haproxy.cfg

global
	log 127.0.0.1	local0
	log 127.0.0.1	local1 notice
	#Adds a global syslog server. Up to two global servers can be defined. They
  	#will receive logs for startups and exits, as well as all logs from proxies
  	#configured with "log global". An optional level can be specified to filter 
	#outgoing messages. By default, all messages are sent.
	
        #An IPv4 address optionally followed by a colon and a UDP port. If
        #no port is specified, 514 is used by default (the standard syslog port).

	maxconn 4096
	#Sets the maximum per-process number of concurrent connections to <number>. It
 	#is equivalent to the command-line argument "-n". Proxies will stop accepting
 	#connections when this limit is reached. The "ulimit-n" parameter is
 	#automatically adjusted according to this value. See also "ulimit-n"

	uid 99
	#Changes the process' user ID to <number>. It is recommended that the user ID
	#is dedicated to HAProxy or to a small set of similar daemons. HAProxy must
	#be started with superuser privileges in order to be able to switch to another
	#one. See also "gid" and "user".

	gid 99
	#Changes the process' group ID to <number>. It is recommended that the group
	#ID is dedicated to HAProxy or to a small set of similar daemons. HAProxy must
	#be started with a user belonging to this group, or with superuser privileges.
	#See also "group" and "uid".

	daemon
	#Makes the process fork into background. This is the recommended mode of
 	#operation. It is equivalent to the command line "-D" argument. It can be
  	#disabled by the command line "-db" argument.

	#debug
        #NO NEED TO ENABLE - krams
	#Enables debug mode which dumps to stdout all exchanges, and disables forking
	#into background. It is the equivalent of the command-line argument "-d". It
	#should never be used in a production configuration since it may prevent full
	#system startup.

	#quiet
        #NO NEED TO ENABLE - krams
	#Do not display any message during startup. It is equivalent to the command-
 	#line argument "-q".

defaults
	log	global
	#Enable per-instance logging of events and traffic.
	#global should be used when the instance's logging parameters are the
	#same as the global ones. This is the most common usage. "global"
	#replaces <address>, <facility> and <level> with those of the log
	#entries found in the "global" section. Only one "log global"
	#statement may be used per instance, and this form takes no other
	#parameter.

	mode	http
	#Set the running mode or protocol of the instance
	#The instance will work in HTTP mode. The client request will be
	#analyzed in depth before connecting to any server. Any request
	#which is not RFC-compliant will be rejected. Layer 7 filtering,
	#processing and switching will be possible. This is the mode which
	#brings HAProxy most of its value.

	option	httplog
	#Enable logging of HTTP request, session state and timers

	option	dontlognull
	#Enable or disable logging of null connections

	retries	3
        #Set the number of retries to perform on a server after a connection failure

	option redispatch
        #Enable or disable session redistribution in case of connection failure

	maxconn	2000
	#Fix the maximum number of concurrent connections on a frontend
	#This value should not exceed the global maxconn

	contimeout	5000
	#Set the maximum time to wait for a connection attempt to a server to succeed.

	clitimeout	50000
	#Set the maximum inactivity time on the client side.
	#An unspecified timeout results in an infinite timeout, which
  	#is not recommended. Such a usage is accepted and works but reports a warning
  	#during startup because it may results in accumulation of expired sessions in
  	#the system if the system's timeouts are not configured either.

	srvtimeout	50000
	#Set the maximum inactivity time on the server side.

	#balance roundrobin
        #NO NEED TO ENABLE. IT'S THE DEFAULT - krams
	#The load balancing algorithm of a backend is set to roundrobin when no other
  	#algorithm, mode nor option have been set

frontend http-in 
	bind *:80
	#Define one or several listening addresses and/or ports in a frontend

        default_backend servers
	#Specify the backend to use when no "use_backend" rule has been matched
       
backend servers 
        option httpchk OPTIONS /
	#Enable HTTP protocol to check on the servers health

	option forwardfor
	#Enable insertion of the X-Forwarded-For header to requests sent to servers
 	#Since HAProxy works in reverse-proxy mode, the servers see its IP address as
 	#their client address. This is sometimes annoying when the client's IP address
  	#is expected in server logs. To solve this problem, the well-known HTTP header
  	#"X-Forwarded-For" may be added by HAProxy to all requests sent to the server.

        stats enable
	#Enable statistics reporting with default settings

        stats refresh 10s
	#Enable statistics with automatic refresh

        stats hide-version
	#Enable statistics and hide HAProxy version reporting

        stats scope   .
	# Enable statistics and limit access scope

        stats uri     /admin?stats
	#Enable statistics and define the URI prefix to access them

        stats realm   Haproxy\ Statistics
	#Enable statistics and set authentication realm
	#<realm>   is the name of the HTTP Basic Authentication realm reported to
	#the browser. The browser uses it to display it in the pop-up
	#inviting the user to enter a valid username and password.

        stats auth    admin:pass
	#Enable statistics with authentication and grant access to an account
	
	cookie JSESSIONID prefix
	#Enable cookie-based persistence in a backend
	#server <name> <address>[:port] [param*]
	#Please refer to section 5 for more details.

	server tomcat1 127.0.0.1:8080 cookie JSESSIONID_SERVER_1 check inter 5000
  	server tomcat2 127.0.0.1:8180 cookie JSESSIONID_SERVER_2 check inter 5000
        #Declare a server in a backend
        #server <name> <address>[:port] [param*]
        #<param*>  is a list of parameters for this server. The "server" keywords
        #accepts an important number of options and has a complete section
        #dedicated to it. Please refer to section 5 for more details.