Last active
July 4, 2017 00:16
-
-
Save nooitaf/6384363ce48be52b5f9bb3f96da28f73 to your computer and use it in GitHub Desktop.
QX95 - stock settings
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
# dump | |
# version | |
# Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) | |
# dump master | |
# mixer | |
mixer QUADX | |
mmix reset | |
smix reset | |
# feature | |
feature -RX_PPM | |
feature -VBAT | |
feature -INFLIGHT_ACC_CAL | |
feature -RX_SERIAL | |
feature -MOTOR_STOP | |
feature -SERVO_TILT | |
feature -SOFTSERIAL | |
feature -GPS | |
feature -FAILSAFE | |
feature -SONAR | |
feature -TELEMETRY | |
feature -CURRENT_METER | |
feature -3D | |
feature -RX_PARALLEL_PWM | |
feature -RX_MSP | |
feature -RSSI_ADC | |
feature -LED_STRIP | |
feature -DISPLAY | |
feature -ONESHOT125 | |
feature -BLACKBOX | |
feature -CHANNEL_FORWARDING | |
feature -TRANSPONDER | |
feature VBAT | |
feature RX_SERIAL | |
feature MOTOR_STOP | |
feature FAILSAFE | |
feature TELEMETRY | |
feature CURRENT_METER | |
feature RSSI_ADC | |
feature LED_STRIP | |
# map | |
map TAER1234 | |
# serial | |
serial 20 1 115200 57600 0 115200 | |
serial 0 1 115200 57600 0 115200 | |
serial 1 64 115200 57600 0 115200 | |
serial 2 0 115200 57600 0 115200 | |
# led | |
led 0 0,7::IC:3 | |
led 1 15,7::IATC:12 | |
led 2 7,7::IATC:12 | |
led 3 8,7::IC:3 | |
led 4 0,0:::0 | |
led 5 0,0:::0 | |
led 6 0,0:::0 | |
led 7 0,0:::0 | |
led 8 0,0:::0 | |
led 9 0,0:::0 | |
led 10 0,0:::0 | |
led 11 0,0:::0 | |
led 12 0,0:::0 | |
led 13 0,0:::0 | |
led 14 0,0:::0 | |
led 15 0,0:::0 | |
led 16 0,0:::0 | |
led 17 0,0:::0 | |
led 18 0,0:::0 | |
led 19 0,0:::0 | |
led 20 0,0:::0 | |
led 21 0,0:::0 | |
led 22 0,0:::0 | |
led 23 0,0:::0 | |
led 24 0,0:::0 | |
led 25 0,0:::0 | |
led 26 0,0:::0 | |
led 27 0,0:::0 | |
led 28 0,0:::0 | |
led 29 0,0:::0 | |
led 30 0,0:::0 | |
led 31 0,0:::0 | |
# color | |
color 0 0,0,0 | |
color 1 0,255,255 | |
color 2 0,0,255 | |
color 3 30,0,255 | |
color 4 60,0,255 | |
color 5 90,0,255 | |
color 6 120,0,255 | |
color 7 150,0,255 | |
color 8 180,0,255 | |
color 9 210,0,255 | |
color 10 240,0,255 | |
color 11 270,0,255 | |
color 12 300,0,255 | |
color 13 330,0,255 | |
color 14 0,0,0 | |
color 15 0,0,0 | |
# mode_color | |
mode_color 0 0 1 | |
mode_color 0 1 11 | |
mode_color 0 2 2 | |
mode_color 0 3 13 | |
mode_color 0 4 10 | |
mode_color 0 5 3 | |
mode_color 1 0 5 | |
mode_color 1 1 11 | |
mode_color 1 2 3 | |
mode_color 1 3 13 | |
mode_color 1 4 10 | |
mode_color 1 5 3 | |
mode_color 2 0 10 | |
mode_color 2 1 11 | |
mode_color 2 2 4 | |
mode_color 2 3 13 | |
mode_color 2 4 10 | |
mode_color 2 5 3 | |
mode_color 3 0 8 | |
mode_color 3 1 11 | |
mode_color 3 2 4 | |
mode_color 3 3 13 | |
mode_color 3 4 10 | |
mode_color 3 5 3 | |
mode_color 4 0 7 | |
mode_color 4 1 11 | |
mode_color 4 2 3 | |
mode_color 4 3 13 | |
mode_color 4 4 10 | |
mode_color 4 5 3 | |
mode_color 5 0 9 | |
mode_color 5 1 11 | |
mode_color 5 2 2 | |
mode_color 5 3 13 | |
mode_color 5 4 10 | |
mode_color 5 5 3 | |
mode_color 6 0 6 | |
mode_color 6 1 10 | |
mode_color 6 2 1 | |
mode_color 6 3 0 | |
mode_color 6 4 0 | |
mode_color 6 5 2 | |
mode_color 6 6 3 | |
mode_color 6 7 6 | |
set looptime = 1000 | |
set emf_avoidance = OFF | |
set i2c_highspeed = ON | |
set gyro_sync = ON | |
set gyro_sync_denom = 1 | |
set mid_rc = 1500 | |
set min_check = 1100 | |
set max_check = 1900 | |
set rssi_channel = 0 | |
set rssi_scale = 30 | |
set rssi_ppm_invert = OFF | |
set rc_smoothing = OFF | |
set rx_min_usec = 885 | |
set rx_max_usec = 2115 | |
set serialrx_provider = SBUS | |
set sbus_inversion = ON | |
set spektrum_sat_bind = 0 | |
set input_filtering_mode = OFF | |
set min_throttle = 1150 | |
set max_throttle = 2000 | |
set min_command = 1000 | |
set servo_center_pulse = 1500 | |
set motor_pwm_rate = 1000 | |
set servo_pwm_rate = 50 | |
set 3d_deadband_low = 1406 | |
set 3d_deadband_high = 1514 | |
set 3d_neutral = 1460 | |
set retarded_arm = OFF | |
set disarm_kill_switch = ON | |
set auto_disarm_delay = 5 | |
set max_arm_angle = 25 | |
set small_angle = 25 | |
set fixedwing_althold_dir = 1 | |
set reboot_character = 82 | |
set gps_provider = NMEA | |
set gps_sbas_mode = AUTO | |
set gps_auto_config = ON | |
set gps_auto_baud = OFF | |
set telemetry_switch = OFF | |
set telemetry_inversion = ON | |
set frsky_default_lattitude = 0.000 | |
set frsky_default_longitude = 0.000 | |
set frsky_coordinates_format = 0 | |
set frsky_unit = IMPERIAL | |
set frsky_vfas_precision = 0 | |
set hott_alarm_sound_interval = 5 | |
set battery_capacity = 0 | |
set vbat_scale = 110 | |
set vbat_max_cell_voltage = 43 | |
set vbat_min_cell_voltage = 33 | |
set vbat_warning_cell_voltage = 35 | |
set current_meter_scale = 400 | |
set current_meter_offset = 0 | |
set multiwii_current_meter_output = OFF | |
set current_meter_type = ADC | |
set align_gyro = DEFAULT | |
set align_acc = DEFAULT | |
set align_mag = DEFAULT | |
set align_board_roll = 0 | |
set align_board_pitch = 0 | |
set align_board_yaw = 0 | |
set max_angle_inclination = 500 | |
set gyro_lpf = 188HZ | |
set gyro_soft_lpf = 60 | |
set moron_threshold = 32 | |
set imu_dcm_kp = 2500 | |
set imu_dcm_ki = 0 | |
set pid_at_min_throttle = ON | |
set yaw_motor_direction = 1 | |
set yaw_jump_prevention_limit = 200 | |
set tri_unarmed_servo = ON | |
set servo_lowpass_freq = 400.000 | |
set servo_lowpass_enable = OFF | |
set failsafe_delay = 10 | |
set failsafe_off_delay = 200 | |
set failsafe_throttle = 1000 | |
set failsafe_kill_switch = OFF | |
set failsafe_throttle_low_delay = 100 | |
set failsafe_procedure = 0 | |
set acc_hardware = 0 | |
set baro_hardware = 0 | |
set mag_hardware = 0 | |
set blackbox_rate_num = 1 | |
set blackbox_rate_denom = 1 | |
set blackbox_device = SDCARD | |
set magzero_x = 0 | |
set magzero_y = 0 | |
set magzero_z = 0 | |
# rxfail | |
rxfail 0 a | |
rxfail 1 a | |
rxfail 2 a | |
rxfail 3 a | |
rxfail 4 h | |
rxfail 5 h | |
rxfail 6 h | |
rxfail 7 h | |
rxfail 8 h | |
rxfail 9 h | |
rxfail 10 h | |
rxfail 11 h | |
rxfail 12 h | |
rxfail 13 h | |
rxfail 14 h | |
rxfail 15 h | |
rxfail 16 h | |
rxfail 17 h | |
# dump profile | |
# profile | |
profile 0 | |
# aux | |
aux 0 0 0 1450 2100 | |
aux 1 1 0 1175 2100 | |
aux 2 0 0 900 900 | |
aux 3 0 0 900 900 | |
aux 4 0 0 900 900 | |
aux 5 0 0 900 900 | |
aux 6 0 0 900 900 | |
aux 7 0 0 900 900 | |
aux 8 0 0 900 900 | |
aux 9 0 0 900 900 | |
aux 10 0 0 900 900 | |
aux 11 0 0 900 900 | |
aux 12 0 0 900 900 | |
aux 13 0 0 900 900 | |
aux 14 0 0 900 900 | |
aux 15 0 0 900 900 | |
aux 16 0 0 900 900 | |
aux 17 0 0 900 900 | |
aux 18 0 0 900 900 | |
aux 19 0 0 900 900 | |
# adjrange | |
adjrange 0 0 0 900 900 0 0 | |
adjrange 1 0 0 900 900 0 0 | |
adjrange 2 0 0 900 900 0 0 | |
adjrange 3 0 0 900 900 0 0 | |
adjrange 4 0 0 900 900 0 0 | |
adjrange 5 0 0 900 900 0 0 | |
adjrange 6 0 0 900 900 0 0 | |
adjrange 7 0 0 900 900 0 0 | |
adjrange 8 0 0 900 900 0 0 | |
adjrange 9 0 0 900 900 0 0 | |
adjrange 10 0 0 900 900 0 0 | |
adjrange 11 0 0 900 900 0 0 | |
# rxrange | |
rxrange 0 1000 2000 | |
rxrange 1 1000 2000 | |
rxrange 2 1000 2000 | |
rxrange 3 1000 2000 | |
# servo | |
servo 0 1000 2000 1500 45 45 100 -1 | |
servo 1 1000 2000 1500 45 45 100 -1 | |
servo 2 1000 2000 1500 45 45 100 -1 | |
servo 3 1000 2000 1500 45 45 100 -1 | |
servo 4 1000 2000 1500 45 45 100 -1 | |
servo 5 1000 2000 1500 45 45 100 -1 | |
servo 6 1000 2000 1500 45 45 100 -1 | |
servo 7 1000 2000 1500 45 45 100 -1 | |
set gps_pos_p = 15 | |
set gps_pos_i = 0 | |
set gps_pos_d = 0 | |
set gps_posr_p = 34 | |
set gps_posr_i = 14 | |
set gps_posr_d = 53 | |
set gps_nav_p = 25 | |
set gps_nav_i = 33 | |
set gps_nav_d = 83 | |
set gps_wp_radius = 200 | |
set nav_controls_heading = ON | |
set nav_speed_min = 100 | |
set nav_speed_max = 300 | |
set nav_slew_rate = 30 | |
set alt_hold_deadband = 40 | |
set alt_hold_fast_change = ON | |
set deadband = 0 | |
set yaw_deadband = 0 | |
set yaw_control_direction = 1 | |
set 3d_deadband_throttle = 0 | |
set throttle_correction_value = 0 | |
set throttle_correction_angle = 800 | |
set default_rate_profile = 0 | |
set gimbal_mode = NORMAL | |
set acc_cut_hz = 15 | |
set accxy_deadband = 40 | |
set accz_deadband = 40 | |
set accz_lpf_cutoff = 5.000 | |
set acc_unarmedcal = ON | |
set acc_trim_pitch = 0 | |
set acc_trim_roll = 4 | |
set baro_tab_size = 21 | |
set baro_noise_lpf = 0.600 | |
set baro_cf_vel = 0.985 | |
set baro_cf_alt = 0.965 | |
set mag_declination = 0 | |
set pid_controller = MWREWRITE | |
set p_pitch = 80 | |
set i_pitch = 30 | |
set d_pitch = 44 | |
set p_roll = 80 | |
set i_roll = 30 | |
set d_roll = 44 | |
set p_yaw = 185 | |
set i_yaw = 45 | |
set d_yaw = 0 | |
set p_alt = 50 | |
set i_alt = 0 | |
set d_alt = 0 | |
set p_level = 15 | |
set i_level = 10 | |
set d_level = 100 | |
set p_vel = 120 | |
set i_vel = 45 | |
set d_vel = 1 | |
set yaw_p_limit = 500 | |
set dterm_cut_hz = 0 | |
set gtune_loP_rll = 10 | |
set gtune_loP_ptch = 10 | |
set gtune_loP_yw = 10 | |
set gtune_hiP_rll = 100 | |
set gtune_hiP_ptch = 100 | |
set gtune_hiP_yw = 100 | |
set gtune_pwr = 0 | |
set gtune_settle_time = 450 | |
set gtune_average_cycles = 16 | |
# dump rates | |
# rateprofile | |
rateprofile 0 | |
set rc_rate = 90 | |
set rc_expo = 65 | |
set rc_yaw_expo = 0 | |
set thr_mid = 50 | |
set thr_expo = 0 | |
set roll_rate = 80 | |
set pitch_rate = 80 | |
set yaw_rate = 50 | |
set tpa_rate = 0 | |
set tpa_breakpoint = 1500 | |
# |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment