note that on 32bit systems you
# might be limited to 2-3.5G of user level memory per process, so do not
# set it too high.
innodb_buffer_pool_size = 2G

#innodb_buffer_pool_size=8G
#innodb_log_file_size=2G


[mysqldump]
quick
max_allowed_packet = 16M

[mysql]
no-auto-rehash
# Remove the next comment character if you are not familiar with SQL
#safe-updates

[myisamchk]
key_buffer_size = 8M
sort_buffer_size = 8M

[mysqlhotcopy]
interactive-timeout