Printer settings dump

m503_m122.txt

Send: M503
Recv: echo:  G21    ; Units in mm (mm)
Recv: 
Recv: echo:Filament settings: Disabled
Recv: echo:  M200 D1.75
Recv: echo:  M200 D0
Recv: echo:Steps per unit:
Recv: echo: M92 X93.00 Y93.00 Z137.00 E104.00
Recv: echo:Maximum feedrates (units/s):
Recv: echo:  M203 X300.00 Y300.00 Z5.00 E25.00
Recv: echo:Maximum Acceleration (units/s2):
Recv: echo:  M201 X400.00 Y400.00 Z20.00 E10000.00
Recv: echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
Recv: echo:  M204 P400.00 R400.00 T400.00
Recv: echo:Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> J<junc_dev>
Recv: echo:  M205 B20000.00 S0.00 T0.00 J0.01
Recv: echo:Home offset:
Recv: echo:  M206 X0.00 Y0.00 Z0.00
Recv: echo:PID settings:
Recv: echo:  M301 P18.60 I0.98 D88.46
Recv: echo:  M304 P14.00 I0.90 D120.40
Recv: echo:Stepper driver current:
Recv: echo:  M906 X650 Y650 Z550
Recv: echo:  M906 T0 E550
Recv: 
Recv: echo:Driver stepping mode:
Recv: echo:  M569 S1 T0 E
Recv: echo:Filament load/unload lengths:
Recv: echo:  M603 L0.00 U100.00
Recv: ok


Send: M122
Recv: 		X	Y	Z	E
Recv: Address		0	0	0	0
Recv: Enabled		false	false	false	false
Recv: Set current	650	650	550	550
Recv: RMS current	642	642	520	520
Recv: MAX current	905	905	733	733
Recv: Run current	20/31	20/31	16/31	16/31
Recv: Hold current	10/31	10/31	8/31	8/31
Recv: CS actual	10/31	10/31	8/31	8/31
Recv: PWM scale	12	12	10	18
Recv: vsense		1=.18	1=.18	1=.18	1=.18
Recv: stealthChop	false	false	false	true
Recv: msteps		16	16	2	16
Recv: tstep		max	max	max	max
Recv: pwm
Recv: threshold
Recv: [mm/s]
Recv: OT prewarn	false	false	false	false
Recv: OT prewarn has
Recv: been triggered	false	false	false	false
Recv: off time	3	3	3	3
Recv: blank time	24	24	24	24
Recv: hysteresis
Recv: -end		-1	-1	-1	-1
Recv: -start		1	1	1	1
Recv: Stallguard thrs	0	0	0	0
Recv: DRVSTATUS	X	Y	Z	E
Recv: stst		*	*	*	*
Recv: olb
Recv: ola
Recv: s2gb
Recv: s2ga
Recv: otpw
Recv: ot
Recv: 157C
Recv: 150C
Recv: 143C
Recv: 120C
Recv: s2vsa
Recv: s2vsb
Recv: Driver registers:
Recv: 		X	0x80:0A:00:00
Recv: 		Y	0x80:0A:00:00
Recv: 		Z	0x80:08:00:00
Recv: 		E	0xC0:08:00:00
Recv: 
Recv: 
Recv: Testing X connection... OK
Recv: Testing Y connection... OK
Recv: Testing Z connection... OK
Recv: Testing E connection... OK
Recv: ok