Created
August 10, 2020 12:58
-
-
Save shibajee/1b44ef695d5951cbe5eed3779b429712 to your computer and use it in GitHub Desktop.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
U-Boot 1.1.3 (Aug 10 2020 - 04:02:58) | |
Board: MediaTek APSoC DRAM: 32 MB | |
enable ephy clock...done. SSC disabled. | |
MediaTek SPI flash driver, SPI clock: 50MHz | |
spi device id: c2 20 16 c2 20 (2016c220) | |
find flash: MX25L3205D | |
*** Warning - bad CRC, using default environment | |
============================================ | |
MediaTek U-Boot Version: 5.0.1.0-6 | |
-------------------------------------------- | |
ASIC 7620_MP (Port5<->None) | |
DRAM component: 256 Mbits DDR, width 16 | |
DRAM bus: 16 bit | |
Total memory: 32 MBytes | |
Flash component: SPI Flash | |
Date:Aug 10 2020 Time:04:02:58 | |
============================================ | |
icache: sets:512, ways:4, linesz:32, total:65536 | |
dcache: sets:256, ways:4, linesz:32, total:32768 | |
#### The CPU freq = 600 MHZ #### | |
estimate memory size = 32 Mbytes | |
Please choose the operation: | |
0: Load system code then write to Flash via Serial. | |
1: Load system code to SDRAM via TFTP. | |
2: Load system code then write to Flash via TFTP. | |
3: Boot system code via Flash (default). | |
4: Enter boot command line interface. | |
7: Load U-Boot code then write to Flash via Serial. | |
9: Load U-Boot code then write to Flash via TFTP. 0 | |
3: System Boot system code via Flash. | |
## Checking image at bc050000 ... | |
Image Name: JWNR2010V5 | |
Image Type: MIPS Linux Kernel Image (lzma compressed) | |
Data Size: 3452815 Bytes = 3.3 MB | |
Load Address: 80000000 | |
Entry Point: 80243330 | |
Verifying Checksum ... OK | |
Uncompressing Kernel Image ... OK | |
No initrd | |
## Transferring control to Linux (at address 80243330) ... | |
## Giving linux memsize in MB, 32 | |
Starting kernel ... | |
LINUX started... | |
Linux version 3.4.113 (padavan@hms) (gcc version 7.5.0 (crosstool-NG UNKNOWN) ) #1 Fri Aug 7 18:16:31 +06 2020 | |
MediaTek SoC: MT7620N, RevID: 0206, RAM: DDR1, XTAL: 20MHz | |
CPU/OCP/SYS frequency: 600/200/200 MHz | |
CPU revision is: 00019650 (MIPS 24KEc) | |
Determined physical RAM map: | |
memory: 02000000 @ 00000000 (usable) | |
Zone PFN ranges: | |
Normal | |
0x00000000 -> 0x00002000 | |
Movable zone start PFN for each node | |
Early memory PFN ranges | |
0: 0x00000000 -> 0x00002000 | |
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. | |
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | |
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 8128 | |
Kernel command line: console=ttyS0,57600n8 | |
PID hash table entries: 128 (order: -3, 512 bytes) | |
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) | |
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) | |
Writing ErrCtl register=000783fa | |
Readback ErrCtl register=000783fa | |
Memory: 29484k/32768k available (2339k kernel code, 3284k reserved, 335k data, 204k init, 0k highmem) | |
NR_IRQS:40 | |
console [ttyS0] enabled | |
Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) | |
pid_max: default: 32768 minimum: 301 | |
Mount-cache hash table entries: 512 | |
NET: Registered protocol family 16 | |
bio: create slab <bio-0> at 0 | |
Switching to clocksource MIPS | |
NET: Registered protocol family 2 | |
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | |
TCP established hash table entries: 1024 (order: 1, 8192 bytes) | |
TCP bind hash table entries: 1024 (order: 0, 4096 bytes) | |
TCP: Hash tables configured (established 1024 bind 1024) | |
TCP: reno registered | |
UDP hash table entries: 256 (order: 0, 4096 bytes) | |
NET: Registered protocol family 1 | |
squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
msgmni has been set to 57 | |
io scheduler noop registered (default) | |
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled | |
serial8250: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A | |
Ralink GPIO driver initialized. Number of GPIO: 73, GPIO mode: 007A811D | |
loop: module loaded | |
Ralink SPI flash driver, SPI clock: 50MHz | |
SPI flash chip: MX25L3205D (c2 2016c220) (4096 Kbytes) | |
raspi: error parsing Firmware partition | |
Ralink APSoC Ethernet Driver v3.2.4 (raeth) | |
raeth: PDMA RX ring 256, PDMA TX ring 512. Max packet size 1536 | |
raeth: NAPI support, weight 32 | |
raeth: Byte Queue Limits (BQL) support | |
PPP generic driver version 2.4.2 | |
PPP MPPE Compression module registered | |
NET: Registered protocol family 24 | |
PPTP driver version 0.8.5 | |
nf_conntrack version 0.5.0 (8192 buckets, 16384 max) | |
xt_time: kernel timezone is -0000 | |
Bridge firewalling registered | |
gre: GRE over IPv4 demultiplexor driver | |
ip_tables: (C) 2000-2006 Netfilter Core Team | |
TCP: cubic registered | |
NET: Registered protocol family 10 | |
ip6_tables: (C) 2000-2006 Netfilter Core Team | |
IPv6 over IPv4 tunneling driver | |
NET: Registered protocol family 17 | |
L2TP core driver, V2.0 | |
PPPoL2TP kernel driver, V2.0 | |
8021q: 802.1Q VLAN Support v1.8 | |
ASUS NVRAM, v0.08. Available space: 61440. Integrity: MTD is empty | |
VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 | |
Please append a correct "root=" boot option; here are the available partitions: | |
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment