Skip to content

Instantly share code, notes, and snippets.

@soxrok2212

soxrok2212/Xiaomi Redmi AX6000 Bootlog

Last active September 6, 2022 00:54
Show Gist options
  • Save soxrok2212/03e08ec1879c33fc85c753a72f9a64c0 to your computer and use it in GitHub Desktop.
Save soxrok2212/03e08ec1879c33fc85c753a72f9a64c0 to your computer and use it in GitHub Desktop.
Download ZIP
Raw
Xiaomi Redmi AX6000 Bootlog
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 022F [010F]
Jump to BL
NOTICE: BL2: v2.6(release):2598dbc2a6-dirty
NOTICE: BL2: Built : 13:34:54, Mar 12 2022
INFO: BL2: Doing platform setup
NOTICE: WDT: disabled
NOTICE: CPU: MT7986 (2000MHz)
NOTICE: EMI: Using DDR4 settings
before ctrl3 = 0x0
clear request & ack
after ctrl3 = 0x0
DVFSRC_SUCCESS 0
dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a083f1 000003ff 00100000 00000000
1001d040 | 00000000 00000000 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0x8
toprgu: 80 = 0x0
[DDR Reserve] ddr reserve mode not be enabled yet
Save DRM_DEBUG_CTL(0xa083f1)
DRM_LATCH_CTL : 0x27e71
DRM_LATCH_CTL2: 0x200a0
drm_update_reg: 1, bits: 0x8000, addr: 0x1001d030, val: 0xa083f1
drm_update_reg: 0, bits: 0x80000, addr: 0x1001d030, val: 0xa083f1
drm_update_reg: 0, bits: 0x200, addr: 0x1001d034, val: 0x1ff
drm_update_reg: 0, bits: 0x200000, addr: 0x1001d034, val: 0x1ff
drm_update_reg: 0, bits: 0x100, addr: 0x1001d034, val: 0xff
MTK_DRM_DEBUG_CTL : 0xa083f1
MTK_DRM_DEBUG_CTL2: 0xff
drm_update_reg: 0, bits: 0x4000, addr: 0x1001d030, val: 0xa083f1
DRM DDR reserve mode FAIL! a083f1
DDR RESERVE Success 0
drm_update_reg: 0, bits: 0x2000, addr: 0x1001d030, val: 0xa083f1
drm_update_reg: 0, bits: 0x1000, addr: 0x1001d030, val: 0xa083f1
[DRAM] into mt_set_emi
[EMI] ComboMCP not ready, using default setting
Init_DRAM:2139: init PCDDR4 dram Start
[MD32_INIT] in c code >>>>>>
[MD32_INIT] 3
[MD32_INIT] 4
[MD32_INIT] 5
[MD32_INIT] 6
[MD32_INIT] V22 add 1
[MD32_INIT] V22 add 1 end
[MD32_INIT] 7
[MD32_INIT] 8
[MD32_INIT] 9
[MD32_INIT] 10
[MD32_INIT] 11
[MD32_INIT] 12
[MD32_INIT] 13
[MD32_INIT] 14
[MD32_INIT] 15
[MD32_INIT] 16
[MD32_INIT] 17
[MD32_INIT] 18
[MD32_INIT] 19
[MD32_INIT] 20
[MD32_INIT] 21
[MD32_INIT] 22
[MD32_INIT] 23
[MD32_INIT] 28
[MD32_INIT] 29
[MD32_INIT] 30 for RTMRW, if have
[MD32_INIT] in c code <<<<<<
[Set_DRAM_Pinmux_Sel] DRAMPinmux = 0
[Bian_co] ETT version 0.0.0.1
dram_type 4, R0 cbt_mode 0, R1 cbt_mode 0 VENDOR=136
Read voltage for 1600, 0
Vio18 = 0
Vcore = 0
Vdram = 0
Vddq = 0
Vmddr = 0
== DRAMC_CTX_T ==
support_channel_num: 1
channel: 0
support_rank_num: 1
rank: 0
freq_sel: 22
shu_type: 0
dram_type: 4
dram_fsp: 0
odt_onoff: 1
DBI_R_onoff: 0, 0
DBI_W_onoff: 0, 0
data_width: 16
test2_1: 0x55000000
test2_2: 0xaa000100
frequency: 1600
freqGroup: 1600
u1PLLMode: 0
dram type 6
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
OCD DRVP=0 ,CALOUT=0
OCD DRVP=1 ,CALOUT=0
OCD DRVP=2 ,CALOUT=0
OCD DRVP=3 ,CALOUT=0
OCD DRVP=4 ,CALOUT=0
OCD DRVP=5 ,CALOUT=0
OCD DRVP=6 ,CALOUT=0
OCD DRVP=7 ,CALOUT=0
OCD DRVP=8 ,CALOUT=0
OCD DRVP=9 ,CALOUT=1
OCD DRVP calibration OK! DRVP=9
OCD DRVN=0 ,CALOUT=1
OCD DRVN=1 ,CALOUT=1
OCD DRVN=2 ,CALOUT=1
OCD DRVN=3 ,CALOUT=1
OCD DRVN=4 ,CALOUT=1
OCD DRVN=5 ,CALOUT=1
OCD DRVN=6 ,CALOUT=0
OCD DRVN calibration OK! DRVN=6
[SwImpedanceCal] DRVP=9, DRVN=6
freq_region=0, Reg: DRVP=11, DRVN=8, ODTP=6
MEM_TYPE=6, freq_sel=22
[ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:===================================
PCDDR4 DRAM CONFIGURATION
===================================
CWL = 0x7
RTT_NORM = 0x6
CL = 0xb
AL = 0x0
BL = 0x0
RBT = 0x0
WR = 0x8
===================================
===================================
ANA top config
===================================
ASYNC_MODE = 3
DLL_ASYNC_EN = 1
ALL_SLAVE_EN = 0
NEW_RANK_MODE = 0
DLL_IDLE_MODE = 1
LP45_APHY_COMB_EN = 1
TX_ODT_DIS = 0
NEW_8X_MODE = 0
===================================
===================================
data_rate = 3200
CKR = 1
DQ_P2S_RATIO = 8
===================================
CA_P2S_RATIO = 8
DQ_CA_OPEN = 0
DQ_SEMI_OPEN = 0
CA_SEMI_OPEN = 0
CA_FULL_RATE = 0
DQ_CKDIV4_EN = 0
CA_CKDIV4_EN = 0
CA_PREDIV_EN = 0
PH8_DLY = 31
SEMI_OPEN_CA_PICK_MCK_RATIO= 0
DQ_AAMCK_DIV = 4
CA_AAMCK_DIV = 4
CA_ADMCK_DIV = 4
DQ_TRACK_CA_EN = 0
CA_PICK = 1600
CA_MCKIO = 1600
MCKIO_SEMI = 0
PLL_FREQ = 3200
DQ_UI_PI_RATIO = 32
CA_UI_PI_RATIO = 0
===================================
===================================
memory_type:PCDDR4
GP_NUM : 1
SRAM_EN : 1
MD32_EN : 0
===================================
===========================================
HW_ZQCAL_config
===========================================
ZQCALL is 0
TZQLAT is 27
ZQCSDUAL is 0
ZQCSCNT is 511
===========================================
[ANA_INIT] >>>>>>>>>>>>>>
[ANA_ClockOff_Sequence] flow start
WLY_DEBUG::ANA_ClockOff_Sequence delay 100ns start
WLY_DEBUG::ANA_ClockOff_Sequence delay 100ns end
[ANA_ClockOff_Sequence] flow end
============ PULL DRAM RESETB DOWN ============
========== PULL DRAM RESETB DOWN end =========
============ SUSPEND_ON ============
============ SUSPEND_ON end ============
============ SPM_control ============
============ SPM_control end ============
<<<<<< [CONFIGURE PHASE]: ANA_TX
>>>>>> [CONFIGURE PHASE][SHUFFLE]: PLL
===================================
data_rate = 3200,PCW = 0X7800
===================================
<<<<<< [CONFIGURE PHASE][SHUFFLE]: PLL
INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0
INFO: RG_ARCMD_REV_TEMP_VALUE= 0x0
INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60
>>>>>> [CONFIGURE PHASE][SHUFFLE]: ANA CLOCK DIV configuration
INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 PH8_DLY= 0x1f
INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 PH8_DLY= 0x1f
INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0
INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 PH8_DLY= 0x1f
INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60
INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 PH8_DLY= 0x1f
<<<<<< [CONFIGURE PHASE][SHUFFLE]: ANA CLOCK DIV configuration
>>>>>> [CONFIGURE PHASE][SHUFFLE]: DLL
INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60
INFO: RG_ARCMD_REV_TEMP_VALUE= 0x61
<<<<<< [CONFIGURE PHASE][SHUFFLE]: DLL
[ANA_INIT] flow start
[ANA_INIT] PLL >>>>>>>>
[ANA_INIT] PLL <<<<<<<<
[ANA_INIT] MIDPI >>>>>>>>
[ANA_INIT] MIDPI <<<<<<<<
[ANA_INIT] DLL >>>>>>>>
[ANA_INIT] DLL <<<<<<<<
[ANA_INIT] flow end
[ANA_INIT] <<<<<<<<<<<<<
[Flow] [DDRPHY] DIG_CONFIG_NONSHUF_DCM <<<<<
[Flow] [DDRPHY] DIG_CONFIG_NONSHUF_DCM <<<<<
[Flow] Enable top DCM control >>>>>
[Flow] Enable top DCM control <<<<<
Enable DLL master slave shuffle
==============================================================
Gating Mode config
==============================================================
Config description:
RX_GATING_MODE 0: Pulse Mode 1: Burst Mode(8UI) 2: Burst Mode(7UI) 3: Original Burst Mode
RX_GATING_TRACK_MODE 0: Valid DLY Mode 1: Valid Mode (Jade-like) 2: FIFO mode
SELPH_MODE 0: By rank 1: By Phase
==============================================================
GAT_TRACK_EN = 1
RX_GATING_MODE = 2
RX_GATING_TRACK_MODE = 2
SELPH_MODE = 1
PICG_EARLY_EN = 1
VALID_LAT_VALUE = 0
==============================================================
Enter into Gating configuration >>>>
Exit from Gating configuration <<<<
[DIG_HW_NONSHUF_ZQCAL_CFG],Configuration Enter
[DIG_HW_NONSHUF_ZQCAL_CFG_FOR_PCDDR],Configuration Enter
[DIG_HW_NONSHUF_ZQCAL_CFG],Configuration Enter
[DIG_HW_NONSHUF_ZQCAL_CFG_FOR_PCDDR],Configuration Enter
Enter into PICG configuration >>>>
Exit from PICG configuration <<<<
[DIG_SHUF_CONFIG] DCM_FUNCTION >>>>>>, group_id=0
[DIG_SHUF_CONFIG] DCM_FUNCTION <<<<<<, group_id=0
[DIG_FREQ_CONFIG][TX_CA][Delay] ch_id:0, group_id:0 >>>>>
[DIG_FREQ_CONFIG][TX_CA][Delay] ch_id:0, group_id:0 <<<<<
[DIG_HW_SHUF_ZQCAL_CFG] Group:0, Configuration Enter
[ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:===================================
PCDDR4 DRAM CONFIGURATION
===================================
CWL = 0x7
RTT_NORM = 0x6
CL = 0xb
AL = 0x0
BL = 0x0
RBT = 0x0
WR = 0x8
===================================
[ReadLatency GET] MR_CL:[ReadLatency GET] MR_CL:UI_MCK_least is 1
RX_GW_selph_by_ps[0] is 12464
RX_GW_selph_by_ps[1] is 12464
RX_GW_selph_by_ps[2] is 12464
RX_GW_selph_by_ps[3] is 12464
===================================
RX_path CONFIGURATION
===================================
data_rate is 3200
dq_p2s_ratio is 8
ca_default_delay is 1
ca_ser_latency is 7
cs2RL_start is 1
byte_num is 2
rank_num is 2
RL[0] is 24
RL[1] is 24
RL_min is 24
RL_max is 24
TDQSCK[0] is 0
TDQSCK[1] is 0
TDQSCK[2] is 0
TDQSCK[3] is 0
dqsien_default_delay is 0
dqsien_ser_latency is 7
oe_ser_latency is 4
gating_window_ahead_dqs is 2
aphy_slice_delay is 11
aphy_dtc_delay is 100
aphy_lead_lag_margin is 16
dram_ui_ratio is 2
dq_ui_unit is 312
ca_ui_unit is 312
MCK_unit is 2496
dramc_dram_ratio is 4
CKR is 1
tRPRE_toggle is 0
tRPRE_static is 2
tRPST is 0
DQSIENMODE is 1
BL is 16
FAKE_1TO16_MODE is 0
SVA_1_10_t2_SPEC is 11
read_cmd_out is 1
ca_MCKIO_ui_unit is 312
ca_p2s_ratio is 8
TDQSCK_min_SPEC is 0
TDQSCK_max_SPEC is 360
TX_pipeline is 1
RX_pipeline is 1
NEW_RANK_MODE is 0
close_loop_mode is 1
===================================
===================================
RX_path RG value
===================================
RX_UI_P0[0] is 15
RX_UI_P0[1] is 15
RX_UI_P0[2] is 15
RX_UI_P0[3] is 15
RX_UI_P1[0] is 19
RX_UI_P1[1] is 19
RX_UI_P1[2] is 19
RX_UI_P1[3] is 19
RX_PI[0] is 31
RX_PI[1] is 31
RX_PI[2] is 31
RX_PI[3] is 31
DQSINCTL is 3
DATLAT_DSEL is 11
DATLAT is 12
DATLAT_DSEL_PHY is 12
DLE_EXTEND is 1
RX_IN_GATE_EN_HEAD is 0
RX_IN_GATE_EN_TAIL is 0
RX_IN_BUFF_EN_HEAD is 2
RX_IN_BUFF_EN_TAIL is 0
RX_IN_GATE_EN_PRE_OFFSET is 2
RANKINCTL_ROOT1 is 1
RANKINCTL is 1
RANKINCTL_STB is 2
RANKINCTL_RXDLY is 0
SHU_GW_THRD_POS is 42
SHU_GW_THRD_NEG is 0
RDSEL_TRACK_EN is 0
RDSEL_HWSAVE_MSK is 1
DMDATLAT_i is 12
RODTEN is 0
RODT is 1541211177
RODTE is 1
RODTE2 is 1
ODTEN_MCK_P0[4] is 0
ODTEN_MCK_P1[4] is 0
ODTEN_UI_P0[4] is 0
ODTEN_UI_P1[4] is 0
RX_RANK_DQS_LAT is 0
RX_RANK_DQ_LAT is 1
RANKINCTL_PHY is 5
RANK_SEL_LAT_CA is 0
RANK_SEL_LAT_B0 is 0
RANK_SEL_LAT_B1 is 0
RANK_SEL_STB_EN is 0
RANK_SEL_RXDLY_TRACK is 0
RANK_SEL_STB_TRACK is 1
RANK_SEL_STB_PHASE_EN is 1
RANK_SEL_PHSINCTL is 2
RANK_SEL_STB_UI_MINUS is 2
RANK_SEL_STB_UI_PLUS is 0
RANK_SEL_MCK_P0 is 0
RANK_SEL_UI_P0 is 0
RANK_SEL_MCK_P1 is 1
RANK_SEL_UI_P1 is 0
R0DQSIENLLMTEN is 1
R0DQSIENLLMT is 96
R0DQSIENHLMTEN is 1
R0DQSIENHLMT is 63
R1DQSIENLLMTEN is 1
R1DQSIENLLMT is 96
R1DQSIENHLMTEN is 1
R1DQSIENHLMT is 63
DQSIEN_FIFO_DEPTH_HALF is 1
===================================
[ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:===================================
PCDDR4 DRAM CONFIGURATION
===================================
CWL = 0x7
RTT_NORM = 0x6
CL = 0xb
AL = 0x0
BL = 0x0
RBT = 0x0
WR = 0x8
===================================
[WriteLatency GET] MR_CWL:[WriteLatency GET] MR_CWL:=====================================
print TX_path_config
=====================================
data_ratio is 3200
dq_p2s_ratio is 8
cs2WL_start is 1
byte_num is 2
rank_num is 2
CKR is 1
DBI_WR is 0
dly_1T_by_FDIV2 is 0
WL[0] is 20
WL[1] is 20
TDQSS[0][0] is 156
TDQSS[0][1] is 156
TDQSS[1][0] is 156
TDQSS[1][1] is 156
TDQS2DQ[0][0] is 0
TDQS2DQ[0][1] is 0
TDQS2DQ[1][0] is 0
TDQS2DQ[1][1] is 0
ca_p2s_ratio is 8
ca_default_dly is 1
ca_default_pi is 0
ca_ser_latency is 7
dqs_ser_laterncy is 7
dqs_default_dly is 5
dqs_oe_default_dly is 2
dq_ser_laterncy is 7
MCK_unit is 2496
dq_ui_unit is 312
ca_unit is 312
ca_MCKIO_unit is 312
ca_frate is 0
TX_ECC is 0
TWPRE is 4
OE_pre_margin is 400
OE_pst_margin is 500
OE_downgrade is 1
aphy_slice_dly is 11
aphy_dtc_dly is 100
aphy_tx_dly is 16
DDRPHY_CLK_EN_COMB_TX_OPT is 1
NEW_RANK_MODE is 0
close_loop_mode is 1
TXP_WORKAROUND_OPT is 0
ui2pi_ratio is 32
XRTW2W_PI_mute_time is 7
fake_mode is 0
===========================================
TX_DQ_UI_OE_pre is 2
TX_DQS_UI_OE_pre is 1
data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3
data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3
data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3
data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3
===========================================
print TX_path_attribution
===========================================
TX_DQ_MCK_OE[0][0] is 2
TX_DQ_MCK_OE[0][1] is 2
TX_DQ_MCK_OE[1][0] is 2
TX_DQ_MCK_OE[1][1] is 2
TX_DQ_UI_OE[0][0] is 6
TX_DQ_UI_OE[0][1] is 6
TX_DQ_UI_OE[1][0] is 6
TX_DQ_UI_OE[1][1] is 6
TX_DQ_MCK[0][0] is 3
TX_DQ_MCK[0][1] is 3
TX_DQ_MCK[1][0] is 3
TX_DQ_MCK[1][1] is 3
TX_DQ_UI[0][0] is 2
TX_DQ_UI[0][1] is 2
TX_DQ_UI[1][0] is 2
TX_DQ_UI[1][1] is 2
TX_DQ_PI[0][0] is 0
TX_DQ_PI[0][1] is 0
TX_DQ_PI[1][0] is 0
TX_DQ_PI[1][1] is 0
TX_DQ_UIPI_all[0][0] is 0
TX_DQ_UIPI_all[0][1] is 0
TX_DQ_UIPI_all[1][0] is 0
TX_DQ_UIPI_all[1][1] is 0
TX_DQ_dlyline[0][0] is 0
TX_DQ_dlyline[0][1] is 0
TX_DQ_dlyline[1][0] is 0
TX_DQ_dlyline[1][1] is 0
TX_DQS_MCK_OE[0][0] is 2
TX_DQS_MCK_OE[0][1] is 2
TX_DQS_MCK_OE[1][0] is 2
TX_DQS_MCK_OE[1][1] is 2
TX_DQS_UI_OE[0][0] is 6
TX_DQS_UI_OE[0][1] is 6
TX_DQS_UI_OE[1][0] is 6
TX_DQS_UI_OE[1][1] is 6
TX_DQS_MCK[0][0] is 3
TX_DQS_MCK[0][1] is 3
TX_DQS_MCK[1][0] is 3
TX_DQS_MCK[1][1] is 3
TX_DQS_UI[0][0] is 1
TX_DQS_UI[0][1] is 1
TX_DQS_UI[1][0] is 1
TX_DQS_UI[1][1] is 1
DDRPHY_CLK_EN_COMB_TX_OPT is 1
TX_DQS_PI[0][0] is 16
TX_DQS_PI[0][1] is 16
TX_DQS_PI[1][0] is 16
TX_DQS_PI[1][1] is 16
DDRPHY_CLK_EN_COMB_TX_PICG_CNT is 2
DDRPHY_CLK_EN_COMB_TX_DQS_SEL_P0 is 3
DDRPHY_CLK_EN_COMB_TX_DQS_SEL_P1 is 4
DDRPHY_CLK_EN_COMB_TX_DQ_RK0_SEL_P0 is 3
DDRPHY_CLK_EN_COMB_TX_DQ_RK0_SEL_P1 is 4
DDRPHY_CLK_EN_COMB_TX_DQ_RK1_SEL_P0 is 3
DDRPHY_CLK_EN_COMB_TX_DQ_RK1_SEL_P1 is 4
DPHY_TX_DCM_EXTCNT is 0
TX_PI_UPD_MODE is 1
TX_PI_UPDCTL_B0 is 0
TX_PI_UPDCTL_B1 is 0
TX_RANKINCTL_ROOT is 0
TX_RANKINCTL is 1
TX_RANKINCTL_TXDLY is 2
DDRPHY_CLK_DYN_GATING_SEL is 5
DDRPHY_CLK_EN_OPT is 1
ARPI_CMD is 0
TDMY is 9
TXOEN_AUTOSET_DQ_OFFSET is 3
TXOEN_AUTOSET_DQS_OFFSET is 3
TXOEN_AUTOSET_EN is 1
TXPICG_AUTOSET_OPT is 0
TXPICG_AUTOSET_EN is 1
TXPICG_DQ_MCK_OFFSET_LAG is 0
TXPICG_DQS_MCK_OFFSET_LAG is 0
TXPICG_DQ_UI_OFFSET_LEAD is 0
TXPICG_DQ_UI_OFFSET_LAG is 1
TXPICG_DQS_UI_OFFSET_LEAD is 1
TXPICG_DQS_UI_OFFSET_LAG is 0
===========================================
set APHY_PI_CKCGH_CNT is 4 when not fake_mode, cur data_rate is 3200
[DIG_SHUF_CONFIG] MISC >>>>>, group_id=0
[DIG_SHUF_CONFIG] MISC <<<<<<, group_id=0
[DIG_SHUF_CONFIG] DBI >>>>>>, group_id=0
[DIG_SHUF_CONFIG] DBI <<<<<<, group_id=0
dramc_dram_ratio: 4
DDR4_DivMode: 1
freq_index: 1600
match AC timing 1
[DDR4_ac_timing_setting]start
[PC4 WR preamble settings]>>>>>>>> group_id = 0.
[PC4 WR preamble settings]<<<<<<<< group_id = 0.
clk_dramc_ref_sel FREQ=16
fmem_ck_bfe_dcm_ch0 FREQ=253
fmem_ck_aft_dcm_ch0 FREQ=253
SetClkFreeRun enter => DRAM clock free run mode = ON.
[DDR4] Pull Down reset.
[DDR4] cke fix low 10ns at least.
[DDR4] Delay 200 us.
[DDR4] Pull Up reset.
[DDR4] Delay 500 us.
[DDR4] DRAM initilization RK:0 Enter >>>>>>>>
[DDR4] Delay TXPR TRFC+10ns - 350ns(8Gb density)+10ns
[DDR4_MRS] RK:0-MA:2-OP:0x[DDR4_MRS] RK:0-MA:3-OP:0x[DDR4_MRS] RK:0-MA:1-OP:0x[DDR4_MRS] RK:0-MA:4-OP:0x[DDR4_MRS] RK:0-MA:5-OP:0x[DDR4] DQ Vref calibration>>>>>>>
[DDR4] DQ Vref Enable DQ vref calibration.
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] wait tVREFDQE-150ns
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] DQ Vref modify range and value
[DDR4] DQ Vref Exit DQ vref calibration.
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] wait tVREFDQx-150ns
[DDR4] DQ Vref calibration<<<<<<<
[DDR4_MRS] RK:0-MA:0-OP:0x[DDR4_ZQ] RK:0 Enter >>>>>>>>
[DDR4_ZQ] RK:0 Exit <<<<<<<<
[DDR4] Delay ZQinit - 718ns for 1333 at least max(512Mck,640ns)
[DDR4] DRAM initilization RK:0 Exit <<<<<<<
[DDR4] Enable refresh.....All bank refresh only
SetClkFreeRun enter => DRAM clock free run mode = OFF.
[DIG_HW_NONSHUF_ZQCAL_SWITCH],Configuration Enter
[DIG_HW_NONSHUF_DQSG_SWITCH],Configuration Enter
SET_CKE_2_RANK_INDEPENDENT_RUN_TIME: ON
[MiockJmeterHQA]
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
[DramcMiockJmeter] u1RxGatingPI = 0
0 : 2282, 2282
1 : 2271, 2271
2 : 2271, 2271
3 : 2272, 2272
4 : 2271, 2271
5 : 2271, 2271
6 : 2276, 2276
7 : 2272, 2272
8 : 2272, 2272
9 : 2272, 2272
10 : 2272, 2272
11 : 2271, 2271
12 : 2271, 2271
13 : 2272, 2272
14 : 2271, 2271
15 : 2271, 2271
16 : 2272, 2272
17 : 2271, 2271
18 : 2271, 2271
19 : 2272, 2272
20 : 2271, 2271
21 : 2271, 2271
22 : 2271, 2271
23 : 2272, 2272
24 : 2271, 2271
25 : 2272, 2272
26 : 2271, 2271
27 : 2271, 2271
28 : 2272, 2272
29 : 2276, 2276
30 : 2272, 2272
31 : 2271, 2271
32 : 2272, 2272
33 : 2271, 2271
34 : 2272, 2272
35 : 2271, 2271
36 : 2271, 2271
37 : 2272, 1832
38 : 2271, 0
39 : 2272, 0
40 : 2271, 0
41 : 2272, 0
42 : 2267, 0
43 : 2267, 0
44 : 2271, 0
45 : 2272, 0
46 : 2271, 0
47 : 2271, 0
48 : 2267, 0
49 : 2271, 0
50 : 2271, 0
51 : 2272, 0
52 : 2271, 0
53 : 2271, 0
54 : 2271, 0
55 : 2271, 0
56 : 2272, 0
57 : 2271, 0
58 : 2271, 0
59 : 2276, 0
60 : 2276, 0
61 : 2271, 0
62 : 2272, 0
63 : 2276, 0
64 : 2271, 0
65 : 2272, 0
66 : 2276, 0
67 : 2272, 0
68 : 2272, 0
69 : 2271, 0
70 : 2271, 0
71 : 2272, 0
72 : 2276, 0
73 : 2271, 0
74 : 2271, 0
75 : 2272, 0
76 : 2271, 0
77 : 2271, 0
78 : 2271, 0
79 : 2272, 0
80 : 2271, 0
81 : 2271, 0
82 : 2276, 0
83 : 2271, 0
84 : 2272, 0
85 : 2272, 0
86 : 2271, 0
87 : 2266, 0
88 : 2272, 0
89 : 2271, 1888
90 : 2271, 2267
91 : 2271, 2271
92 : 2271, 2271
93 : 2272, 2272
94 : 2271, 2271
95 : 2272, 2272
96 : 2272, 2272
97 : 2276, 2276
98 : 2271, 2271
99 : 2271, 2271
100 : 2271, 2271
101 : 2271, 2271
102 : 2272, 2272
103 : 2272, 2272
104 : 2276, 2276
105 : 2272, 2272
106 : 2272, 2272
107 : 2276, 2276
108 : 2271, 2271
109 : 2271, 2271
110 : 2271, 2271
111 : 2272, 2272
112 : 2271, 2271
113 : 2271, 2271
114 : 2271, 2271
115 : 2271, 2271
116 : 2272, 2272
117 : 2271, 2271
118 : 2271, 2271
119 : 2271, 2271
120 : 2271, 2271
121 : 2271, 2271
122 : 2276, 2276
123 : 2271, 2271
124 : 2276, 2276
125 : 2271, 2271
126 : 2272, 2272
127 : 2271, 2271
MIOCK jitter meter ch=0
1T = (89-38)*2 = 102 dly cells
Clock freq = 1560 MHz, period = 641 ps, 1 dly cell = 628/100 ps
----->DramcWriteLeveling(PI) begin...
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
Begin: 0, End: 63, Step: 1, Bound: 64
[DDR4_MRS] RK:0-MA:2-OP:0x[DDR4_MRS] RK:0-MA:1-OP:0x[Write Leveling]
delay byte0 byte1 byte2 byte3
0 O1( 1 1
1 O1( 1 1
2 O1( 1 1
3 O1( 1 1
4 O1( 1 1
5 O1( 1 1
6 O1( 1 1
7 O1( 1 1
8 O1( 1 1
9 O1( 1 1
10 O1( 1 1
11 O1( 1 0
12 O1( 1 0
13 O1( 1 0
14 O1( 1 0
15 O1( 1 0
16 O1( 0 0
17 O1( 0 0
18 O1( 0 0
19 O1( 0 0
20 O1( 0 0
21 O1( 0 0
22 O1( 0 0
23 O1( 0 0
24 O1( 0 0
25 O1( 0 0
26 O1( 0 0
27 O1( 0 0
28 O1( 0 0
29 O1( 0 0
30 O1( 0 0
31 O1( 0 0
32 O1( 0 0
33 O1( 0 0
34 O1( 0 0
35 O1( 0 0
36 O1( 0 0
37 O1( 0 0
38 O1( 0 0
39 O1( 0 0
40 O1( 0 0
41 O1( 0 0
42 O1( 0 1
43 O1( 1 1
44 O1( 1 1
45 O1( 1 1
46 O1( 1 1
47 O1( 1 1
48 O1( 1 1
49 O1( 1 1
Early breakpass bytecount = 0xff (0xff: all bytes pass)
[DDR4_MRS] RK:0-MA:1-OP:0x[DDR4_MRS] RK:0-MA:2-OP:0xWrite leveling (Byte 0): 43 => 43
Write leveling (Byte 1): 42 => 42
DramcWriteLeveling(PI) end<-----
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
[Gating] SW mode calibration
[get_gating_start_pos] calculated gating ui = 15
12 0 | B1->B0 | 1111 1212 | 1 1 | (0 0) (0 0)
12 4 | B1->B0 | 1111 1212 | 1 1 | (0 0) (0 0)
12 8 | B1->B0 | 1111 1212 | 1 1 | (0 0) (0 0)
12 12 | B1->B0 | 1111 1111 | 1 1 | (0 1) (0 1)
12 16 | B1->B0 | 1111 1111 | 1 1 | (0 1) (0 1)
12 20 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1)
12 24 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1)
12 28 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1)
13 0 | B1->B0 | 1111 1212 | 1 1 | (1 1) (1 1)
13 4 | B1->B0 | 1111 1212 | 1 1 | (1 1) (1 1)
13 8 | B1->B0 | 1111 1212 | 1 1 | (1 1) (1 1)
13 12 | B1->B0 | 2323 2222 | 0 0 | (0 0) (0 0)
13 16 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
13 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
13 24 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
13 28 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
14 0 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
14 4 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
14 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
14 12 | B1->B0 | 2323 2323 | 0 0 | (0 1) (0 0)
14 16 | B1->B0 | 2222 2323 | 0 0 | (1 1) (0 1)
14 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
14 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
14 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
15 0 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1)
15 4 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1)
15 8 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1)
15 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
15 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
15 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
15 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
15 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
16 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
16 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (0 0)
16 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
16 12 | B1->B0 | 2323 2323 | 0 0 | (0 1) (0 0)
16 16 | B1->B0 | 2323 2323 | 0 0 | (0 1) (0 1)
16 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
16 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
16 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 8 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
17 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
18 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
18 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
18 8 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1)
18 12 | B1->B0 | 2323 2323 | 0 0 | (1 0) (1 0)
18 16 | B1->B0 | 2323 2323 | 0 0 | (1 0) (1 0)
18 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
18 24 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
18 28 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
19 0 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
19 4 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
19 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
best dqsien dly found for B0: (18, 14)
19 12 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
19 16 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
19 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0)
best dqsien dly found for B1: (18, 14)
best DQS0 dly(UI, PI) = (18, 14)
best DQS1 dly(UI, PI) = (18, 14)
[Gating] SW calibration Done
[DDR4_MRS] RK:0-MA:3-OP:0x===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
Start DQ dly to find pass range UseTestEngine =0
UseTestEngine: 0
RX Vref Scan: 0
RX Vref 0 -> 0, step: 1
RX Delay -48 -> 63, step: 4
-48, [0] xxxxxxxx xxxxxxxx [MSB]
-44, [0] xxxxxxxx xxxxxxxx [MSB]
-40, [0] xxxxxxxx xxxxxxxx [MSB]
-36, [0] xxxxxxxx xxxxxxxx [MSB]
-32, [0] xxxxxxxx xxxxxxxx [MSB]
-28, [0] xxxxxxxx xxxxxxxx [MSB]
-24, [0] xxxxxxxx xxxxxxxx [MSB]
-20, [0] xxxxxxxx xxxxxxxx [MSB]
-16, [0] xxxxxxxx xxxxxxxx [MSB]
-12, [0] xxxxxxxx xxxxxxxx [MSB]
-8, [0] xxxxxxxx xxxxxxxx [MSB]
-4, [0] xxxxxxox xxxxxxxx [MSB]
0, [0] xxoxoxox xxoxoxxx [MSB]
4, [0] oxoooxoo oooooxoo [MSB]
8, [0] oooooooo oooooooo [MSB]
12, [0] oooooooo oooooooo [MSB]
16, [0] oooooooo oooooooo [MSB]
20, [0] oooooooo oooooooo [MSB]
24, [0] oooooooo oooooooo [MSB]
28, [0] oooooooo oooooooo [MSB]
32, [0] oooooooo oooooooo [MSB]
36, [0] ooxoooxo oooooooo [MSB]
40, [0] ooxoxoxo ooxoxoxo [MSB]
44, [0] xoxxxxxx xxxxxxxx [MSB]
48, [0] xxxxxxxx xxxxxxxx [MSB]
RX Vref B0= 0, Window Sum 312, worse bit 2, min window 36
iDelay=48, Bit 0, Center 23 (4 ~ 43) 40
iDelay=48, Bit 1, Center 27 (8 ~ 47) 40
iDelay=48, Bit 2, Center 17 (0 ~ 35) 36
iDelay=48, Bit 3, Center 23 (4 ~ 43) 40
iDelay=48, Bit 4, Center 19 (0 ~ 39) 40
iDelay=48, Bit 5, Center 25 (8 ~ 43) 36
iDelay=48, Bit 6, Center 15 (-4 ~ 35) 40
iDelay=48, Bit 7, Center 23 (4 ~ 43) 40
RX Vref B1= 0, Window Sum 312, worse bit 13, min window 36
iDelay=48, Bit 8, Center 23 (4 ~ 43) 40
iDelay=48, Bit 9, Center 23 (4 ~ 43) 40
iDelay=48, Bit 10, Center 19 (0 ~ 39) 40
iDelay=48, Bit 11, Center 23 (4 ~ 43) 40
iDelay=48, Bit 12, Center 19 (0 ~ 39) 40
iDelay=48, Bit 13, Center 25 (8 ~ 43) 36
iDelay=48, Bit 14, Center 21 (4 ~ 39) 36
iDelay=48, Bit 15, Center 23 (4 ~ 43) 40
[DDR4_MRS] RK:0-MA:3-OP:0x===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
DQS Delay:
DQS0 = 0, DQS1 = 0
DQM Delay:
DQM0 = 21, DQM1 = 22
DQ Delay:
DQ0 =23, DQ1 =27, DQ2 =17, DQ3 =23
DQ4 =19, DQ5 =25, DQ6 =15, DQ7 =23
DQ8 =23, DQ9 =23, DQ10 =19, DQ11 =23
DQ12 =19, DQ13 =25, DQ14 =21, DQ15 =23
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
[TxWindowPerbitCal] caltype:2 Autok:0
TX Vref Scan disable
810 |3 0 42|[0] xxxxxxox xxxxxxxx [MSB]
812 |3 0 44|[0] oxoxxxox xxxxxxxx [MSB]
814 |3 0 46|[0] oxoxxxox xxxxxxxx [MSB]
816 |3 0 48|[0] oxoxxxox xxoxxxox [MSB]
818 |3 0 50|[0] oooooooo oxoooooo [MSB]
832 |3 2 0|[0] ooooooxo ooxooooo [MSB]
834 |3 2 2|[0] xoxoxoxo xoxoxooo [MSB]
836 |3 2 4|[0] xoxoxoxo xxxxxoxx [MSB]
838 |3 2 6|[0] xoxxxxxo xxxxxxxx [MSB]
840 |3 2 8|[0] xxxxxxxx xxxxxxxx [MSB]
TX Bit0 (812~832) 22 822, Bit8 (818~832) 16 825,
TX Bit1 (818~838) 22 828, Bit9 (820~834) 16 827,
TX Bit2 (812~832) 22 822, Bit10 (816~830) 16 823,
TX Bit3 (818~836) 20 827, Bit11 (818~834) 18 826,
TX Bit4 (818~832) 16 825, Bit12 (818~832) 16 825,
TX Bit5 (818~836) 20 827, Bit13 (818~836) 20 827,
TX Bit6 (810~830) 22 820, Bit14 (816~834) 20 825,
TX Bit7 (818~838) 22 828, Bit15 (818~834) 18 826,
== TX Byte 0 ==
Update DQ dly =824 (3 ,0, 56) DQ OEN =(2 ,5)
Update DQM dly =824 (3 ,0, 56) DQM OEN =(2 ,5)
== TX Byte 1 ==
Update DQ dly =825 (3 ,0, 57) DQ OEN =(2 ,5)
Update DQM dly =825 (3 ,0, 57) DQM OEN =(2 ,5)
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
[TxWindowPerbitCal] caltype:0 Autok:0
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 3
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 5
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 7
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 9
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 11
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 13
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 15
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 17
TX Vref=3, minBit 8, minWin=13, winSum=263
TX Vref=5, minBit 9, minWin=14, winSum=275
TX Vref=7, minBit 10, minWin=14, winSum=281
TX Vref=9, minBit 9, minWin=16, winSum=295
TX Vref=11, minBit 10, minWin=15, winSum=299
TX Vref=13, minBit 10, minWin=15, winSum=305
TX Vref=15, minBit 9, minWin=17, winSum=317
TX Vref=17, minBit 4, minWin=18, winSum=323
[TxChooseVref] Worse bit 4, Min win 18, Win sum 323, Final Vref 17
[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 17
Final TX Range 1 Vref 17
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
[TxWindowPerbitCal] caltype:0 Autok:0
TX Vref Scan disable
810 |3 0 42|[0] xxxxxxxx xxxxxxxx [MSB]
811 |3 0 43|[0] xxxxxxox xxxxxxxx [MSB]
812 |3 0 44|[0] xxxxxxox xxxxxxxx [MSB]
813 |3 0 45|[0] xxxxxxox xxxxxxxx [MSB]
814 |3 0 46|[0] oxoxxxox xxoxxxxx [MSB]
815 |3 0 47|[0] oxoxxxox xxoxoxox [MSB]
816 |3 0 48|[0] oxoxxxox xxoxoooo [MSB]
817 |3 0 49|[0] oooooooo oxoooooo [MSB]
833 |3 2 1|[0] ooooooxo oooooooo [MSB]
834 |3 2 2|[0] xoxoooxo ooxooooo [MSB]
835 |3 2 3|[0] xoxoxoxo xoxoxooo [MSB]
836 |3 2 4|[0] xoxoxoxo xoxxxoxx [MSB]
837 |3 2 5|[0] xoxoxoxo xxxxxxxx [MSB]
838 |3 2 6|[0] xoxxxoxo xxxxxxxx [MSB]
839 |3 2 7|[0] xoxxxxxo xxxxxxxx [MSB]
840 |3 2 8|[0] xxxxxxxx xxxxxxxx [MSB]
TX Bit0 (814~833) 20 823, Bit8 (817~834) 18 825,
TX Bit1 (817~839) 23 828, Bit9 (818~836) 19 827,
TX Bit2 (814~833) 20 823, Bit10 (814~833) 20 823,
TX Bit3 (817~837) 21 827, Bit11 (817~835) 19 826,
TX Bit4 (817~834) 18 825, Bit12 (815~834) 20 824,
TX Bit5 (817~838) 22 827, Bit13 (816~836) 21 826,
TX Bit6 (811~832) 22 821, Bit14 (815~835) 21 825,
TX Bit7 (817~839) 23 828, Bit15 (816~835) 20 825,
[TX_PER_BIT_DELAY_CELL] DelayCellTimex100 =628/100 ps
== TX Byte 0 ==
u2DelayCellOfst[0]=3 cells (2 PI)
u2DelayCellOfst[1]=10 cells (7 PI)
u2DelayCellOfst[2]=3 cells (2 PI)
u2DelayCellOfst[3]=9 cells (6 PI)
u2DelayCellOfst[4]=6 cells (4 PI)
u2DelayCellOfst[5]=9 cells (6 PI)
u2DelayCellOfst[6]=0 cells (0 PI)
u2DelayCellOfst[7]=10 cells (7 PI)
Update DQ dly =821 (3 ,0, 53) DQ OEN =(2 ,5)
Update DQM dly =824 (3 ,0, 56) DQM OEN =(2 ,5)
== TX Byte 1 ==
u2DelayCellOfst[8]=3 cells (2 PI)
u2DelayCellOfst[9]=6 cells (4 PI)
u2DelayCellOfst[10]=0 cells (0 PI)
u2DelayCellOfst[11]=4 cells (3 PI)
u2DelayCellOfst[12]=1 cells (1 PI)
u2DelayCellOfst[13]=4 cells (3 PI)
u2DelayCellOfst[14]=3 cells (2 PI)
u2DelayCellOfst[15]=3 cells (2 PI)
Update DQ dly =823 (3 ,0, 55) DQ OEN =(2 ,5)
Update DQM dly =825 (3 ,0, 57) DQM OEN =(2 ,5)
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
DATLAT Default: 0xc
0, 0x1, 0x2, 0x3, 0x4, 0x5, 0x6, 0x7, 0x8, 0x9, 0x10, 0x11, 0x12, 0x13, 0xbest_step = 11
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
Start DQ dly to find pass range UseTestEngine =1
UseTestEngine: 1
RX Vref Scan: 1
Set Vref Range= 9 -> 21
RX Vref 9 -> 21, step: 1
RX Delay -14 -> 63, step: 2
Set Vref, RX VrefLevel [Byte0]: 9 [Byte1]: 9
RX Vref B0= 9, Window Sum 226, worse bit 6, min window 26
RX Vref B1= 9, Window Sum 208, worse bit 10, min window 24
Set Vref, RX VrefLevel [Byte0]: 10 [Byte1]: 10
RX Vref B0= 10, Window Sum 236, worse bit 4, min window 28
RX Vref B1= 10, Window Sum 222, worse bit 10, min window 26
Set Vref, RX VrefLevel [Byte0]: 11 [Byte1]: 11
RX Vref B0= 11, Window Sum 250, worse bit 0, min window 30
RX Vref B1= 11, Window Sum 236, worse bit 10, min window 26
Set Vref, RX VrefLevel [Byte0]: 12 [Byte1]: 12
RX Vref B0= 12, Window Sum 260, worse bit 0, min window 32
RX Vref B1= 12, Window Sum 240, worse bit 10, min window 28
Set Vref, RX VrefLevel [Byte0]: 13 [Byte1]: 13
RX Vref B0= 13, Window Sum 264, worse bit 0, min window 32
RX Vref B1= 13, Window Sum 246, worse bit 10, min window 28
Set Vref, RX VrefLevel [Byte0]: 14 [Byte1]: 14
RX Vref B0= 14, Window Sum 278, worse bit 1, min window 34
RX Vref B1= 14, Window Sum 260, worse bit 10, min window 30
Set Vref, RX VrefLevel [Byte0]: 15 [Byte1]: 15
RX Vref B0= 15, Window Sum 286, worse bit 4, min window 34
RX Vref B1= 15, Window Sum 266, worse bit 9, min window 32
Set Vref, RX VrefLevel [Byte0]: 16 [Byte1]: 16
RX Vref B1= 16, Window Sum 276, worse bit 10, min window 32
Set Vref, RX VrefLevel [Byte0]: 17 [Byte1]: 17
RX Vref B0= 17, Window Sum 294, worse bit 0, min window 36
RX Vref B1= 17, Window Sum 280, worse bit 8, min window 34
Set Vref, RX VrefLevel [Byte0]: 18 [Byte1]: 18
RX Vref B1= 18, Window Sum 290, worse bit 8, min window 34
Set Vref, RX VrefLevel [Byte0]: 19 [Byte1]: 19
Set Vref, RX VrefLevel [Byte0]: 20 [Byte1]: 20
Final RX Vref Byte 0 = 17 to rank0 to rank1
Final RX Vref Byte 1 = 18 to rank0 to rank1
===============================================================================
Dram Type= 4, Freq= 1600, CH_0, rank 0
fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1
===============================================================================
DQS Delay:
DQS0 = 0, DQS1 = 0
DQM Delay:
DQM0 = 22, DQM1 = 24
DQ Delay:
DQ0 =23, DQ1 =27, DQ2 =19, DQ3 =25
DQ4 =21, DQ5 =26, DQ6 =16, DQ7 =24
DQ8 =24, DQ9 =26, DQ10 =22, DQ11 =26
DQ12 =22, DQ13 =26, DQ14 =22, DQ15 =25
[DualRankRxdatlatCal] RK0: 11, RK1: 0, Final_Datlat 11
[Calibration Summary] Freqency 1600
CH 0, Rank 0
SW Impedance : PASS
DUTY Scan : NO K
ZQ Calibration : PASS
Jitter Meter : NO K
CBT Training : NO K
Write leveling : PASS
RX DQS gating : PASS
RX DQ/DQS(RDDQC) : PASS
TX DQ/DQS : PASS
RX DATLAT : PASS
RX DQ/DQS(Engine): PASS
TX OE : NO K
All Pass.
TX_TRACKING: OFF
[AUTO] write start address pass, BASE_ADDR : 0x0, OFFSET : 0x3
[AUTO] Detect DramSize: 0x8000000
[AUTO] BASE_ADDR : 0x8000000, OFFSET : 0x3
[AUTO] BASE_ADDR : 0x0, OFFSET : 0x3
[AUTO] Detect DramSize: 0x10000000
[AUTO] BASE_ADDR : 0x10000000, OFFSET : 0x3
[AUTO] BASE_ADDR : 0x0, OFFSET : 0x3
[AUTO] Detect DramSize: 0x20000000
[AUTO] BASE_ADDR : 0x20000000, OFFSET : 0x3
[AUTO] BASE_ADDR : 0x0, OFFSET : 0x3
[AUTO] TA2 read check fail, u4err_value = 65535, 3
[AUTO] Detect full size
u4DramSize 0x20000000
NOTICE: EMI: Detected DRAM size: 512MB
[MEM_TEST] 02: After DFS, before run time config
[MEM_TEST] Rank 0 OK.(uiFixedAddr 0x40000000, Pass count = 16384, Fail count = 0)
[TA2_TEST]
=== TA2 HW
=== OFFSET:0x200
TA2 PAT: 3
TA2 Trigger Write
HW channel(0) Rank(0), TA2 pass, pass_cnt:1, err_cnt:0
[DramcRunTimeConfig]: ON
PHYPLL
DPM_CONTROL_AFTERK: ON
PER_BANK_REFRESH: OFF
REFRESH_OVERHEAD_REDUCTION: ON
CMD_PICG_NEW_MODE: OFF
TX_TRACKING: OFF
RDSEL_TRACKING: OFF
DQS Precalculation for DVFS: OFF
RX_TRACKING: OFF
DDR_HW_GATING DBG: ON
DDR_ZQCS_ENABLE: ON
RX_PICG_NEW_MODE: ON
TX_PICG_NEW_MODE: ON
ENABLE_RX_DCM_DPHY: ON
LOWPOWER_GOLDEN_SETTINGS(DCM): ON
DUMMY_READ_FOR_TRACKING: OFF
!!! SPM_CONTROL_AFTERK: OFF
!!! SPM could not control APHY
IMPEDANCE_TRACKING: OFF
HW_SAVE_FOR_SR: OFF
CLK_FREE_FUN_FOR_DRAMC_PSEL: OFF
PA_IMPROVEMENT_FOR_DRAMC_ACTIVE_POWER: OFF
Read ODT Tracking: OFF
Refresh Rate DeBounce: OFF
DFS_NO_QUEUE_FLUSH: OFF
DFS_NO_QUEUE_FLUSH_LATENCY_CNT: OFF
ENABLE_DFS_RUNTIME_MRW: OFF
DDR_RESERVE_NEW_MODE: ON
=========================
[MEM_TEST] 03: After run time config
[MEM_TEST] Rank 0 OK.(uiFixedAddr 0x40000000, Pass count = 16384, Fail count = 0)
[TA2_TEST]
=== TA2 HW
=== OFFSET:0x200
TA2 Trigger Write
HW channel(0) Rank(0), TA2 pass, pass_cnt:2, err_cnt:0
Init_DRAM:2480: init PCDDR4 dram End
EMI: complex real chip dram calibration
Verify pattern 1 (0x00~0xff)...
EMI: mem8_base[0] = pattern8 = 0x0
Verify pattern 2 (0x00~0xffff)...
EMI: mem16_base[0] = pattern16 = 0x0
Verify pattern 3 (0x00~0xffffffff)...
EMI: mem32_base[0] = pattern32 = 0x0
NOTICE: EMI: complex R/W mem test passed
drm_dram_reserved: MTK_DRM_MODE(22000000)
NOTICE: SPI_NAND parses attributes from parameter page.
NOTICE: SPI_NAND Detected ID 0x0
NOTICE: Page size 2048, Block size 131072, size 134217728
NOTICE: Initializing NMBM ...
NOTICE: Signature found at block 1023 [0x07fe0000]
NOTICE: First info table with writecount 0 found in block 960
NOTICE: Second info table with writecount 0 found in block 963
NOTICE: NMBM has been successfully attached in read-only mode
INFO: BL2: Loading image id 3
INFO: Loading image id=3 at address 0x42000000
INFO: Image id=3 loaded: 0x42000000 - 0x42009061
INFO: BL2: Loading image id 5
INFO: Loading image id=5 at address 0x42000000
INFO: Image id=5 loaded: 0x42000000 - 0x420ae288
NOTICE: BL2: Booting BL31
INFO: Entry point address = 0x43001000
INFO: SPSR = 0x3cd
INFO: Total CPU count: 4
INFO: MCUSYS: Disable 512KB L2C shared SRAM
INFO: check_ver = 0
INFO: Secondary bootloader is AArch64
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: Maximum SPI INTID supported: 671
INFO: SPMC: Changed to SPMC mode
NOTICE: BL31: v2.6(release):2598dbc2a6-dirty
NOTICE: BL31: Built : 13:34:54, Mar 12 2022
INFO: [MPU](Region0)sa:0x0300, ea:0x0302
INFO: [MPU](Region0)apc0:0x80b6db69, apc1:0x00b6db6d
INFO: [MPU](Region1)sa:0x0000, ea:0x0000
INFO: [MPU](Region1)apc0:0x00000000, apc1:0x00000000
INFO: [MPU](Region2)sa:0x0000, ea:0x0000
INFO: [MPU](Region2)apc0:0x00000000, apc1:0x00000000
INFO: [MPU](Region3)sa:0x0000, ea:0x0000
INFO: [MPU](Region3)apc0:0x00000000, apc1:0x00000000
INFO: [DEVAPC] devapc_init done
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x41e00000
INFO: SPSR = 0x3c9
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net: eth0: ethernet@15100000
detect button reset released!
Reading from 0x0 to 0x5f7fdd8c, size 0x4 ... OK
Reading from 0x0 to 0x5f7fdd8c, size 0x4 ... OK
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
Booting System 1
ubi0: attaching mtd10
ubi0: scanning is finished
ubi0: attached mtd10 (name "ubi1", size 30 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 662404348
ubi0: available PEBs: 64, total reserved PEBs: 176, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK
## Loading kernel from FIT Image at 46000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM64 OpenWrt Linux-5.4.150
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x460000e8
Data Size: 3160816 Bytes = 3 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x44080000
Entry Point: 0x44080000
Hash algo: crc32
Hash value: bd0e32dd
Hash algo: sha1
Hash value: 994c9b27486ab63b8f302c3fb83dd30b09d54027
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config@1' configuration
Trying 'fdt@1' fdt subimage
Description: ARM64 OpenWrt mt7986-RB06 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x46303d14
Data Size: 20485 Bytes = 20 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 4c66671d
Hash algo: sha1
Hash value: 65a8b044ad027aa577386dd21f4a51ac0a9e6287
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x46303d14
Uncompressing Kernel Image
Loading Device Tree to 000000005f7f1000, end 000000005f7f9004 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.4.150 (jenkins@a92f094d1440) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 unknown)) #0 SMP Fri Aug 12 08:32:47 2022
[ 0.000000] Machine model: MediaTek MT7986a RFB
[ 0.000000] On node 0 totalpages: 130064
[ 0.000000] DMA32 zone: 2048 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 130064 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 20 pages/cpu s43608 r8192 d30120 u81920
[ 0.000000] pcpu-alloc: s43608 r8192 d30120 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 128016
[ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 491052K/520256K available (6398K kernel code, 490K rwdata, 1892K rodata, 448K init, 283K bss, 29204K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] random: get_random_bytes called from start_kernel+0x2d4/0x418 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000002] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000102] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000)
[ 0.000108] pid_max: default: 32768 minimum: 301
[ 0.000158] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.000163] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.000810] ASID allocator initialised with 65536 entries
[ 0.000845] rcu: Hierarchical SRCU implementation.
[ 0.001053] smp: Bringing up secondary CPUs ...
[ 0.001263] Detected VIPT I-cache on CPU1
[ 0.001282] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.001301] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.001520] Detected VIPT I-cache on CPU2
[ 0.001528] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.001537] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.001727] Detected VIPT I-cache on CPU3
[ 0.001735] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.001742] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.001768] smp: Brought up 1 node, 4 CPUs
[ 0.001778] SMP: Total of 4 processors activated.
[ 0.001781] CPU features: detected: 32-bit EL0 Support
[ 0.001784] CPU features: detected: CRC32 instructions
[ 0.001871] CPU: All CPU(s) started at EL2
[ 0.001881] alternatives: patching kernel code
[ 0.003577] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.003593] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.003706] pinctrl core: initialized pinctrl subsystem
[ 0.004178] NET: Registered protocol family 16
[ 0.004344] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.005193] pstore: Registered ramoops as persistent store backend
[ 0.005200] ramoops: using 0x100000@0x42f00000, ecc: 0
[ 0.012358] cryptd: max_cpu_qlen set to 1000
[ 0.013391] SCSI subsystem initialized
[ 0.013485] libata version 3.00 loaded.
[ 0.013963] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.014443] rbus 18000000.wbsys: PCI host bridge to bus 0000:00
[ 0.014451] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff]
[ 0.014457] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.014461] pci_bus 0000:00: scanning bus
[ 0.014476] pci 0000:00:00.0: [14c3:7986] type 00 class 0x000280
[ 0.014488] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit]
[ 0.014493] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f]
[ 0.014497] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f]
[ 0.014501] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f]
[ 0.014505] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f]
[ 0.015152] pci_bus 0000:00: fixups for bus
[ 0.015156] pci_bus 0000:00: bus scan returning with max=00
[ 0.015371] clocksource: Switched to clocksource arch_sys_counter
[ 0.015780] thermal_sys: Registered thermal governor 'fair_share'
[ 0.015782] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.015786] thermal_sys: Registered thermal governor 'step_wise'
[ 0.015789] thermal_sys: Registered thermal governor 'user_space'
[ 0.015792] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.015972] NET: Registered protocol family 2
[ 0.016034] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.016359] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.016366] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.016386] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.016426] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.016477] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.016487] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.016562] NET: Registered protocol family 1
[ 0.016586] PCI: CLS 0 bytes, default 64
[ 0.017261] workingset: timestamp_bits=62 max_order=17 bucket_order=0
[ 0.019005] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.019015] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.027817] mtk-pcie 11280000.pcie: host bridge /pcie@11280000 ranges:
[ 0.027828] mtk-pcie 11280000.pcie: Parsing ranges property...
[ 0.027834] mtk-pcie 11280000.pcie: MEM 0x20000000..0x2fffffff -> 0x20000000
[ 0.235392] mtk-pcie 11280000.pcie: PCIe link down, ltssm reg val: 0x1000001
[ 0.235447] mtk-pcie: probe of 11280000.pcie failed with error -110
[ 0.242974] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.243451] printk: console [ttyS0] disabled
[ 0.263571] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 12, base_baud = 2500000) is a ST16650V2
[ 0.944134] printk: console [ttyS0] enabled
[ 0.968665] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 13, base_baud = 1625000) is a ST16650V2
[ 0.998101] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 14, base_baud = 1625000) is a ST16650V2
[ 1.007647] mtk_rng 1020f000.trng: registered RNG driver
[ 1.007873] random: fast init done
[ 1.013063] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 1.016580] random: crng init done
[ 1.023962] loop: module loaded
[ 1.030157] spi-nor spi0.0: unrecognized JEDEC id bytes: ff c8 01 7f 7f 7f
[ 1.037039] spi-nor: probe of spi0.0 failed with error -2
[ 1.042565] spi-nand spi0.1: GigaDevice/ESMT SPI NAND was found.
[ 1.048565] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 1.057637] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 1.065004] libphy: Fixed MDIO Bus: probed
[ 1.069475] tun: Universal TUN/TAP device driver, 1.6
[ 1.074678] mtk_probe none-cache-api init !
[ 1.079030] mtk_hw_init 3055 pending:0
[ 1.082851] mtk_hw_init 3060 pn-clk init
[ 1.086868] mtk_hw_init 3069
[ 1.089822] mtk_hw_init 3086
[ 1.092778] mtk_eth_cold_reset 2975
[ 1.107340] ethsys_reset 2852 i:0 set:c0800040 read:6000004 reset:1
[ 1.113590] ############ mtk_eth_fe_reset_update 1555 val:c0800040 fe_reset.val_s:c0800040
[ 1.121918] ############ mtk_eth_fe_reset_update 1559 val:6000004 fe_reset.val_r:6000004
[ 1.130072] ############ mtk_eth_fe_reset_update 1572 val:0 fe_reset.cold_cnt:1
[ 1.137446] mtk_hw_init 3094 read 0 rstctl:0
[ 1.137447] mtk_hw_init 3095
[ 1.144654] mtk_hw_init 3103 FE/PPE/GMAC reset done
[ 1.149702] mtk_probe 4263 fe-irq:127
[ 1.153490] libphy: mdio: probed
[ 1.201582] mtk_soc_eth 15100000.ethernet: generated random MAC address de:20:67:c6:42:fa
[ 1.209961] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc011a00000, irq 124
[ 1.219092] mtk_soc_eth 15100000.ethernet: generated random MAC address 2e:b3:00:75:bc:93
[ 1.227407] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc011a00000, irq 124
[ 1.236519] (unnamed net_device) (dummy): netif_napi_add() called with weight 256
[ 1.244022] 500210440 -> init fe_reset
[ 1.247846] [mtk_probe] mtk_dma_monitor_timer is initialized !
[ 1.253830] i2c /dev entries driver
[ 1.258285] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.266163] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: [email protected]
[ 1.274875] leds-hm0807a spi1.0: led_driver_probe
[ 1.279571] leds-hm0807a spi1.0: chip_num:5, led_num:5.
[ 1.284782] leds-hm0807a spi1.0: led_driver_probe name:led_red
[ 1.290628] leds-hm0807a spi1.0: led_driver_probe name:led_blue
[ 1.296809] leds-hm0807a spi1.0: led_driver_probe name:led_yellow
[ 1.302912] leds-hm0807a spi1.0: led_driver_probe name:led_white
[ 1.308927] leds-hm0807a spi1.0: led_driver_probe name:led_green
[ 1.315120] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433,alg:7fcdfc00
[ 1.328094] Initializing XFRM netlink socket
[ 1.332571] NET: Registered protocol family 10
[ 1.337472] Segment Routing with IPv6
[ 1.341167] NET: Registered protocol family 17
[ 1.345606] NET: Registered protocol family 15
[ 1.350059] Bridge firewalling registered
[ 1.354055] 8021q: 802.1Q VLAN Support v1.8
[ 1.358728] pstore: Using crash dump compression: deflate
[ 1.370324] nmbm nmbm_spim_nand: Signature found at block 1023 [0x07fe0000]
[ 1.378152] nmbm nmbm_spim_nand: First info table with writecount 0 found in block 960
[ 1.388640] nmbm nmbm_spim_nand: Second info table with writecount 0 found in block 963
[ 1.396641] nmbm nmbm_spim_nand: NMBM has been successfully attached
[ 1.403193] 10 fixed-partitions partitions found on MTD device nmbm_spim_nand
[ 1.410312] Creating 10 MTD partitions on "nmbm_spim_nand":
[ 1.415869] 0x000000000000-0x000000100000 : "BL2"
[ 1.420965] 0x000000100000-0x000000140000 : "Nvram"
[ 1.426115] 0x000000140000-0x000000180000 : "Bdata"
[ 1.431252] 0x000000180000-0x000000380000 : "Factory"
[ 1.436565] 0x000000380000-0x000000580000 : "FIP"
[ 1.441531] 0x000000580000-0x0000005c0000 : "crash"
[ 1.446672] 0x0000005c0000-0x000000600000 : "crash_log"
[ 1.452178] 0x000000600000-0x000002400000 : "ubi"
[ 1.457185] 0x000002400000-0x000004200000 : "ubi1"
[ 1.462282] 0x000004200000-0x000007400000 : "overlay"
[ 2.019402] mt753x gsw@0: LAN/WAN VLAN setting=llllw
[ 2.024626] mt753x gsw@0: Switch is MediaTek MT7531AE rev 1
[ 2.034039] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz
[ 4.063757] libphy: mt753x_mdio: probed
[ 4.067625] init port map proc seccess!
[ 5.681177] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION:
[ 5.692959] mt753x gsw@0: -------- gephy-calbration (port:0) --------
[ 5.708146] CALDLY = 40
[ 5.775868] 0x1e-e0 = 2a2a
[ 5.780260] 0x1f-115 = 5
[ 5.782777] GE Rext AnaCal Done! (10)(0x2a)
[ 5.860533] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 5.933696] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 6.006860] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 6.084577] GE R50 AnaCal Done! (14) (0x24)(0xa4)
[ 6.092417] GE 1e_174(0xa6a6), 1e_175(0xa6a4)
[ 6.129651] GE Tx offset AnaCal Done! (pair-0)(2)(0x21) 0x1e_172=0x2120
[ 6.163595] GE Tx offset AnaCal Done! (pair-1)(4)(0x23) 0x1e_172=0x2123
[ 6.188437] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120
[ 6.213280] GE Tx offset AnaCal Done! (pair-3)(2)(0x2) 0x1e_173=0x2102
[ 6.310410] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x741d)
[ 6.416231] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2525)
[ 6.463262] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1a22)
[ 6.532923] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1f27)
[ 6.579586] PORT 0 RX_DC_OFFSET
[ 6.592237] before pairA output = 1d
[ 6.597580] after pairA output = fe
[ 6.602755] before pairB output = 1e
[ 6.608097] after pairB output = 1
[ 6.613186] before pairC output = d
[ 6.618441] after pairC output = 0
[ 6.623532] before pairD output = 1e
[ 6.628870] after pairD output = ff
[ 6.632601] mt753x gsw@0: -------- gephy-calbration (port:1) --------
[ 6.647788] CALDLY = 40
[ 6.728046] GE R50 AnaCal Done! (15) (0x23)(0xa3)
[ 6.810313] GE R50 AnaCal Done! (15) (0x23)(0xa3)
[ 6.878928] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 6.947545] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 6.955385] GE 1e_174(0xa3a3), 1e_175(0xb0b0)
[ 7.006269] GE Tx offset AnaCal Done! (pair-0)(5)(0x5) 0x1e_172=0x520
[ 7.030939] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x521
[ 7.055694] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120
[ 7.085088] GE Tx offset AnaCal Done! (pair-3)(3)(0x22) 0x1e_173=0x2122
[ 7.154017] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5415)
[ 7.214576] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1e1e)
[ 7.267264] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1c24)
[ 7.331267] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1e26)
[ 7.377929] PORT 1 RX_DC_OFFSET
[ 7.390582] before pairA output = e
[ 7.395837] after pairA output = 1
[ 7.400924] before pairB output = f
[ 7.406179] after pairB output = ff
[ 7.411354] before pairC output = 1e
[ 7.416696] after pairC output = 0
[ 7.421785] before pairD output = f
[ 7.427040] after pairD output = 1
[ 7.430684] mt753x gsw@0: -------- gephy-calbration (port:2) --------
[ 7.445870] CALDLY = 40
[ 7.507931] GE R50 AnaCal Done! (11) (0x31)(0xb1)
[ 7.576543] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 7.645157] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 7.713771] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 7.721611] GE 1e_174(0xb1b0), 1e_175(0xb0b0)
[ 7.772498] GE Tx offset AnaCal Done! (pair-0)(5)(0x24) 0x1e_172=0x2420
[ 7.797343] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2421
[ 7.822185] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120
[ 7.856129] GE Tx offset AnaCal Done! (pair-3)(4)(0x23) 0x1e_173=0x2123
[ 7.925059] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5816)
[ 7.979961] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1c1c)
[ 8.026994] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1c24)
[ 8.074025] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x131b)
[ 8.120687] PORT 2 RX_DC_OFFSET
[ 8.133342] before pairA output = 1e
[ 8.138684] after pairA output = 0
[ 8.143772] before pairB output = 1e
[ 8.149111] after pairB output = 0
[ 8.154200] before pairC output = d
[ 8.159455] after pairC output = ff
[ 8.164627] before pairD output = e
[ 8.169883] after pairD output = 0
[ 8.173526] mt753x gsw@0: -------- gephy-calbration (port:3) --------
[ 8.188713] CALDLY = 40
[ 8.259874] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 8.328489] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 8.401656] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 8.465720] GE R50 AnaCal Done! (11) (0x31)(0xb1)
[ 8.473561] GE 1e_174(0xa6b0), 1e_175(0xa6b1)
[ 8.519896] GE Tx offset AnaCal Done! (pair-0)(4)(0x23) 0x1e_172=0x2320
[ 8.544738] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2321
[ 8.569581] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120
[ 8.594425] GE Tx offset AnaCal Done! (pair-3)(2)(0x21) 0x1e_173=0x2121
[ 8.669013] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6c1b)
[ 8.740886] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2020)
[ 8.810547] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2028)
[ 8.840611] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x171f)
[ 8.887273] PORT 3 RX_DC_OFFSET
[ 8.899926] before pairA output = f
[ 8.905181] after pairA output = ff
[ 8.910356] before pairB output = f
[ 8.915611] after pairB output = ff
[ 8.920783] before pairC output = 1e
[ 8.926125] after pairC output = 0
[ 8.931214] before pairD output = 1e
[ 8.936557] after pairD output = ff
[ 8.940288] mt753x gsw@0: -------- gephy-calbration (port:4) --------
[ 8.955476] CALDLY = 40
[ 9.012982] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 9.072498] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 9.127459] GE R50 AnaCal Done! (9) (0x34)(0xb4)
[ 9.186887] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 9.194729] GE 1e_174(0xb2b2), 1e_175(0xb4b2)
[ 9.227414] GE Tx offset AnaCal Done! (pair-0)(1)(0x1) 0x1e_172=0x120
[ 9.265736] GE Tx offset AnaCal Done! (pair-1)(5)(0x24) 0x1e_172=0x124
[ 9.295045] GE Tx offset AnaCal Done! (pair-2)(3)(0x22) 0x1e_173=0x2220
[ 9.319887] GE Tx offset AnaCal Done! (pair-3)(2)(0x21) 0x1e_173=0x2221
[ 9.383160] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5c17)
[ 9.438063] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1212)
[ 9.490753] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x131b)
[ 9.526470] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x161e)
[ 9.573133] PORT 4 RX_DC_OFFSET
[ 9.585786] before pairA output = 1d
[ 9.591129] after pairA output = ff
[ 9.596304] before pairB output = e
[ 9.601560] after pairB output = ff
[ 9.606735] before pairC output = 1d
[ 9.612078] after pairC output = 0
[ 9.617167] before pairD output = f
[ 9.622422] after pairD output = 0
[ 9.628243] UBI: auto-attach mtd9
[ 9.631555] ubi0: attaching mtd9
[ 9.727410] ubi0: scanning is finished
[ 9.735705] ubi0: attached mtd9 (name "ubi1", size 30 MiB)
[ 9.741177] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 9.748032] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 9.754799] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 9.761740] ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
[ 9.767727] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 9.774928] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 662404348
[ 9.783948] ubi0: available PEBs: 64, total reserved PEBs: 176, PEBs reserved for bad PEB handling: 19
[ 9.793233] ubi0: background thread "ubi_bgt0d" started, PID 831
[ 9.793774] block ubiblock0_1: created from ubi0:1(rootfs)
[ 9.804692] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 9.811637] hctosys: unable to open rtc device (rtc0)
[ 9.829487] Failed to lock mtd obr
[ 9.831810] VFS: Mounted root (squashfs filesystem) readonly on device 253:0.
[ 9.842532] Freeing unused kernel memory: 448K
[ 9.859397] Run /sbin/init as init process
[ 10.034777] init: Console is alive
[ 10.038275] init: - watchdog -
[ 10.296260] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 10.318339] conninfra@(mtk_conninfra_drv_init:644) Before platform_driver_register
[ 10.326025] Get Index(0-TOP_MISC_BASE) phy_addr(0x11d10000) vir_addr=(0xffffffc010a6d000) size=(0x1000)
[ 10.335401] Get Index(1-TOPRGU_BASE) phy_addr(0x1001c000) vir_addr=(0xffffffc010a75000) size=(0x1000)
[ 10.344598] Get Index(2-GPIO_BASE) phy_addr(0x1001f000) vir_addr=(0xffffffc010a7d000) size=(0x1000)
[ 10.353621] Get Index(3-IOCFG_TR_BASE) phy_addr(0x11f00000) vir_addr=(0xffffffc010a85000) size=(0x1000)
[ 10.362990] Get Index(4-IOCFG_TL_BASE) phy_addr(0x11f10000) vir_addr=(0xffffffc010a8d000) size=(0x1000)
[ 10.372360] Get Index(5-INFRACFG_AO_BASE) phy_addr(0x10003000) vir_addr=(0xffffffc010a95000) size=(0x1000)
[ 10.381989] Get Index(6-CONN_INFRA_CFG_BASE) phy_addr(0x18001000) vir_addr=(0xffffffc010a9d000) size=(0x1000)
[ 10.391879] Get Index(7-CONN_INFRA_SYSRAM_BASE) phy_addr(0x18050000) vir_addr=(0xffffffc010aa5000) size=(0x1000)
[ 10.402028] Get Index(8-CONN_INFRA_CLKGEN_ON_TOP_BASE) phy_addr(0x18009000) vir_addr=(0xffffffc010aad000) size=(0x1000)
[ 10.412784] Get Index(9-CONN_HOST_CSR_TOP_BASE) phy_addr(0x18060000) vir_addr=(0xffffffc010ab5000) size=(0x1000)
[ 10.422934] Get Index(10-CONN_INFRA_BUS_CR_BASE) phy_addr(0x1800e000) vir_addr=(0xffffffc010abd000) size=(0x1000)
[ 10.433171] Get Index(11-CONN_INFRA_RGU_BASE) phy_addr(0x18000000) vir_addr=(0xffffffc010ac5000) size=(0x1000)
[ 10.443149] Get Index(12-CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18005000) vir_addr=(0xffffffc010acd000) size=(0x1000)
[ 10.453559] Get Index(13-INST2_CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18085000) vir_addr=(0xffffffc010acf000) size=(0x1000)
[ 10.464487] Get Index(14-CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18004000) vir_addr=(0xffffffc010ad1000) size=(0x1000)
[ 10.474896] Get Index(15-INST2_CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18084000) vir_addr=(0xffffffc010ad3000) size=(0x1000)
[ 10.485826] Get Index(16-CONN_SEMAPHORE_BASE) phy_addr(0x18070000) vir_addr=(0xffffffc010b60000) size=(0x10000)
[ 10.495889] Get Index(17-CONN_AFE_CTL_BASE) phy_addr(0x18003000) vir_addr=(0xffffffc010ad5000) size=(0x1000)
[ 10.505691] Get Index(18-CONN_AFE_CTL_2ND_BASE) phy_addr(0x18083000) vir_addr=(0xffffffc010ad7000) size=(0x1000)
[ 10.515841] Get Index(19-WF_TOP_SLPPROT_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010b80000) size=(0x10000)
[ 10.526163] Get Index(20-WF_TOP_CFG_BASE) phy_addr(0x184b0000) vir_addr=(0xffffffc010ad9000) size=(0x1000)
[ 10.535792] Get Index(21-WF_MCU_CONFIG_LS_BASE) phy_addr(0x184f0000) vir_addr=(0xffffffc010adb000) size=(0x1000)
[ 10.545940] Get Index(22-WF_MCU_BUS_CR_BASE) phy_addr(0x18400000) vir_addr=(0xffffffc010add000) size=(0x1000)
[ 10.555829] Get Index(23-WF_MCUSYS_INFRA_BUS_FULL_U_DEBUG_CTRL_AO_BASE) phy_addr(0x18500000) vir_addr=(0xffffffc010adf000) size=(0x1000)
[ 10.568059] Get Index(24-WF_TOP_CFG_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010ba0000) size=(0x10000)
[ 10.578266] eeFlashId: 0x7986, EEPROM_content_valid = 1
[ 10.578646] conninfra@(consys_plt_hw_init:221) tx_stream = 0x4, rx_stream = 0x4, band0_pa_type = 0x3, band1_pa_type = 0x3
[ 10.595741] conninfra@(consys_plt_hw_init:230) adie_cfg_type = 2, one_adie_dbdc = 0
[ 10.603382] [emi_mng_init] gConEmiPhyBase = [0x4fc00000] size = [0x100000] fw size = [0x100000] ops=[000000005f17f150]
[ 10.614123] conninfra@(mtk_conninfra_drv_init:650) After platform_driver_register
[ 10.621852] ConnInfra Dev: init (0)
[ 10.626820] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000)
[ 10.636628] conninfra@(consys_bus_clock_ctrl:485) drv=[4] conninfra_bus_clock_wpll=[0]->[16] enable
[ 10.645654] conninfra@(connsys_d_die_cfg:530) D-die efuse: 0x00000000
[ 10.653109] conninfra@(_connsys_a_die_chip_id_confirm:1915) adie_idx[0]: A-die CHIP ID = 0x7976, HW Version = 0x8a20
[ 10.664613] conninfra@(_connsys_a_die_chip_id_confirm:1915) adie_idx[1]: A-die CHIP ID = 0x7976, HW Version = 0x8a20
[ 10.677124] conninfra@(consys_spi_write_nolock:670) addr = 0x0a00, val = 0xffffffff
[ 10.685764] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002
[ 10.695410] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x00000000
[ 10.705056] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x43a60000
[ 10.718730] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b2, 0x00000000]
[ 10.730230] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002
[ 10.739877] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a6003a
[ 10.749523] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63a7003a
[ 10.763196] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b2, 0x00000000]
[ 10.774696] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002
[ 10.784342] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a7003a
[ 10.793989] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63ac003a
[ 10.807663] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b2, 0x00000000]
[ 10.819162] conninfra@(consys_spi_write_nolock:670) addr = 0x0038, val = 0x4a563b00
[ 10.827805] conninfra@(consys_spi_write_nolock:670) addr = 0x065c, val = 0x1d59080f
[ 10.836444] conninfra@(consys_spi_write_nolock:670) addr = 0x0664, val = 0x34c00fe0
[ 10.846094] conninfra@(consys_spi_write_nolock:670) addr = 0x0a00, val = 0xffffffff
[ 10.854734] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002
[ 10.864380] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x00000000
[ 10.874025] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x43a60000
[ 10.887700] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008800bf, 0x00000000]
[ 10.899199] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002
[ 10.908845] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a6003a
[ 10.918492] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63a7003a
[ 10.932165] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008800bf, 0x00000000]
[ 10.943665] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002
[ 10.953311] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a7003a
[ 10.962957] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63ac003a
[ 10.976631] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008800bf, 0x00000000]
[ 10.988130] conninfra@(consys_spi_write_nolock:670) addr = 0x0038, val = 0x4a563b00
[ 10.996770] conninfra@(consys_spi_write_nolock:670) addr = 0x065c, val = 0x1d59080f
[ 11.005410] conninfra@(consys_spi_write_nolock:670) addr = 0x0664, val = 0x34c00fe0
[ 11.014051] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x88888005
[ 11.023649] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x00000005
[ 11.032290] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x88888005
[ 11.041888] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x00000005
[ 11.050467] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000)
[ 11.060268] conninfra@(_consys_hw_conninfra_wakeup:470) conninfra_wakeup refcnt=[0]->[1] wakeup!!
[ 11.069125] conninfra@(_consys_hw_conninfra_sleep:490) conninfra_sleep refcnt=[1]->[0] sleep!!
[ 11.077713] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[0] CONNINFRA=[1]
[ 11.088601] Button Hotplug driver version 0.4.1
[ 11.094558] mediatek_soc_hnat 15100000.hnat: wan = eth1
[ 11.099790] mediatek_soc_hnat 15100000.hnat: lan = eth0
[ 11.105001] mediatek_soc_hnat 15100000.hnat: ppd = eth0
[ 11.110212] get_vlan_if_in_br:51 dev_get_by_name failed.
[ 11.115509] mediatek_soc_hnat 15100000.hnat: gmac num = 2
[ 11.120891] mediatek_soc_hnat 15100000.hnat: ppe num = 1
[ 11.126538] mediatek_soc_hnat 15100000.hnat: PPE0 entry number = 8192
[ 11.163368] mediatek_soc_hnat 15100000.hnat: PPE0 hwnat start
[ 11.187396] hnat roaming work enable
[ 11.193387] warp_module_init(): module init and register callback for warp
[ 11.200287] create warp_ctrl ok!!!
[ 11.203709] wed_get_slot_map(): assign slot_id:0 for entry: 0!
[ 11.209536] wed_get_slot_map(): assign slot_id:1 for entry: 1!
[ 11.215712] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 11.230184] init: - preinit -
[ 11.388576] mtk_soc_eth 15100000.ethernet: [mtk_open][2701] name:eth0 dma_refcnt:0
[ 11.398944] mtk_soc_eth 15100000.ethernet: [mtk_open][2708] name:eth0 dma_refcnt:0
[ 11.406591] mtk_soc_eth 15100000.ethernet: [mtk_open][2737] name:eth0 dma_refcnt:1
[ 11.414229] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 11.422528] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 14.490612] mount_root: mounting /dev/root
[ 14.758424] ubi1: attaching mtd10
[ 14.915195] ubi1: scanning is finished
[ 14.923637] ubi1: attached mtd10 (name "overlay", size 50 MiB)
[ 14.929459] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 14.936313] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 14.943082] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 14.950023] ubi1: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 14.956010] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 14.963211] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 2050416285
[ 14.972318] ubi1: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 19
[ 14.981516] ubi1: background thread "ubi_bgt1d" started, PID 936
UBI device number 1, total 400 LEBs (50790400 bytes, 48.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
ubimkvol: error!: UBI device doe[ 15.009571] UBIFS (ubi1:0): Mounting in unauthenticated mode
s not have free [ 15.015824] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 947
logical eraseblocks
[ 15.039418] UBIFS (ubi1:0): recovery needed
[ 15.148705] UBIFS (ubi1:0): recovery completed
[ 15.153181] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "data"
[ 15.160385] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.170275] UBIFS (ubi1:0): FS size: 46600192 bytes (44 MiB, 367 LEBs), journal size 2285568 bytes (2 MiB, 18 LEBs)
[ 15.180683] UBIFS (ubi1:0): reserved for root: 2201041 bytes (2149 KiB)
[ 15.187278] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID D02C2546-844B-49D9-96EE-E497C2A23542, small LPT model
[ 15.205708] urandom-seed: Seed file not found (/etc/urandom.seed)
do_mount_bind_etc...
[ 15.404888] procd: - early -
[ 15.407799] procd: - watchdog -
[ 15.920584] procd: - watchdog -
[ 15.923826] procd: - ubus -
[ 15.976693] procd: - init -
/etc/rc.d/S00sysfixtime: Tue Aug 30 15:31:29 UTC 2022
/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/net_cls failed: Resource busy
[ 16.072839] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.084797] l2tp_core: L2TP core driver, V2.0
[ 16.089709] l2tp_netlink: L2TP netlink interface
[ 16.094812] gre: GRE over IPv4 demultiplexor driver
[ 16.100430] ip_gre: GRE over IPv4 tunneling driver
[ 16.107779] ip6_gre: GRE over IPv6 tunneling driver
[ 16.125687] u32 classifier
[ 16.128407] input device check on
[ 16.922935] mt_wifi: module license 'Proprietary' taints kernel.
[ 16.928959] Disabling lock debugging due to kernel taint
[ 16.965738] conninfra@(conninfra_pwr_on:120) [conninfra_pwr_on] drv=[3]
[ 16.973294] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000)
[ 16.991138] Adie Type: 0x7976
[ 16.991139] SKU Type: 6000
[ 16.995050] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[1] CONNINFRA=[1]
[ 17.009108] WiFi@C12L1,get_dbg_setting_by_profile() 5238: debug level setting=INDEX0_debug_level not found!!
[ 17.018933] WiFi@C12L1,get_dbg_setting_by_profile() 5261: debug option setting=INDEX0_debug_option not found!!
[ 17.028973] mt_rbus 0000:00:00.0: runtime IRQ mapping not provided by arch
[ 17.041091] mt7986_init()-->
[ 17.044002]  sku:0xf, ADIE=MT7976 
[ 17.048346] <--mt7986_init()
[ 17.051237] RtmpRaDevCtrlInit(): MCS_LUT not used becasue MacTb size(544) > 128!
[ 17.058715] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX1
[ 17.066016] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX2
[ 17.073316] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX3
[ 17.080617] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX4
[ 17.087917] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX5
[ 17.095218] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX6
[ 17.102518] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX7
[ 17.109818] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX8
[ 17.117119] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX9
[ 17.124408] WiFi@C12L2,match_index_by_chipname() 512: Not find slot id, back to old rule.
[ 17.132650] msta_ifname not found
[ 17.142899] -->mtfwd_init(ver:2.0)
[ 17.142945] <--
[ 17.146964] mtk_warp_proxy: module uses symbols from proprietary module mt_wifi, inheriting taint.
[ 17.173662] ipt: xt_cgroup_MARK installed ok.
[ 17.184828] xt_time: kernel timezone is -0000
[ 17.190742] PPP generic driver version 2.4.2
[ 17.195535] PPP MPPE Compression module registered
[ 17.200790] NET: Registered protocol family 24
[ 17.205664] PPTP driver version 0.8.5
[ 17.210334] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 17.216061] kmodloader: done loading kernel modules from /etc/modules.d/*
/etc/rc.d/S19dnsmasq: cp: can't stat '/etc/dnsmasq.d/*': No such file or directory
/etc/rc.d/S19dnsmasq: sh: out of range
/etc/rc.d/S19dnsmasq: sh: out of range
[ 18.832993] tcp_life = 30
[ 18.835699] fin_life = 30
[ 18.838356] udp_life = 30
[ 18.841001] Binding Threshold =5
[ 20.427358] hook is going to be disabled !
[ 20.462329] hook is going to be enabled !
[ 20.485816] hook is going to be enabled !
/etc/rc.d/S21nginx: start fcgi-cgi by spawn-fcgi.
/etc/rc.d/S21nginx: start nginx ok.
/etc/rc.d/S49messagingagent.sh: start messagingagent ok.
[ 20.756066] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 20.761971] mtk_soc_eth 15100000.ethernet: [mtk_stop][2800] name:eth0 dma_refcnt:1
[ 20.769683] mtk_soc_eth 15100000.ethernet: [mtk_stop][2804] name:eth0 dma_refcnt:0
[ 20.916860] mtk_soc_eth 15100000.ethernet: [mtk_open][2701] name:eth0 dma_refcnt:0
[ 20.928149] mtk_soc_eth 15100000.ethernet: [mtk_open][2708] name:eth0 dma_refcnt:0
[ 20.935811] mtk_soc_eth 15100000.ethernet: [mtk_open][2737] name:eth0 dma_refcnt:1
[ 20.943469] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 20.951796] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 20.955708] br-lan: port 1(eth0.1) entered blocking state
[ 20.965842] br-lan: port 1(eth0.1) entered disabled state
[ 20.971451] device eth0.1 entered promiscuous mode
[ 20.976260] device eth0 entered promiscuous mode
[ 20.981189] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.987916] br-lan: port 1(eth0.1) entered blocking state
[ 20.993353] br-lan: port 1(eth0.1) entered forwarding state
[ 21.002600] br-lan: port 2(eth0.2) entered blocking state
[ 21.008028] br-lan: port 2(eth0.2) entered disabled state
[ 21.013718] device eth0.2 entered promiscuous mode
[ 21.018627] br-lan: port 2(eth0.2) entered blocking state
[ 21.024040] br-lan: port 2(eth0.2) entered forwarding state
[ 21.031390] br-lan: port 3(eth0.3) entered blocking state
[ 21.036792] br-lan: port 3(eth0.3) entered disabled state
[ 21.042656] device eth0.3 entered promiscuous mode
[ 21.047592] br-lan: port 3(eth0.3) entered blocking state
[ 21.053019] br-lan: port 3(eth0.3) entered forwarding state
[ 21.061026] br-lan: port 4(eth0.4) entered blocking state
[ 21.066468] br-lan: port 4(eth0.4) entered disabled state
[ 21.072061] device eth0.4 entered promiscuous mode
[ 21.076981] br-lan: port 4(eth0.4) entered blocking state
[ 21.082390] br-lan: port 4(eth0.4) entered forwarding state
[ 21.089804] br-lan: port 5(eth0.6) entered blocking state
[ 21.095269] br-lan: port 5(eth0.6) entered disabled state
[ 21.100900] device eth0.6 entered promiscuous mode
[ 21.105881] br-lan: port 5(eth0.6) entered blocking state
[ 21.111304] br-lan: port 5(eth0.6) entered forwarding state
[ 21.141883] mtk_soc_eth 15100000.ethernet: [mtk_open][2701] name:eth1 dma_refcnt:1
[ 21.149606] mtk_soc_eth 15100000.ethernet: [mtk_open][2737] name:eth1 dma_refcnt:2
[ 21.157273] mtk_soc_eth 15100000.ethernet eth1: configuring for fixed/2500base-x link mode
[ 21.165658] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 21.209779] hnat_priv ppd = eth0.6
[ 21.308666] WiFi@C01L2,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 21.317024] msta_ifname not found
[ 21.320991] warp_cap_support(): chip_id=7986 is in WHNAT support list
[ 21.327436] warp_entry_acquire(): bus slot:0, hook to WARP, entry id=0, entry: 00000000f4abf896
[ 21.336143] client_hif_specific_get(): hw->base_phy_addr 0x18000000!!
[ 21.342748] warp_entry_get_by_pdev(): return entry[0]
[ 21.347984] warp_msg_register():warp,pid,2906,id,0,wed_idx,0
[ 21.353738] wed_init(0): res_start = 0x15010000, size = 1000, irq=6,base_addr=0xffffffc01120b000
[ 21.363009] wed_ring_init(): wed tx ring init result = 0
[ 21.369023] wed_ring_init(): wed rx ring init result = 0
[ 21.378966] GetEntryFromFreeList: allocated new pool
[ 21.385744] GetEntryFromFreeList: allocated new pool
[ 21.392376] GetEntryFromFreeList: allocated new pool
[ 21.398635] GetEntryFromFreeList: allocated new pool
[ 21.406045] create wed ok!!!
[ 21.409022] wdma_init(): wdma(0) base_addr=0xffffffc01128d800, base_phy_addr=0x15104800
[ 21.417872] warp_woif_bus_init_hw(): bus:000000008d656138, txring: 20, pa: 0x00000000546b8000, 0x00000000546b8000, 24, 28, 3c
[ 21.429238] warp_woif_bus_init_hw(): bus:000000008d656138, rxring: 50, pa: 0x00000000546ba000, 0x00000000546ba000, 54, 58, 6c
[ 21.440589] get_region_info(): wed_idx = 0, base_addr = 0x000000004a084e42, size = 0x40000, res.start = 0x4fd00000, shared:0
[ 21.451837] get_region_info(): wed_idx = 0, base_addr = 0x00000000ab583308, size = 0x8000, res.start = 0x151e0000, shared:0
[ 21.463024] get_region_info(): wed_idx = 0, base_addr = 0x000000009dd17c6b, size = 0x240000, res.start = 0x4fd80000, shared:1
[ 21.474359] get_region_info(): wed_idx = 0, base_addr = 0x00000000068dd5be, size = 0x1000, res.start = 0x15194000, shared:0
[ 21.485480] warp_fwdl_mcu_mode(): mcu mode, need fwdl
[ 21.496498] ########## WO Firmware ##########
[ 21.500878] Chip ID: 0x0000
[ 21.503667] ECO version:0
[ 21.506280] Version: DEV_000000
[ 21.509427] Build date: 20220519213044
[ 21.513184] Total region:3
[ 21.515888] #################################
[ 21.520243] Parsing tailer region 0
[ 21.523723] Target address: 0x151e0000
[ 21.527548] Download size: 20400
[ 21.530875] Parsing tailer region 1
[ 21.534368] Target address: 0x4fd00000
[ 21.538219] Download size: 87072
[ 21.541621] Parsing tailer region 2
[ 21.545125] Target address: 0x4fd80000
[ 21.548970] Download size: 2283984
[ 21.554631] warp_fwdl_ready_check_mcu_mode(): waiting for wocpu
[ 21.580521] warp_fwdl_ready_check_mcu_mode(): wocpu is ready
[ 21.586250] warp_woctrl_init_state(), wo_state: WO_STATE_ENABLE
[ 21.592191] wo_proc_init done 00000000585998e4
[ 21.596728] wo_exep_proc_init done 00000000585998e4
[ 21.601740] wo_exception_init(0): exp log= 0x00000000f709e1bc, phy_addr= 0x0000000054360000 size= 32768
[ 21.611399] warp_probe(): probe fail since warp is full!
[ 21.616750] warp_dev0: probe of 15010000.wed2 failed with error -1
[ 21.627476] WiFi@C02L1,HwCtrlInit() 500: ser_init() return NDIS_STATUS_FAILURE
[ 21.693491] IFNAME[0]=wl1
[ 21.696389] IFNAME[1]=wl14
[ 21.699158] IFNAME[2]=wl13
[ 21.702041] IFNAME[3]=wl0
[ 21.704818] IFNAME[4]=wl5
[ 21.707573] IFNAME[5]=wl9
[ 21.710313] IFNAME[6]=wl15
[ 21.713133] RTMPSetProfileParameters(): Mbssid[0] miwifi_mesh = 0
[ 21.719237] RTMPSetProfileParameters(): Mbssid[1] miwifi_mesh = 0
[ 21.725348] RTMPSetProfileParameters(): Mbssid[2] miwifi_mesh = 0
[ 21.731443] RTMPSetProfileParameters(): Mbssid[3] miwifi_mesh = 0
[ 21.737551] RTMPSetProfileParameters(): Mbssid[4] miwifi_mesh = 0
[ 21.743640] RTMPSetProfileParameters(): Mbssid[5] miwifi_mesh = 0
[ 21.749735] RTMPSetProfileParameters(): Mbssid[6] miwifi_mesh = 0
[ 21.755923] RTMPSetProfileParameters(): Mbssid[0] backhaul = 0
[ 21.761762] RTMPSetProfileParameters(): Mbssid[1] backhaul = 0
[ 21.767593] RTMPSetProfileParameters(): Mbssid[2] backhaul = 0
[ 21.773435] RTMPSetProfileParameters(): Mbssid[3] backhaul = 0
[ 21.779277] RTMPSetProfileParameters(): Mbssid[4] backhaul = 1
[ 21.785118] RTMPSetProfileParameters(): Mbssid[5] backhaul = 0
[ 21.790952] RTMPSetProfileParameters(): Mbssid[6] backhaul = 0
[ 21.796894] RTMPSetProfileParameters(): Mbssid[0] mimesh_ver = 0
[ 21.802895] RTMPSetProfileParameters(): Mbssid[1] mimesh_ver = 0
[ 21.808889] RTMPSetProfileParameters(): Mbssid[2] mimesh_ver = 0
[ 21.814895] RTMPSetProfileParameters(): Mbssid[3] mimesh_ver = 4
[ 21.820896] RTMPSetProfileParameters(): Mbssid[4] mimesh_ver = 4
[ 21.826899] RTMPSetProfileParameters(): Mbssid[5] mimesh_ver = 0
[ 21.832898] RTMPSetProfileParameters(): Mbssid[6] mimesh_ver = 0
[ 21.838994] RTMPSetProfileParameters(): mesh_apmac = 24:CF:24:C3:BA:E4
[ 21.845629] RTMPSetProfileParameters(): mimesh_aplimit = 9
[ 21.851209] RTMPSetProfileParameters(): mimesh_id = 0x355e73f9
[ 21.857123] RTMPSetProfileParameters: mesh_model = RB06
[ 21.862801] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS0 PhyMode=78
[ 21.869409] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS1 PhyMode=78
[ 21.876009] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS2 PhyMode=78
[ 21.882610] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS3 PhyMode=177
[ 21.889302] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS4 PhyMode=177
[ 21.896006] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS5 PhyMode=177
[ 21.902699] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS6 PhyMode=177
[ 21.909628] WiFi@C23L2,auto_ch_select_set_cfg() 3398: BandIdx0, AutoChannelAtBootup=1, AutoChannelAlg = 3
[ 21.919180] WiFi@C23L2,auto_ch_select_set_cfg() 3398: BandIdx1, AutoChannelAtBootup=1, AutoChannelAlg = 3
[ 21.965317] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=0, Desired MFPC=0
[ 21.972727] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=1, Desired MFPC=0
[ 21.980115] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=2, Desired MFPC=0
[ 21.987516] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=3, Desired MFPC=0
[ 21.994902] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=4, Desired MFPC=0
[ 22.002284] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=5, Desired MFPC=0
[ 22.009705] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=6, Desired MFPC=0
[ 22.018471] WiFi@C12L1,RTMPSetProfileParameters() 8263: wl1, QoSMgmtCapa=0
[ 22.025352] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0
[ 22.032481] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0
[ 22.039630] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0
[ 22.046772] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0
[ 22.053910] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0
[ 22.061049] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0
[ 22.072873] WiFi@C12L1,rtmp_read_ap_client_from_file() 1566: APCLI[0] ApCliMuMimoDlEnable = 0
[ 22.081401] WiFi@C12L1,rtmp_read_ap_client_from_file() 1566: APCLI[1] ApCliMuMimoDlEnable = 0
/etc/rc.d/S60iwe[ 22.090050] WiFi@C12L1,rtmp_read_ap_client_from_file() 1585: APCLI[0] ApCliMuMimoUlEnable = 0
ventd: iwevent-c[ 22.099835] WiFi@C12L1,rtmp_read_ap_client_from_file() 1585: APCLI[1] ApCliMuMimoUlEnable = 0
all start ok
[ 22.111160] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[ 22.122406] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48
[ 22.130899] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[ 22.142124] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48
[ 22.207923] wdma_dma_ctrl(): WDMA_GLO_CFG=50404e70, txrx = 0
[ 22.219472] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e70, txrx = 0
[ 22.233710] warp_tx_ring_init_hw(): configure ring 0 setting
[ 22.239381] warp_tx_ring_init_hw(): wed:00000000c8bd214a wifi:000000001ef037cc: 24420=5cb38000,24424=2048,24428=0
[ 22.249646] warp_tx_ring_init_hw(): configure ring 1 setting
[ 22.255334] warp_tx_ring_init_hw(): wed:00000000c8bd214a wifi:000000001ef037cc: 24430=55c90000,24434=2048,24438=0
[ 22.265707] set_rrocfg,0
[ 22.291117] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e74, txrx = 3
[ 22.296970]  sku:0xf, ADIE=MT7976 
[ 22.301359] using E1 ROM patch
[ 22.304424] using E1 RAM
[ 22.306957] current sync CR = 0x1
[ 22.310271] Built date: 20220519212529a
[ 22.314213] Platform: ALPS
[ 22.317024] HW/SW version: 0x8a108a10
[ 22.320788] Patch version: 0xffffffff
[ 22.330881] current sync CR = 0x1
[ 22.334219] Chip ID: 0x0f
[ 22.336954] Eco version: 0x00
[ 22.340044] Region number: 0x0b
[ 22.343261] Format version: 0x02
[ 22.346577] Format flag: 0x01
[ 22.349627] Ram version: ____000000
[ 22.353216] Built date: 20220519212633
[ 22.357081] Common crc: 0xb8995b85
[ 22.360580] Release info: header tag = 0, total length = 108
[ 22.366343] tag 1, padding length = 1, tag length = 103
[ 22.371655] payload: t-neptune-main-2111-7986-imp_backup_wk2213-MT7986_E1_ASIC_ROM_RAM_REBB_IMP_BACKUP_WK2213-20220519212500
[ 22.401527] Chip ID: 0x00
[ 22.404239] Eco version: 0x00
[ 22.407277] Region number: 0x03
[ 22.410499] Format version: 0x02
[ 22.413803] Format flag: 0x01
[ 22.416845] Ram version: DEV_000000
[ 22.420411] Built date: 20220519213028
[ 22.424238] Common crc: 0x962f9340
[ 22.427715] Release info: header tag = 0, total length = 0
[ 22.527065] current sync CR = 0x7
[ 22.530394] efuse_probe: efuse = deaddead
[ 22.538987]  sku:0xf, ADIE=MT7976 
[ 22.544927] WiFi@C02L1,is_cal_free_ic() 1004: is_cal_free_ic(1004) offset:1000, 0,0 
[ 22.553354]  sku:0xf, ADIE=MT7976 
[ 22.571560]  sku:0xf, ADIE=MT7976 
[ 22.589943] WiFi@C02L1,is_cal_free_ic() 1023:  iCal free
[ 22.595934]  sku:0xf, ADIE=MT7976 
[ 26.458989] WiFi@C17L1,RTMPReadTxPwrPerRate() 450: (450): Don't Support this now!
[ 26.466505] WiFi@C01L1,AntCfgInit() 3020: Not support for HIF_MT yet!
[ 26.486540] ch_switch_monitor_state_machine_init:: enter
[ 26.491851] ch_switch_monitor_cfg_reset:: enter
[ 26.496375] ch_switch_monitor_cfg_reset:: enter
[ 26.501199] WiFi@C17L1,tx_pwr_comp_init() 641: NotSupportYet!
[ 26.507091] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 26.512566] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 26.518126] WiFi@C14L1,IPMacTable_init() 348: IPMacTable already inited!
[ 26.544941] wdma_dma_ctrl(): WDMA_GLO_CFG=58804e75, txrx = 3
[ 26.550676] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 26.556160] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 26.561589] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!!
[ 26.571484] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13447: DAT config band(0) cck_timeout Fail!
[ 26.580163] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!!
[ 26.590054] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13458: DAT config band(0) ofdm_timeout Fail!
[ 26.598818] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!!
[ 26.608710] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13469: DAT config band(0) ofdma_timeout Fail!
[ 26.617561] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!!
[ 26.627452] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13447: DAT config band(1) cck_timeout Fail!
[ 26.636131] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!!
[ 26.646023] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13458: DAT config band(1) ofdm_timeout Fail!
[ 26.654787] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!!
[ 26.664678] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13469: DAT config band(1) ofdma_timeout Fail!
[ 26.673584] mbss_create_vif: ifidx(1) idbss(1) final_name(wl14)
[ 26.679989] mbss_create_vif: ifidx(2) idbss(2) final_name(wl13)
[ 26.686732] mbss_create_vif: ifidx(1) idbss(4) final_name(wl5)
[ 26.693210] mbss_create_vif: ifidx(2) idbss(5) final_name(wl9)
[ 26.699584] mbss_create_vif: ifidx(3) idbss(6) final_name(wl15)
[ 26.706617] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 26.714848] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 26.920495] :(op = 0)
[ 26.922775] WiFi@C00L2,red_tail_drop_init() 83: red_tail_drop_init: available token:8192, whnat_en:1
[ 26.931901] WiFi@C00L1,MtCmdCr4RedSet() 913: MtCmdCr4RedSet: (ret = 0)
[ 26.938416] WiFi@C00L1,SendRedCmd() 1048: SendRedCmd:(ret = 1)
[ 26.944358] WiFi@C01L2,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 26.952348] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 0
[ 26.957922] WiFi@C23L1,DfsBuildChannelList() 3295: [RDM]: wdev is not 5G.
[ 26.964723] [RadarStateCheck] Zero Wait State: 0
[ 26.969328] phy_freq_adjust : no prim_ch value for adjust!
[ 26.974998] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
[ 26.982991] wdev_attr_update(): wdevId0 = 24:cf:24:c3:ba:e5
[ 26.988573] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band0 group_idx[0]=0, bw_grp=16 omac=0
[ 26.997688] WiFi@C23L1,HcGetBandByChannel() 1102: No hdev parking on channel:0, just return a default band_idx 0!
[ 27.007935] WiFi@C02L2,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn
[ 27.014728] WiFi@C00L2,ApAutoChannelAtBootUp() 289: ----------------->
[ 27.021336] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 27.026812] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 27.032405] WiFi@C08L1,UpdateBeaconHandler() 1979: wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x108/0x490 [mt_wifi])!!
[ 27.044711] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=1, ctrl_ch2=0, cent_ch=1 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 27.291616] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=2, ctrl_ch2=0, cent_ch=2 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 27.535623] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=3, ctrl_ch2=0, cent_ch=3 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 27.779613] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=4, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 28.023629] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=5, ctrl_ch2=0, cent_ch=5 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 28.267614] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=6, ctrl_ch2=0, cent_ch=6 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 28.511646] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=7, ctrl_ch2=0, cent_ch=7 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 28.755610] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=8, ctrl_ch2=0, cent_ch=8 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 28.999614] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=9, ctrl_ch2=0, cent_ch=9 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 29.243607] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=10, ctrl_ch2=0, cent_ch=10 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 29.487609] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=11, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1)
[ 29.731791] WiFi@C08L1,UpdateBeaconHandler() 1979: wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x2d0/0x490 [mt_wifi])!!
[ 29.744036] WiFi@C23L2,SelectClearChannelBusyTime() 1845: ====================================================================
[ 29.755408] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 1 : Busy Time = 9330, Skip Channel = FALSE, BwCap = TRUE
[ 29.766774] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 2 : Busy Time = 5782, Skip Channel = FALSE, BwCap = TRUE
[ 29.778140] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 3 : Busy Time = 14151, Skip Channel = FALSE, BwCap = TRUE
[ 29.789506] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 4 : Busy Time = 12141, Skip Channel = FALSE, BwCap = TRUE
[ 29.800872] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 5 : Busy Time = 6450, Skip Channel = FALSE, BwCap = TRUE
[ 29.812236] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 6 : Busy Time = 6668, Skip Channel = FALSE, BwCap = TRUE
[ 29.823602] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 7 : Busy Time = 2381, Skip Channel = FALSE, BwCap = TRUE
[ 29.834973] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 8 : Busy Time = 2626, Skip Channel = FALSE, BwCap = TRUE
[ 29.846340] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 9 : Busy Time = 2291, Skip Channel = FALSE, BwCap = TRUE
[ 29.857705] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 10 : Busy Time = 4446, Skip Channel = FALSE, BwCap = TRUE
[ 29.869071] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 11 : Busy Time = 7567, Skip Channel = FALSE, BwCap = TRUE
[ 29.880435] WiFi@C23L2,SelectClearChannelBusyTime() 1854: ====================================================================
[ 29.891806] WiFi@C23L2,SelectClearChannelBusyTime() 2088: Rule 3 Channel Busy time value : Select Primary Channel 9
[ 29.902219] WiFi@C23L2,SelectClearChannelBusyTime() 2090: Rule 3 Channel Busy time value : Min Channel Busy = 2291
[ 29.912545] WiFi@C23L2,SelectClearChannelBusyTime() 2095: Rule 3 Channel Busy time value : BW = 20
[ 29.921486] WiFi@C23L2,SelectClearChannelBusyTime() 2129: [SelectClearChannelBusyTime] - band0 END
[ 29.930451] WiFi@C23L1,operate_loader_phy() 401: oper_radio after decision: bw(1), prim_ch(9), cen_ch_1(11), cen_ch_2(0)!
[ 29.941444] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=9, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=1, TXStream=4, RXStream=4, scan(0)
[ 30.242880] WiFi@C23L1,DfsBuildChannelList() 3295: [RDM]: wdev is not 5G.
[ 30.249662] WiFi@C23L2,zero_wait_dfs_switch_ch() 779: outband ch 0, ch_stat 0
[ 30.257002] WiFi@C08L2,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:0, CfgMode:0
[ 30.267532] WiFi@C15L2,APPMFInit() 133: [PMF] apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 30.275065] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 30.282608] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(0)
[ 30.291206] WiFi@C01L2,wifi_sys_linkup() 1128: wdev idx = 0
[ 30.342112] WiFi@C03L1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 30.358258] WiFi@C00L1,TxCCKStreamCtrl() 21350: set wrong parameters
[ 30.373576] PrintSrCmd:
[ 30.373576] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.373576] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 30.387546] PrintSrCmd:
[ 30.387546] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.387546] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 30.401514] PrintSrCmd:
[ 30.401514] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.401514] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 30.415480] PrintSrCmd:
[ 30.415480] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.415480] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 30.429586] main_virtual_if_open(): net_device wl1 ifindex(10) up!
[ 30.430389] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0
[ 30.435756] mtk_ppe_dev_register_hook : ineterface wl1 register (1)
[ 30.450129] ip_acc_add_table(534): add succ (lan: 0)!
[ 30.452055] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl13
[ 30.455239] account_init succ!
[ 30.461303] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 30.472682] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 30.480972] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 2
[ 30.486721] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(1), prim_ch(9), cen_ch_1(11), cen_ch_2(0)!
/etc/rc.d/S77tra[ 30.498350] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
fficd: refresh i[ 30.507436] wdev_attr_update(): wdevId2 = 26:cf:24:a3:ba:e5
fname into ipaac[ 30.514384] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band0 group_idx[2]=9, bw_grp=16 omac=17
ount in [lan-dev[ 30.525066] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn
5g-wl 2.4g-wl w[ 30.533354] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: ----------------->
l-guest 5g-wl-ba[ 30.541068] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
ckhaul]
/etc/rc[ 30.547904] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
.d/S77trafficd: [ 30.554855] 7986@C00L1wl1,ApAutoChannelAtBootUp() 424: not A band
eth0 wl0 wl1 wl2[ 30.562249] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !!
wl14 wl15 wl5
[ 30.570760] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:2, CfgMode:0
/etc/rc.d/S77tra[ 30.582725] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=2, MFPC=0, MFPR=0, SHA256=0
fficd: trafficd [ 30.591879] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
start ok
[ 30.600605] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(2)
/etc/rc.d/S90mos[ 30.609797] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 2
quitto:
/etc/r[ 30.617327] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
c.d/S90mosquitto:
[ 30.635403] 7986@C00L1wl1,TxCCKStreamCtrl() 21350: set wrong parameters
[ 30.651031] PrintSrCmd:
[ 30.651031] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.651031] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 30.665055] PrintSrCmd:
[ 30.665055] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.665055] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 30.679086] PrintSrCmd:
[ 30.679086] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.679086] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 30.693063] PrintSrCmd:
[ 30.693063] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 30.693063] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 30.707190] mbss_virtual_if_open(): net_device wl13 ifindex(19) open!
[ 30.713638] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0
[ 30.720764] mtk_ppe_dev_register_hook : ineterface wl13 register (2)
[ 30.727772] br-miot: port 1(wl13) entered blocking state
[ 30.733090] br-miot: port 1(wl13) entered disabled state
[ 30.738583] device wl13 entered promiscuous mode
[ 30.743564] set_no_bcn(): net_device wl1 ifindex(10) up!
[ 30.748919] set_no_bcn(): Set no beacon as:0
[ 30.753313] br-miot: port 1(wl13) entered blocking state
[ 30.758644] br-miot: port 1(wl13) entered forwarding state
[ 30.768028] br-lan: port 6(wl1) entered blocking state
[ 30.773220] br-lan: port 6(wl1) entered disabled state
[ 30.778589] device wl1 entered promiscuous mode
[ 30.783269] br-lan: port 6(wl1) entered blocking state
[ 30.788429] br-lan: port 6(wl1) entered forwarding state
[ 30.807171] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl14
[ 30.813372] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 30.821750] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 30.830011] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 1
[ 30.835669] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(1), prim_ch(9), cen_ch_1(11), cen_ch_2(0)!
/etc/rc.d/S90mos[ 30.847210] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
quitto:
[ 30.856357] wdev_attr_update(): wdevId1 = 26:cf:24:93:ba:e5
[ 30.862720] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band0 group_idx[1]=10, bw_grp=16 omac=18
[ 30.872009] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn
/etc/rc.d/S90mos[ 30.879304] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: ----------------->
quitto:
[ 30.886863] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 30.893366] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 30.899040] 7986@C00L1wl1,ApAutoChannelAtBootUp() 424: not A band
[ 30.905186] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !!
[ 30.912308] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:1, CfgMode:0
[ 30.923126] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=1, MFPC=0, MFPR=0, SHA256=0
[ 30.930985] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 30.938610] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(1)
[ 30.947233] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 1
/etc/rc.d/S90mosquitto:
/etc/rc.d/S90mosquitto: /tmp/mq/cc/xiaoqiang_ct: OK
/etc/rc.d/S90mosquitto:
/etc/rc.d/S90mosquitto:
[ 30.998837] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 31.016069] 7986@C00L1wl1,TxCCKStreamCtrl() 21350: set wrong parameters
[ 31.031742] PrintSrCmd:
[ 31.031742] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 31.031742] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 31.045973] PrintSrCmd:
[ 31.045973] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 31.045973] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 31.060028] PrintSrCmd:
[ 31.060028] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 31.060028] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 31.074059] PrintSrCmd:
[ 31.074059] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
[ 31.074059] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[port_service] i[ 31.088327] mbss_virtual_if_open(): net_device wl14 ifindex(18) open!
nit services fin[ 31.096029] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0
ish
[ 31.104558] mtk_ppe_dev_register_hook : ineterface wl14 register (3)
/etc/init.d/network: Command failed: Not found
[ 31.137849] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl0
[ 31.143954] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 31.152333] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 31.160629] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 3
[ 31.166485] [RadarStateCheck] Zero Wait State: 0
[ 31.171151] 7986@C23L2wl1,RadarStateCheck() 292:  RD_NORMAL_MODE 
[ 31.178214] phy_freq_adjust : no prim_ch value for adjust!
[ 31.184024] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
[ 31.192046] wdev_attr_update(): wdevId3 = 24:cf:24:c3:ba:e6
[ 31.197682] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[3]=4, bw_grp=16 omac=0
[ 31.207994] 7986@C23L1wl1,HcGetBandByChannel() 1102: No hdev parking on channel:0, just return a default band_idx 0!
[ 31.218655] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn
[port_service] r[ 31.225856] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: ----------------->
ebuild map finis[ 31.233613] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
h
[ 31.240677] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 31.246450] 7986@C23L2wl1,AutoChSelBuildChannelListFor56G() 2702: ChListNum56G = 13
[ 31.254467] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(3) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x108/0x490 [mt_wifi])!!
[ 31.267093] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=36, ctrl_ch2=0, cent_ch=36 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1)
[port_service] remove vlan finish
[port_service] LIST_VID = -1
[ 31.318777] clean port 1 ifname
[ 31.322004] set port 1 ifname eth0.1
[port_service] create switch vlan: switch=switch0, ports=1 6t, vid=1
[port_service] create if: eth0.1
[ 31.348747] clean port 2 ifname
[ 31.351976] set port 2 ifname eth0.2
[port_service] create switch vlan: switch=switch0, ports=2 6t, vid=2
[port_service] create if: eth0.2
[ 31.383614] clean port 3 ifname
[ 31.386879] set port 3 ifname eth0.3
[port_service] create switch vlan: switch=switch0, ports=3 6t, vid=3
[port_service] create if: eth0.3
[ 31.426084] clean port 4 ifname
[ 31.429311] set port 4 ifname eth0.4
[port_service] create switch vlan: switch=switch0, ports=4 6t, vid=4
[port_service] create if: eth0.4
[port_service] create switch vlan: switch=switch0, ports=, vid=5
[port_service] create if: eth1.5
[port_service] create if: eth0.6
[port_service] reconfig vlan finish
[ 31.523678] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=40, ctrl_ch2=0, cent_ch=40 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1)
[ 31.779628] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=44, ctrl_ch2=0, cent_ch=44 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1)
[ 32.035675] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=48, ctrl_ch2=0, cent_ch=48 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1)
[ 32.143378] BcnCheck start after 3300 ms (wl1)
[ 32.148238] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(3) bss not ready (state:0, caller:update_ap_qload_to_bcn+0xa0/0xc8 [mt_wifi])!!
[ 32.291807] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(3) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x2d0/0x490 [mt_wifi])!!
[ 32.304315] 7986@C23L2wl1,SelectClearChannelBusyTime() 1845: ====================================================================
[ 32.315944] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 36 : Busy Time = 43, Skip Channel = FALSE, BwCap = TRUE
[ 32.327569] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 40 : Busy Time = 1918, Skip Channel = FALSE, BwCap = TRUE
[ 32.339194] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 44 : Busy Time = 168, Skip Channel = FALSE, BwCap = TRUE
[ 32.350824] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 48 : Busy Time = 57, Skip Channel = FALSE, BwCap = TRUE
[ 32.362460] 7986@C23L2wl1,SelectClearChannelBusyTime() 1854: ====================================================================
[ 32.374094] 7986@C23L2wl1,SelectClearChannelBusyTime() 2088: Rule 3 Channel Busy time value : Select Primary Channel 36
[ 32.384852] 7986@C23L2wl1,SelectClearChannelBusyTime() 2090: Rule 3 Channel Busy time value : Min Channel Busy = 1918
[ 32.395437] 7986@C23L2wl1,SelectClearChannelBusyTime() 2095: Rule 3 Channel Busy time value : BW = 160
[ 32.404724] 7986@C23L2wl1,SelectClearChannelBusyTime() 2129: [SelectClearChannelBusyTime] - band1 END
[ 32.413942] [RadarStateCheck] Zero Wait State: 0
[ 32.418551] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE 
[ 32.425685] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)!
[ 32.436963] new DFS channel 52 not pre dfs channel
[ 32.441743] 7986@C23L2wl1,DfsCacNormalStart() 3204: [RDM] CAC 65 seconds start . Disable MAC TX
[ 32.450499] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=36, ctrl_ch2=0, cent_ch=50 DBDCIdx=1, ChBand=1, BW=3, TXStream=4, RXStream=4, scan(0)
[ 32.500015] 7986@C23L2wl1,zero_wait_dfs_switch_ch() 779: outband ch 0, ch_stat 0
[ 32.507408] 7986@C23L2wl1,zero_wait_dfs_switch_ch() 786: bDedicatedZeroWaitDefault == 0
[ 32.515627] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:3, CfgMode:0
[ 32.526411] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=3, MFPC=0, MFPR=0, SHA256=0
[ 32.534202] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 32.541762] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(3)
[ 32.550358] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 3
[ 32.601584] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 32.629073] PrintSrCmd:
[ 32.629073] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 32.629073] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 32.643047] PrintSrCmd:
[ 32.643047] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 32.643047] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 32.657018] PrintSrCmd:
[ 32.657018] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 32.657018] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 32.670987] PrintSrCmd:
[ 32.670987] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 32.670987] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 32.685093] mbss_virtual_if_open(): net_device wl0 ifindex(20) open!
[ 32.685896] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0
[ 32.691443] mtk_ppe_dev_register_hook : ineterface wl0 register (4)
[ 32.711127] br-lan: port 7(wl0) entered blocking state
[ 32.716294] br-lan: port 7(wl0) entered disabled state
[ 32.721644] device wl0 entered promiscuous mode
[ 32.726308] br-lan: port 7(wl0) entered blocking state
[ 32.731457] br-lan: port 7(wl0) entered forwarding state
[ 32.751222] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl5
[ 32.757213] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 32.765668] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 32.773946] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 4
[ 32.779686] [RadarStateCheck] Zero Wait State: 0
[ 32.779896] [wandt filter] init success!
[ 32.784319] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE 
[ 32.795382] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=4 
[ 32.803481] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)!
[ 32.815031] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
[ 32.823038] wdev_attr_update(): wdevId4 = 26:cf:24:c3:ba:e5
[ 32.828640] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[4]=25, bw_grp=16 omac=17
[ 32.839205] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=1 RadioOn
[ 32.846480] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: ----------------->
[ 32.853370] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 32.859112] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 32.864758] 7986@C00L1wl1,ApAutoChannelAtBootUp() 418: zero-wait DFS is not enabled
[ 32.872396] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !!
[ 32.879474] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:4, CfgMode:0
[ 32.890258] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=4, MFPC=0, MFPR=0, SHA256=0
[ 32.898083] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 32.905640] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(4)
[ 32.914239] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 4
[ 32.965547] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 32.993551] PrintSrCmd:
[ 32.993551] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 32.993551] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.007527] PrintSrCmd:
[ 33.007527] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.007527] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 33.021500] PrintSrCmd:
[ 33.021500] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.021500] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.035473] PrintSrCmd:
[ 33.035473] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.035473] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.049560] mbss_virtual_if_open(): net_device wl5 ifindex(21) open!
[ 33.050379] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0
[ 33.055905] mtk_ppe_dev_register_hook : ineterface wl5 register (5)
[ 33.073933] br-lan: port 8(wl5) entered blocking state
[ 33.079106] br-lan: port 8(wl5) entered disabled state
[ 33.084468] device wl5 entered promiscuous mode
[ 33.089121] br-lan: port 8(wl5) entered blocking state
[ 33.094282] br-lan: port 8(wl5) entered forwarding state
[ 33.111953] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl9
[ 33.117875] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 33.126214] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 33.134466] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 5
[ 33.140059] [RadarStateCheck] Zero Wait State: 0
[ 33.144675] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE 
[ 33.151794] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=4 
[ 33.159871] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)!
[ 33.171356] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
[ 33.179349] wdev_attr_update(): wdevId5 = 26:cf:24:d3:ba:e5
[ 33.184928] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[5]=26, bw_grp=16 omac=18
[ 33.195355] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=1 RadioOn
[ 33.202411] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: ----------------->
[ 33.209277] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 33.215011] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 33.220667] 7986@C00L1wl1,ApAutoChannelAtBootUp() 418: zero-wait DFS is not enabled
[ 33.228307] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !!
[ 33.235386] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:5, CfgMode:0
[ 33.246172] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=5, MFPC=0, MFPR=0, SHA256=0
[ 33.253987] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 33.261535] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(5)
[ 33.270131] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 5
[ 33.276463] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 33.304505] PrintSrCmd:
[ 33.304505] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.304505] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.318480] PrintSrCmd:
[ 33.318480] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.318480] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 33.332470] PrintSrCmd:
[ 33.332470] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.332470] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.346448] PrintSrCmd:
[ 33.346448] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.346448] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.360610] mbss_virtual_if_open(): net_device wl9 ifindex(22) open!
[ 33.361377] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0
[ 33.366984] mtk_ppe_dev_register_hook : ineterface wl9 register (6)
[ 33.383277] br-lan: port 9(wl9) entered blocking state
[ 33.388440] br-lan: port 9(wl9) entered disabled state
[ 33.393755] device wl9 entered promiscuous mode
[ 33.398335] br-lan: port 9(wl9) entered blocking state
[ 33.403463] br-lan: port 9(wl9) entered forwarding state
[ 33.419860] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl15
[ 33.425864] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 33.434207] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 33.442463] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 6
[ 33.448051] [RadarStateCheck] Zero Wait State: 0
[ 33.452667] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE 
[ 33.459785] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=5 
[ 33.467864] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)!
[ 33.479346] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
[ 33.487340] wdev_attr_update(): wdevId6 = 26:cf:24:e3:ba:e5
[ 33.492924] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[6]=27, bw_grp=16 omac=19
[ 33.503245] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=1 RadioOn
[ 33.510302] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: ----------------->
[ 33.517167] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 33.522902] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0)
[ 33.528548] 7986@C00L1wl1,ApAutoChannelAtBootUp() 418: zero-wait DFS is not enabled
[ 33.536186] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !!
[ 33.543295] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:6, CfgMode:0
[ 33.554087] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=6, MFPC=0, MFPR=0, SHA256=0
[ 33.561867] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 33.569414] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(6)
[ 33.578011] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 6
[ 33.631773] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 33.659752] PrintSrCmd:
[ 33.659752] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.659752] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.673727] PrintSrCmd:
[ 33.673727] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.673727] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 33.687698] PrintSrCmd:
[ 33.687698] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.687698] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.701664] PrintSrCmd:
[ 33.701664] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 33.701664] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1
[ 33.715837] mbss_virtual_if_open(): net_device wl15 ifindex(23) open!
[ 33.716580] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0
[ 33.722273] mtk_ppe_dev_register_hook : ineterface wl15 register (7)
/etc/init.d/network: Command failed: Not found
[ 33.749192] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
[ 33.757559] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
[ 33.765832] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 8
[ 33.771432] [RadarStateCheck] Zero Wait State: 0
[ 33.776045] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE 
[ 33.783162] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=5 
[ 33.791240] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)!
[ 33.802734] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi]
[ 33.810732] wdev_attr_update(): wdevId8 = 2a:cf:24:c3:ba:e6
[ 33.817730] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi]
[ 33.825146] mtk_ppe_dev_register_hook : ineterface apclix0 register (8)
[ 33.834750] br-lan: port 10(apclix0) entered blocking state
[ 33.840450] br-lan: port 10(apclix0) entered disabled state
[ 33.846194] device apclix0 entered promiscuous mode
[ 33.868122] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl14
[ 33.874224] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN
[ 33.882897] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(1)
[ 33.892176] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(1) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!!
[ 33.903816] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 1
[ 33.910722] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 33.926026] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 1
[ 33.931790] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT
[ 33.940304] mbss_virtual_if_close(): net_device wl14 ifindex(18) close!
[ 33.946913] extif_put_dev(wl14)
[ 33.950043] mtk_ppe_dev_unregister_hook : ineterface wl14 set null (3)
[ 33.971406] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl13
[ 33.977502] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN
[ 33.986175] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(2)
[ 33.995465] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(2) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!!
[ 34.007169] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 2
[ 34.014073] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 34.029341] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 2
[ 34.035081] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT
[ 34.043590] mbss_virtual_if_close(): net_device wl13 ifindex(19) close!
[ 34.050191] extif_put_dev(wl13)
[ 34.053320] mtk_ppe_dev_unregister_hook : ineterface wl13 set null (2)
[ 34.059971] br-miot: port 1(wl13) entered disabled state
[ 34.090257] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl9
[ 34.096276] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN
[ 34.104949] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(5)
[ 34.114229] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(5) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!!
[ 34.125865] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 5
[ 34.132771] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 34.148131] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 5
[ 34.153875] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT
[ 34.162386] mbss_virtual_if_close(): net_device wl9 ifindex(22) close!
[ 34.168902] extif_put_dev(wl9)
[ 34.171945] mtk_ppe_dev_unregister_hook : ineterface wl9 set null (6)
[ 34.180619] br-lan: port 9(wl9) entered disabled state
[ 34.188335] device wl9 left promiscuous mode
[ 34.192794] br-lan: port 9(wl9) entered disabled state
[ 34.246330] ip_acc_set_table(602): set succ(lan)!
[ 34.279171] br-lan: port 1(eth0.1) entered disabled state
[ 34.287967] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl15
[ 34.294078] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN
[ 34.302807] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(6)
[ 34.312083] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(6) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!!
[ 34.323727] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 6
[ 34.330634] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1
[ 34.346082] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 6
[ 34.351906] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT
[ 34.360427] mbss_virtual_if_close(): net_device wl15 ifindex(23) close!
[ 34.363969] 7986@C09L2wl1,cntl_connect_request() 389: type=2,len=0,caller:ApCliIfUp+0x198/0x328 [mt_wifi]
[ 34.367050] extif_put_dev(wl15)
[ 34.376606] PrintSrCmd:
[ 34.376606] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 34.376606] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 34.379705] mtk_ppe_dev_unregister_hook : ineterface wl15 set null (7)
[ 34.400243] PrintSrCmd:
[ 34.400243] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
[ 34.400243] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
[ 34.414368] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN
[ 34.423056] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 8
[ 34.429004] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT
[ 34.437565] extif_put_dev(apclix0)
[ 34.440960] mtk_ppe_dev_unregister_hook : ineterface apclix0 set null (8)
[ 34.447887] br-lan: port 10(apclix0) entered disabled state
[ 34.453931] br-lan: port 2(eth0.2) entered disabled state
[ 34.459506] device apclix0 left promiscuous mode
[ 34.464160] br-lan: port 10(apclix0) entered disabled state
[ 34.491241] br-lan: port 3(eth0.3) entered disabled state
[ 34.500663] br-lan: port 4(eth0.4) entered disabled state
starting miwifi-roam success
/etc/init.d/network: Command failed: Not found
[ 34.582335] SetThermalProtectDisable(): band_idx: 0, protection_type: 1, trigger_type: 1
[ 34.591632] SetThermalProtectDisable(): band_idx: 1, protection_type: 1, trigger_type: 1
[ 34.600889] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 0, duty: 100
[ 34.608983] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 1, duty: 70
[ 34.617029] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 2, duty: 50
[ 34.624985] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 3, duty: 10
[ 34.632982] SetThermalProtectEnable(): band_idx: 0, protection_type: 1, trigger_type: 1
[ 34.640992] SetThermalProtectEnable(): trigger_temp: 106, restore_temp: 101, recheck_time: 5
[ 34.650430] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 0, duty: 100
[ 34.658501] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 1, duty: 70
[ 34.666397] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 2, duty: 50
[ 34.674366] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 3, duty: 10
[ 34.682291] SetThermalProtectEnable(): band_idx: 1, protection_type: 1, trigger_type: 1
[ 34.690296] SetThermalProtectEnable(): trigger_temp: 106, restore_temp: 101, recheck_time: 5
[ 34.903383] BcnCheck start after 800 ms (wl1)
[ 36.419381] 7986@C13L1wl0,MlmeEnqueueWithWdev() 5579: wdev(8) state: if down!
[port_service] build network finish
[port_service] all services have started
/etc/rc.d/S98miqos: miqos: delay 5s to wait for network ready.
[ 37.016527] hnat_priv ppd = eth0.6
/etc/rc.d/S99boot_check: : INFO: rcS timing 35.516058305s seconds.
Tue Aug 30 23:31:50 CST 2022 boot_check[5143]: Booting up finished.
/etc/rc.d/S99cab_meshd: exist, exit.
update cap mesh param done
BusyBox v1.25.1 (2022-08-12 09:08:13 UTC) built-in shell (ash)
-----------------------------------------------------
Welcome to XiaoQiang!
-----------------------------------------------------
$$$$$$\ $$$$$$$\ $$$$$$$$\ $$\ $$\ $$$$$$\ $$\ $$\
$$ __$$\ $$ __$$\ $$ _____| $$ | $$ | $$ __$$\ $$ | $$ |
$$ / $$ |$$ | $$ |$$ | $$ | $$ | $$ / $$ |$$ |$$ /
$$$$$$$$ |$$$$$$$ |$$$$$\ $$ | $$ | $$ | $$ |$$$$$ /
$$ __$$ |$$ __$$< $$ __| $$ | $$ | $$ | $$ |$$ $$<
$$ | $$ |$$ | $$ |$$ | $$ | $$ | $$ | $$ |$$ |\$$\
$$ | $$ |$$ | $$ |$$$$$$$$\ $$$$$$$$$ | $$$$$$ |$$ | \$$\
\__| \__|\__| \__|\________| \_________/ \______/ \__| \__|
root@XiaoQiang:/#
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment