hdd-smart.log

smartctl 6.4 2015-06-04 r4109 [armv7l-linux-4.3.3-1-ARCH] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     HGST Travelstar 5K1000
Device Model:     HGST HTS541010A9E680
Serial Number:    
LU WWN Device Id: 
Firmware Version: JA0OA560
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Tue Jan 12 01:07:47 2016 HKT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(   45) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 222) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   062    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   040    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0007   253   253   033    Pre-fail  Always       -       1
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       34
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   040    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   099   099   000    Old_age   Always       -       562
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       34
191 G-Sense_Error_Rate      0x000a   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       22
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       6012
194 Temperature_Celsius     0x0002   230   230   000    Old_age   Always       -       26 (Min/Max 19/44)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       75
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0
223 Load_Retry_Count        0x000a   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 28 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 28 occurred at disk power-on lifetime: 421 hours (17 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  10 51 10 10 5c a1 05  Error: IDNF at LBA = 0x05a15c10 = 94460944

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 20 10 00 5c a1 40 00      00:11:24.320  READ FPDMA QUEUED
  27 00 00 00 00 00 e0 00      00:11:24.312  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:11:24.311  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:11:24.311  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:11:24.311  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 27 occurred at disk power-on lifetime: 421 hours (17 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  10 51 08 18 5c a1 05  Error: IDNF at LBA = 0x05a15c18 = 94460952

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 20 00 00 5c a1 40 00      00:11:20.561  READ FPDMA QUEUED
  61 00 f0 c8 bb 74 40 00      00:11:12.004  WRITE FPDMA QUEUED
  61 00 e8 d0 9d 74 40 00      00:11:11.992  WRITE FPDMA QUEUED
  60 20 e0 20 68 b7 40 00      00:11:11.985  READ FPDMA QUEUED
  61 00 d8 c8 bb 74 40 00      00:11:11.975  WRITE FPDMA QUEUED

Error 26 occurred at disk power-on lifetime: 381 hours (15 days + 21 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  10 51 20 20 14 bf 05  Error: IDNF at LBA = 0x05bf1420 = 96408608

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 20 40 20 14 bf 40 00      06:21:13.741  READ FPDMA QUEUED
  61 08 38 98 45 f3 40 00      06:21:13.732  WRITE FPDMA QUEUED
  61 c0 30 d8 42 f3 40 00      06:21:13.714  WRITE FPDMA QUEUED
  61 40 28 98 3d f3 40 00      06:21:13.698  WRITE FPDMA QUEUED
  61 c0 20 d8 3a f3 40 00      06:21:13.668  WRITE FPDMA QUEUED

Error 25 occurred at disk power-on lifetime: 378 hours (15 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  10 51 20 80 a6 aa 05  Error: IDNF at LBA = 0x05aaa680 = 95069824

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 20 98 80 a6 aa 40 00      03:13:18.797  READ FPDMA QUEUED
  61 c0 90 80 5d ab 40 00      03:13:18.687  WRITE FPDMA QUEUED
  61 40 88 40 58 ab 40 00      03:13:18.550  WRITE FPDMA QUEUED
  61 c0 80 80 55 ab 40 00      03:13:18.238  WRITE FPDMA QUEUED
  61 40 78 40 50 ab 40 00      03:13:18.088  WRITE FPDMA QUEUED

Error 24 occurred at disk power-on lifetime: 377 hours (15 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  10 51 08 80 f9 b6 05  Error: IDNF at LBA = 0x05b6f980 = 95877504

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 88 80 f9 b6 40 00      03:12:51.917  READ FPDMA QUEUED
  61 c0 80 58 7e a7 40 00      03:12:51.897  WRITE FPDMA QUEUED
  61 40 78 18 79 a7 40 00      03:12:51.881  WRITE FPDMA QUEUED
  61 c0 70 58 76 a7 40 00      03:12:51.841  WRITE FPDMA QUEUED
  61 40 68 18 71 a7 40 00      03:12:51.808  WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       525         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.