shbatm

{
    "apps":[
        {
            "name":"mm",
            "script":"./mm.sh",
            "cwd":"/home/pi",
            "watch":[
                "/home/pi/MagicMirror/config/config.js"
            ],
            "watch_options":{

shbatm

/* Magic Mirror Config Sample
 *
 * By Michael Teeuw http://michaelteeuw.nl
 * MIT Licensed.
 *
 * For more information how you can configurate this file
 * See https://github.com/MichMich/MagicMirror#configuration
 *
 */

shbatm

        {
            module: "MMM-RTSPStream",
            position: "middle_center",
            header: "Camera Streams",
            config: {
                autoStart: false,
                rotateStreams: false,
                moduleWidth: 1120,
                moduleHeight: 784,
                stream1: {

shbatm

NodeLink AutoStart on Raspberry Pi (Raspbian Stretch)

The scripts included in this Gist are designed to start io_guy's NodeLink.exe as a startup service on a Raspberry Pi running Rasbian Stretch.

Installation

1. Follow the installation instructions for setting up NodeLink here.
2. STOP when you get to "Setting up rc.local"
3. Copy the contents of the file below to a file called installService.sh in the same folder as NodeLink.exe on your RPi:
4. Install the systemd service by running:

shbatm

How to use non-default Ports for diyHue Project using NGINX

This GIST contains the files required to be modified in order to run diyHue on non-default HTTP and HTTPS ports.

This example uses ports 8080 for HTTP and 8443 for HTTPS and redirects the necessary paths from NGINX's default site.

Changes made to diyHue Files

The following lines must be changed in the diyHue source code, as there is no option provided to change the ports by default.

shbatm

pi@bookcase2:~ $ cd MagicMirror/modules/
pi@bookcase2:~/MagicMirror/modules $ git clone [email protected]:shbatm/MMM-AlexaOnOff.git
Cloning into 'MMM-AlexaOnOff'...
remote: Enumerating objects: 32, done.
remote: Counting objects: 100% (32/32), done.
remote: Compressing objects: 100% (29/29), done.
remote: Total 32 (delta 12), reused 14 (delta 2), pack-reused 0
Receiving objects: 100% (32/32), 10.82 KiB | 0 bytes/s, done.
Resolving deltas: 100% (12/12), done.

shbatm

server {
    listen       80;
    server_name  localhost;

  location /oauth2/ {
    proxy_pass       http://oauth-proxy:4180;
    proxy_set_header Host                    $host;
    proxy_set_header X-Real-IP               $remote_addr;
    proxy_set_header X-Scheme                $scheme;
    proxy_set_header X-Auth-Request-Redirect $request_uri;

shbatm

Build & Install pusher/oauth2_proxy on Raspberry Pi

1. Install Latest golang

git clone https://github.com/udhos/update-golang
cd update-golang
sudo ./update-golang.sh

shbatm

ISY Climate Device Mode Definitions

Source : Pg 35 ISY SDK Documentation

66 = Thermostat heat/cool state

0 - Idle
1 - Heating
2 - Cooling

3 - Fan Only

shbatm

Files Included:

1. usbipd.service (server/physical device)
2. usbip.service (client/HASS host)
3. udev rules file for client host -- maps USB device to /dev/zwave (add to /etc/udev/rules.d/)
4. Client Manager Script

Setup:

See the original instructions here: https://community.home-assistant.io/t/rpi-as-z-wave-zigbee-over-ip-server-for-hass/23006 also see the notes below in each file.