config for meshtisticd works on orangepi zero 3 with Debian 12

config.yaml

### Many device configs have been moved to /etc/meshtasticd/available.d
### To activate, simply copy or link the appropriate file into /etc/meshtasticd/config.d

### Define your devices here using Broadcom pin numbering
### Uncomment the block that corresponds to your hardware
### Including the "Module:" line!

Lora:
  # Default to auto-detecting the module type
  # This will be overridden by configs from config.d
#  Module: auto

#  # Uncomment to enable Simulation mode, or use --sim
#  Module: sim

#  Module: sx1262  # Waveshare SX1302 LISTEN ONLY AT THIS TIME!
#  CS: 7
#  IRQ: 17
#  Reset: 22

#  Module: RF95  # Elecrow Lora RFM95 IOT https://www.elecrow.com/lora-rfm95-iot-board-for-rpi.html
#  Reset: 22
#  CS: 7
#  IRQ: 25

#  Module: sx1280  # SX1280
#  CS: 21
#  IRQ: 16
#  Busy: 20
#  Reset: 18

### The Radxa Zero 3E/W employs multiple gpio chips.
### Each gpio pin must be unique, but can be assigned to a specific gpio chip and line.
### In case solely a no. is given, the default gpio chip and pin == line will be employed.
###
#  Module: sx1262  # Radxa Zero 3E/W + Ebyte E22-900M30S
#  DIO2_AS_RF_SWITCH: true
#  DIO3_TCXO_VOLTAGE: 1.8
#  CS:             # NSS     PIN_24 -> chip 4, line 22
#    pin: 24
#    gpiochip: 4
#    line: 22
#  SCK:            # SCK     PIN_23 -> chip 4, line 18
#    pin: 23
#    gpiochip: 4
#    line: 18
#  Busy:           # BUSY    PIN_29 -> chip 3!, line 11
#    pin: 29
#    gpiochip: 3
#    line: 11
#  MOSI:           # MOSI    PIN_19 -> chip 4, line 19
#    pin: 19
#    gpiochip: 4
#    line: 19
#  MISO:           # MISO    PIN_21 -> chip 4, line 21
#    pin: 21
#    gpiochip: 4
#    line: 21
#  Reset:          # NRST    PIN_27 -> chip 4, line 10
#    pin: 27
#    gpiochip: 4
#    line: 10
#  IRQ:            # DIO1    PIN_28 -> chip 4, line 11
#    pin: 28
#    gpiochip: 4
#    line: 11
#  RXen:           # RXEN    PIN_22 -> chip 3!, line 17
#    pin: 22
#    gpiochip: 3
#    line: 17
#  TXen: RADIOLIB_NC # TXEN   no PIN, no line, fallback to default gpio chip

  Module: sx1268  # SX1268-based modules, tested with Ebyte E22 400M33S 5V in
#  CS:
#    pin: 24
#    gpiochip: 0
#    line: 233
  SCK:
    pin: 23
    gpiochip: 0
    line: 230
  MOSI:
    pin: 19
    gpiochip: 0
    line: 231
  MISO:
    pin: 21
    gpiochip: 0
    line: 232
  IRQ:
    pin: 7
    gpiochip: 0
    line: 73
  Busy:
    pin: 18
    gpiochip: 0
    line: 78
  Reset:
    pin: 22
    gpiochip: 0
    line: 71
  TXen:
    pin: 15
    gpiochip: 0
    line: 72
  RXen:
    pin: 27
    gpiochip: 0
    line: 65
  DIO2_AS_RF_SWITCH: true
  DIO3_TCXO_VOLTAGE: true

#  DIO3_TCXO_VOLTAGE: true  # the Waveshare Core1262 and others are known to need this setting

#  TXen: x  # TX and RX enable pins
#  RXen: x

  SX126X_MAX_POWER: 8  # Limit the output power to 8 dBm, useful for amped nodes

  spiSpeed: 500000

### Set default/fallback gpio chip to use in /dev/. Defaults to 0.
### Notably the Raspberry Pi 5 puts the GPIO header on gpiochip4
  gpiochip: 0

### Specify the SPI device to use in /dev/. Defaults to spidev0.0
### Some devices, like the pinedio, may require spidev0.1 as a workaround.
  spidev: spidev1.1

### Define GPIO buttons here:

#GPIO:
#  User: 6

### Define GPS

#GPS:
#  SerialPath: /dev/ttyS0

### Specify I2C device, or leave blank for none

#I2C:
#  I2CDevice: /dev/i2c-1

### Set up SPI displays here. Note that I2C displays are generally auto-detected.

#Display:

### Waveshare 1.44inch LCD HAT
#  Panel: ST7735S
#  CS: 8         #Chip Select
#  DC: 25        # Data/Command pin
#  Backlight: 24
#  Width: 128
#  Height: 128
#  Reset: 27
#  OffsetX: 0
#  OffsetY: 0

### Adafruit PiTFT 2.8 TFT+Touchscreen
#  Panel: ILI9341
#  CS: 8
#  DC: 25
#  Width: 240
#  Height: 320
#  Rotate: true

### SHCHV 3.5 RPi TFT+Touchscreen
#  Panel: ILI9486
#  spidev: spidev0.0
#  BusFrequency: 30000000
#  DC: 24
#  Reset: 25
#  Width: 320
#  Height: 480
#  OffsetRotate: 2

### TZT 2.0 Inch TFT Display ST7789V 240RGBx320
#  Panel: ST7789
#  spidev: spidev0.0
#  # CS: 8     # can be freely chosen
#  BusFrequency: 80000000
#  DC: 24      # can be freely chosen
#  Width: 320
#  Height: 240
#  Reset: 25   # can be freely chosen
#  Rotate: true
#  OffsetRotate: 1
#  Invert: true

### You can also specify the spi device for the display to use
# spidev: spidev0.0

#Touchscreen:
### Note, at least for now, the touchscreen must have a CS pin defined, even if you let Linux manage the CS switching.

#  Module: STMPE610 # Option 1 for Adafruit PiTFT 2.8
#  CS: 7
#  IRQ: 24

#  Module: FT5x06 # Option 2 for Adafruit PiTFT 2.8
#  IRQ: 24
#  I2CAddr: 0x38

### You can also specify the spi device for the touchscreen to use
# spidev: spidev0.0


#Input:
### Configure device for direct keyboard input

#  KeyboardDevice: /dev/input/by-id/usb-_Raspberry_Pi_Internal_Keyboard-event-kbd

###

Logging:
  LogLevel: info # debug, info, warn, error
#  TraceFile: /var/log/meshtasticd.json
#  AsciiLogs: true     # default if not specified is !isatty() on stdout

Webserver:
  Port: 9443 # Port for Webserver & Webservices
  RootPath: /usr/share/meshtasticd/web # Root Dir of WebServer
  SSLKey: /etc/meshtasticd/ssl/private_key.pem # Path to SSL Key, generated if not present
  SSLCert: /etc/meshtasticd/ssl/certificate.pem # Path to SSL Certificate, generated if not present


#HostMetrics:
#  ReportInterval: 30 # Interval in minutes between HostMetrics report packets, or 0 for disabled
#  Channel: 0 # channel to send Host Metrics over. Defaults to the primary channel.
#  UserStringCommand: cat /sys/firmware/devicetree/base/serial-number # Command to execute, to send the results as the userString


General:
  MaxNodes: 1000
  MaxMessageQueue: 1000
  ConfigDirectory: /etc/meshtasticd/config.d/
  AvailableDirectory: /etc/meshtasticd/available.d/
#  MACAddress: AA:BB:CC:DD:EE:FF
#  MACAddressSource: eth0