Created
April 2, 2020 04:10
-
-
Save todbot/d33eb2ff83718079e5df027fb3e4dd03 to your computer and use it in GitHub Desktop.
My attempt at a PrusaSlicer config bundle for Monoprice Select Mini V2. Import with "File" -> "Import..." -> "Import Config Bundle"
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by PrusaSlicer 2.2.0+ on 2020-04-02 at 04:02:32 UTC | |
| [print:0.175mm - Monoprice Mini Select v2] | |
| avoid_crossing_perimeters = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = "Monoprice Mini Select v2" | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0.2 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = stars | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.42 | |
| first_layer_height = 0.175 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 70 | |
| inherits = | |
| interface_shells = 0 | |
| layer_height = 0.175 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 50% | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 80 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 1 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 8 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 110 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = 0 | |
| [filament:Monoprice Mini Select v2 - PLA] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = "Monoprice Mini Select v2" | |
| compatible_printers_condition = | |
| compatible_prints = "0.175mm - Monoprice Mini Select v2" | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 205 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 205 | |
| [printer:Monoprice Mini Select v2] | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 0x0,110x0,110x110,0x110 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| cooling_tube_length = 5 | |
| cooling_tube_retraction = 91.5 | |
| default_filament_profile = "" | |
| default_print_profile = | |
| deretract_speed = 40 | |
| end_gcode = ;M104 S0 ; turn off temperature\n;G28 X0 ; home X axis\n;M84 ; disable motors\n\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nG1 Z1 ; raise nozzle\nG1 X5 ; move X axis close to tower but hopefully far enough to keep the fan from rattling\nG1 Y5 ; move bed forward for easier part removal\nM84 ; disable motors\n\n;G1 X0 Y50 F1000 ; prepare for part removal\n;M84 ; disable motors\n | |
| extra_loading_move = -2 | |
| extruder_colour = #2C3DFF | |
| extruder_offset = 0x0 | |
| gcode_flavor = marlin | |
| high_current_on_filament_swap = 0 | |
| host_type = octoprint | |
| inherits = | |
| layer_gcode = | |
| machine_max_acceleration_e = 10000,5000 | |
| machine_max_acceleration_extruding = 1500,1250 | |
| machine_max_acceleration_retracting = 1500,1250 | |
| machine_max_acceleration_x = 9000,1000 | |
| machine_max_acceleration_y = 9000,1000 | |
| machine_max_acceleration_z = 500,200 | |
| machine_max_feedrate_e = 120,120 | |
| machine_max_feedrate_x = 500,200 | |
| machine_max_feedrate_y = 500,200 | |
| machine_max_feedrate_z = 12,12 | |
| machine_max_jerk_e = 2.5,2.5 | |
| machine_max_jerk_x = 10,10 | |
| machine_max_jerk_y = 10,10 | |
| machine_max_jerk_z = 0.2,0.4 | |
| machine_min_extruding_rate = 0,0 | |
| machine_min_travel_rate = 0,0 | |
| max_layer_height = 0 | |
| max_print_height = 200 | |
| min_layer_height = 0.07 | |
| nozzle_diameter = 0.4 | |
| parking_pos_retraction = 92 | |
| print_host = | |
| printer_model = | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = FFF | |
| printer_variant = | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| remaining_times = 0 | |
| retract_before_travel = 1 | |
| retract_before_wipe = 90% | |
| retract_layer_change = 1 | |
| retract_length = 4.5 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| serial_port = | |
| serial_speed = 250000 | |
| silent_mode = 1 | |
| single_extruder_multi_material = 0 | |
| start_gcode = ;G28 ; home all axes\n;G1 Z5 F5000 ; lift nozzle\nG28 ; home all axes\nM109 S[first_layer_temperature] ; set the extruder temp and wait\nG1 Z0.2 F1200 ; raise nozzle\nG92 E0 ; reset extrusion distance\nG1 X100 Y0 E12 F600 ; wipe\nG92 E0 ; reset extrusion distance | |
| thumbnails = | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| variable_layer_height = 1 | |
| wipe = 1 | |
| z_offset = 0 | |
| [presets] | |
| print = 0.175mm - Monoprice Mini Select v2 | |
| sla_print = | |
| sla_material = | |
| printer = Monoprice Mini Select v2 | |
| filament = Monoprice Mini Select v2 - PLA |
Instead of this, I simply copied Start and End G-code from Cura Machine Settings to Prusaslicer Custom G-code setting and set G-code flavor to Merlin (legacy) and it worked.
So add G191\n before \nG1 Z1?
Not G191, G91, but yes add it before G1 Z1 and it should be fine…
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Wish I had seen @jyockey's comment before using this haha I learned that the hard way as well. The G91 line before the G1 Z1 fixes it, as he said. I would highly recommend modifying this file so that future people don't use it without reading the comments, oops.