efsprofiles/overideconfig

overideconfig

[SIPConfig:GeoLocation]

#enable or disable location info inclusion in regular calls

iEnableCellInfoInPANI = 0

#enable or disable location info inclusion in regular calls

iEnableLocInfoInNormalCall = 0

#enable or disable location info inclusion in emergency calls

iEnableLocInfoInEmergencyCall = 1

#to set the threshold for uncertainty validation

fUnCertaintyThreshold = 0.0


[QIPCALL:H264_2]

#This config is to specify the profile for H264. Only use value 1

profile = 1

#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION,    // 1
#LANDSCAPE_SQCIF_RESOLUTION,   // 2
#PORTRAIT_QQVGA_RESOLUTION,    // 3
#LANDSCAPE_QQVGA_RESOLUTION,   // 4
#PORTRAIT_QCIF_RESOLUTION,     // 5
#LANDSCAPE_QCIF_RESOLUTION,    // 6
#PORTRAIT_QVGA_RESOLUTION,     // 7
#LANDSCAPE_QVGA_RESOLUTION,    // 8
#PORTRAIT_CIF_RESOLUTION,      // 9
#LANDSCAPE_CIF_RESOLUTION,     // 10
#PORTRAIT_VGA_RESOLUTION,      // 11
#LANDSCAPE_VGA_RESOLUTION,     // 12
#PORTRAIT_HD_720_RESOLUTION,   // 13
#LANDSCAPE_HD_720_RESOLUTION,  // 14

resolution_preferred = 8

#Preffered Framerate

framerate_preferred = 15

#payload type for packetization mode 0. number above 96

payload_type_packetization_mode0 = 117

#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10

level = 4

#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0

payload_type_packetization_mode1 = 118

#AS value if IPv6 is used

ipv6_AS_value = 0

#Max Bitrate

bitrate_max = 335

#Preffered bitrate

bitrate_preferred = 335

#Min Bitrate

bitrate_min = 64

#Max Framerate

framerate_max = 15

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'

#Min Framerate

framerate_min = 7

#Supported resolution

resolutions_supported = 0

#AS value if IPv4 is used

ipv4_AS_value = 0


[QIPCALL:H264_1]

#This config is to specify the profile for H264. Only use value 1

profile = 1

#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION,    // 1
#LANDSCAPE_SQCIF_RESOLUTION,   // 2
#PORTRAIT_QQVGA_RESOLUTION,    // 3
#LANDSCAPE_QQVGA_RESOLUTION,   // 4
#PORTRAIT_QCIF_RESOLUTION,     // 5
#LANDSCAPE_QCIF_RESOLUTION,    // 6
#PORTRAIT_QVGA_RESOLUTION,     // 7
#LANDSCAPE_QVGA_RESOLUTION,    // 8
#PORTRAIT_CIF_RESOLUTION,      // 9
#LANDSCAPE_CIF_RESOLUTION,     // 10
#PORTRAIT_VGA_RESOLUTION,      // 11
#LANDSCAPE_VGA_RESOLUTION,     // 12
#PORTRAIT_HD_720_RESOLUTION,   // 13
#LANDSCAPE_HD_720_RESOLUTION,  // 14

resolution_preferred = 8

#Preffered Framerate

framerate_preferred = 15

#payload type for packetization mode 0. number above 96

payload_type_packetization_mode0 = 115

#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10

level = 4

#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0

payload_type_packetization_mode1 = 116

#AS value if IPv6 is used

ipv6_AS_value = 0

#Max Bitrate

bitrate_max = 335

#Preffered bitrate

bitrate_preferred = 335

#Min Bitrate

bitrate_min = 64

#Max Framerate

framerate_max = 15

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'

#Min Framerate

framerate_min = 7

#Supported resolution

resolutions_supported = 0

#AS value if IPv4 is used

ipv4_AS_value = 0


[QIPCALL:H264_0]

#This config is to specify the profile for H264. Only use value 1

profile = 1

#Preffered resolution. Possible values:
#INVALID_RESOLUTION = 0,
#PORTRAIT_SQCIF_RESOLUTION,    // 1
#LANDSCAPE_SQCIF_RESOLUTION,   // 2
#PORTRAIT_QQVGA_RESOLUTION,    // 3
#LANDSCAPE_QQVGA_RESOLUTION,   // 4
#PORTRAIT_QCIF_RESOLUTION,     // 5
#LANDSCAPE_QCIF_RESOLUTION,    // 6
#PORTRAIT_QVGA_RESOLUTION,     // 7
#LANDSCAPE_QVGA_RESOLUTION,    // 8
#PORTRAIT_CIF_RESOLUTION,      // 9
#LANDSCAPE_CIF_RESOLUTION,     // 10
#PORTRAIT_VGA_RESOLUTION,      // 11
#LANDSCAPE_VGA_RESOLUTION,     // 12
#PORTRAIT_HD_720_RESOLUTION,   // 13
#LANDSCAPE_HD_720_RESOLUTION,  // 14

resolution_preferred = 7

#Preffered Framerate

framerate_preferred = 15

#payload type for packetization mode 0. number above 96

payload_type_packetization_mode0 = 113

#Codec level. possible values:
#INVALID_LEVEL = 0x00,
#Level 1 = 0x01,
#Level 1B = 0x02,
#Level 11 = 0x03,
#Level 12 = 0x04,
#Level 13 = 0x05,
#Level 2 = 0x06,
#Level 21 = 0x07,
#Level 22 = 0x08,
#Level 3 = 0x09,
#Level 31 = 0x0A,
#Level 32 = 0x0B,
#Level 4 = 0x0C,
#Level 41 = 0x0D,
#Level 42 = 0x0E,
#Level 5 = 0x0F,
#Level 51 = 0x10

level = 4

#payload type for packetization mode 1. number above 96 and
#different from packetization mode 0

payload_type_packetization_mode1 = 114

#AS value if IPv6 is used

ipv6_AS_value = 0

#Max Bitrate

bitrate_max = 384

#Preffered bitrate

bitrate_preferred = 384

#Min Bitrate

bitrate_min = 64

#Max Framerate

framerate_max = 15

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'

#Min Framerate

framerate_min = 7

#Supported resolution

resolutions_supported = 0

#AS value if IPv4 is used

ipv4_AS_value = 0


[QIPCALL:EVS_0]

#channel aware setting

ch_aw_recv = 2

#This config is used for hf only

hf_only = 0

#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,

Bandwidth = BandWidth_NB_WB

#This config is used for bit rate. It has to be in DECIMAL format.

BitRate = 127


[QIPCALL:EVS_1]

#channel aware setting

ch_aw_recv = 2

#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,

Bandwidth = BandWidth_SWB

#This config is used for bit rate.

BitRate = 120


[QIPCALL:EVS_2]

#channel aware setting

ch_aw_recv = -1

#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,

Bandwidth = BandWidth_WB

#This config is used for bit rate.

BitRate = 120


[SMSDAN:USSDSettings]

#This config item controls the Language String to be used.

ussdLangString = ""


[QIPCALL:H265_2]

#payload type for packetization mode 0. number above 96

payload_type = 0

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'


[Registration:RegistrationTimers]

#This config item controls the time in seconds to wait for WLAN RAT in wifi preferred mode for SSIM device

wlanGaurdTimer = 7

#This config item controls the Register configuration for the network-initiated De reg Timer value.

networkInitiatedDeRegistrationTimer = 0

#This config item controls the Retry timer for permanent PDP failures

pdnRetryLongTimer = 5

#This config item controls the time in seconds to wait for WLAN RAT in wifi preferred mode for MSIM device

wlanGaurdTimerMSIM = 7

#This config item controls the time in seconds to wait for WWAN RAT in cellular preferred mode for SSIM device

wwanGaurdTimer = 7

#This config item controls the time in seconds for epDN retry procedures

ePDNDefaultRetryTimerVal = 0

#This config item controls the time in seconds to wait for WWAN RAT in cellular preferred mode for MSIM device

wwanGaurdTimerMSIM = 10

#This config item controls the time in seconds for emergency registration procedure to complete before declaring failure

timerE1 = 0

#This config item controls the  Retry timer for temporary failures

pdnRetryShortTimer = 60


[QIPCALL:H265_0]

#payload type for packetization mode 0. number above 96

payload_type = 0

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'


[QIPCALL:H265_1]

#payload type for packetization mode 0. number above 96

payload_type = 0

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'


[Ut:UtConfiguration]

#This config is required to configure the server responses for which UT is to be blocked permanently

BlockUtResponseCodes = ""

#This config item controls the media element type for Call Barring Service. 0:No media tag support, 1:One media tag per media type, 2: include both audio and video tags

mediaElementSupportForCB = 0

#This config item specifies if the realm is to trimmed or not. 0:Not enabled(default),  1:enabled

isTrimRealmEnabled = 0

#This config item specifies if IR92v10 is enabled or not. 0:Not enabled(default),  1:enabled

isIr92V10Enabled = 0

#This config item controls the time for which the PDN needs to be kept Active after a SS request is completed

*pdnHysTimerValue = 240

#This config item controls the Maximum time within which a Response should be sent to UI

*maxResponseTimerValue = 30

#This config item controls the action item when there is no SIB value for CB request. 0:Default, 1:Reject, 2:Audio Only, 3:Both Audio and Video

emptySIBUsageForCB = 0

#This config item controls the action item. When a rule id is not present in a server xml, a request is not allowed. It is used on VDF-Portugal only now. 0:Not to check a rule ID(Default),  1:Block a request when rule ID is not present in a server xml

blockIfRuleIDAbsent = 0


[SIPConfig:FeatureFlags]

#enable or disable sip instance inclusion in contact header

IsSipInstanceNeeded = 0

#enable or disable Cellular-Network-Info header

IsCNIEnabled = 1

#enable or disable header compact form

IsCompactFormEnabled = 0

#enable or disable IsUIReadyStatusCheckNeeded

IsUIReadyStatusCheckNeeded = 0

#disable StopTimerBon1xx once 1xx response is not received

StopTimerBon1xx = 0

#enable or disable IsImsiNeededForContactHeader

IsImsiNeededForContactHeader = 0


[QIPCALL:ImsVoiceSrvccConfig]

#This config is required to enable bSRVCC.

bSrvccEnabled = 1

#This config is required to enable aSRVCC.

aSrvccEnabled = 1

#This config is required to enable mid call SRVCC.

midcallSrvccEnabled = 1


[QIPCALL:ImsRtcpConfig]

#This config is required to configure the RR bandwidth for Video.

rrForVideo = 2000

#This config is required to configure the timer for RTCP
#monitoring.

rtcpLinkAlivenessTimer = 20

#This config is required to configure the RS bandwidth for Audio.

rsForAudio = 600

#This config is required to disbale/enable the RTCP monitoring.

disableRTCPMonitoring = 0

#This config is required to configure the timer for RTCP
#Reporting in VT call.

rtcpReportingIntervalInVideo = 1

#This config is required to configure the RS bandwidth for Video.

rsForVideo = 600

#This config is required to configure the RR bandwidth for Audio.

rrForAudio = 2000


[QIPCALL:AMR_4]

#This config is bandwidth.
#enum - BW_NW, BW_WB

BandWidth = BandWidth_WB

#This config is modeset.

ModeSet = 0

#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA

Mode = AMR_MODE_OA


[QIPCALL:G711_2]

#This config is dtx.
#0 - dtx disable
#1 - dtx enable

Dtx_enable = 1

#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA

Mode = G711_MODE_PCMA


[QIPCALL:G711_1]

#This config is dtx.
#0 - dtx disable
#1 - dtx enable

Dtx_enable = 1

#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA

Mode = G711_MODE_PCMU


[QIPCALL:G711_0]

#This config is dtx.
#0 - dtx disable
#1 - dtx enable

Dtx_enable = 1

#This config is to set G711 mode
#enum - G711_MODE_PCMU, G711_MODE_PCMA

Mode = G711_MODE_PCMU


[QIPCALL:AMR_0]

#This config is bandwidth.
#enum - BW_NW, BW_WB

BandWidth = BandWidth_NB

#This config is modeset.

ModeSet = 0

#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA

Mode = AMR_MODE_BE


[QIPCALL:AMR_1]

#This config is bandwidth.
#enum - BW_NW, BW_WB

BandWidth = BandWidth_WB

#This config is modeset.

ModeSet = 0

#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA

Mode = AMR_MODE_BE


[QIPCALL:AMR_2]

#This config is bandwidth.
#enum - BW_NW, BW_WB

BandWidth = BandWidth_NB

#This config is modeset.

ModeSet = 0

#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA

Mode = AMR_MODE_OA


[QIPCALL:AMR_3]

#This config is bandwidth.
#enum - BW_NW, BW_WB

BandWidth = BandWidth_NB

#This config is modeset.

ModeSet = 0

#This config is mode.
#enum - AMR_MODE_BE, AMR_MODE_OA

Mode = AMR_MODE_BE


[QIPCALL:ImsVoiceQoSConfig]

#This config is required to enable sending SDP answer in PRACK
#for 183 if the local qos is granted before 183 response is recvd by
#the UE.

qosOptimization = 0

#This config is required to configure the timer for dedicated
#bearer allocation.

qosReservationTimer = 8000

#This config is required to enable set the desired qos strength
#for local and remote UEs.

qosDesiredStrength = 1

#This config is required to enable 183 for Reneg

qosMc183 = 0

#This config is required to configure if the UE must wait for
#video dedicated bearer allocation during call setup.

localQosResReqVideo = 1

#This config is required to configure if the UE must wait for
#text dedicated bearer allocation during call setup.

localQosResReqText = 1

#This config is required to enable/disable video CRBT feature

VideoCRBT = 0

#This config is required to configure the early QoS timer for video dedicated
#bearer allocation.

earlyQosReservationTimer = 0

#This config is required to enable Qos precondition negotiation
#in SDP.

qosPreconditionsEnabled = 1

#This config is required to enable Qos MC precondition negotiation
#in SDP.

qosMcPreconditionsEnabled = 0

#This config is required to configure the MBR threshold.

iMBRthresholdValue = 0

#This config is required to configure if the UE must wait for
#audio dedicated bearer allocation during call setup.

localQosResReqAudio = 1

#This config is required to configure if the initial SDP
#directionality should be inactive in REINVITE when preconditions are
#used

reinviteSdpDirInactive = 0

#This config is required to enable MBR check for video bearer.

qosMbrVideoCheckReqEnabled = 1

#This config is required to configure if the initial SDP
#directionality should be inactive when preconditions are used.

inviteSdpDirInactive = 0

#This config is required to enable MBR check for audio bearer.

qosMbrAudioCheckReqEnabled = 0

#This config is required to enable QCI match with the requested media type for qos

checkQciForQoSMediaType = 0

#This config is required to enable mid-call precondition for Call Hold/Resume

qosMcHold = 0


[Ut:XCAPCommonHC]

#This config item controls the configuration of BSF server address

bsfServerAddress = ""

#This config item controls whether to ignore RSp Auth failure or not

IgnoreRSPAuthFailure = 0

#This config item controls whether GBA_U is enabled or not

*useGBAMEOnly = 1

#This config item controls whether ims prefix is added or not for Ub request like as bsf.ims.mnc005.mcc232.pub.3gppnetwork.org

includeIMSPrefixForUSIM = 0

#This config item controls whether BSF server supports TLS

bsfServerTlsSupport = 0


[Registration:RegistrationFeatureFlags]

#This config item specifies if the sub operator is APTG and special handling is required for Options unsubscribed error or not. 0:Not enabled(default),  1:enabled

optionsUnsubscribedSpecialHandling = 0

#This config item controls whether need to reset AWT timer.

notResetAWTTimerEnable = 0

#This config item controls whether IWLAN Config failure is to be handled as internal failure.

specialhandlingForIWLANConfigFailure = 0


[QIPCALL:EVS_3]

#channel aware setting

ch_aw_recv = 2

#This config is bandwidth.
#enum - BW_NB, BW_WB, BW_SWB, BW_FB, BW_NB_WB, BW_NB_SWB, BW_NB_FWB,

Bandwidth = BandWidth_WB

#This config is used for bit rate.

BitRate = 120


[QIPCALL:ImsVoiceSessionTimerConfig]

#This config is required to configure the session refresher shall
#be UAC/UAS.

sessionRefresherType = QP_CONFIG_SES_REFRESHER_UAC

#This config is required to enable session timer support.

sessionTimerEnabled = 1

#This config is required to enable Stand Alone Session Expiry
#negotiation.

standAloneEnabled = 1

#This config is required to enable Sesssion Expiry timer
#negotiation.

allowSeNegotiation = 0

#This config is required to configure the method for session
#referesh shall be REINVITE/UPDATE.

sessionRefresherMethod = QP_CONFIG_SES_REFRESH_UPDATE


[QIPCALL:ImsVoiceConfig]

#This config is required to configure the Emergency call Cancel Timer.TImer is started when UE triggered CANCEL and waiting for 200 OK of CANCEL from network

emergencyCallCancelTimer = 500

#This config is required to configure the default WPS invite duration.

wpsInviteDuration = 0

#This config is required to enable 380 response validation as per
#3GPP.

*enableAlternateSrvRspCheck = 0

#This config is required to set the display text priority
#subscription.

displayTextPriority = 1

#This config is required to include MTT USSD feature tag into IMS registration.

ussdAcceptContact = "+g.3gpp.nw-init-ussi"

#This config is required to configure the default invite retry counter.

inviteRetryCounter = 2

#This config is required to select the default emergency URI if sub category matches with multiple entries

e911SelectDefURI = 0

#This config is required to disable early media timer.

disableEarlyMediaTimer = 0

#This config is required to configure the voice call Cancel Timer.TImer is started when UE triggered CANCEL and waiting for 200 OK of CANCEL from network

voiceCallCancelTimer = 0

#This config is required to place AMR WB before AMR in encryption call.

preferAMRWBinEncryptionCall = 0

#This config is required to enable PEM header in 183.

enablePEMHeaderIn183 = 0

#This config is required to configure the default URI type
#(SIP/TEL) for MO calls.

uriType = QPE_IMS_URI_ANY

#This config is required to configure the enabling of sending REINVITE
#during Active calls HO.

reInviteonHOforActiveCalls = 0

#This config is required to configure the terminating identity presentation or restriction type.

terminatingIdentityService = 0

#This config is required to configure the default WPS fallback duration.

wpsFallbackDuration = 0

#This config is required to configure the ignoring of AS value

ignoreASValidation = 0

#This config is required to configure the max-red value

max_red = 0

#This config is required to set error code for CT submode.

sessionEndResponseTimeout = 0

#This config is required to enable VoWIFI Call Continuity to LTE NonVOPS.

enableVCCtoLTENonVOPS = 0

#This config is required to enable emergency call operation in CS-only mode.

emergCallCSOnly = 0

#This config is required to configure number format during roaming, geo-local/home-local

phoneContextPolicy = QPE_IMS_PHONE_CONTEXT_GEO_LOCAL

#This config is required to enable Call end on RTP inactivity.

CallEndonRTPInactivity = 0

#This config is required to set the phone context domain source.

PhoneContextSource = QPE_IMS_PHONE_CONTEXT_SOURCE_FROM_PAU_HEADER

#This config is required to set preconditions enabled with qos events ignored.

ignoreQOSEvents = 0

#This config is required to enable the MT USSI.

enableMTUSSI = 1

#This config is required to configure the privacy type. Set 0: for none, 1: for id, 2: for header.

privacyType = 2


[Registration:RegistrationDefaultParams]

#This config item will be used to configure default UserName to register with Network

userName = ""

#This config item will be used to configure default authType to register with Network

authType = ""

#This config item will be used to configure default Display Name to register with Network

displayName = ""

#This config item will be used to configure default DomainName to register with Network

domainName = ""

#This config item will be used to configure default authSecertKey

authSecertKey = "465b5ce8b199b49faa5f0a2ee238a6bc"

#This config item will be used to configure default Private URI to register with Network

privateURI = ""

#This config item will be used to configure default is3GPP

is3GPP = 0

#This config item will be used to configure default Realm to register with Network

realm = ""

#This config item will be used to configure default public URI to register with Network

publicURI = ""

#This config item will be used to configure default Password to register with Network

password = ""


[QIPCALL:ImsVoiceSuppsConfig]

#This config is required to configure the timer for Notify
#response to Refer.

notifyReferRspTimer = 20

#This config is required to end the conference call automatically
#when all other participants left the call.

endConfCallUponNoParticipant = 1

#This config is required to enable presentation of the call to
#the user when UE is already in two calls (active and held).

presentThirdCalltoUser = 1

#This config is required to configure the conference event
#package subscription timer.

confEvtSubTimer = 3600

#This config is required not to send unsubscribe to NW  for conference call when there is
#no notify-terminated received.

isUnsubcribeDisabled = 0

#This config is required to configure the dialog for the
#conference event subscribe request.

*confEvtSubOutOfDialog = 0

#This config is required to configure the three party conf URI
#for KDDI.

threePartyConfFactoryUri = ""

#This config is required to enable the conference event package
#subscription.

confEvtPakageEnabled = QPE_IMS_CONF_PCKG_ALL


[QIPCALL:ImsRtcpXRConfig]

#This config is required to enable RTCP-XR support.

rtcpXrEnabled = 0


[SMSDAN:DANSettings]

#This config item controls QIPCall 1x SMS and Voice Enabled (0:DAN SMS can be sent only if there is no voice call.
#1:Enabled; DAN and MO SMS can be sent even when a voice call is up).

smsAndVoiceOver1x = 0

#This NV item is used for configuring the transport channel preference on which DAN is to be sent.

channelPreference = 0

#This config item controls the DAN Retry Timer Interval Duration (In ms)

retryTimer = 0

#This config item controls the DAN Max Retry Counter

maxRetryCount = 0

#This NV item is used for controlling DAN Hysterisis Timer Duration

hysterisisTimer = 0


[QIPCALL:H263_0]

#payload type number above 96

payload_type = 0

#This config is to ensure if the configuration is included in the
#offer

exclude_config_from_offer = '0'


[Registration:RegistrationCounters]

#This config item controls the Immediate  Retry timer for failures

maxPDNIntermediateRetries = 1


[QIPCALL:ImsVideoConfig]

#This config is required to configure the LTR mode.

ltrMode = QP_CONFIG_IMS_LTR_DISABLED

#This config is required to configure if VT capability can be impacted by modile data.

vtImpactedByMobileData = 1

#This config is required to set the video_capability_for_invite_no_sdp for
#incoming INVITE without SDP.

video_capability_for_invite_no_sdp = 1

#Internal:This config is required to store peer supported
#services

trackPeerServices = 0


[SIPConfig:Transport]

#above this size choose TCP and value 0 means disable tcp port open on UE

*TCPThresholdValue = 1480

#enable or disable TCP Static threshold

*TCPEnableStaticThreshold = 1


[SIPConfig:StandardTimers]

#sip registration expires value

*SipRegValue = 600000

#sip reg subscription expires value

*SipSubscribeValue = 600000


[SIPConfig:IPSec]

#integrity scheme for ipsec sip messages

IntScheme = 3

#encryption algo for ipsec sip messages

EncAlgo = 7


[SMSDAN:SMSSettings]

#This config item used to configure the error code and used while reject Incoming MT sms while NAS is busy in service one SMS.

IncomingSmsRejectCode = 400

#This config item used to enable or disable feature of rejecting incoming SMS when IMS is already processing a SMS.

EnableIncomingSmsRejectFeature = 0

#This config item controls the SMS Feature tag

smsAcceptContact = "+g.3gpp.smsip"


[MEDIA:MediaCommon]

#This config item specifies if overall rate adaptation feature is enabled or not.

audioRAEnable = 1

#This config item specifies maximum mtu size for the rtp packet

*mtuSize = 1200


[Registration:RegistrationSettings]

#This config item controls Registration over IWLAN in airplane mode

enableRegistrationInLPM = 2

#This config item controls PCSCF IP fallback feature

pcscfBasedIPFallback = 0

#This config item controls TTY over IMS

enableTTYOverIMS = 0

#This config item controls Reregistration over WIFI during Activate 3G call

BlockRegOverWifiWhileActiveCSCall = 1

#This config item controls Reregistration over WIFI during Activate 1x call

BlockRegOverWifiWhileActive1XCall = 0


[Ut:XcapHCConfigUserProfile]

#This config item controls the configured user name

configUserName = ""

#This config item controls the configured user name

configUserPassword = ""


[DPL:Common]

#This config item determines usage to read the SIM card parameters (ISIM, USIM ) etc
#Possible INTEGER values for override are as follows:
#QPE_CONFIG_IMS_FILE_READ              = 0 --> File Read Param Source
#QPE_CONFIG_IMS_NV_READ                = 1 --> NV Read Param Source
#QPE_CONFIG_IMS_CARD_READ              = 2 --> Card Read Param Source to read from ISIM
#QPE_CONFIG_IMS_FILE_READ_AUTH_ENABLED = 3 --> File Read Param Auth enabled (ONLY for testing)
#QPE_CONFIG_IMS_USIM_FB_MODE_ENABLED   = 4 --> USIM fallback enabled

ParamSrc = QPE_CONFIG_IMS_USIM_FB_MODE_ENABLED


[QIPCALL:ImsMediaProfileConfig]

#This config is required to video codec profile list on 4G.

VideoProfile1 = "H264_0"

#This config is required to audio codec profile list.

*AudioProfile1 = "EVS_1_127;EVS_0_126;AMR_1_104;AMR_0_102"


[QIPCALL:ImsVoWifiConfig]

#This config is required to configure the wifi connectivity
#backoff timer.

wifiConnectivityBackoffTimer = 10

#This config is required to configure the 380 handling for Emergency calls
#Possible values are:
#0 -> Default behaviour present in the code
#1 -> Force CSFB
#2 -> Send Permanent failure

Handling380forEmergency = 0


[MEDIA:MediaDscp]

#This config item specifies dscp value for audio

audio = 46

#This config item specifies dscp value for video

video = 46


[QIPCALL:ImsVideoModifyConfig]

#This config is required to configure the timer in msecs for
#waiting on user response to the incoming upgrade req.

localUpgradeAcceptTimer = 20000

#This config is required to configure the timer in secs for
#response from the peer to the sent upgrade req.

remoteUpgradeRejectTimer = 40


[QIPCALL:ImsEmergencyConfig]

#This config is required to configure the timer for dedicated
#bearer allocation for E911 call.

emerQosReservationTimer = 8000

#This config is required to configure whether UE needs to end e911 call based on RTP/RTCP timeout for audio

KeepE911CallOnAudioRTPRTCPTimeOut = 0


[SIPConfig:CustomTimers]

#reliable response retry timer cap

TRelResponseRetry = 0