monoprice mini delta starting gcode

stock.gcode

; Monoprice Mini Delta
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
M104 S[first_layer_temperature] T0 ; set extruder temp
M109 S[first_layer_temperature] T0 ; wait for extruder temp
G92 E0 ; reset extrusion distance
G28 ; Start from home position
G1 E-6 F900 ; retract 6mm of filament before starting the bed leveling process
G92 E0 ; reset extrusion distance
G4 S5 ; Pause for 5 seconds to allow time for removing extruded filament
G29 P6 Z0.45 ;If your first layer is too far from the bed then lower the Z number, if it is to close, then raise it.
G1 Z60 ; raise Z 60mm to prepare for priming the nozzle
G1 E20 F300 ; extrude 20mm of filament to help prime the nozzle just prior to the start of the print
G92 E0 ; reset extrusion distance
G4 S10 ; Pause for 10 seconds to allow time for cleaniing the nozzle and build plate if needed
G92 E0
;Put printing message on LCD screen
M117 Printing...

tedder v1.gcode

; Monoprice Mini Delta
M92 X116.5 Y116.5 Z116.5 E97.0 ; set xyz scale
M104 S150 T0 ; set extruder preheat temp
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
M109 S150 T0 ; wait for extruder preheat temp

G92 E0 ; reset extrusion distance
G28 ; Start from home position
; can't retract bc we aren't going up to full extruder temp.
; G1 E-6 F900 ; retract 6mm of filament before starting the bed leveling process
; G92 E0 ; reset extrusion distance

G29 P6 Z0.4 ; bed alignment. If your first layer is too far from the bed then lower the Z number, if it is too close, then raise it.

G1 Z10 ; raise Z 10mm to heat nozzle

M104 S[first_layer_temperature] T0 ; set extruder temp
M109 S[first_layer_temperature] T0 ; wait for extruder temp

G92 E0 ; reset extrusion distance
G1 X-54 Y0 Z0.4 F3000 ; move to arc start
G3 X0 Y-54 I52 Z0.4 E40 F400 ; lay arc stripe 90deg
G92 E0 ; reset extrusion distance
G1 X0 Y-50 Z4 E-2 F3000 ; get off the bed
M109 S[first_layer_temperature] T0 ; wait for extruder temp
G92 E0
G28 ; Start from home position again

;Put printing message on LCD screen
M117 Printing...

Okay, thank you

…

On Sat, Mar 23, 2024 at 12:05 PM tedder ***@***.***> wrote: ***@***.**** commented on this gist. ------------------------------ hey @Ajax157 <https://github.com/Ajax157> you can print a cube, like a 50mm cube, and then measure it. Use the M92 numbers to make it the correct size. You can start without values there and see if it's correct. And you're correct, line 14 is the z-offset. Just plug and chug to find a good enough number :) I'm not sure where the P6 comes from, it's been six years since I thought about this. — Reply to this email directly, view it on GitHub <https://gist.github.com/tedder/487816dc125a8330bbcc945c68703709#gistcomment-4998629> or unsubscribe <https://github.com/notifications/unsubscribe-auth/BGFIM5B2VUL7FBYOW57PUR3YZWY5JBFKMF2HI4TJMJ2XIZLTSKBKK5TBNR2WLJDUOJ2WLJDOMFWWLO3UNBZGKYLEL5YGC4TUNFRWS4DBNZ2F6YLDORUXM2LUPGBKK5TBNR2WLJDHNFZXJJDOMFWWLK3UNBZGKYLEL52HS4DFVRZXKYTKMVRXIX3UPFYGLK2HNFZXIQ3PNVWWK3TUUZ2G64DJMNZZDAVEOR4XAZNEM5UXG5FFOZQWY5LFVA4TCOBSHEYTSN5HORZGSZ3HMVZKMY3SMVQXIZI> . You are receiving this email because you were mentioned. Triage notifications on the go with GitHub Mobile for iOS <https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675> or Android <https://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub> .

Do you know why the z offset doesn't change when I change it?