Rafi's i3status configuration file

i3status.conf

# github.com/rafi i3status config

# i3status configuration file
# see "man i3status" for documentation.

# It is important that this file is edited as UTF-8.
# The following line should contain a sharp s:
# ß
# If the above line is not correctly displayed, fix your editor first!

general {
	colors = true
	color_good = "#BBBBBB"
	color_bad = "#CC1616"
	color_degraded = "#55858E"
	interval = 2
}

order += "volume master"
order += "load"
order += "cpu_usage"
order += "cpu_temperature 0"
order += "cpu_temperature 1"
order += "cpu_temperature 2"
order += "cpu_temperature 3"
order += "disk /"
order += "disk /media/media"
order += "ethernet eth0"
order += "tztime local"
#order += "ipv6"
#order += "run_watch DHCP"
#order += "run_watch VPN"
#order += "wireless wlan0"

volume master {
#	format = " ♪: %volume  " 
	device = "default"
	mixer = "Master"
	mixer_idx = 0
	# termsyn font
	format = "À %volume "
}

load {
#	format = " Δ: %1min "
	# termsyn font
	format = " Î %1min"
}

cpu_usage {
	format = "%usage "
}

cpu_temperature 0 {
	format = " ± %degrees°"
	path = "/sys/devices/platform/coretemp.0/temp2_input"
	max_threshold = 95
}

cpu_temperature 1 {
	format = "%degrees°"
	path = "/sys/devices/platform/coretemp.0/temp3_input"
	max_threshold = 95
}

cpu_temperature 2 {
	format = "%degrees°"
	path = "/sys/devices/platform/coretemp.0/temp4_input"
	max_threshold = 95
}

cpu_temperature 3 {
	format = "%degrees° "
	path = "/sys/devices/platform/coretemp.0/temp5_input"
	max_threshold = 95
}

disk "/" {
	format = " ¨ %avail:/ " 
}

disk "/media/media" {
	format = " ¨ %avail:m "
}

wireless wlan0 {
	format_up = " W: (%quality at %essid) %ip "
	format_down = " ☡ WiFi "
}

ethernet eth0 {
	# if you use %speed, i3status requires root privileges
#	format_up =  " Ω: %ip  "
#	format_down = " ∅ eth0  "

	# termsyn font
	format_up =  " ­ %ip "
	format_down = " Ð eth0 "
}

run_watch DHCP {
	pidfile = "/var/run/dhclient*.pid"
}

run_watch VPN {
	pidfile = "/var/run/vpnc/pid"
}

tztime local {
#	format = " %h-%d %H:%M ☰ "
	# termsyn font
	format = " %h-%d É %H:%M  ¸ ÈÈÈ È "
}

Hi. To me the format displayed doesn't make much sense. For example, in my editor I see À in volume and ÈÈÈ È after time. And I see the same on the i3status. Is this how its supposed to be?
I pasted the output of i3status below.
À 66% | Î 0,88 | -4% | ± 54° | 58° | ¨ 307,0 GiB:/ | | Ð eth0 | mars-09 É 18:34 ¸ ÈÈÈ È | DHCP: yes | VPN: no | ☡ WiFi

did you find a solution?

No. I am using plain text now. Check it our here https://github.com/saki92/i3status/blob/main/config