Created
December 11, 2015 22:33
-
-
Save sr105/8c9873420c855f0bd0cf to your computer and use it in GitHub Desktop.
gsc wd disabled by power off
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| ########################################################################### | |
| ########################################################################### | |
| ########################################################################### | |
| U-Boot SPL 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| Booting from NAND | |
| PMIC: LTC3676 | |
| NAND : 256 MiB | |
| *** Warning - bad CRC, using default environment | |
| U-Boot 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| CPU: Freescale i.MX6DL rev1.2 at 792MHz | |
| CPU: Industrial temperature grade (-40C to 105C) at 58C | |
| Reset cause: POR | |
| I2C: ready | |
| DRAM: 1 GiB | |
| PMIC: LTC3676 | |
| NAND: 256 MiB | |
| MMC: FSL_SDHC: 0 | |
| *** Warning - bad CRC, using default environment | |
| PCI: | |
| 00:01.0 - 16c3:abcd - Bridge device | |
| 01:00.0 - 168c:0032 - Network controller | |
| auto-detected panel HDMI | |
| Display: HDMI (1024x768) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Gateworks Corporation Copyright 2014 | |
| Model: GW5100-SP325-D | |
| MFGDate: 05-15-2015 | |
| Serial:666445 | |
| GSC: v46 0xd0f9 WDT:enabled WDT_RESET board temp at 45C | |
| RTC: 1449604815 | |
| DIO0: GPIO1_IO16 (gpio-16) | |
| DIO1: GPIO1_IO19 (gpio-19) | |
| DIO2: GPIO1_IO17 (gpio-17) | |
| DIO3: GPIO1_IO18 (gpio-18) | |
| RS232: enabled | |
| Net: Phy 0 not found | |
| PHY reset timed out | |
| set ethprime to FEC | |
| FEC [PRIME] | |
| Error: FEC address not set. | |
| , usb_ether | |
| Error: usb_ether address not set. | |
| Hit any key to stop autoboot: 0 | |
| Attempting usb boot... | |
| starting USB... | |
| USB0: USB EHCI 1.00 | |
| scanning bus 0 for devices... cannot reset port 1!? | |
| 1 USB Device(s) found | |
| USB1: USB EHCI 1.00 | |
| scanning bus 1 for devices... 4 USB Device(s) found | |
| scanning usb for storage devices... 1 Storage Device(s) found | |
| scanning usb for ethernet devices... 0 Ethernet Device(s) found | |
| USB device 0: | |
| Device 0: Vendor: Generic Rev: 1.76 Prod: Ultra HS-SD/MMC | |
| Type: Removable Hard Disk | |
| Capacity: 7580.0 MB = 7.4 GB (15523840 x 512) | |
| ... is now current device | |
| 0 bytes read in 98 ms (0 Bytes/s) | |
| ## Executing script at 12000000 | |
| Wrong image format for "source" command | |
| ** File not found boot/uImage ** | |
| Attempting mmc boot... | |
| MMC: no card present | |
| MMC: no card present | |
| ** Bad device mmc 0 ** | |
| MMC: no card present | |
| ** Bad device mmc 0 ** | |
| Attempting sata boot... | |
| ** Bad device size - sata 0 ** | |
| ** Bad device size - sata 0 ** | |
| Attempting flash boot... | |
| UBI: attaching mtd1 to ubi0 | |
| UBI: scanning is finished | |
| UBI: attached mtd1 (name "mtd=2", size 239 MiB) to ubi0 | |
| UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | |
| UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | |
| UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 | |
| UBI: good PEBs: 1912, bad PEBs: 0, corrupted PEBs: 0 | |
| UBI: user volume: 0, internal volumes: 1, max. volumes count: 128 | |
| UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 669125316 | |
| UBI: available PEBs: 1868, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40 | |
| UBIFS not mounted, use ubifs mount to mount volume first! | |
| ubifsload - load file from an UBIFS filesystem | |
| Usage: | |
| ubifsload <addr> <filename> [bytes] | |
| - load file 'filename' to address 'addr' | |
| UBIFS not mounted, use ubifs mount to mount volume first! | |
| ubifsload - load file from an UBIFS filesystem | |
| Usage: | |
| ubifsload <addr> <filename> [bytes] | |
| - load file 'filename' to address 'addr' | |
| Ventana > | |
| ########################################################################### | |
| ########################################################################### | |
| ########################################################################### | |
| U-Boot SPL 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| Booting from NAND | |
| PMIC: LTC3676 | |
| NAND : 256 MiB | |
| *** Warning - bad CRC, using default environment | |
| U-Boot 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| CPU: Freescale i.MX6DL rev1.2 at 792MHz | |
| CPU: Industrial temperature grade (-40C to 105C) at 58C | |
| Reset cause: POR | |
| I2C: ready | |
| DRAM: 1 GiB | |
| PMIC: LTC3676 | |
| NAND: 256 MiB | |
| MMC: FSL_SDHC: 0 | |
| *** Warning - bad CRC, using default environment | |
| PCI: | |
| 00:01.0 - 16c3:abcd - Bridge device | |
| 01:00.0 - 168c:0032 - Network controller | |
| auto-detected panel HDMI | |
| Display: HDMI (1024x768) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Gateworks Corporation Copyright 2014 | |
| Model: GW5100-SP325-D | |
| MFGDate: 05-15-2015 | |
| Serial:666445 | |
| GSC: v46 0xd0f9 WDT:enabled WDT_RESET board temp at 45C | |
| RTC: 1449604848 | |
| DIO0: GPIO1_IO16 (gpio-16) | |
| DIO1: GPIO1_IO19 (gpio-19) | |
| DIO2: GPIO1_IO17 (gpio-17) | |
| DIO3: GPIO1_IO18 (gpio-18) | |
| RS232: enabled | |
| Net: Phy 0 not found | |
| PHY reset timed out | |
| set ethprime to FEC | |
| FEC [PRIME] | |
| Error: FEC address not set. | |
| , usb_ether | |
| Error: usb_ether address not set. | |
| Hit any key to stop autoboot: 0 | |
| Attempting usb boot... | |
| starting USB... | |
| USB0: USB EHCI 1.00 | |
| scanning bus 0 for devices... cu: Got hangup signal | |
| Disconnected. | |
| ########################################################################### | |
| ####### Power was removed and device relocated to another table. | |
| ########################################################################### | |
| silver-2:~ hchapman$ sudo cu -l /dev/tty.SLAB_USBtoUART -s 115200 --nostop | |
| Connected. | |
| ####### When I plugged in the unpowered DC adapter, It spit out the first | |
| ####### line from the SPL. | |
| U-Boot SPL 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| ########################################################################### | |
| ####### Power applied | |
| ########################################################################### | |
| U-Boot SPL 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| Booting from NAND | |
| PMIC: LTC3676 | |
| NAND : 256 MiB | |
| *** Warning - bad CRC, using default environment | |
| U-Boot 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| CPU: Freescale i.MX6DL rev1.2 at 792MHz | |
| CPU: Industrial temperature grade (-40C to 105C) at 31C | |
| Reset cause: POR | |
| I2C: ready | |
| DRAM: 1 GiB | |
| PMIC: LTC3676 | |
| NAND: 256 MiB | |
| MMC: FSL_SDHC: 0 | |
| *** Warning - bad CRC, using default environment | |
| PCI: | |
| 00:01.0 - 16c3:abcd - Bridge device | |
| 01:00.0 - 168c:0032 - Network controller | |
| No panel detected: default to HDMI | |
| Display: HDMI (1024x768) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Gateworks Corporation Copyright 2014 | |
| Model: GW5100-SP325-D | |
| MFGDate: 05-15-2015 | |
| Serial:666445 | |
| GSC: v46 0xd0f9 WDT:disabled board temp at 25C | |
| RTC: 1 | |
| DIO0: GPIO1_IO16 (gpio-16) | |
| DIO1: GPIO1_IO19 (gpio-19) | |
| DIO2: GPIO1_IO17 (gpio-17) | |
| DIO3: GPIO1_IO18 (gpio-18) | |
| RS232: enabled | |
| Net: Phy 0 not found | |
| PHY reset timed out | |
| set ethprime to FEC | |
| FEC [PRIME] | |
| Error: FEC address not set. | |
| , usb_ether | |
| Error: usb_ether address not set. | |
| Hit any key to stop autoboot: 0 | |
| Attempting usb boot... | |
| starting USB... | |
| USB0: Port not available. | |
| USB1: USB EHCI 1.00 | |
| scanning bus 1 for devices... 4 USB Device(s) found | |
| scanning usb for storage devices... 1 Storage Device(s) found | |
| scanning usb for ethernet devices... 0 Ethernet Device(s) found | |
| USB device 0: | |
| Device 0: Vendor: Generic Rev: 1.76 Prod: Ultra HS-SD/MMC | |
| Type: Removable Hard Disk | |
| Capacity: 7580.0 MB = 7.4 GB (15523840 x 512) | |
| ... is now current device | |
| 0 bytes read in 99 ms (0 Bytes/s) | |
| ## Executing script at 12000000 | |
| Wrong image format for "source" command | |
| ** File not found boot/uImage ** | |
| Attempting mmc boot... | |
| MMC: no card present | |
| MMC: no card present | |
| ** Bad device mmc 0 ** | |
| MMC: no card present | |
| ** Bad device mmc 0 ** | |
| Attempting sata boot... | |
| ** Bad device size - sata 0 ** | |
| ** Bad device size - sata 0 ** | |
| Attempting flash boot... | |
| UBI: attaching mtd1 to ubi0 | |
| UBI: scanning is finished | |
| UBI: attached mtd1 (name "mtd=2", size 239 MiB) to ubi0 | |
| UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | |
| UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | |
| UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 | |
| UBI: good PEBs: 1912, bad PEBs: 0, corrupted PEBs: 0 | |
| UBI: user volume: 0, internal volumes: 1, max. volumes count: 128 | |
| UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 669125316 | |
| UBI: available PEBs: 1868, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40 | |
| UBIFS not mounted, use ubifs mount to mount volume first! | |
| ubifsload - load file from an UBIFS filesystem | |
| Usage: | |
| ubifsload <addr> <filename> [bytes] | |
| - load file 'filename' to address 'addr' | |
| UBIFS not mounted, use ubifs mount to mount volume first! | |
| ubifsload - load file from an UBIFS filesystem | |
| Usage: | |
| ubifsload <addr> <filename> [bytes] | |
| - load file 'filename' to address 'addr' | |
| Ventana > | |
| ########################################################################### | |
| ####### It sat here until I turned the watchdog back on. | |
| ########################################################################### | |
| Ventana > gsc wd enable | |
| GSC Watchdog enabled with timeout=30 seconds | |
| Ventana > | |
| ########################################################################### | |
| ########################################################################### | |
| ########################################################################### | |
| U-Boot SPL 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| Booting from NAND | |
| PMIC: LTC3676 | |
| NAND : 256 MiB | |
| *** Warning - bad CRC, using default environment | |
| U-Boot 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| CPU: Freescale i.MX6DL rev1.2 at 792MHz | |
| CPU: Industrial temperature grade (-40C to 105C) at 54C | |
| Reset cause: POR | |
| I2C: ready | |
| DRAM: 1 GiB | |
| PMIC: LTC3676 | |
| NAND: 256 MiB | |
| MMC: FSL_SDHC: 0 | |
| *** Warning - bad CRC, using default environment | |
| PCI: | |
| 00:01.0 - 16c3:abcd - Bridge device | |
| 01:00.0 - 168c:0032 - Network controller | |
| No panel detected: default to HDMI | |
| Display: HDMI (1024x768) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Gateworks Corporation Copyright 2014 | |
| Model: GW5100-SP325-D | |
| MFGDate: 05-15-2015 | |
| Serial:666445 | |
| GSC: v46 0xd0f9 WDT:enabled WDT_RESET board temp at 44C | |
| RTC: 1161 | |
| DIO0: GPIO1_IO16 (gpio-16) | |
| DIO1: GPIO1_IO19 (gpio-19) | |
| DIO2: GPIO1_IO17 (gpio-17) | |
| DIO3: GPIO1_IO18 (gpio-18) | |
| RS232: enabled | |
| Net: Phy 0 not found | |
| PHY reset timed out | |
| set ethprime to FEC | |
| FEC [PRIME] | |
| Error: FEC address not set. | |
| , usb_ether | |
| Error: usb_ether address not set. | |
| Hit any key to stop autoboot: 0 | |
| Attempting usb boot... | |
| starting USB... | |
| USB0: Port not available. | |
| USB1: USB EHCI 1.00 | |
| scanning bus 1 for devices... 4 USB Device(s) found | |
| scanning usb for storage devices... 1 Storage Device(s) found | |
| scanning usb for ethernet devices... 0 Ethernet Device(s) found | |
| USB device 0: | |
| Device 0: Vendor: Generic Rev: 1.76 Prod: Ultra HS-SD/MMC | |
| Type: Removable Hard Disk | |
| Capacity: 7580.0 MB = 7.4 GB (15523840 x 512) | |
| ... is now current device | |
| 0 bytes read in 98 ms (0 Bytes/s) | |
| ## Executing script at 12000000 | |
| Wrong image format for "source" command | |
| ** File not found boot/uImage ** | |
| Attempting mmc boot... | |
| MMC: no card present | |
| MMC: no card present | |
| ** Bad device mmc 0 ** | |
| MMC: no card present | |
| ** Bad device mmc 0 ** | |
| Attempting sata boot... | |
| ** Bad device size - sata 0 ** | |
| ** Bad device size - sata 0 ** | |
| Attempting flash boot... | |
| UBI: attaching mtd1 to ubi0 | |
| UBI: scanning is finished | |
| UBI: attached mtd1 (name "mtd=2", size 239 MiB) to ubi0 | |
| UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | |
| UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | |
| UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 | |
| UBI: good PEBs: 1912, bad PEBs: 0, corrupted PEBs: 0 | |
| UBI: user volume: 0, internal volumes: 1, max. volumes count: 128 | |
| UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 669125316 | |
| UBI: available PEBs: 1868, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40 | |
| UBIFS not mounted, use ubifs mount to mount volume first! | |
| ubifsload - load file from an UBIFS filesystem | |
| Usage: | |
| ubifsload <addr> <filename> [bytes] | |
| - load file 'filename' to address 'addr' | |
| UBIFS not mounted, use ubifs mount to mount volume first! | |
| ubifsload - load file from an UBIFS filesystem | |
| Usage: | |
| ubifsload <addr> <filename> [bytes] | |
| - load file 'filename' to address 'addr' | |
| Ventana > | |
| U-Boot SPL 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| Booting from NAND | |
| PMIC: LTC3676 | |
| NAND : 256 MiB | |
| *** Warning - bad CRC, using default environment | |
| U-Boot 2015.04-g85edf72 (Nov 30 2015 - 09:12:48) | |
| CPU: Freescale i.MX6DL rev1.2 at 792MHz | |
| CPU: Industrial temperature grade (-40C to 105C) at 54C | |
| Reset cause: POR | |
| I2C: ready | |
| DRAM: 1 GiB | |
| PMIC: LTC3676 | |
| NAND: 256 MiB | |
| MMC: FSL_SDHC: 0 | |
| *** Warning - bad CRC, using default environment | |
| PCI: | |
| 00:01.0 - 16c3:abcd - Bridge device | |
| 01:00.0 - 168c:0032 - Network controller | |
| No panel detected: default to HDMI | |
| Display: HDMI (1024x768) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Gateworks Corporation Copyright 2014 | |
| Model: GW5100-SP325-D | |
| MFGDate: 05-15-2015 | |
| Serial:666445 | |
| GSC: v46 0xd0f9 WDT:enabled WDT_RESET board temp at 44C | |
| RTC: 1194 | |
| DIO0: GPIO1_IO16 (gpio-16) | |
| DIO1: GPIO1_IO19 (gpio-19) | |
| DIO2: GPIO1_IO17 (gpio-17) | |
| DIO3: GPIO1_IO18 (gpio-18) | |
| RS232: enabled | |
| Net: Phy 0 not found | |
| PHY reset timed out | |
| set ethprime to FEC | |
| FEC [PRIME] | |
| Error: FEC address not set. | |
| , usb_ether | |
| Error: usb_ether address not set. | |
| Hit any key to stop autoboot: 2 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment