DongshanPi Nezha STU stock firmware boot log (NAND flash)

dongshanpi-nezha-stu-stock-firmware-boot.log

[52]HELLO! BOOT0 is starting!
[55]BOOT0 commit : 9d92598
[58]set pll start
[60]periph0 has been enabled
[62]set pll end
[64][pmu]: bus read error
[66]board init ok
[68]DRAM only have internal ZQ!!
[71]get_pmu_exist() = -1
[73]DRAM BOOT DRIVE INFO: V0.32
[76]DRAM CLK = 936 MHz
[78]DRAM Type = 3 (2:DDR2,3:DDR3)
[81]DRAMC ZQ value: 0x7b7bfb
[84]DRAM ODT value: 0x42.
[87]ddr_efuse_type: 0x0
[89]mark_id: 0x50
[91]DRAM SIZE =512 M
[93]PLL_DDR_CTRL_REG:0xf9004d00
[96]DRAM_CLK_REG:0xc0000000
[99][TIMING DEBUG] MR2= 0x20
[103]DRAM simple test OK.
[105]dram size =512
[107]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[112]block from 8 to 32
[183]Check is correct.
[185]dma 0x300e8 int is not used yet
[189]dma 0x300e8 int is free, you do not need to free it again
[194]Entry_name        = opensbi
[197]Entry_name        = u-boot
[201]Entry_name        = dtb
[203]Jump to second Boot.

OpenSBI v0.6
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x40000400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000040000000-0x000000004001ffff (A)
PMP1    : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2    : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3    : 0x0000000000020000-0x0000000000027fff (A,�

U-Boot 2018.05-00028-g01087f40d6-config-dirty (Aug 20 2021 - 17:08:37 +0800) Allwinner Technology

[00.288]DRAM:  512 MiB
[00.290]Relocation Offset is: 1dee2000
[00.294]secure enable bit: 0
[00.297]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.303]flash init start
[00.305]workmode = 0,storage type = 0
[00.312]sunxi-spinand-phy: not detect any munufacture from id table
[00.318]sunxi-spinand-phy: get spi-nand Model from fdt fail
[00.323]sunxi-spinand-phy: get phy info from fdt fail

device nand0 <nand>, # parts = 4
 #: name		size		offset		mask_flags
 0: boot0               0x00100000	0x00000000	1
 1: uboot               0x00300000	0x00100000	1
 2: secure_storage      0x00100000	0x00400000	1
 3: sys                 0x07b00000	0x00500000	0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.477]ubi0: attaching mtd4
[00.653]ubi0: scanning is finished
[00.662]ubi0: attached mtd4 (name "sys", size 123 MiB)
[00.666]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.673]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.679]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.685]ubi0: good PEBs: 491, bad PEBs: 1, corrupted PEBs: 0
[00.690]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[00.697]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[00.705]ubi0: available PEBs: 0, total reserved PEBs: 491, PEBs reserved for bad PEB handling: 19
[00.713]sunxi flash init ok
[00.716]line:714 init_clocks
__clk_init: clk pll_periph0x2 already initialized
register fix_factor clk error
[00.726]drv_disp_init
request pwm success, pwm2:pwm2:0x2000c00.
[00.743]drv_disp_init finish
[00.745]boot_gui_init:start
[00.748]set disp.dev2_output_type fail. using defval=0
[00.775]boot_gui_init:finish
[01.007]LCD open finish
partno erro : can't find partition bootloader
54 bytes read in 0 ms
[01.148]bmp_name=bootlogo.bmp size 3072054
3072054 bytes read in 114 ms (25.7 MiB/s)
[01.467]Loading Environment from SUNXI_FLASH... OK
[01.499]out of usb burn from boot: not need burn key
[01.522]update bootcmd
[01.542]change working_fdt 0x5eaa1da0 to 0x5ea81da0
No reserved memory region found in source FDT
[01.569]update dts
noncached_alloc(): addr = 0x5eac3c40
noncached_alloc(): addr = 0x5ef10940
noncached_alloc(): addr = 0x5ef10980
noncached_alloc(): addr = 0x5ef111c0
phy_mode=rgmii, phy_interface=7
gmac: *** using ephy_clk ***
eth0
Warning: eth0 (eth0) using random MAC address - d6:94:f5:18:ee:05

Hit any key to stop autoboot:  0 
dsp0:gpio init config fail
dsp0:sharespace config fail
dsp0 version is r528-tina-v1.0.0-release-17-g7e872ce-dirty
DSP0 start ok, img length 256148, booting from 0x400660
[02.114]no vendor_boot partition is found
Android's image name: d1-nezha
Detect comp gzip
[02.363]
Starting kernel ...

[    0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000
[    0.000000] Linux version 5.4.61 (kunyao@AwExdroid89) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #14 PREEMPT Fri Aug 20 09:15:45 UTC 2021
[    0.000000] cma: Reserved 8 MiB at 0x000000005f800000
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000040200000-0x000000005fffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040200000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000005fffffff]
[    0.000000] On node 0 totalpages: 130560
[    0.000000]   DMA32 zone: 1785 pages used for memmap
[    0.000000]   DMA32 zone: 0 pages reserved
[    0.000000]   DMA32 zone: 130560 pages, LIFO batch:31
[    0.000000] elf_hwcap is 0x20112d
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 128775
[    0.000000] Kernel command line: ubi.mtd=sys ubi.block=0,rootfs earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/ubiblock0_5 rootfstype=squashfs init=/sbin/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:recovery@ubi0_7:UDISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun20iw1p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.05-00028-g01087f40d6-config-d
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Sorting __ex_table...
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 491120K/522240K available (6377K kernel code, 666K rwdata, 2157K rodata, 212K init, 254K bss, 22928K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[    0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000021] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[    0.000313] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000911] Console: colour dummy device 80x25
[    0.000946] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000961] pid_max: default: 32768 minimum: 301
[    0.001135] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.001153] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.002643] ASID allocator initialised with 65536 entries
[    0.002789] rcu: Hierarchical SRCU implementation.
[    0.003375] devtmpfs: initialized
[    0.015613] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0
[    0.016533] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.016559] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[    0.016911] pinctrl core: initialized pinctrl subsystem
[    0.018095] NET: Registered protocol family 16
[    0.019916] DMA: preallocated 256 KiB pool for atomic allocations
[    0.020529] cpuidle: using governor menu
[    0.061936] rtc_ccu: sunxi ccu init OK
[    0.070904] clock: sunxi ccu init OK
[    0.071664] clock: sunxi ccu init OK
[    0.101530] iommu: Default domain type: Translated 
[    0.101683] sunxi iommu: irq = 4
[    0.102706] SCSI subsystem initialized
[    0.103004] usbcore: registered new interface driver usbfs
[    0.103074] usbcore: registered new interface driver hub
[    0.103168] usbcore: registered new device driver usb
[    0.103325] mc: Linux media interface: v0.10
[    0.103375] videodev: Linux video capture interface: v2.00
[    0.104341] sunxi-msgbox-amp 3003000.msgbox: invalid resource
[    0.105068] Advanced Linux Sound Architecture Driver Initialized.
[    0.105578] Bluetooth: Core ver 2.22
[    0.105644] NET: Registered protocol family 31
[    0.105653] Bluetooth: HCI device and connection manager initialized
[    0.105672] Bluetooth: HCI socket layer initialized
[    0.105685] Bluetooth: L2CAP socket layer initialized
[    0.105717] Bluetooth: SCO socket layer initialized
[    0.105972] pwm module init!
[    0.107370] g2d 5410000.g2d: Adding to iommu group 0
[    0.107812] G2D: rcq version initialized.major:250
[    0.108430] input: sunxi-keyboard as /devices/virtual/input/input0
[    0.109880] clocksource: Switched to clocksource riscv_clocksource
[    0.120525] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.134415] thermal_sys: Registered thermal governor 'user_space'
[    0.134420] thermal_sys: Registered thermal governor 'power_allocator'
[    0.134868] NET: Registered protocol family 2
[    0.135606] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.135643] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.135701] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.135746] TCP: Hash tables configured (established 4096 bind 4096)
[    0.135869] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.135904] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.136104] NET: Registered protocol family 1
[    0.137212] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    0.137703] spi spi0: spi0 supply spi not found, using dummy regulator
[    0.137913] sunxi_spi_resource_get()2088 - [spi0] SPI MASTER MODE
[    0.138013] sunxi_spi_clk_init()2164 - [spi0] mclk 100000000
[    0.138607] sunxi_spi_probe()2570 - [spi0]: driver probe succeed, base ffffffd004060000, irq 31
[    0.140520] Initialise system trusted keyrings
[    0.140730] workingset: timestamp_bits=62 max_order=17 bucket_order=0
[    0.146979] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.167423] Key type asymmetric registered
[    0.167436] Asymmetric key parser 'x509' registered
[    0.167456] io scheduler mq-deadline registered
[    0.167463] io scheduler kyber registered
[    0.167480] atomic64_test: passed
[    0.168594] [DISP]disp_module_init
[    0.169099] disp 5000000.disp: Adding to iommu group 0
[    0.169668] [DISP] disp_init,line:2385:
[    0.169673] smooth display screen:0 type:1 mode:4
[    0.204484] display_fb_request,fb_id:0
[    0.238906] disp_al_manager_apply ouput_type:1
[    0.239052] [DISP] lcd_clk_config,line:731:
[    0.239064] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000)
[    0.239064]      clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000)
[    0.239435] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[    0.240122] [DISP]disp_module_init finish
[    0.241002] sunxi_sid_init()551 - insmod ok
[    0.241508] pwm-regulator: supplied by regulator-dummy
[    0.247987] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    0.248394] uart uart0: get regulator failed
[    0.248420] uart uart0: uart0 supply uart not found, using dummy regulator
[    0.248703] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI
[    0.248726] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
[    1.055260] printk: console [ttyS0] enabled
[    1.060758] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    1.072173] uart uart1: get regulator failed
[    1.076948] uart uart1: uart1 supply uart not found, using dummy regulator
[    1.084966] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI
[    1.094785] misc dump reg init
[    1.099007] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    1.106298] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    1.113620] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    1.121065] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    1.127572] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    1.134556] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[    1.142288] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[    1.150141] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[    1.158248] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[    1.165861] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[    1.172658] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[    1.180193] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0
[    1.188306] [ADDR_MGT] addr_mgt_probe: module version: v1.0.9
[    1.195808] [ADDR_MGT] addr_mgt_probe: success.
[    1.201799] sunxi-spinand: AW SPINand MTD Layer Version: 2.0 20201228
[    1.208998] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[    1.216924] sunxi-spinand-phy: not detect any munufacture from id table
[    1.224361] sunxi-spinand-phy: get spi-nand Model from fdt fail
[    1.230988] sunxi-spinand-phy: get phy info from fdt fail
[    1.237023] sunxi-spinand-phy: not detect munufacture from fdt
[    1.243719] sunxi-spinand-phy: detect munufacture from id table: Mxic
[    1.250964] sunxi-spinand-phy: detect spinand id: ffff12c2 ffffffff
[    1.257948] sunxi-spinand-phy: ========== arch info ==========
[    1.264502] sunxi-spinand-phy: Model:               MX35LF1GE4AB
[    1.271226] sunxi-spinand-phy: Munufacture:         Mxic
[    1.277146] sunxi-spinand-phy: DieCntPerChip:       1
[    1.282821] sunxi-spinand-phy: BlkCntPerDie:        1024
[    1.288739] sunxi-spinand-phy: PageCntPerBlk:       64
[    1.294484] sunxi-spinand-phy: SectCntPerPage:      4
[    1.300162] sunxi-spinand-phy: OobSizePerPage:      64
[    1.305887] sunxi-spinand-phy: BadBlockFlag:        0x1
[    1.311730] sunxi-spinand-phy: OperationOpt:        0x7
[    1.317568] sunxi-spinand-phy: MaxEraseTimes:       65000
[    1.323604] sunxi-spinand-phy: EccFlag:             0x2
[    1.329424] sunxi-spinand-phy: EccType:             4
[    1.335096] sunxi-spinand-phy: EccProtectedType:    3
[    1.340747] sunxi-spinand-phy: ========================================
[    1.348133] sunxi-spinand-phy: 
[    1.351652] sunxi-spinand-phy: ========== physical info ==========
[    1.358539] sunxi-spinand-phy: TotalSize:    128 M
[    1.363924] sunxi-spinand-phy: SectorSize:   512 B
[    1.369261] sunxi-spinand-phy: PageSize:     2 K
[    1.374427] sunxi-spinand-phy: BlockSize:    128 K
[    1.379779] sunxi-spinand-phy: OOBSize:      64 B
[    1.385041] sunxi-spinand-phy: ========================================
[    1.392431] sunxi-spinand-phy: 
[    1.395942] sunxi-spinand-phy: ========== logical info ==========
[    1.402756] sunxi-spinand-phy: TotalSize:    128 M
[    1.408093] sunxi-spinand-phy: SectorSize:   512 B
[    1.413475] sunxi-spinand-phy: PageSize:     4 K
[    1.418619] sunxi-spinand-phy: BlockSize:    256 K
[    1.423977] sunxi-spinand-phy: OOBSize:      128 B
[    1.429328] sunxi-spinand-phy: ========================================
[    1.436839] sunxi-spinand-phy: block lock register: 0x00
[    1.442953] sunxi-spinand-phy: feature register: 0x11
[    1.448606] sunxi-spinand-phy: sunxi physic nand init end
[    1.455203] Creating 4 MTD partitions on "sunxi_mtd_nand":
[    1.461443] 0x000000000000-0x000000100000 : "boot0"
[    1.480918] 0x000000100000-0x000000500000 : "uboot"
[    1.487954] random: fast init done
[    1.510899] 0x000000500000-0x000000600000 : "secure_storage"
[    1.530893] 0x000000600000-0x000008000000 : "sys"
[    1.912766] sunxi-spinand-phy: phy blk 919 is bad
[    1.929841] random: crng init done
[    1.981334] libphy: Fixed MDIO Bus: probed
[    1.985902] CAN device driver interface
[    1.991680] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    2.003007] sunxi gmac driver's version: 1.0.0
[    2.008099] gmac-power0: NULL
[    2.011448] gmac-power1: NULL
[    2.014779] gmac-power2: NULL
[    2.019096] Failed to alloc md5
[    2.022680] eth0: Use random mac address
[    2.027373] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.034771] sunxi-ehci: EHCI SUNXI driver
[    2.039740] get ehci1-controller wakeup-source is fail.
[    2.045776] sunxi ehci1-controller don't init wakeup source
[    2.052064] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe00095ef28, 0x:ffffffd0040c1000, irq_no:31
[    2.065650] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
[    2.078205] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    2.090411] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    2.097657] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    2.107468] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[    2.139925] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    2.148555] hub 1-0:1.0: USB hub found
[    2.152845] hub 1-0:1.0: 1 port detected
[    2.157943] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.164963] sunxi-ohci: OHCI SUNXI driver
[    2.170007] get ohci1-controller wakeup-source is fail.
[    2.175959] sunxi ohci1-controller don't init wakeup source
[    2.182209] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe00095fa80
[    2.192680] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
[    2.205183] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    2.217411] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    2.224706] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    2.234470] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[    2.314766] hub 2-0:1.0: USB hub found
[    2.318991] hub 2-0:1.0: 1 port detected
[    2.324402] usbcore: registered new interface driver uas
[    2.330552] usbcore: registered new interface driver usb-storage
[    2.337303] usbcore: registered new interface driver ums-alauda
[    2.344078] usbcore: registered new interface driver ums-cypress
[    2.350879] usbcore: registered new interface driver ums-datafab
[    2.357662] usbcore: registered new interface driver ums_eneub6250
[    2.364663] usbcore: registered new interface driver ums-freecom
[    2.371512] usbcore: registered new interface driver ums-isd200
[    2.378171] usbcore: registered new interface driver ums-jumpshot
[    2.385069] usbcore: registered new interface driver ums-karma
[    2.391711] usbcore: registered new interface driver ums-onetouch
[    2.398576] usbcore: registered new interface driver ums-realtek
[    2.405419] usbcore: registered new interface driver ums-sddr09
[    2.412121] usbcore: registered new interface driver ums-sddr55
[    2.418847] usbcore: registered new interface driver ums-usbat
[    2.425860] sunxi_gpadc_init,2145, success
[    2.432506] sunxi-rtc 7090000.rtc: registered as rtc0
[    2.438277] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:31 UTC (31)
[    2.447289] sunxi-rtc 7090000.rtc: sunxi rtc probed
[    2.453239] i2c /dev entries driver
[    2.457217] IR NEC protocol handler initialized
[    2.462960] sunxi cedar version 1.1
[    2.467096] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    2.473418] VE: install start!!!
[    2.473418] 
[    2.478879] VE: cedar-ve the get irq is 6
[    2.478879] 
[    2.485277] VE: ve_debug_proc_info:00000000f351aaae, data:000000007733abc8, lock:000000008a9d7978
[    2.485277] 
[    2.496856] VE: install end!!!
[    2.496856] 
[    2.503474] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    2.512598] Bluetooth: HCI UART driver ver 2.3
[    2.517580] Bluetooth: HCI UART protocol H4 registered
[    2.523344] Bluetooth: HCI UART protocol BCSP registered
[    2.529266] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    2.536554] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1
[    2.542964] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1
[    2.549519] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled!
[    2.549519] 
[    2.558189] [XR_BT_LPM] bluesleep_probe: uart_index(1)
[    2.567593] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.23 2021-06-16 10:10)
[    2.577544] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    2.583786] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    2.590126] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    2.596533] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    2.602989] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    2.609493] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    2.616046] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    2.622575] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    2.629476] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[    2.634985] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[    2.641625] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.652795] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    2.672946] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.684604] sunxi-mmc 4020000.sdmmc: failed to get DS26_SDR12 used default
[    2.705034] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[    2.710758] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.723003] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.23 2021-06-16 10:10)
[    2.732847] sunxi-mmc 4020000.sdmmc: failed to get DS26_SDR12 used default
[    2.740764] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    2.746958] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    2.753350] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    2.759789] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    2.766284] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    2.772822] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.784423] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    2.790958] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    2.797478] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    2.804065] sunxi-mmc 4020000.sdmmc: failed to get DS26_SDR12 used default
[    2.811854] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    2.821359] sunxi-mmc 4020000.sdmmc: smc 0 p0 err, cmd 8, RTO !!
[    2.828182] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.839250] sunxi-mmc 4020000.sdmmc: smc 0 p0 err, cmd 55, RTO !!
[    2.846191] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    2.853777] sunxi-mmc 4020000.sdmmc: smc 0 p0 err, cmd 55, RTO !!
[    2.861486] sunxi-mmc 4020000.sdmmc: smc 0 p0 err, cmd 55, RTO !!
[    2.869128] sunxi-mmc 4020000.sdmmc: smc 0 p0 err, cmd 55, RTO !!
[    2.875985] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.887082] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.898809] sunxi-mmc 4021000.sdmmc: failed to get DS26_SDR12 used default
[    2.919151] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    2.926835] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.933806] sunxi_led_probe()1715 - start
[    2.938293] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.945176] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.956810] sunxi_get_str_of_property()1560 - failed to get the string of propname led_regulator!
[    2.966799] sunxi-mmc 4021000.sdmmc: failed to get DS26_SDR12 used default
[    2.974593] sunxi_register_led_classdev()1448 - led_classdev start
[    2.983213] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.997173] sunxi_led_probe()1820 - finish
[    3.002358] usbcore: registered new interface driver usbhid
[    3.008595] usbhid: USB HID core driver
[    3.012978] sunxi-mmc 4021000.sdmmc: failed to get DS26_SDR12 used default
[    3.022462] usbcore: registered new interface driver snd-usb-audio
[    3.029373] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    3.036958] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    3.044540] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    3.052127] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    3.058881] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.071147] sunxi-daudio 2034000.daudio: regulator missing or invalid
[    3.079285] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    3.079285] 
[    3.096529] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    3.107896] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished
[    3.117275] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    3.127116] [SNDCODEC][sunxi_card_init][583]:card init finished
[    3.135743] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    3.146864] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1
[    3.158906] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished
[    3.167118] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: register device finished!
[    3.175622] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: [rpaf_dsp0] probe finished!
[    3.184684] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102!
[    3.196219] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed
[    3.208084] NET: Registered protocol family 10
[    3.214385] Segment Routing with IPv6
[    3.218665] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.226059] NET: Registered protocol family 17
[    3.231142] can: controller area network core (rev 20170425 abi 9)
[    3.238136] NET: Registered protocol family 29
[    3.243155] can: raw protocol (rev 20170425)
[    3.247938] can: broadcast manager protocol (rev 20170425 t)
[    3.254286] can: netlink gateway (rev 20190810) max_hops=1
[    3.260698] Bluetooth: RFCOMM TTY layer initialized
[    3.266177] Bluetooth: RFCOMM socket layer initialized
[    3.272023] Bluetooth: RFCOMM ver 1.11
[    3.277198] Loading compiled-in X.509 certificates
[    3.284726] HDMI 2.0 driver init start!
[    3.289014] boot_hdmi=false
[    3.292242] ERROR: pinctrl_get for HDMI2.0 DDC fail
[    3.299206] HDMI2.0 module init end
[    3.323423] i2c 2502800.twi: 2502800.twi supply twi not found, using dummy regulator
[    3.332357] i2c 2502800.twi: reg_clk = 0x14, clk_m = 5, clk_n = 0,mask_clk_m = 78, mask_clk_n = 7
[    3.342316] i2c 2502800.twi: reg: 0x14 value: 0xa8
[    3.347680] i2c 2502800.twi: set twi engine clock
[    3.359389] i2c i2c2: current xfer msg num = 1
[    3.364440] i2c i2c2: num: 0, data is follow: 
[    3.369394] i2c i2c2: 00 
[    3.372339] i2c i2c2: num: 1 data is display end
[    3.377488] i2c i2c2: twi engine xfer
[    3.381753] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[    3.391549] Oops [#1]
[    3.394073] Modules linked in:
[    3.397476] CPU: 0 PID: 13 Comm: kworker/0:1 Not tainted 5.4.61 #14
[    3.404470] Workqueue: events deferred_probe_work_func
[    3.410199] sepc: ffffffe00005b72e ra : ffffffe00005b67c sp : ffffffe01e36f4a0
[    3.418248]  gp : ffffffe000931e78 tp : ffffffe01e358ac0 t0 : ffffffe0009423b0
[    3.426296]  t1 : 0000000000000200 t2 : ffffffe0002a33b6 s0 : ffffffe01e36f4d0
[    3.434342]  s1 : ffffffe01e36f4e8 a0 : 0000000000000001 a1 : ffffffe01e36f4e8
[    3.442390]  a2 : 0000000000000002 a3 : 0000000000000004 a4 : 0000000000000000
[    3.450436]  a5 : ffffffe01e36f500 a6 : 000000000377b4f1 a7 : 0000000000000000
[    3.458484]  s2 : 0000000200000022 s3 : 0000000000000002 s4 : ffffffe01d411550
[    3.466532]  s5 : 0000000000000001 s6 : ffffffe00079f178 s7 : 0000000000000001
[    3.474580]  s8 : ffffffe01d411040 s9 : ffffffe0007f1bc0 s10: 0000000000000002
[    3.482628]  s11: 00000000000000f8 t3 : 0000000000000001 t4 : 0000000000000548
[    3.490677]  t5 : 0000000000000100 t6 : ffffffe00093c080
[    3.496594] sstatus: 0000000200000100 sbadaddr: 0000000000000008 scause: 000000000000000f
[    3.505763] ---[ end trace cc245d4caeff0a07 ]---
[    3.510961] note: kworker/0:1[13] exited with preempt_count 1
[    6.929912] hdmi_hpd_sys_config_release