Created
November 10, 2019 01:02
-
-
Save tuklusan/53ddb38961beb82d755aae9b730cd25f to your computer and use it in GitHub Desktop.
Install HP-UX 11i on QEMU: Installation Phase - HP 9000/778 Console; see https://supratim-sanyal.blogspot.com/2019/11/hpux-11i-v1-hpux-1111-pa-risc-guest.html
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Script started on Sun Nov 3 01:32:30 2019 | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ telnet localhos r t 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| 1 250 MHz Idle Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux (;0):INSTALL | |
| Boot | |
| : disc(8/0/0/0.2.0;0):INSTALL | |
| telnet> mode character | |
| 9793660 + 1126400 + 702592 start 0x152868 | |
| WARNING: can't enable implementation specific instructions | |
| WARNING: can't enable implementation specific instructions | |
| NOTICE: nfs3_link(): File system was registered at index 4. | |
| System Console is on the Built-In Serial Interface | |
| Swap device table: (start & size given in 512-byte blocks) | |
| entry 0 - auto-configured on root device; ignored - no room | |
| WARNING: no swap device configured, so dump cannot be defaulted to primary swap. | |
| WARNING: No dump devices are configured. Dump is disabled. | |
| Starting the STREAMS daemons-phase 1 | |
| Create STCP device files | |
| Starting the STREAMS daemons-phase 2 | |
| $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:05:38 PST 2000 $ | |
| Memory Information: | |
| physical page size = 4096 bytes, logical page size = 4096 bytes | |
| Physical: 524288 Kbytes, lockable: 369396 Kbytes, available: 443200 Kbytes | |
| ======= 11/02/19 20:34:29 EST HP-UX Installation Initialization. (Sat Nov 02 | |
| 20:34:29 EST 2019) | |
| @(#) Ignite-UX Revision C.6.3.324 | |
| @(#) install/init (opt) $Revision: 10.333 $ | |
| * EISA configuration has completed. Following the completion of a | |
| successful HP-UX installation, please check the "/etc/eisa/config.err" | |
| file for any EISA configuration messages. | |
| * Scanning system for IO devices... | |
| * Querying disk device: 8/0/0/0.0.0 ... | |
| * Querying disk device: 8/0/0/0.1.0 ... | |
| * Setting keyboard language. | |
| .[ci | |
| 7[r[999;999H[6n8i | |
| [?1h[0m[2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C2 | [ H/W [;4mD[metails ][B | |
| +---------------------+----------------+-------------------+[16;24H[ [;7m [;7;4mI[;7mnstall HP-UX [m ][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][16;26H[13;67H[;7m/W [;7;4mD[;7metails[m[16;27H [;4mI[mnstall HP-UX [13;66H[2J[H[BDisk Drives:[B | |
| H/W Path[14CCapacity(Mb) Model[B | |
| 8/0/0/0.0.0[12C8192[11CQEMU_QEMU_HARDDISK[B | |
| 8/0/0/0.1.0[12C8192[11CQEMU_QEMU_HARDDISK[2B | |
| LAN Interfaces:[B | |
| H/W Path Interface Name LAN Address Description[B | |
| 8/0/1/0 lan0[11C525400123456 HP_PCI_10/100Base-TX_Core[2B | |
| CD/DVD-ROM Drives:[B | |
| 8/0/0/0.2.0[12CQEMU_QEMU_CD-ROM[2B | |
| I/O Buses:[B | |
| 8/0/0/0[16CSCSI_C895_Fast_Wide_LVD[2B | |
| Processors:[B | |
| 48[21CProcessor[B | |
| 49[21CProcessor[5B | |
| (Press any key to continue.) | |
| [0K[4A[10;64H[ S[;4mc[man Again ][13;64H[ H/W [;4mD[metails ][16;24H[[6C[;4mI[mnstall HP-UX[7C][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][3A | |
| [2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C2 | [ H[;7m/W [;7;4mD[;7metails[m ][B | |
| +---------------------+----------------+-------------------+[16;24H[[6C[;4mI[mnstall HP-UX[7C | |
| telnet> quit | |
| Connection closed. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # T --------------------------------- | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # ---------------------------------[13Ptelnet localhost 54321script HPUX-INST-QEMU.log[3Ptelnet localhost 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| 1 250 MHz Idle Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux (;0):INSTALL | |
| Boot | |
| : disc(8/0/0/0.2.0;0):INSTALL | |
| telnet> mode character | |
| 9793660 + 1126400 + 702592 start 0x152868 | |
| WARNING: can't enable implementation specific instructions | |
| WARNING: can't enable implementation specific instructions | |
| NOTICE: nfs3_link(): File system was registered at index 4. | |
| System Console is on the Built-In Serial Interface | |
| Swap device table: (start & size given in 512-byte blocks) | |
| entry 0 - auto-configured on root device; ignored - no room | |
| WARNING: no swap device configured, so dump cannot be defaulted to primary swap. | |
| WARNING: No dump devices are configured. Dump is disabled. | |
| Starting the STREAMS daemons-phase 1 | |
| Create STCP device files | |
| Starting the STREAMS daemons-phase 2 | |
| $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:05:38 PST 2000 $ | |
| Memory Information: | |
| physical page size = 4096 bytes, logical page size = 4096 bytes | |
| Physical: 524288 Kbytes, lockable: 369392 Kbytes, available: 443136 Kbytes | |
| ======= 11/02/19 20:46:03 EST HP-UX Installation Initialization. (Sat Nov 02 | |
| 20:46:02 EST 2019) | |
| @(#) Ignite-UX Revision C.6.3.324 | |
| @(#) install/init (opt) $Revision: 10.333 $ | |
| * EISA configuration has completed. Following the completion of a | |
| successful HP-UX installation, please check the "/etc/eisa/config.err" | |
| file for any EISA configuration messages. | |
| * Scanning system for IO devices... | |
| * Querying disk device: 8/0/0/0.0.0 ... | |
| * Querying disk device: 8/0/0/0.1.0 ... | |
| * Setting keyboard language. | |
| .[ci | |
| 7[r[999;999H[6n8i | |
| [?1h[0m[2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C2 | |
| telnet> mode line | |
| ^] | |
| telnet> quit | |
| Connection closed. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # ------------------------------------- | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # -------------------------------------[17Ptelnet localhost 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| 1 250 MHz Idle Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux (;0):INSTALL | |
| Boot | |
| : disc(8/0/0/0.2.0;0):INSTALL | |
| 9793660 + 1126400 + 702592 start 0x152868 | |
| WARNING: can't enable implementation specific instructions | |
| WARNING: can't enable implementation specific instructions | |
| NOTICE: nfs3_link(): File system was registered at index 4. | |
| System Console is on the Built-In Serial Interface | |
| Swap device table: (start & size given in 512-byte blocks) | |
| entry 0 - auto-configured on root device; ignored - no room | |
| WARNING: no swap device configured, so dump cannot be defaulted to primary swap. | |
| WARNING: No dump devices are configured. Dump is disabled. | |
| Starting the STREAMS daemons-phase 1 | |
| Create STCP device files | |
| Starting the STREAMS daemons-phase 2 | |
| $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:05:38 PST 2000 $ | |
| Memory Information: | |
| physical page size = 4096 bytes, logical page size = 4096 bytes | |
| Physical: 524288 Kbytes, lockable: 369400 Kbytes, available: 443188 Kbytes | |
| ======= 11/02/19 20:52:58 EST HP-UX Installation Initialization. (Sat Nov 02 | |
| 20:52:57 EST 2019) | |
| @(#) Ignite-UX Revision C.6.3.324 | |
| @(#) install/init (opt) $Revision: 10.333 $ | |
| * EISA configuration has completed. Following the completion of a | |
| successful HP-UX installation, please check the "/etc/eisa/config.err" | |
| file for any EISA configuration messages. | |
| * Scanning system for IO devices... | |
| * Querying disk device: 8/0/0/0.0.0 ... | |
| * Querying disk device: 8/0/0/0.1.0 ... | |
| * Setting keyboard language. | |
| .[ci | |
| 7[r[999;999H[6n8i | |
| [?1h[0m[2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C2 | [ H/W [;4mD[metails ][B | |
| +---------------------+----------------+-------------------+[16;24H[ [;7m [;7;4mI[;7mnstall HP-UX [m ][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][16;26H [;4mI[mnstall HP-UX [18;27H[;7m [;7;4mR[;7mun a Recovery Shell [m[24D [;4mR[mun a Recovery Shell [20;27H[;7m [;7;4mA[;7mdvanced Options [m[24D [;4mA[mdvanced Options [23;14H[;7mRe[;7;4mb[;7moot [m[8D Re[;4mb[moot [35C[;7;4mH[;7melp [m[6D [;4mH[melp [6D[10;67H[;7;4mc[;7man Again [m[11DS[;4mc[man Again [13;67H[;7m/W [;7;4mD[;7metails[m[11D[2J[H[BDisk Drives:[B | |
| H/W Path[14CCapacity(Mb) Model[B | |
| 8/0/0/0.0.0[12C8192[11CQEMU_QEMU_HARDDISK[B | |
| 8/0/0/0.1.0[12C8192[11CQEMU_QEMU_HARDDISK[2B | |
| LAN Interfaces:[B | |
| H/W Path Interface Name LAN Address Description[B | |
| 8/0/1/0 lan0[11C525400123456 HP_PCI_10/100Base-TX_Core[2B | |
| CD/DVD-ROM Drives:[B | |
| 8/0/0/0.2.0[12CQEMU_QEMU_CD-ROM[2B | |
| I/O Buses:[B | |
| 8/0/0/0[16CSCSI_C895_Fast_Wide_LVD[2B | |
| Processors:[B | |
| 48[21CProcessor[B | |
| 49[21CProcessor[5B | |
| (Press any key to continue.) | |
| [0K[4A[10;64H[ S[;4mc[man Again ][13;64H[ H/W [;4mD[metails ][16;24H[[6C[;4mI[mnstall HP-UX[7C][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][3A | |
| [2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C2 | [ H[;7m/W [;7;4mD[;7metails[m ][B | |
| +---------------------+----------------+-------------------+[16;24H[[6C[;4mI[mnstall HP-UX[7C][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][13;66HH/W [;4mD[metails[16;27H[;7m [;7;4mI[;7mnstall HP-UX [m[24D[2J[H[24C[;7mUser Interface and Media Options[m[3;4HThis screen lets you pick from options that will determine if an[4;4HIgnite-UX server is used, and your user interface preference.[6;2HSource Location Options:[7;4H[ * ] [;4mM[media only installation[8;4H[ ] Media with [;4mN[metwork enabled (allows use of SD depots)[9;4H[ ] [;4mI[mgnite-UX server based installation[11;2HUser Interface Options:[12;4H[ * ] [;4mG[muided Installation (recommended for basic installs)[13;4H[ ] [;4mA[mdvanced Installation (recommended for disk and filesystem management)[14;4H[ ] No [;4mu[mser interface - use all the defaults and go[17;4HHint: If you need to make LVM size changes, or want to set the[18;10Hfinal networking parameters during the install, you will[19;10Hneed to use the Advanced mode (or remote graphical interface).[23;4H[ [;7m [;7;4mO[;7mK [m ][18C[ [;4mC[mancel ][25C[ [;4mH[melp ][71D [;4mO[mK [6D[2J[H[10BConnection closed by foreign host. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # ------------------------------------------ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # ------------------------------------------[22Ptelnet localhost 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| 1 250 MHz Idle Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux (;0):INSTALL | |
| Boot | |
| : disc(8/0/0/0.2.0;0):INSTALL | |
| 9793660 + 1126400 + 702592 start 0x152868 | |
| WARNING: can't enable implementation specific instructions | |
| WARNING: can't enable implementation specific instructions | |
| NOTICE: nfs3_link(): File system was registered at index 4. | |
| System Console is on the Built-In Serial Interface | |
| Swap device table: (start & size given in 512-byte blocks) | |
| entry 0 - auto-configured on root device; ignored - no room | |
| WARNING: no swap device configured, so dump cannot be defaulted to primary swap. | |
| WARNING: No dump devices are configured. Dump is disabled. | |
| Starting the STREAMS daemons-phase 1 | |
| Create STCP device files | |
| Starting the STREAMS daemons-phase 2 | |
| $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:05:38 PST 2000 $ | |
| Memory Information: | |
| physical page size = 4096 bytes, logical page size = 4096 bytes | |
| Physical: 524288 Kbytes, lockable: 369392 Kbytes, available: 443028 Kbytes | |
| ======= 11/02/19 21:53:32 EST HP-UX Installation Initialization. (Sat Nov 02 | |
| 21:53:32 EST 2019) | |
| @(#) Ignite-UX Revision C.6.3.324 | |
| @(#) install/init (opt) $Revision: 10.333 $ | |
| * EISA configuration has completed. Following the completion of a | |
| successful HP-UX installation, please check the "/etc/eisa/config.err" | |
| file for any EISA configuration messages. | |
| * Scanning system for IO devices... | |
| * Querying disk device: 8/0/0/0.0.0 ... | |
| * Querying disk device: 8/0/0/0.1.0 ... | |
| * Setting keyboard language. | |
| .[ci | |
| 7[r[999;999H[6n8i | |
| [?1h[0m[2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to | |
| telnet> quit | |
| Connection closed. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # --------------------------------- | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ # ---------------------------------[13Ptelnet localhost 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux (;0):INSTALL | |
| Boot | |
| : disc(8/0/0/0.2.0;0):INSTALL | |
| telnet> mode character | |
| 9793660 + 1126400 + 702592 start 0x152868 | |
| WARNING: can't enable implementation specific instructions | |
| NOTICE: nfs3_link(): File system was registered at index 4. | |
| System Console is on the Built-In Serial Interface | |
| Swap device table: (start & size given in 512-byte blocks) | |
| entry 0 - auto-configured on root device; ignored - no room | |
| WARNING: no swap device configured, so dump cannot be defaulted to primary swap. | |
| WARNING: No dump devices are configured. Dump is disabled. | |
| Starting the STREAMS daemons-phase 1 | |
| Create STCP device files | |
| $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:05:38 PST 2000 $ | |
| Memory Information: | |
| physical page size = 4096 bytes, logical page size = 4096 bytes | |
| Physical: 524288 Kbytes, lockable: 370464 Kbytes, available: 444120 Kbytes | |
| ======= 11/02/19 21:57:14 EST HP-UX Installation Initialization. (Sat Nov 02 | |
| 21:57:14 EST 2019) | |
| @(#) Ignite-UX Revision C.6.3.324 | |
| @(#) install/init (opt) $Revision: 10.333 $ | |
| * EISA configuration has completed. Following the completion of a | |
| successful HP-UX installation, please check the "/etc/eisa/config.err" | |
| file for any EISA configuration messages. | |
| * Scanning system for IO devices... | |
| * Querying disk device: 8/0/0/0.0.0 ... | |
| * Querying disk device: 8/0/0/0.1.0 ... | |
| * Setting keyboard language. | |
| .[ci | |
| 7[r[999;999H[6n8i | |
| [?1h[0m[2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C1 | [ H/W [;4mD[metails ][B | |
| +---------------------+----------------+-------------------+[16;24H[ [;7m [;7;4mI[;7mnstall HP-UX [m ][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][16;26H [;4mI[mnstall HP-UX [18;27H[;7m [;7;4mR[;7mun a Recovery Shell [m[24D[2A [;7m [;7;4mI[;7mnstall HP-UX [m[18;27H [;4mR[mun a Recovery Shell [16;26H[13;67H[;7m/W [;7;4mD[;7metails[m[16;27H [;4mI[mnstall HP-UX [13;66H[2J[H[BDisk Drives:[B | |
| H/W Path[14CCapacity(Mb) Model[B | |
| 8/0/0/0.0.0[12C8192[11CQEMU_QEMU_HARDDISK[B | |
| 8/0/0/0.1.0[12C8192[11CQEMU_QEMU_HARDDISK[2B | |
| LAN Interfaces:[B | |
| H/W Path Interface Name LAN Address Description[B | |
| 8/0/1/0 lan0[11C525400123456 HP_PCI_10/100Base-TX_Core[2B | |
| CD/DVD-ROM Drives:[B | |
| 8/0/0/0.2.0[12CQEMU_QEMU_CD-ROM[2B | |
| I/O Buses:[B | |
| 8/0/0/0[16CSCSI_C895_Fast_Wide_LVD[2B | |
| Processors:[B | |
| 48[21CProcessor[6B | |
| (Press any key to continue.) | |
| [0K[5A[10;64H[ S[;4mc[man Again ][13;64H[ H/W [;4mD[metails ][16;24H[[6C[;4mI[mnstall HP-UX[7C][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][4A | |
| [2J[H[2;14HWelcome to the HP-UX installation/recovery process![4;3HUse the <tab> key to navigate between fields, and the arrow keys[B | |
| within fields. Use the <return/enter> key to select an item.[B | |
| Use the <return/enter> or <space-bar> to pop-up a choices list. If the[B | |
| menus are not clear, select the "Help" item for more information.[9;3HHardware Summary:[9CSystem Model: 9000/778/B160L[B | |
| +---------------------+----------------+-------------------+ [ S[;4mc[man Again ][B | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[B | |
| | CD/DVDs:[8C1 | Tapes: 0 | Memory: 512Mb |[B | |
| | Graphics Ports: 0 | IO Buses: 1 | CPUs:[8C1 | [ H[;7m/W [;7;4mD[;7metails[m ][B | |
| +---------------------+----------------+-------------------+[16;24H[[6C[;4mI[mnstall HP-UX[7C][18;24H[ [;4mR[mun a Recovery Shell ][20;24H[ [;4mA[mdvanced Options[6C][23;11H[ Re[;4mb[moot ][30C[ [;4mH[melp ][13;66HH/W [;4mD[metails[16;27H[;7m [;7;4mI[;7mnstall HP-UX [m[24D[2J[H[24C[;7mUser Interface and Media Options[m[3;4HThis screen lets you pick from options that will determine if an[4;4HIgnite-UX server is used, and your user interface preference.[6;2HSource Location Options:[7;4H[ * ] [;4mM[media only installation[8;4H[ ] Media with [;4mN[metwork enabled (allows use of SD depots)[9;4H[ ] [;4mI[mgnite-UX server based installation[11;2HUser Interface Options:[12;4H[ * ] [;4mG[muided Installation (recommended for basic installs)[13;4H[ ] [;4mA[mdvanced Installation (recommended for disk and filesystem management)[14;4H[ ] No [;4mu[mser interface - use all the defaults and go[17;4HHint: If you need to make LVM size changes, or want to set the[18;10Hfinal networking parameters during the install, you will[19;10Hneed to use the Advanced mode (or remote graphical interface).[23;4H[ [;7m [;7;4mO[;7mK [m ][18C[ [;4mC[mancel ][25C[ [;4mH[melp ][71D [;4mO[mK [6D[2J[H[10B * Using client directory: /var/opt/ignite/clients/0x525400123456 | |
| [17B[?1l * Checking configuration for consistency... | |
| * Loading configuration user interface, please wait... | |
| [4l[20l[12h[16h[?7l[?42l=[?6l[?25h[?10l(B)0[H[999B[999C[6n [6n[[H[J[?25h[H[J[0;1m l[0;7m [0;1;7m Install HP-UX wizard: Select an overall system configuration [0;7m [0;1mk | |
| x x | |
| x The first step towards installing HP-UX is to choose an overall system x | |
| x configuration. The configurations which you see listed below are x | |
| x general in nature. They include all of the detail required to build x | |
| x your system and specify things like: operating system, root disk, x | |
| x desktop environment, file system layout, languages, etc. You will x | |
| x have the opportunity on the subsequent steps to further refine your x | |
| x overall configuration. Please select a configuration and select x | |
| x <Next> to continue to the next step. x | |
| x x | |
| x x | |
| x Configurations: [ [0;1;7m [0;1m [0;1;7m->[0;1m] [ [0;1;4mD[0;1mescription... ] x | |
| x x | |
| x x | |
| x Note: If at any point, you find that you need to specify detailed x | |
| x information which this interface does not support, you may <Cancel> x | |
| x from this task wizard and elect to use the Advanced interface instead. x | |
| x x | |
| x x | |
| xqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqx | |
| x [ [0;1;4mN[0;1mext > ] [ [0;1;4mC[0;1mancel ] [ [0;1;4mH[0;1melp ] x | |
| mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj [57D[10A[18D[9BWorking...[17C [C [C [C [6C [C [C [6C [2C [2C [51D[9A[C[0;1;7mHP-UX B.11.11 Default[40D[9B[0;1m [17C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][51D[9A[CHP-UX B.11.11 Default[4C->[3C[0;1;7m [0;1;4;7mD[0;1;7mescription... [17D[0;1m [0;1;4mD[0;1mescription... [38D[9B[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[31D[19A[0;1m [C [C [C [C [C [C [C [C [C [C [C [70D | |
| [2C [C [C [C [C [C [C [C [65D | |
| In this[Cstep, you will choose the type of [Cnvironment you would l[Cke[68D | |
| t[C use on your system. [CT[2Cs wi[Cl provide [Che basic pers[Cnality of[66D | |
| your system. You can further customize your system[Cby choosing [66D | |
| additional s[Cfware on the "Select Additional[CS[Cftware" scree[C.[C [67D | |
| Software selections that are part of the e[Cv[Cronment will[Cb[C [64D | |
| automatically marked for i[Cstall. [35D | |
| Environments: [[C[0;1;7m [C[0;1m [C [C [4C[0;1;7m->[2C[0;1m [C [2C [70D | |
| [C [C [C [C [C [C [C [C [C [C [C [C [65D | |
| [C [C [C [C [C [C [C [C [C [67D | |
| [C [C [C [C [C [C [C [C [C [C [C [67D[4BWorking...[17C [6C [C [C [6C [2C [2C [53D[9A[C[0;1;7mHP-UX 11i Base OS-32bit[8C[0;1m(HP-UX[CB.11.11)[63D[9B [17C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][53D[9A[13D[12A[0;7m [0;1;7m Install[CHP-UX wizard: Select a system [Cnvironment [0;7m [50D[21B[0;1m[[C<[C[0;1;4mB[0;1mack[C][13;23H[CHP-UX 11i Base OS-32bit[4C->[30D[9B[0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[3C[17A[0;1mdisk[Cwhich will house your root file[70D | |
| system. The di[Ck[C on your [Cystem[Chave b[Cen [Cxamined and some initial[69D | |
| calculations[Chave[Cbeen done to de[Cermine a [Cecomm[Cnded[Cdisk. If[Cyou[67D | |
| re unsure[Cof [Chat[Cto[Cc[Coose, keep the def[Cult selection. You[Cmay[66D | |
| then safely proceed[2Co [Che next step. Otherwise, make your choice[66D | |
| from the fo[Clowing selector. [32D | |
| [[0;1;7m Root Disk... [0;1m] [0;1;4m [0;1m [63D[9BWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [66D[9A[16C[0;1;4mQEMU_QEMU_HARDDISK,[C8/0/0/0.0.0,[C8192[CMB[59D[9B[0;1m [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][66D[9A[6C[12A[0;7m [0;1;7m Install HP-UX wizard: Select a root d[Csk [0;7m [57D[12B[0;1m Root Disk... [2C[22;23H[0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[8D[17A[0;1mspecify the amount of[Cd[Csk[Cspac[5C wish to [70D | |
| re[Cerve[Cfor root [Cwap. Again, some intial calculations have been done[70D | |
| for you. Based on the[Camoun[C of phys[Ccal memory i[C your [Cystem and [68D | |
| th[2Csize of your root[Cdisk, a[Cr[Ccommended va[Cue has bee[C set for [Cou[68D | |
| below. If you ar[C unsure of what you[Cneed, keep the defa[Clt [66D | |
| selec[Cion. Y[Cu may th[Cn safely[Cproceed[Cto[Cthe[Cnext[Cstep.[51D | |
| [0;1;7m Root Swap (MB)... [0;1m] [0;1;4m [0;1m Physical Memory (RAM) = [C0[CMB[64D[9BWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [66D[9A[21C[0;1;4m1024[32C[0;1m512 MB[66D[9B [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][66D[9A[C[12A[0;1;7m Install HP-UX wizard: Specify th[C amount [Cf root swap space [62D[12B[0;1m Root Swap (MB)... [2C[22;23H[0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[31D[17A[0;1mNow that you have[Cmade[Cyour roo[C sw[Cp selection, you n[Ced to choose[67D | |
| which type of file system you would[Clike to use. The current choice [70D | |
| displayed[Cin the selector is recommended.[C If you are [Cnsure of[Cwhat[67D | |
| o choose, keep the default[Csel[2Ction. You may[Cthen safely pr[Cceed to[70D | |
| the next step.[C [C [C [C [C [C [C [C [C [60D | |
| [2C [C [C [C [C [C [C [C [C [56D | |
| File[CSystem:[5C[[C[0;1;7m [39C->[0;1m][58D | |
| [C [C [C [C [C [4C [C [C [C [2C [C [66D[9BWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [53D[10A[C[0;1;7mLogical Volume Manager (LVM) with VxFS[55D[10B[0;1m [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][53D[10A[12D[11A[0;7m [0;1;7m Install[CHP-UX wizard: Select a file system[Ctype[C[0;7m [49D[11B[C[0;1mLogical Volume Manager (LVM) with VxFS[2C->[43D[10B[0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[11D[10ALogical Volume Manager (LVM) with VxFS[2C->[59D[10B[0;1mWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [53D[10A[16D[10B [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][53D[10A[19D[8APlease[Cspecify[Chow[Cmany[Cdisks[Cyou[Cwant[Cplaced[Cinto[Cthe[Croot[59D | |
| disk/volume group[Can[C whethe[C [Cr[Cnot you would like th[C [Cisks t[C b[66D | |
| striped. [C [C [C [C [C [C [C [C [2C [C [C [68D | |
| [C [C [C [C [C [2C [C [C [C [C [C [68D | |
| If[Cyour syst[Cm has many disk[C (more than four),[Cit is recommended that[70D | |
| you[Cput no more[Cthan[Cfour[Cdisks[Cin[Cthe[Croot[Cgroup.[2CThis[Creduces[Cthe[68D | |
| chances[Cof[Ca[Cdisk[Cfailure[Cin[Cthe[Croot[Cgroup.[44D | |
| Striping [Cypically increases overall system performance by[Cspreading[68D | |
| the[Cfile[Csystem[Cload[Cacross[Cmultiple[Cdrives.[2C(Note:[CThe[Csystem[Cmust[68D | |
| have[Cmore[Cthan[Cone[Cdisk[Cto[Cenable[Cstriping.)[44D | |
| The[Cnumber[Cof[Cavailable[Cdisks[Cis:[33D | |
| Number[Cof[CDisks[Cin[CRoot[CGroup:[2C[0;1;4m [3C[0;1mUse[CStriping:[2C[[CNO[3C->][60D | |
| Working...[5C [C [C [C [2C [C [C [C [6C [C [C [6C [2C [2C [40D[3A[16;38H2 | |
| [0;1;4m1[29D | |
| [0;1m [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][40D[3A[25D[18A[0;1;7m Install HP-UX[Cwizard: Specify roo[2Cdisk/volume grou[C disks [35D[18B[0;1;4m2[45C[0;1m [81D[22C[0;1;7mNO[3C->[8D[51D | |
| [0;1mWorking...[5C [C [C [C [2C [C [C [C [6C [C [C [6C [2C [2C [18D[3A[51D | |
| [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][18D[3A[2Alqqqqqk[7D | |
| x[CYES[Cx[7D | |
| x[0;1;7m NO [0;1mx>[8D | |
| mqqqqqj[19;60H[18;59H[0;1;7m YES [5D | |
| [0;1m NO [18;60H[17;58H [7D | |
| [7D | |
| [0;1;7mYES[2C->[8D | |
| [0;1m [19;58H[51D | |
| Working...[5C [C [C [C [2C [C [C [C [6C [C [C [6C [2C [2C [18D[3A[51D | |
| [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][18D[3A[CYES[2C->[43D | |
| [0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[28D[0;1mWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [40D[3A[29D | |
| [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][40D[3A[32D[15AIn this step, you have the opportunity[Cto s[Clect the language[C(or[65D | |
| languages) which you would like to install on your system. Go ahead[68D | |
| and browse[Cthe[Cavailable[Clanguages[Cmaking[Cthe[Cdesired[Cselections.[65D | |
| Once[Cyou[Care[Csatisfied[Cwith[Cyour[Cselections,[Cyou[Cmay[Cmove[Cto[Cthe[Cnext[69D | |
| step. [C [C [C [C [C [C [C [C [C [C [C [70D | |
| [C [C [C [C [C [C [C [C [C [C [2C [C [C [68D | |
| Marked[C? Language [C [C [C [C [40D | |
| lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk[38D | |
| x [C [C [C [C[0;1;7m^[0;1m [C [C [C [68D | |
| [Cx [C [C [C [C [C[0;1;7m [0;1m [2C [C [C [C [68D | |
| x [C [C [C [C [C [C [0;1;7m [0;1m [40D | |
| x[32C[0;1;7mv[38D | |
| [0;1m [Cmqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj[34D | |
| [[CDefault[CLanguage:...[C][C[0;1;4m [46D | |
| [0;1m [C [C [C [C [C [2C [3C [C [2C [C [2C [60D | |
| Working...[5C [C [C [C [2C [C [C [C [6C [C [C [6C [2C [2C [66D[10ANo[8CFrench[16D | |
| No[8CGerman[16D | |
| Yes[7CGlobal[15C[0;7m [32D | |
| [0;1mNo[8CItalian[6C | |
| [0;1;4mASK_AT_FIRST_BOOT[C[0;1mASK_AT_FIRST_BOOT[61D[4B [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][66D[10A[C[11A[0;7m [C[0;1;7mInstall HP-UX[Cwizard:[CSelect a lang[Cage(s) [0;7m [61D[11B[18;9H[0;1;7m Default Language:... [22D[0;1m Default Language:... [2C[10D[4B[0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[28D[0;1mWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [66D[10A[22;7H [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][66D[10A[4;22Hm[Cy sel[Cct any additional sof[Cwar[2Cwhich you would[67D | |
| ike loaded onto[4Cr system. This list includes packages[Cwhich are[68D | |
| not[Cinstalled by def[Cu[Ct[Cbut, may be useful or necessary for your[65D | |
| system's[Cintended us[C.[C Go ahead[Cand browse the list, [Cnce you are [68D | |
| atisfied[Cwith[Cyour[Cselections,[Cyou[Cmay[Cmove[Con[Cto[Cthe[Cnext[Cstep.[59D | |
| [C [2C [22D | |
| Category Marked ? Product[2CDescription[52D | |
| lqqqqqqqqqqqqqqqqqk lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk[74D | |
| x[C[0;1;7m [0;1m [0;1;7m^[0;1m x [15C [35C[0;1;7m^[74D | |
| [0;1mx[3C [C [7C [0;1;7m [0;1m x [15C [35C[0;1;7m [74D | |
| [0;1mx[3C [C [8C [0;1;7m [0;1m x [14C [35C[0;1;7m [74D | |
| [0;1mx[3C [0;1;7mv[0;1m x [35C[0;1;7mv[74D | |
| [0;1mmqqqqqqqqqqqqqqqqqj[Cmqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj[70D | |
| [C [C [C [C [C [61D[4BWorking...[5C [C [C [C [2C [C [C [C [6C [C [C [6C [2C [2C [70D[9A[11;45H Description[58D | |
| [0;1;7mAll[17C[0;1mNo[8C100BaseT-00[6CEISA[C100BaseT;Supptd[CHW[70D | |
| OrderedApps[9CNo[8C100BaseT-01[6CHP-PB[C100BaseT;Supptd[CH[70D | |
| HPUXAdditions[7CNo[8CATM-00[11CPCI[CATM;Supptd[CHW=A5483[C[0;7m [72D | |
| [0;1mUncategorized[7CNo[8CATM-01[11CHSC[CATM;Supptd[CHW=J2468[51D | |
| [0;1;7m< [0;7m [0;1;7m>[71D[4A[C[9B[0;1m [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][50D[9A[10D[12A[0;1;7m Install HP-UX wizard: Select Additio[Cal Software [40D[12B[22;23H < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[31D[18A[0;1mThere are two[Csteps invo[Cved[Ci[C the pre-install checks. T[Ce first is[68D | |
| to identify[Cwhich disk[C will be overwri[Cte[C d[Cring the in[Ctallation [68D | |
| proces[C. If you[Cs[Ce a disk in the list be[Cow whi[Ch you DO NOT want[Cto[70D | |
| include in [Che installati[Cn, please back up[2Co the root disk selection[69D | |
| tep and choose anoth[Cr disk. Otherwise, you may conti[Cue to the[Cnext[70D | |
| step. | |
| Addr[2CDisk[CSize(MB) Description[10C [60D | |
| l[12Cqqq[47Ck [74D | |
| [C x [C [C [C [8C [6C [C [0;1;7m^[C[0;1m [C [74D | |
| [C x [5C [C [C [8C [6C [C [0;7m [0;1m [C [C [74D | |
| [C x [3C [C [C [8C [11C [C [C [0;1;7mv[0;1m [C [74D | |
| [C mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj [C [74D | |
| [C [71D[5BWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [65D[9A[11;17H [C Disk Size(MB) Description[39D | |
| 8/0/0/0.1.0[2C8192[CMB[8CQEMU_QEMU_HARDDISK[46D | |
| 8/0/0/0.0.0[2C8192[CMB[8CQEMU_QEMU_HARDDISK[50D[8B [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][65D[9A[4C[12A[0;1;7m Instal[C HP-UX wizard: Pr[C-install d[Csk inf[Crmation [56D[12B[22;23H < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[31D[19A[0;1mThe[Csecond[Cstep[Cin[Cthe[Cpre-install[Ccheck[Cprocess[Cis[Cto[Creview[Cany[65D | |
| errors or[Cwarnings.[C The warn[2Cgs are simply informational.[C If [Chere[69D | |
| are any errors, they will need t[C be [Cesolve[C before the installation[69D | |
| can continue. If you are unsure of how[Cto resolve the errors,[Cyou may[70D | |
| want to[Cconsult your [Cocal syst[Cm administra[2Cr for addit[Conal h[Clp. [70D | |
| [C [C [C [C [2C [C [C [C [C [C [C [70D | |
| lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk[69D | |
| x[67C[0;1;7m^[69D | |
| [0;1mx[4C [9C [C [2C [24C[0;1;7m [69D | |
| [0;1mx[2C [C[0;1;7m [69D | |
| [0;1mx[2C [C [2C [C [8C [15C [C[0;1;7m [69D | |
| [0;1mx[2C [C [2C [C [8C [15C [C[0;1;7m [69D | |
| [0;1mx[2C [62C [C[0;1;7m [69D | |
| [0;1mx[2C [C[0;1;7mv[69D | |
| [0;1mmqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj[68D[5BWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [68D[12A[22;7H [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][68D[12A[1;50H[0;1;7mcheck information [60D[9B[22;23H < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[0;1m [0;1;4mN[0;1mext > [8D[0;1;7m [0;1;4;7mN[0;1;7mext > [8D[28D[0;1mWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [68D[12A[22;7H [5C[[C<[C[0;1;4mB[0;1mack[C][2C[[C[0;1;4mN[0;1mext[C>[C][6C[[C[0;1;4mC[0;1mancel[C][6C[[2C[0;1;4mH[0;1melp[2C][68D[12A[1;15H[0;7m [0;1;7m Install HP-UX wizard: System Summary [0;7m [64D | |
| [0;1m [C [C [C [C [C [C [C [C [C [C [C [65D | |
| [C [C [2C [C [C [C [C [2C [C [69D | |
| Congratulations, you[Chave[Csuccessfully defined you[C system. P[Ce[Cse [69D | |
| use[Cthe "Show[CSummary" button to[Cview a[Csummary of[Chow[Cyour [Cystem[C [69D | |
| ill[Cbe[4Cfigured. [CIf you see any problems, or wish to change any of[70D | |
| your[Cselections,[Cfeel[Cfree[Cto[Cback[Cup[Cto[Cthe[Cappropriate[Cstep[Cand[Cmake[70D | |
| the needed changes. [69D | |
| [67C [69D | |
| [67C [69D | |
| [17C[[0;1;7m Show [0;1;4;7mS[0;1;7mummary... [0;1m][30C [69D | |
| [67C [69D | |
| [67C [71D | |
| Otherwise,[Cselect[C<Finish>[Cto[Cbegin[Cinstalling[Cyour[Csystem![11C [69D | |
| [67C [69D | |
| [39D[5B[0;1;4mF[0;1minish[17D[10A Show [0;1;4mS[0;1mummary... [18D[0;1;7m Show [0;1;4;7mS[0;1;7mummary... [18D[11A[0;7m [0;1;7m Summary View [0;7m [56D | |
| [0;1mlqqqqqqqqqqqqqqqqqklqqqqqqqqqqqqqqqqqqqqk[41D | |
| x[CGeneral[CSummary[Cxx[CHardware[CInventory[Cx[41D | |
| x [C \qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk[75D | |
| x [C [C [C [C [C [C [C [C [C [C [C [C [8Cx[75D | |
| x [CProduct Description [C [C [C [C [C [C [C [C [C [4Cx[75D | |
| x lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk [4Cx[75D | |
| x x [C [47C[0;1;7m^[7C[0;1mx[75D | |
| x[2Cx[62C[0;7m [7C[0;1mx[75D | |
| x[2Cx[62C[0;1;7mv[7C[0;1mx[75D | |
| x[2Cmqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj[7Cx[75D | |
| x[73Cx[75D | |
| x[4CGrp[CName[2CUsage[3CSize(MB)[2C%[CUsed[2CMount[CDir[24Cx[75D | |
| x lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk[7Cx[75D | |
| x[2Cx[62C[0;1;7m^[7C[0;1mx[75D | |
| x[2Cx[62C[0;1;7m [7C[0;1mx[75D | |
| x[2Cx[62C[0;1;7m [7C[0;1mx[75D | |
| x[2Cx[62C[0;1;7mv[7C[0;1mx[75D | |
| x[2Cmqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj[7Cx[76D | |
| m[73Cj[76D | |
| qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq[77D | |
| x [ [0;1;4mO[0;1mK ] [ [0;1;4mH[0;1melp ] x | |
| mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj [76D[20A[23;4H [2CWorking...[51C [2C [2C [72D[19A[34C | |
| Operating[CSystem:[CHP-UX[CB.11.11[53D | |
| Description[28D | |
| B6848BA[10CXimian[CGNOME[C1.4[CGTK+[CLibraries[Cfor[CHP-UX[58D | |
| B8465BA[10CHP[CWBEM[CServices[Cfor[CHP-UX[43D | |
| B9073BA[10CHP-UX[CiCOD[C(Instant[CCapacity)[47D | |
| [0;1;7m< [0;7m [0;1;7m>[61D[4B[0;1mvg00[6CHFS[5C300[7C7[7C/stand[42D | |
| vg00[6CSWAP+D[2C1024[6C0[7Cprimary[43D | |
| vg00[6CVxFS[4C200[7C42[6C/[24C[0;7m [62D | |
| [0;1mvg00[6CVxFS[4C200[7C0[7C/tmp[45D[4B[[2C [0;1;4mO[0;1mK ] [51C[[2C[0;1;4mH[0;1melp[2C][72D[19A[19C[16D[5B | |
| [C[2A8465[12CHP WBEM Services[Cfor HP-UX [C [C [57D | |
| 9073[14C-UX iCOD (Instant Capacity)[44D | |
| 788A[11CJava2[C1.3 SDK for HP-UX [46D[C[2A9073[14C-UX iCOD (Instant Capacity)[44D | |
| 788A[11CJava2[C1.3 SDK for HP-UX [42D | |
| 9[22CRTE[30D[9;11H788A[11CJava2[C1.3 SDK for HP-UX [42D | |
| 9[22CRTE[29D | |
| UNDLE11i[8CRequired Patch Bundle for[CHP-UX[C11i,[CJune[C2[60D[9;13H9[22CRTE[29D | |
| UNDLE11i[8CRequired Patch Bundle for[CHP-UX[C11i,[CJune[C2[59D | |
| ase-VXVM[8CBase VERITAS Vol[Cme Manager Bundle 3.5 for [60D[C[2AUNDLE11i[8CRequired Patch Bundle for[CHP-UX[C11i,[CJune[C2[59D | |
| ase-VXVM[8CBase VERITAS Vol[Cme Manager Bundle 3.5 for [60D | |
| FDDI[C00 [8CPCI FDDI;Supptd HW=A3739A/A3739B;SW=J3626AA[60D[C[2Aase-VXVM[8CBase VERITAS Vol[Cme Manager Bundle 3.5 for [60D | |
| FDDI[C00 [8CPCI FDDI;Supptd HW=A3739A/A3739B;SW=J3626AA[59D | |
| EATURE11-11[5CFeature Enablement Patches for HP-UX 11i, S[60D[2AFDDI[C00 [8CPCI FDDI;Supptd HW=A3739A/A3739B;SW=J3626AA[59D | |
| EATURE11-11[5CFeature Enablement Patches for HP-UX 11i, S[59D | |
| ibrChanl[C00[5CPCI/HSC[CFibreCha[Cnel;Supptd HW=A6684A,A6685[60D[C[2AEATURE11-11[5CFeature Enablement Patches for HP-UX 11i, S[59D | |
| ibrChanl[C00[5CPCI/HSC[CFibreCha[Cnel;Supptd HW=A6684A,A6685[60D | |
| General Patches[2CMark to[Cload all patches, unmark for just c[60D[C[2AibrChanl[C00[5CPCI/HSC[CFibreCha[Cnel;Supptd HW=A6684A,A6685[60D | |
| General Patches[2CMark to[Cload all patches, unmark for just c[59D | |
| igEther-00 [2CPCI/HSC[CGigEther;Supptd HW=A4926A/A4929A/A4[60D[2AGeneral Patches[2CMark to[Cload all patches, unmark for just c[59D | |
| igEther-00 [2CPCI/HSC[CGigEther;Supptd HW=A4926A/A4929A/A4[59D | |
| lobal [6CGlobal CDE [Cnvi[Conmen[C [C [60D[C[2AigEther-00 [2CPCI/HSC[CGigEther;Supptd HW=A4926A/A4929A/A4[59D | |
| lobal [6CGlobal CDE [Cnvi[Conmen[C [C [60D | |
| HPUXBase32[7CHP-UX 32-bit Base OS [39D[C[2Alobal [6CGlobal CDE [Cnvi[Conmen[C [C [60D | |
| HPUXBase32[7CHP-UX 32-bit Base OS [31D | |
| Aux[12CBase OS Auxiliary[40D[2AHPUXBase32[7CHP-UX 32-bit Base OS [31D | |
| Aux[12CBase OS Auxiliary[39D | |
| WEnabl[C11i[7Cardware Enablement Patches[Cfor[CHP-UX[C11i[Cv[60D[9;17HAux[12CBase OS Auxiliary[39D | |
| WEnabl[C11i[7Cardware Enablement Patches[Cfor[CHP-UX[C11i[Cv[60D | |
| IS[CEPlatform[5CISEE Platform [C [C [C [C [C [60D[C[2AWEnabl[C11i[7Cardware Enablement Patches[Cfor[CHP-UX[C11i[Cv[60D | |
| IS[CEPlatform[5CISEE Platform [C [C [C [C [C [60D | |
| J4269AA [5CLDAP-UX Integration[36D[2AIS[CEPlatform[5CISEE Platform [C [C [C [C [C [60D | |
| J4269AA [5CLDAP-UX Integration[35D | |
| ava15JDK[8CJava 1.5 JDK for HP-UX[39D[2AJ4269AA [5CLDAP-UX Integration[35D | |
| ava15JDK[8CJava 1.5 JDK for HP-UX[30D | |
| add[18C-AA[Caddon[Cfor[CHP-UX[49D[C[2Aava15JDK[8CJava 1.5 JDK for HP-UX[30D | |
| add[18C-AA[Caddon[Cfor[CHP-UX[42D | |
| RE [15CRE[Cfor[CHP-UX[C [C [49D[9;18Hadd[18C-AA[Caddon[Cfor[CHP-UX[42D | |
| RE [15CRE[Cfor[CHP-UX[C [C [40D | |
| add[18C-AA[Caddon[Cfor[CHP-UX[49D[9;16HRE [15CRE[Cfor[CHP-UX[C [C [40D | |
| add[18C-AA[Caddon[Cfor[CHP-UX[49D | |
| MOZILLA [5CMozilla 1.78[Cfor[CHP-UX[C [C [49D[9;18Hadd[18C-AA[Caddon[Cfor[CHP-UX[49D | |
| MOZILLA [5CMozilla 1.78[Cfor[CHP-UX[C [C [42D | |
| src[20CS[Curce distribution[49D[2AMOZILLA [5CMozilla 1.78[Cfor[CHP-UX[C [C [42D | |
| src[20CS[Curce distribution[49D | |
| NPar [7CnPartition Provider[C- HP-UX [49D[9;16Hsrc[20CS[Curce distribution[49D | |
| NPar [7CnPartition Provider[C- HP-UX [45D | |
| Cmds[9CEnhanced NPa[Ctition[CCommands[45D[2ANPar [7CnPartition Provider[C- HP-UX [45D | |
| Cmds[9CEnhanced NPa[Ctition[CCommands[45D | |
| OE91BaseOS32[5CHP-UX 11i B[Cse OS-32bit [45D[9;13HCmds[9CEnhanced NPa[Ctition[CCommands[45D | |
| OE91BaseOS32[5CHP-UX 11i B[Cse OS-32bit [44D | |
| nlineDiag [7CUX 1[C.11 Support Tools[CBundle,[CSep[C2005[58D[2AOE91BaseOS32[5CHP-UX 11i B[Cse OS-32bit [44D | |
| nlineDiag [7CUX 1[C.11 Support Tools[CBundle,[CSep[C2005[57D | |
| penSSL [7CSecure Network Communicatio[Cs Protocol [58D[C[2AnlineDiag [7CUX 1[C.11 Support Tools[CBundle,[CSep[C2005[57D | |
| penSSL [7CSecure Network Communicatio[Cs Protocol [58D | |
| ParMgr [10CPartition Manager - HP-UX [C [55D[C[2ApenSSL [7CSecure Network Communicatio[Cs Protocol [58D | |
| ParMgr [10CPartition Manager - HP-UX [C [55D | |
| Sys[2CmtWeb[7CHP-UX Web[CB[Csed System Management[CUser[CInte[60D[2AParMgr [10CPartition Manager - HP-UX [C [55D | |
| Sys[2CmtWeb[7CHP-UX Web[CB[Csed System Management[CUser[CInte[60D | |
| T1455AA [7CJava2[C1.3[CMozilla Plugin for HP-UX [C [60D[2ASys[2CmtWeb[7CHP-UX Web[CB[Csed System Management[CUser[CInte[60D | |
| T1455AA [7CJava2[C1.3[CMozilla Plugin for HP-UX [C [56D | |
| 6[20C4[CSDK for[CHP-UX [C [C [51D[2AT1455AA [7CJava2[C1.3[CMozilla Plugin for HP-UX [C [56D | |
| 6[20C4[CSDK for[CHP-UX [C [C [44D | |
| addon[19C-AA[Caddon[Cfor[CHP-UX[50D[9;13H6[20C4[CSDK for[CHP-UX [C [C [44D | |
| addon[19C-AA[Caddon[Cfor[CHP-UX[46D | |
| 7[2C [15CRTE[Cfor[CHP-UX[C [C [50D[9;16Haddon[19C-AA[Caddon[Cfor[CHP-UX[46D | |
| 7[2C [15CRTE[Cfor[CHP-UX[C [C [43D | |
| addon[19C-AA[Caddon[Cfor[CHP-UX[50D[9;13H7[2C [15CRTE[Cfor[CHP-UX[C [C [43D | |
| addon[19C-AA[Caddon[Cfor[CHP-UX[46D | |
| 8[2C [15CNetscape Plugin for HP-UX[52D[9;16Haddon[19C-AA[Caddon[Cfor[CHP-UX[46D | |
| 8[2C [15CNetscape Plugin for HP-UX[49D | |
| 71[12CHP-UX[CSecur[C Shell[C [C [C [52D[9;13H8[2C [15CNetscape Plugin for HP-UX[49D | |
| 71[12CHP-UX[CSecur[C Shell[C [C [C [51D | |
| 2743[14C Global Workload[CManager[CAgent[49D[9;12H71[12CHP-UX[CSecur[C Shell[C [C [C [51D | |
| 2743[14C Global Workload[CManager[CAgent[49D | |
| hpuxws[Cpache[7C-UX Apache-base[2CWeb S[2Cver [49D[C[2A2743[14C Global Workload[CManager[CAgent[49D | |
| hpuxws[Cpache[7C-UX Apache-base[2CWeb S[2Cver [43D | |
| Tom[Cat[11CTom[Cat[7CS[Crvl[Ct Engine[50D[2Ahpuxws[Cpache[7C-UX Apache-base[2CWeb S[2Cver [43D | |
| Tom[Cat[11CTom[Cat[7CS[Crvl[Ct Engine[44D | |
| Webmin[11CWebmin[7CAdmin [C [50D[9;15HTom[Cat[11CTom[Cat[7CS[Crvl[Ct Engine[44D | |
| Webmin[11CWebmin[7CAdmin [C [44D | |
| Xml [11CXML Web Server Tools[43D[9;15HWebmin[11CWebmin[7CAdmin [C [44D | |
| Xml [11CXML Web Server Tools[43D | |
| perl [8CPerl Programming Language [43D[9;15HXml [11CXML Web Server Tools[43D | |
| perl [8CPerl Programming Language [43D | |
| vparprovider[5CvPar[4Cvider - HP-UX [42D[5B | |
| [16;19HSWAP+D[2C1[C24[6C0[7Cprimary[33D | |
| VxFS [2C2[C0 [6C42[6C/ [15D | |
| 0 [7Ctmp[21D | |
| 4 [16Chome[41D[16;19HVxFS [2C2[C0 [6C42[6C/ [15D | |
| 0 [7Ctmp[21D | |
| 4 [16Chome[21D | |
| 32[6C81[7Copt [41D[16;37H0 [7Ctmp[21D | |
| 4 [16Chome[21D | |
| 32[6C81[7Copt [22D | |
| 2[9C0[7Cusr[40D[16;28H4 [16Chome[21D | |
| 32[6C81[7Copt [20C[0;7m [43D | |
| [0;1m2[9C0[7Cusr[21C[0;1;7m [44D | |
| [0;1m1528[6C15[7Cva[39D[23;5H[0;1;7m [0;1;4;7mO[0;1;7mK [8D[0;1m [0;1;4mO[0;1mK [56C[0;1;7m [0;1;4;7mH[0;1;7melp [8D[0;1m [0;1;4mH[0;1melp [71D[19A[19C[21D | |
| lqqqqqqqqqqqqqqqqqq/ \[38D | |
| lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk[69D | |
| x[C Hardware[CSummary: System[CModel:[C9000/778/B160L[10C[0;1;7m^[69D | |
| [0;1mx +---------------------+----------------+-------------------+[4C[0;1;7m [67D | |
| [0;1m | Disks:[C2[2C([C16.0GB) | [CFloppies: 0 | LAN[Ccards:[3C1[4C|[4C[0;1;7m [67D | |
| [0;1m | CD/DVDs:[5C 1[C | Tapes:[C 0 |[CMemory:[5C512Mb[C|[4C[0;1;7m [67D | |
| [0;1m | G[Caphics[CPorts: 0[C | IO Buses: 1[3C|[CCPUs:[8C1[4C|[4C[0;1;7m [69D | |
| [0;1mx +---------------------+----------------+-------------------+[4C[0;7m [69D | |
| [0;1mx[67C[0;7m [69D | |
| [0;1mx[CDisk Drives: [3C [2C [C [2C [C [21C[0;7m [69D | |
| [0;1mx H/W Path Capacity(Mb) Model [4C[0;7m [67D | |
| [0;1m 8/0/0/0.0.0 [4C [5C8192[7C QEMU_QEMU_HARDDISK[3C [4C[0;7m [67D | |
| [0;1m 8/0/0/0.1.0 [4C [3C8192 [6C QEMU_QEMU_HARDDISK[3C [4C[0;7m [67D | |
| [0;1m [6C [4C [6C [6C [21C [4C[0;1;7mv[69D | |
| [0;1mm[0;1;7m< [0;7m [0;1;7m>[0;1mj[69D | |
| [46D[16A[16D | |
| [2C[11A+---------------------+----------------+-------------------+[60D | |
| | Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[58D | |
| CD/DVDs:[2C [C 1 [4CTapes: [7CMemory: [2C5[C2Mb[56D | |
| Graphics[CPorts:[C0[6CIO Buses:[C1[5CCPUs: [5C [C [58D | |
| +---------------------+----------------+-------------------+[60D | |
| [62D | |
| Disk[CDrives:[12D | |
| H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D[2C[11A| Disks: 2 ( 16.0GB) | Floppies: 0 | LAN cards: 1 |[58D | |
| CD/DVDs:[2C [C 1 [4CTapes: [7CMemory: [2C5[C2Mb[6C[0;7m [63D | |
| [0;1mGraphics[CPorts:[C0[6CIO Buses:[C1[5CCPUs: [5C [C [58D | |
| +---------------------+----------------+-------------------+[60D | |
| [62D | |
| Disk[CDrives:[54C[0;1;7m [67D | |
| [0;1m H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[54D[4C[11ACD/DVDs:[2C [C 1 [4CTapes: [7CMemory: [2C5[C2Mb[56D | |
| Graphics[CPorts:[C0[6CIO Buses:[C1[5CCPUs: [5C [C [58D | |
| +---------------------+----------------+-------------------+[60D | |
| [62D | |
| Disk[CDrives:[12D | |
| H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[65D[4C[11AGraphics[CPorts:[C0[6CIO Buses:[C1[5CCPUs: [5C [C [58D | |
| +---------------------+----------------+-------------------+[60D | |
| [4C[0;7m [67D | |
| [0;1mDisk[CDrives:[12D | |
| H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[55C[0;1;7m [65D | |
| [0;1m [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D[2C[11A+---------------------+----------------+-------------------+[60D | |
| [62D | |
| Disk[CDrives:[12D | |
| H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[18D[2C[11A [62D | |
| Disk[CDrives:[12D | |
| H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[8C[0;7m [57D | |
| [0;1m1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[12C[0;1;7m [65D | |
| [0;1m8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[18D | |
| 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[41D[11ADisk[CDrives:[12D | |
| H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[18D | |
| 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[39D | |
| [12C [41D[11A H/W Path [12CCapacity(Mb)[5CModel[44D | |
| 8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[51C[0;7m [67D | |
| [0;1m H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[48C[0;1;7m [67D | |
| [0;1m 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[39D | |
| [12C [41D | |
| I/O[CBuses:[10D[2C[11A8[C0/0/0.0.0[11C 8192 [4CQEMU_QEMU_HARDDISK[48D | |
| 1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[18D | |
| 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[39D | |
| [12C [41D | |
| I/O[CBuses:[10D | |
| 8/0/0/0 [15CSCSI_C895_Fast_Wide_LVD[48D[10C[11A1[9D | |
| [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [C[0;7m [67D | |
| [0;1mCD/DVD-ROM[CDrives:[18D | |
| 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[39D | |
| [12C [41D | |
| I/O[CBuses:[56C[0;1;7m [67D | |
| [0;1m 8/0/0/0 [15CSCSI_C895_Fast_Wide_LVD[46D | |
| [16C [48D[2C[11A [12C [11C [58D | |
| LAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[18D | |
| 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[39D | |
| [12C [41D | |
| I/O[CBuses:[10D | |
| 8/0/0/0 [15CSCSI_C895_Fast_Wide_LVD[46D | |
| [16C [48D | |
| Processors:[11D[11ALAN[CInterfaces:[15D | |
| H/W Path Interface[CName[3CLAN[CAddress[3CDescription[52D | |
| 8[C0/1/0 [2C lan0 [C [3C525400123456[2C HP_PCI_10/100Base-TX_[63D | |
| [5C [11C [3C [65D | |
| CD/DVD-ROM[CDrives:[18D | |
| 8/0/0/0.2.0 [7CQEMU_QEMU_CD-ROM[39D | |
| [12C [25C[0;7m [67D | |
| [0;1mI/O[CBuses:[10D | |
| 8/0/0/0 [15CSCSI_C895_Fast_Wide_LVD[46D | |
| [16C [48D | |
| Processors:[55C[0;1;7m [67D | |
| [0;1m 48 [14CProcessor[34D[23;5H[0;1;7m [0;1;4;7mO[0;1;7mK [8D[0;1m [0;1;4mO[0;1mK [8D[0;1;7m [0;1;4;7mO[0;1;7mK [8D[17C[22A Install HP-UX wizard: System Summary [56D | |
| [0;1m [41D | |
| [C [C [C [C [C [C [41D | |
| Congratulations, you[Chave[Csuccessfully[Cdefined your system. Please [75D | |
| use the "Show Summary" button to view a summary of how your system [2C [75D | |
| will[Cbe co[Cfigured. [CIf[Cyou[Csee[Cany[Cproblems,[Cor[Cwish[Cto[Cchange[Cany[Cof[C [2C [75D | |
| your[Cselections,[Cfeel [Cre[2Cto back up[Cto the appropriate step[Cand[Cmake[C [2C [75D | |
| the needed changes. [11C [3C [C [2C [75D | |
| [2C [67C [2C [75D | |
| [2C [C [C [48C [2C [75D | |
| [2C [3C [2C[[0;1;7m Show [0;1;4;7mS[0;1;7mummary... [0;1m] [25C [2C [75D | |
| [2C [67C [2C [75D | |
| [2C [C [C [56C [2C [75D | |
| Otherwise, select[C<Finish>[Cto[Cbegin installing your system![12C [2C [75D | |
| [2C [67C [2C [75D | |
| [2C [C [55C [2C [75D | |
| [2C [3C [21C [32C [2C [75D | |
| [2C [2C [75D | |
| [73C [76D | |
| qq[73Cq[76D | |
| [ < [0;1;4mB[0;1mack ] [ [0;1;4mF[0;1minish ] [ [0;1;4mC[0;1mancel ] [ [0;1;4mH[0;1melp ] [77D | |
| mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj[78D | |
| [55D[12A Show [0;1;4mS[0;1mummary... [20D[10B[0;1;7m < [0;1;4;7mB[0;1;7mack [8D[0;1m < [0;1;4mB[0;1mack [4C[0;1;7m [0;1;4;7mF[0;1;7minish [8D[0;1m [0;1;4mF[0;1minish [8D[0;1;7m [0;1;4;7mF[0;1;7minish [8D[10D[10A Show [0;1;4;7mS[0;1;7mummary... [36D[10B[0;1mWorking...[5C [C [C [C [2C [6C [C [C [6C [2C [2C [51D[10A[H[J[0m>[?7h[?25h[H[J * Loading configuration utility... | |
| * Beginning installation from source: /dev/dsk/c0t2d0 | |
| ======= 11/02/19 22:02:16 EST Starting system configuration... | |
| * Configure_Disks: Begin | |
| * Will install B.11.11 onto this system. | |
| * Creating LVM physical volume "/dev/rdsk/c0t1d0" (8/0/0/0.1.0). | |
| * Creating LVM physical volume "/dev/rdsk/c0t0d0" (8/0/0/0.0.0). | |
| * Creating volume group "vg00". | |
| * Creating logical volume "vg00/lvol1" (/stand). | |
| * Creating logical volume "vg00/lvol2" (swap_dump). | |
| * Creating logical volume "vg00/lvol3" (/). | |
| * Creating logical volume "vg00/lvol4" (/tmp). | |
| * Creating logical volume "vg00/lvol5" (/home). | |
| * Creating logical volume "vg00/lvol6" (/opt). | |
| * Creating logical volume "vg00/lvol7" (/usr). | |
| * Creating logical volume "vg00/lvol8" (/var). | |
| * Extending logical volume "vg00/lvol1" (/stand). | |
| * Extending logical volume "vg00/lvol2" (swap_dump). | |
| * Extending logical volume "vg00/lvol3" (/). | |
| * Extending logical volume "vg00/lvol4" (/tmp). | |
| * Extending logical volume "vg00/lvol5" (/home). | |
| * Extending logical volume "vg00/lvol6" (/opt). | |
| * Extending logical volume "vg00/lvol7" (/usr). | |
| * Extending logical volume "vg00/lvol8" (/var). | |
| * Making HFS filesystem for "/stand", (/dev/vg00/rlvol1). | |
| * Making VxFS filesystem for "/", (/dev/vg00/rlvol3). | |
| * Making VxFS filesystem for "/tmp", (/dev/vg00/rlvol4). | |
| * Making VxFS filesystem for "/home", (/dev/vg00/rlvol5). | |
| * Making VxFS filesystem for "/opt", (/dev/vg00/rlvol6). | |
| * Making VxFS filesystem for "/usr", (/dev/vg00/rlvol7). | |
| * Making VxFS filesystem for "/var", (/dev/vg00/rlvol8). | |
| * Configure_Disks: Complete | |
| * Download_mini-system: Begin | |
| x ./sbin/fs/hfs/mkfs, 290816 bytes, 568 tape blocks | |
| x ./sbin/fs/hfs/newfs, 212992 bytes, 416 tape blocks | |
| x ./sbin/fs/vxfs/mkfs, 393216 bytes, 768 tape blocks | |
| x ./sbin/fs/vxfs/newfs, 327680 bytes, 640 tape blocks | |
| x ./sbin/mkfs symbolic link to /sbin/fs_wrapper | |
| x ./sbin/newfs symbolic link to /sbin/fs_wrapper | |
| x ./sbin/lib/mfsconfig.d/hfs, 978 bytes, 2 tape blocks | |
| x ./sbin/lib/mfsconfig.d/vxfs, 966 bytes, 2 tape blocks | |
| x ./sbin/fs_wrapper, 233472 bytes, 456 tape blocks | |
| x ./sbin/sh, 401408 bytes, 784 tape blocks | |
| x ./usr/bin/mediainit, 32768 bytes, 64 tape blocks | |
| x ./usr/sbin/tunefs, 20480 bytes, 40 tape blocks | |
| x ./sbin/extendfs symbolic link to /sbin/fs_wrapper | |
| x ./sbin/fs/vxfs/extendfs, 319488 bytes, 624 tape blocks | |
| x ./sbin/fs/hfs/extendfs, 245760 bytes, 480 tape blocks | |
| x ./sbin/lvchange, 831488 bytes, 1624 tape blocks | |
| ./sbin/lvcreate linked to ./sbin/lvchange | |
| ./sbin/lvdisplay linked to ./sbin/lvchange | |
| ./sbin/lvextend linked to ./sbin/lvchange | |
| ./sbin/lvlnboot linked to ./sbin/lvchange | |
| ./sbin/lvreduce linked to ./sbin/lvchange | |
| ./sbin/lvremove linked to ./sbin/lvchange | |
| ./sbin/lvrmboot linked to ./sbin/lvchange | |
| ./sbin/pvchange linked to ./sbin/lvchange | |
| ./sbin/pvcreate linked to ./sbin/lvchange | |
| ./sbin/pvdisplay linked to ./sbin/lvchange | |
| ./sbin/pvmove linked to ./sbin/lvchange | |
| ./sbin/vgcfgbackup linked to ./sbin/lvchange | |
| ./sbin/vgcfgrestore linked to ./sbin/lvchange | |
| ./sbin/vgchange linked to ./sbin/lvchange | |
| ./sbin/vgcreate linked to ./sbin/lvchange | |
| ./sbin/vgdisplay linked to ./sbin/lvchange | |
| ./sbin/vgexport linked to ./sbin/lvchange | |
| ./sbin/vgextend linked to ./sbin/lvchange | |
| ./sbin/vgimport linked to ./sbin/lvchange | |
| ./sbin/vgreduce linked to ./sbin/lvchange | |
| ./sbin/vgremove linked to ./sbin/lvchange | |
| ./sbin/vgscan linked to ./sbin/lvchange | |
| ./sbin/pvck linked to ./sbin/lvchange | |
| x ./usr/bin/lifcp, 36864 bytes, 72 tape blocks | |
| x ./usr/bin/lifls, 24576 bytes, 48 tape blocks | |
| x ./usr/bin/lifrm, 20480 bytes, 40 tape blocks | |
| x ./usr/bin/basename, 12288 bytes, 24 tape blocks | |
| x ./usr/bin/chgrp, 20480 bytes, 40 tape blocks | |
| x ./usr/bin/cmp, 20480 bytes, 40 tape blocks | |
| x ./usr/bin/cp, 28672 bytes, 56 tape blocks | |
| x ./usr/bin/cut, 20480 bytes, 40 tape blocks | |
| x ./usr/bin/dd, 24576 bytes, 48 tape blocks | |
| x ./usr/bin/dirname, 12288 bytes, 24 tape blocks | |
| x ./usr/bin/egrep, 24576 bytes, 48 tape blocks | |
| x ./usr/bin/expr, 20480 bytes, 40 tape blocks | |
| x ./usr/bin/false, 12288 bytes, 24 tape blocks | |
| ./usr/bin/fgrep linked to ./usr/bin/egrep | |
| x ./usr/bin/getopts, 163 bytes, 1 tape blocks | |
| ./usr/bin/grep linked to ./usr/bin/egrep | |
| x ./usr/bin/hostname, 12288 bytes, 24 tape blocks | |
| x ./usr/bin/kill, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/ln, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/model, 24576 bytes, 48 tape blocks | |
| x ./usr/bin/ps, 36864 bytes, 72 tape blocks | |
| x ./usr/bin/pwd, 12288 bytes, 24 tape blocks | |
| x ./usr/bin/rm, 28672 bytes, 56 tape blocks | |
| ./usr/bin/rmdir linked to ./usr/bin/rm | |
| x ./usr/bin/sed, 40960 bytes, 80 tape blocks | |
| x ./usr/bin/sort, 40960 bytes, 80 tape blocks | |
| x ./usr/bin/tar, 45056 bytes, 88 tape blocks | |
| x ./usr/bin/touch, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/true, 12288 bytes, 24 tape blocks | |
| x ./usr/bin/uname, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/wc, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/compress, 28672 bytes, 56 tape blocks | |
| x ./usr/bin/ed, 57344 bytes, 112 tape blocks | |
| x ./usr/bin/find, 57344 bytes, 112 tape blocks | |
| x ./usr/bin/getopt, 12288 bytes, 24 tape blocks | |
| x ./usr/bin/id, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/more, 65536 bytes, 128 tape blocks | |
| x ./usr/bin/tail, 20480 bytes, 40 tape blocks | |
| ./usr/bin/uncompress linked to ./usr/bin/compress | |
| ./usr/bin/zcat linked to ./usr/bin/compress | |
| x ./usr/bin/bdf, 20480 bytes, 40 tape blocks | |
| x ./usr/bin/diff, 36864 bytes, 72 tape blocks | |
| x ./usr/bin/mt, 16384 bytes, 32 tape blocks | |
| x ./usr/bin/ftp, 114688 bytes, 224 tape blocks | |
| x ./usr/bin/rcp, 45056 bytes, 88 tape blocks | |
| x ./usr/bin/remsh, 28672 bytes, 56 tape blocks | |
| x ./usr/bin/ex, 241664 bytes, 472 tape blocks | |
| ./usr/bin/vi linked to ./usr/bin/ex | |
| x ./usr/lib/uxbootlf, 707584 bytes, 1382 tape blocks | |
| x ./usr/lib/libHcurses.sl symbolic link to /usr/lib/libcurses.1 | |
| x ./usr/lib/libM.1 symbolic link to ./libm.1 | |
| x ./usr/lib/libc.1, 1515520 bytes, 2960 tape blocks | |
| x ./usr/lib/libc.2, 1359872 bytes, 2656 tape blocks | |
| x ./usr/lib/libcl.2, 987136 bytes, 1928 tape blocks | |
| x ./usr/lib/libcurses.1, 155648 bytes, 304 tape blocks | |
| x ./usr/lib/libdld.1, 12288 bytes, 24 tape blocks | |
| x ./usr/lib/libdld.2, 20480 bytes, 40 tape blocks | |
| x ./usr/lib/libdld.sl symbolic link to ./libdld.2 | |
| x ./usr/lib/libfab.1, 20480 bytes, 40 tape blocks | |
| x ./usr/lib/libfab.sl symbolic link to ./libfab.1 | |
| x ./usr/lib/libm.1, 98773 bytes, 193 tape blocks | |
| x ./usr/lib/libm.2, 184320 bytes, 360 tape blocks | |
| x ./usr/lib/libm.sl symbolic link to ./libm.2 | |
| x ./usr/lib/libnss_files.1, 36864 bytes, 72 tape blocks | |
| x ./usr/lib/libpthread.1, 106496 bytes, 208 tape blocks | |
| x ./usr/lib/libsec.2, 114688 bytes, 224 tape blocks | |
| x ./usr/lib/libxcurses.1, 315392 bytes, 616 tape blocks | |
| x ./usr/lib/nls/msg/C/dcerpc.cat, 13755 bytes, 27 tape blocks | |
| x ./usr/lib/nls/msg/C/cpp.cat, 10542 bytes, 21 tape blocks | |
| x ./usr/lib/libnsl.1, 602112 bytes, 1176 tape blocks | |
| x ./usr/lib/libnsl.sl symbolic link to /usr/lib/libnsl.1 | |
| x ./usr/lib/libnss_dns.1, 20480 bytes, 40 tape blocks | |
| x ./usr/lib/libxti.2, 110592 bytes, 216 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_addhost.ui, 2420 bytes, 5 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_analyze.ui, 4663 bytes, 10 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_bundles.ui, 1775 bytes, 4 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_chgloc.ui, 3484 bytes, 7 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_defs.h, 24742 bytes, 49 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_depend.ui, 2824 bytes, 6 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_details.ui, 3990 bytes, 8 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_dsa.ui, 8100 bytes, 16 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_init.ui, 708 bytes, 2 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_install.ui, 4018 bytes, 8 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_jobopts.ui, 111005 bytes, 217 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_jobs.ui, 20222 bytes, 40 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_list.ui, 1962 bytes, 4 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_menudefs.h, 1792 bytes, 4 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_options.ui, 5889 bytes, 12 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_patch.ui, 2527 bytes, 5 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_remove.ui, 3289 bytes, 7 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_rmsourc.ui, 2411 bytes, 5 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_sched.ui, 4591 bytes, 9 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_selalt.ui, 2650 bytes, 6 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_seldpt.ui, 2245 bytes, 5 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_session.ui, 2014 bytes, 4 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_softinf.ui, 5653 bytes, 12 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_softwar.ui, 18847 bytes, 37 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_source.ui, 4745 bytes, 10 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_targets.ui, 12190 bytes, 24 tape blocks | |
| x ./usr/lib/sw/ui/C/smc_task.ui, 5805 bytes, 12 tape blocks | |
| x ./usr/lib/sw/help/C/sduhelp.hv, 28436 bytes, 56 tape blocks | |
| x ./usr/lib/sw/help/C/sduhelp.hvk, 5145 bytes, 11 tape blocks | |
| x ./usr/lib/sw/help/C/sduhelp00.ht, 215411 bytes, 421 tape blocks | |
| x ./usr/lib/sw/help/C/sduhelp01.ht, 14210 bytes, 28 tape blocks | |
| x ./usr/lib/libcma.1, 462848 bytes, 904 tape blocks | |
| x ./usr/lib/libcma.2, 483328 bytes, 944 tape blocks | |
| x ./usr/lib/libcma.sl symbolic link to ./libcma.2 | |
| x ./usr/lib/libd4r.1, 45056 bytes, 88 tape blocks | |
| x ./usr/lib/libd4r.sl symbolic link to ./libd4r.1 | |
| x ./usr/lib/libdce.1, 4235264 bytes, 8272 tape blocks | |
| x ./usr/lib/libdce.2, 4292608 bytes, 8384 tape blocks | |
| x ./usr/lib/libdce.sl symbolic link to ./libdce.2 | |
| x ./usr/lib/libdcekt.1, 4427776 bytes, 8648 tape blocks | |
| x ./usr/lib/libsis.sl, 1044480 bytes, 2040 tape blocks | |
| x ./usr/lib/dld.sl, 155648 bytes, 304 tape blocks | |
| x ./usr/lib/libdc.sl, 45056 bytes, 88 tape blocks | |
| x ./usr/sbin/devnm, 16384 bytes, 32 tape blocks | |
| x ./usr/sbin/diskinfo, 24576 bytes, 48 tape blocks | |
| x ./usr/sbin/insf symbolic link to /sbin/mksf | |
| x ./usr/sbin/ioinit symbolic link to /sbin/ioinit | |
| x ./usr/sbin/ioscan symbolic link to /sbin/ioscan | |
| x ./usr/sbin/mknod symbolic link to /sbin/mknod | |
| x ./usr/sbin/mount symbolic link to /sbin/mount | |
| x ./usr/sbin/reboot symbolic link to /sbin/reboot | |
| x ./usr/sbin/setboot, 20480 bytes, 40 tape blocks | |
| x ./usr/sbin/swapon, 28672 bytes, 56 tape blocks | |
| x ./usr/sbin/umount symbolic link to /sbin/umount | |
| x ./usr/sbin/chroot, 12288 bytes, 24 tape blocks | |
| x ./usr/sbin/rvxdump symbolic link to /usr/lbin/fs/vxfs/vxdump | |
| x ./usr/sbin/rvxrestore symbolic link to /usr/lbin/fs/vxfs/vxrestore | |
| x ./usr/sbin/vxdump symbolic link to /usr/lbin/fs/vxfs/vxdump | |
| x ./usr/sbin/vxrestore symbolic link to /usr/lbin/fs/vxfs/vxrestore | |
| x ./usr/sbin/mk_kernel, 27494 bytes, 54 tape blocks | |
| x ./usr/sbin/swagentd, 602112 bytes, 1176 tape blocks | |
| x ./usr/sbin/swacl, 2027520 bytes, 3960 tape blocks | |
| ./usr/sbin/swconfig linked to ./usr/sbin/swacl | |
| ./usr/sbin/swcopy linked to ./usr/sbin/swacl | |
| ./usr/sbin/swinstall linked to ./usr/sbin/swacl | |
| ./usr/sbin/swlist linked to ./usr/sbin/swacl | |
| x ./usr/sbin/swmodify, 1163264 bytes, 2272 tape blocks | |
| ./usr/sbin/swpackage linked to ./usr/sbin/swmodify | |
| ./usr/sbin/swreg linked to ./usr/sbin/swacl | |
| ./usr/sbin/swremove linked to ./usr/sbin/swacl | |
| ./usr/sbin/swverify linked to ./usr/sbin/swacl | |
| x ./usr/share/lib/terminfo/h/hp, 1448 bytes, 3 tape blocks | |
| x ./usr/share/lib/terminfo/v/vt100, 1358 bytes, 3 tape blocks | |
| x ./usr/share/lib/terminfo/w/wy60, 1673 bytes, 4 tape blocks | |
| x ./usr/conf/gen/templates/generic, 542 bytes, 2 tape blocks | |
| x ./usr/ccs/lbin/cpp, 290816 bytes, 568 tape blocks | |
| x ./usr/lbin/fs/vxfs/vxdump, 110592 bytes, 216 tape blocks | |
| x ./usr/lbin/fs/vxfs/vxrestore, 126976 bytes, 248 tape blocks | |
| x ./usr/lbin/sw/control_utils, 122219 bytes, 239 tape blocks | |
| x ./usr/lbin/swagent, 1417216 bytes, 2768 tape blocks | |
| x ./usr/lbin/sysadm/create_sysfile, 24576 bytes, 48 tape blocks | |
| x ./usr/lbin/sysadm/system_prep, 10000 bytes, 20 tape blocks | |
| x ./usr/obam/lbin/gethelp, 1236992 bytes, 2416 tape blocks | |
| x ./usr/obam/lbin/ui_exec, 12288 bytes, 24 tape blocks | |
| x ./usr/obam/lib/libIDMawrt.1, 1995529 bytes, 3898 tape blocks | |
| x ./usr/obam/lib/libIDMawrt.sl symbolic link to ./libIDMawrt.1 | |
| x ./usr/obam/lib/libobam.1, 1032192 bytes, 2016 tape blocks | |
| x ./usr/obam/lib/libobam.sl symbolic link to ./libobam.1 | |
| x ./usr/obam/lib/obam_aw.dmb, 149652 bytes, 293 tape blocks | |
| x ./usr/obam/lib/help/C/ui/ui.sdl, 81025 bytes, 159 tape blocks | |
| x ./usr/contrib/bin/gunzip, 90112 bytes, 176 tape blocks | |
| ./usr/contrib/bin/gzip linked to ./usr/contrib/bin/gunzip | |
| x ./sbin/awk, 397312 bytes, 776 tape blocks | |
| x ./sbin/cat, 208896 bytes, 408 tape blocks | |
| x ./sbin/chmod, 249856 bytes, 488 tape blocks | |
| x ./sbin/chown, 258048 bytes, 504 tape blocks | |
| x ./sbin/date, 241664 bytes, 472 tape blocks | |
| x ./sbin/frecover, 368640 bytes, 720 tape blocks | |
| x ./sbin/fs/cdfs/mount, 229376 bytes, 448 tape blocks | |
| x ./sbin/fs/cdfs/umount symbolic link to /sbin/fs/hfs/umount | |
| x ./sbin/fs/hfs/fsck, 339968 bytes, 664 tape blocks | |
| x ./sbin/fs/hfs/mount, 229376 bytes, 448 tape blocks | |
| x ./sbin/fs/hfs/umount, 192512 bytes, 376 tape blocks | |
| x ./sbin/fs/vxfs/fsck, 495616 bytes, 968 tape blocks | |
| x ./sbin/fs/vxfs/mount, 458752 bytes, 896 tape blocks | |
| x ./sbin/fs/vxfs/umount symbolic link to /sbin/fs/hfs/umount | |
| x ./sbin/fsck symbolic link to /sbin/fs_wrapper | |
| x ./sbin/init, 299008 bytes, 584 tape blocks | |
| x ./sbin/insf, 393216 bytes, 768 tape blocks | |
| x ./sbin/ioinit, 221184 bytes, 432 tape blocks | |
| x ./sbin/ioscan, 229376 bytes, 448 tape blocks | |
| x ./sbin/ls, 286720 bytes, 560 tape blocks | |
| x ./sbin/mkboot, 274432 bytes, 536 tape blocks | |
| x ./sbin/mkdir, 200704 bytes, 392 tape blocks | |
| x ./sbin/mknod, 192512 bytes, 376 tape blocks | |
| x ./sbin/mount, 274432 bytes, 536 tape blocks | |
| x ./sbin/mv, 241664 bytes, 472 tape blocks | |
| x ./sbin/pax, 389120 bytes, 760 tape blocks | |
| x ./sbin/reboot, 245760 bytes, 480 tape blocks | |
| x ./sbin/stty, 208896 bytes, 408 tape blocks | |
| x ./sbin/umount, 221184 bytes, 432 tape blocks | |
| x ./sbin/restore, 290816 bytes, 568 tape blocks | |
| x ./dev/config, 0 bytes, 0 blocks, character device | |
| x ./dev/null, 0 bytes, 0 blocks, character device | |
| x ./dev/console, 0 bytes, 0 blocks, character device | |
| x ./dev/kmem, 0 bytes, 0 blocks, character device | |
| x ./dev/mem, 0 bytes, 0 blocks, character device | |
| x ./dev/rroot, 0 bytes, 0 blocks, character device | |
| x ./dev/root, 0 bytes, 0 blocks, character device | |
| x ./dev/tty, 0 bytes, 0 blocks, character device | |
| x ./dev/syscon, 0 bytes, 0 blocks, character device | |
| x ./dev/systty, 0 bytes, 0 blocks, character device | |
| x ./tmp/set_locale, 3115 bytes, 7 tape blocks | |
| x ./var/adm/sw/security/_ACL, 40 bytes, 1 tape blocks | |
| x ./var/adm/sw/security/_OWNER, 62 bytes, 1 tape blocks | |
| x ./var/adm/sw/security/_PROD_DFLT_ACL, 55 bytes, 1 tape blocks | |
| x ./var/adm/sw/security/_SOC_DFLT_ACL, 55 bytes, 1 tape blocks | |
| x ./var/adm/sw/security/secrets, 15 bytes, 1 tape blocks | |
| x ./var/adm/sw/defaults, 1252 bytes, 3 tape blocks | |
| x ./var/opt/ignite/local/manifest/template.def, 14257 bytes, 28 tape blocks | |
| x ./opt/ignite/share/man/man1m.Z/print_manifest.1m, 1195 bytes, 3 tape blocks | |
| x ./opt/ignite/binpa/print_manifest, 40960 bytes, 80 tape blocks | |
| x ./opt/ignite/bin symbolic link to /opt/ignite/binpa | |
| x ./etc/group, 184 bytes, 1 tape blocks | |
| x ./etc/passwd, 332 bytes, 1 tape blocks | |
| x ./etc/magic, 8794 bytes, 18 tape blocks | |
| x ./etc/hosts, 486 bytes, 1 tape blocks | |
| x ./etc/services, 10908 bytes, 22 tape blocks | |
| x ./etc/inetsvcs.conf, 15 bytes, 1 tape blocks | |
| x ./etc/nsswitch.conf, 382 bytes, 1 tape blocks | |
| x ./configure3, 483328 bytes, 944 tape blocks | |
| x ./monitor_bpr, 32768 bytes, 64 tape blocks | |
| * Download_mini-system: Complete | |
| * Loading_software: Begin | |
| * Installing boot area on disk. | |
| * Enabling swap areas. | |
| * Backing up LVM configuration for "vg00". | |
| * Running the ioinit command ("/sbin/ioinit -c") | |
| * Creating device files via the insf command. | |
| insf: Installing special files for sdisk instance 0 address 8/0/0/0.0.0 | |
| insf: Installing special files for sdisk instance 1 address 8/0/0/0.1.0 | |
| insf: Installing special files for sdisk instance 2 address 8/0/0/0.2.0 | |
| insf: Installing special files for btlan instance 0 address 8/0/1/0 | |
| insf: Installing special files for pseudo driver dlpi | |
| insf: Installing special files for pseudo driver kepd | |
| insf: Installing special files for pseudo driver framebuf | |
| insf: Installing special files for pseudo driver sad | |
| * Constructing the bootconf file. | |
| * Setting primary boot path to "8/0/0/0.0.0". | |
| * Starting swinstall of the source (B7994 11i Mission Critical OE: CD1). | |
| * Running command: "/usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM | |
| -f/tmp/ign_configure/software_file -x os_release=B.11.11 -x | |
| os_name=HP-UX:32 -xpatch_filter=*.* -xpatch_save_files=true " | |
| WARNING: The software specified contains a fileset that changes the | |
| kernel. Either the attribute dynamic_module, used for dynamic | |
| changes, is specified, or the is_kernel attribute, used for | |
| static changes, is set to true. | |
| * Beginning Analysis Phase. | |
| * Source: localhost:/tmp/ign_configure/SD_CDROM | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for product information. | |
| NOTE: The filesystems in the filesystem table will not be checked | |
| against those currently mounted because the | |
| "mount_all_filesystems" option is set to "false". | |
| * Reading source for file information. | |
| NOTE: The Obsolete product is relevant during an update where there | |
| is existing software on the system to be obsoleted (removed). | |
| NOTE: The "checkinstall" script for "Obsolete" gave an "exclude" | |
| return (exit code "3"). The script location was | |
| "/var/tmp/BAAa00143/catalog/Obsolete/pfiles/checkinstall". | |
| NOTE: This software will be excluded from further processing. | |
| NOTE: The Update-UX.SD-AGENT fileset is intended to be installed | |
| only during execution of the update-ux command. Thus, the | |
| Update-UX.SD-AGENT fileset will exclude itself from | |
| installation at this time. | |
| NOTE: The "checkinstall" script for "Update-UX.SD-AGENT" gave an | |
| "exclude" return (exit code "3"). The script location was | |
| "/var/tmp/BAAa00143/catalog/Update-UX/SD-AGENT/checkinstall". | |
| NOTE: This software will be excluded from further processing. | |
| NOTE: The Update-UX.SD-CMDS fileset is intended to be installed | |
| only during execution of the update-ux command. Thus, the | |
| Update-UX.SD-CMDS fileset will exclude itself from | |
| installation at this time. | |
| NOTE: The "checkinstall" script for "Update-UX.SD-CMDS" gave an | |
| "exclude" return (exit code "3"). The script location was | |
| "/var/tmp/BAAa00143/catalog/Update-UX/SD-CMDS/checkinstall". | |
| NOTE: This software will be excluded from further processing. | |
| NOTE: The patch, PHCO_29379, will install correctly on your current | |
| system configuration; however, if you ever choose to install | |
| the product B2491BA, "MirrorDisk/UX", you will need to reapply | |
| the patch afterwards. PHCO_29379 includes components for both | |
| LVM and MirrorDisk/UX, so the MirrorDisk/UX component will | |
| need to be applied after the product is installed. This is | |
| accomplished by installing the patch again with the | |
| "reinstall" option set to false, which will install only the | |
| PHCO_29379.LVM-MIRROR-RUN fileset. | |
| NOTE: The firmware delivered in PHSS_29342 does not apply to | |
| the hardware model '9000/778/B160L' so the patch will be | |
| excluded from installation. | |
| If you wish to install PHSS_29342 even though it does not | |
| apply, you can force the installation of the patch by | |
| touching the file '/tmp/force_patch_install' before | |
| installing the patch. This may be useful when creating | |
| a 'golden' archive image for Ignite-UX that may be used | |
| on several different hardware platforms. Even though | |
| the installation of PHSS_29342 can be forced, the system | |
| firmware will not be modified since it does not apply to | |
| this hardware model. | |
| NOTE: The "checkinstall" script for "PHSS_29342.KERN-RUN" gave an | |
| "exclude" return (exit code "3"). The script location was | |
| "/var/tmp/BAAa00143/catalog/PHSS_29342/KERN-RUN/checkinstall". | |
| NOTE: This software will be excluded from further processing. | |
| NOTE: The SW-GETTOOLS product is intended to be installed with no | |
| other products/filesets. Thus, the SW-GETTOOLS product will | |
| exclude itself from installation. | |
| NOTE: The "checkinstall" script for "SW-GETTOOLS" gave an "exclude" | |
| return (exit code "3"). The script location was | |
| "/var/tmp/BAAa00143/catalog/SW-GETTOOLS/pfiles/checkinstall". | |
| NOTE: This software will be excluded from further processing. | |
| NOTE: The patch fileset "PHSS_26799.FC-TL-KRN,r=1.0" may only be | |
| installed upon a previously installed base fileset. The | |
| specification for this base fileset is | |
| "FC-TACHYON-TL.FC-TL-KRN,fr=B.11.11.09,v=HP". Since there is | |
| no fileset on the target or selected from the source which | |
| matches this specification, fileset | |
| "PHSS_26799.FC-TL-KRN,r=1.0" will be excluded. | |
| NOTE: The patch fileset "PHSS_26799.FC-TL-RUN,r=1.0" may only be | |
| installed upon a previously installed base fileset. The | |
| specification for this base fileset is | |
| "FC-TACHYON-TL.FC-TL-RUN,fr=B.11.11.09,v=HP". Since there is | |
| no fileset on the target or selected from the source which | |
| matches this specification, fileset | |
| "PHSS_26799.FC-TL-RUN,r=1.0" will be excluded. | |
| NOTE: The patch fileset "PHCO_23340.SD-AGENT,r=1.0" may only be | |
| installed upon a previously installed base fileset. The | |
| specification for this base fileset is | |
| "SW-DIST.SD-AGENT,fr=B.11.11,v=HP". Since there is no fileset | |
| on the target or selected from the source which matches this | |
| specification, fileset "PHCO_23340.SD-AGENT,r=1.0" will be | |
| excluded. | |
| NOTE: The patch fileset "PHCO_29379.LVM-MIRROR-RUN,r=1.0" may only | |
| be installed upon a previously installed base fileset. The | |
| specification for this base fileset is | |
| "LVM.LVM-MIRROR-RUN,fr=B.11.11,v=HP". Since there is no | |
| fileset on the target or selected from the source which | |
| matches this specification, fileset | |
| "PHCO_29379.LVM-MIRROR-RUN,r=1.0" will be excluded. | |
| * Executing preDSA command. | |
| NOTE: The used disk space on filesystem "/" is estimated to increase | |
| by 24488 Kbytes. | |
| This will leave 163856 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/usr" is estimated to | |
| increase by 697224 Kbytes. | |
| This will leave 1550056 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/var" is estimated to | |
| increase by 106384 Kbytes. | |
| This will leave 1416504 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/opt" is estimated to | |
| increase by 336976 Kbytes. | |
| This will leave 2148944 Kbytes of available user disk space | |
| after the installation. | |
| * Summary of Analysis Phase: | |
| * 26 of 749 filesets will be Skipped. | |
| * 723 of 749 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Install Execution Phase. | |
| * Filesets: 723 | |
| * Files: 39128 | |
| * Kbytes: 1019338 | |
| * Installing bundle "B6848BA,r=1.4.gm.46.9" . | |
| * Installing bundle "B8465BA,r=A.02.00.07" . | |
| * Installing bundle "B9073BA,r=B.11.11.07.01.00.00" . | |
| * Installing bundle "BUNDLE11i,r=B.11.11.0306.1" . | |
| * Installing bundle "FDDI-00,r=B.11.11.02" . | |
| * Installing bundle "FEATURE11-11,r=B.11.11.0209.5" . | |
| * Installing bundle "FibrChanl-00,r=B.11.11.12" . | |
| * Installing bundle "GigEther-00,r=B.11.11.19" . | |
| * Installing bundle "HPUXBase32,r=B.11.11" . | |
| * Installing bundle "HPUXBaseAux,r=B.11.11.0509" . | |
| * Installing bundle "HWEnable11i,r=B.11.11.0509.430" . | |
| * Installing bundle "MOZILLA,r=1.7.8.00.00" . | |
| * Installing bundle "MOZILLAsrc,r=1.7.8.00.00" . | |
| * Installing bundle "NPar,r=B.11.11.01.04.01.01" . | |
| * Installing bundle "OpenSSL,r=A.00.09.07e.012" . | |
| NOTE: Creating the initial "/stand/system" file using the | |
| "/usr/lbin/sysadm/create_sysfile" command. | |
| * Installing fileset "DCE-Core.DCE-CORE-SHLIB,r=B.11.11" (1 of | |
| 723). | |
| * File "/usr/lib/libcma.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * File "/usr/lib/libd4r.1" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * File "/usr/lib/libdce.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * Installing fileset "OS-Core.C-KRN,r=B.11.11" (2 of 723). | |
| * Installing fileset "OS-Core.KERN2-RUN,r=B.11.11" (3 of 723). | |
| * Installing fileset "OS-Core.KERN-RUN,r=B.11.11" (4 of 723). | |
| * Installing fileset "OS-Core.CORE2-KRN,r=B.11.11" (5 of 723). | |
| NOTE: Unable to determine if system hardware is SCA. Configure "sppnuma" | |
| into kernel if SCA use is desired. | |
| * Installing fileset "OS-Core.CORE-KRN,r=B.11.11" (6 of 723). | |
| NOTE: Truncating system files (/stand/system) to core drivers. | |
| * Installing fileset "OS-Core.SYS-ADMIN,r=B.11.11" (7 of 723). | |
| * Installing fileset "OS-Core.CORE-SHLIBS,r=B.11.11" (8 of 723). | |
| * File "/usr/lib/libc.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * File "/usr/lib/libdld.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * File "/usr/lib/libm.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * File "/usr/lib/libnss_files.1" could not be removed. It was | |
| renamed and added to the cleanup file | |
| "/var/adm/sw/cleanupfile". | |
| * File "/usr/lib/libsec.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| NOTE: /usr/bin/libc.2 has been replaced with a version specifically | |
| made for PA2.0 computers. The library can be changed back by | |
| executing libcadmin(1m). | |
| * Installing fileset "OS-Core.CMDS-MIN,r=B.11.11" (9 of 723). | |
| * Installing fileset "OS-Core.UX-CORE,r=B.11.11" (10 of 723). | |
| * Installing fileset "OS-Core.CMDS-AUX,r=B.11.11" (11 of 723). | |
| * Installing fileset "OS-Core.ADMN-ENG-A-MAN,r=B.11.11" (12 of | |
| 723). | |
| * Installing fileset "NFS.NFS-KRN,r=B.11.11" (13 of 723). | |
| * Installing fileset "NFS.NFS-SHLIBS,r=B.11.11" (14 of 723). | |
| * File "/usr/lib/libnsl.1" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * Installing fileset "NFS.NFS-CORE,r=B.11.11" (15 of 723). | |
| * Installing fileset "Networking.100BT-KRN,r=B.11.11" (16 of | |
| 723). | |
| * Installing fileset "Networking.LAN-KRN,r=B.11.11" (17 of 723). | |
| * Installing fileset "Networking.LAN2-KRN,r=B.11.11" (18 of | |
| 723). | |
| * Installing fileset "Networking.NET-KRN,r=B.11.11" (19 of 723). | |
| * Installing fileset "Networking.NET2-KRN,r=B.11.11" (20 of | |
| 723). | |
| * Installing fileset "Networking.NETTL-64SLIB,r=B.11.11" (21 of | |
| 723). | |
| * Installing fileset "Networking.NETTL-MIN,r=B.11.11" (22 of | |
| 723). | |
| * Installing fileset "Networking.NETTL-RUN,r=B.11.11" (23 of | |
| 723). | |
| * Installing fileset "Networking.NMS-KRN,r=B.11.11" (24 of 723). | |
| * Installing fileset "Networking.NMS2-KRN,r=B.11.11" (25 of | |
| 723). | |
| * Installing fileset "Networking.NET-RUN,r=B.11.11" (26 of 723). | |
| * Installing fileset "Networking.LAN-RUN,r=B.11.11" (27 of 723). | |
| * Installing fileset "Networking.NET-RUN-64,r=B.11.11" (28 of | |
| 723). | |
| * Installing fileset "Networking.NET-PRG,r=B.11.11" (29 of 723). | |
| * Installing fileset "Networking.100BT-RUN,r=B.11.11" (30 of | |
| 723). | |
| * Installing fileset "Networking.NW-ENG-A-MAN,r=B.11.11" (31 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS-RUN,r=B.11.11" (32 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS2-KRN,r=B.11.11" (33 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS-KRN,r=B.11.11" (34 of | |
| 723). | |
| * Installing fileset "Streams-TIO.STRTIO2-KRN,r=B.11.11" (35 of | |
| 723). | |
| * Installing fileset "Streams-TIO.STRTIO-KRN,r=B.11.11" (36 of | |
| 723). | |
| * Installing fileset "Streams-TIO.STRTIO-RUN,r=B.11.11" (37 of | |
| 723). | |
| * Installing fileset "InternetSrvcs.INETSVCS-INETD,r=B.11.11" | |
| (38 of 723). | |
| * Installing fileset "Upgrade.UPG-TLINK,r=B.11.11" (39 of 723). | |
| * Installing fileset "OVSNMPAgent.MASTER,r=B.11.11" (40 of 723). | |
| NOTE: You may need to restart SNMP agents. | |
| * Installing fileset "OVSNMPAgent.SUBAGT-HPUNIX,r=B.11.11" (41 | |
| of 723). | |
| NOTE: You may need to restart SNMP agents. | |
| * Installing fileset "OVSNMPAgent.SUBAGT-MIB2,r=B.11.11" (42 of | |
| 723). | |
| * Installing fileset "SW-DIST.SD-CMDS,r=B.11.11.0509.428" (43 of | |
| 723). | |
| * File "/usr/sbin/swverify" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * Installing fileset "SW-DIST.SD-AGENT,r=B.11.11.0509.428" (44 | |
| of 723). | |
| * File "/usr/lbin/swagent" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * File "/usr/sbin/swagentd" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * Installing fileset "SystemAdmin.OBAM-RUN,r=B.11.11" (45 of | |
| 723). | |
| * Installing fileset "FCMassStorage.FCMS-RUN,r=B.11.11" (46 of | |
| 723). | |
| * Installing fileset "FCMassStorage.FCMS-INIT,r=B.11.11" (47 of | |
| 723). | |
| * Installing fileset "FCMassStorage.FCMS-KRN,r=B.11.11" (48 of | |
| 723). | |
| * Installing fileset "FCMassStorage.FCMS-ENG-A-MAN,r=B.11.11" | |
| (49 of 723). | |
| * Installing fileset "TextFormatters.TEXT-FMT,r=B.11.11" (50 of | |
| 723). | |
| * Installing fileset "PHKL_30257.FCMS-RUN,r=1.0" (51 of 723). | |
| * Installing fileset "PHKL_30257.FCMS-KRN,r=1.0" (52 of 723). | |
| * Installing fileset "PHKL_30257.CORE2-KRN,r=1.0" (53 of 723). | |
| * Installing fileset "PHKL_30257.FCMS-ENG-A-MAN,r=1.0" (54 of | |
| 723). | |
| * Installing fileset "FC-TACHYON-TL.FC-TL-KRN,r=B.11.11.12" (55 | |
| of 723). | |
| * Installing fileset "FDDI-KRN-COM.FDDI467-KRN,r=B.11.11.01" (56 | |
| of 723). | |
| * Installing fileset "FDDI-PCI.FDDI4-KRN,r=B.11.11.02" (57 of | |
| 723). | |
| * Installing fileset "GE-DRV.GE-KRN,r=B.11.11.19" (58 of 723). | |
| * Installing fileset "JFS.VXFS-BASE-KRN,r=B.11.11" (59 of 723). | |
| * Installing fileset "LVM.LVM-KRN,r=B.11.11" (60 of 723). | |
| * Installing fileset "LVM.LVM-RUN,r=B.11.11" (61 of 723). | |
| * Installing fileset "PHCO_27103.UX-CORE,r=1.0" (62 of 723). | |
| * Installing fileset "PHKL_23290.KERN2-RUN,r=1.0" (63 of 723). | |
| * Installing fileset "PHKL_23292.CORE-KRN,r=1.0" (64 of 723). | |
| * Installing fileset "PHKL_23293.CORE-KRN,r=1.0" (65 of 723). | |
| * Installing fileset "ProgSupport.C-INC,r=B.11.11" (66 of 723). | |
| * Installing fileset "ProgSupport.PROG-MIN,r=B.11.11" (67 of | |
| 723). | |
| * Installing fileset "ProgSupport.PROG-AUX,r=B.11.11" (68 of | |
| 723). | |
| * Installing fileset "PHKL_23294.C-INC,r=1.0" (69 of 723). | |
| * Installing fileset "PHKL_23294.CORE-KRN,r=1.0" (70 of 723). | |
| * Installing fileset "PHKL_23295.C-INC,r=1.0" (71 of 723). | |
| * Installing fileset "PHKL_23295.CORE-KRN,r=1.0" (72 of 723). | |
| * Installing fileset "PHKL_23296.C-INC,r=1.0" (73 of 723). | |
| * Installing fileset "PHKL_23296.CORE-KRN,r=1.0" (74 of 723). | |
| * Installing fileset "PHKL_23297.C-INC,r=1.0" (75 of 723). | |
| * Installing fileset "PHKL_23297.CORE-KRN,r=1.0" (76 of 723). | |
| * Installing fileset "PHKL_23299.C-INC,r=1.0" (77 of 723). | |
| * Installing fileset "PHKL_23299.CORE-KRN,r=1.0" (78 of 723). | |
| * Installing fileset "KernDevKit.KERN-DEV-KIT,r=B.11.11" (79 of | |
| 723). | |
| * Installing fileset "PHKL_23301.CORE-KRN,r=1.0" (80 of 723). | |
| * Installing fileset "PHKL_23301.KERN-DEV-KIT,r=1.0" (81 of | |
| 723). | |
| * Installing fileset "PHKL_23302.C-INC,r=1.0" (82 of 723). | |
| * Installing fileset "PHKL_23302.CORE-KRN,r=1.0" (83 of 723). | |
| * Installing fileset "PHKL_23303.C-INC,r=1.0" (84 of 723). | |
| * Installing fileset "PHKL_23303.CORE-KRN,r=1.0" (85 of 723). | |
| * Installing fileset "PHKL_23304.C-INC,r=1.0" (86 of 723). | |
| * Installing fileset "PHKL_23304.CORE-KRN,r=1.0" (87 of 723). | |
| * Installing fileset "PHKL_23305.C-INC,r=1.0" (88 of 723). | |
| * Installing fileset "PHKL_23305.CORE-KRN,r=1.0" (89 of 723). | |
| * Installing fileset "PHKL_23306.C-INC,r=1.0" (90 of 723). | |
| * Installing fileset "PHKL_23306.CORE-KRN,r=1.0" (91 of 723). | |
| * Installing fileset "PHKL_23307.C-INC,r=1.0" (92 of 723). | |
| * Installing fileset "PHKL_23307.CORE-KRN,r=1.0" (93 of 723). | |
| * Installing fileset "PHKL_23308.C-INC,r=1.0" (94 of 723). | |
| * Installing fileset "PHKL_23308.CORE-KRN,r=1.0" (95 of 723). | |
| * Installing fileset "PHKL_23309.C-INC,r=1.0" (96 of 723). | |
| * Installing fileset "PHKL_23309.CORE-KRN,r=1.0" (97 of 723). | |
| * Installing fileset "PHKL_23310.C-INC,r=1.0" (98 of 723). | |
| * Installing fileset "PHKL_23310.CORE-KRN,r=1.0" (99 of 723). | |
| * Installing fileset "PHKL_23311.C-INC,r=1.0" (100 of 723). | |
| * Installing fileset "PHKL_23311.CORE-KRN,r=1.0" (101 of 723). | |
| * Installing fileset "PHKL_23312.C-INC,r=1.0" (102 of 723). | |
| * Installing fileset "PHKL_23312.CORE-KRN,r=1.0" (103 of 723). | |
| * Installing fileset "PHKL_23314.C-INC,r=1.0" (104 of 723). | |
| * Installing fileset "PHKL_23314.CORE-KRN,r=1.0" (105 of 723). | |
| * Installing fileset "PHKL_23315.C-INC,r=1.0" (106 of 723). | |
| * Installing fileset "PHKL_23315.CORE-KRN,r=1.0" (107 of 723). | |
| * Installing fileset "PHKL_23316.CORE-KRN,r=1.0" (108 of 723). | |
| * Installing fileset "PHKL_23625.CORE2-KRN,r=1.0" (109 of 723). | |
| * Installing fileset "PHKL_23666.KERN2-RUN,r=1.0" (110 of 723). | |
| * Installing fileset "PHKL_23810.CORE2-KRN,r=1.0" (111 of 723). | |
| * Installing fileset "PHKL_23957.CORE2-KRN,r=1.0" (112 of 723). | |
| * Installing fileset "PHKL_24278.CORE2-KRN,r=1.0" (113 of 723). | |
| * Installing fileset "PHKL_25506.C-INC,r=1.0" (114 of 723). | |
| * Installing fileset "PHKL_25506.CORE-KRN,r=1.0" (115 of 723). | |
| * Installing fileset "PHKL_25506.CORE2-KRN,r=1.0" (116 of 723). | |
| * Installing fileset "PHKL_26269.C-INC,r=1.0" (117 of 723). | |
| * Installing fileset "PHKL_26269.CORE-KRN,r=1.0" (118 of 723). | |
| * Installing fileset "PHKL_26425.CORE-KRN,r=1.0" (119 of 723). | |
| * Installing fileset "PHKL_26425.CORE2-KRN,r=1.0" (120 of 723). | |
| * Installing fileset "PHKL_26743.LVM-KRN,r=1.0" (121 of 723). | |
| * Installing fileset "PHKL_27096.CORE2-KRN,r=1.0" (122 of 723). | |
| * Installing fileset "PHKL_27155.CORE2-KRN,r=1.0" (123 of 723). | |
| * Installing fileset "PHKL_27219.CORE2-KRN,r=1.0" (124 of 723). | |
| * Installing fileset "PHKL_28025.C-INC,r=1.0" (125 of 723). | |
| * Installing fileset "PHKL_28025.CORE-KRN,r=1.0" (126 of 723). | |
| * Installing fileset "PHKL_28025.CORE2-KRN,r=1.0" (127 of 723). | |
| * Installing fileset "PHKL_28197.C-INC,r=1.0" (128 of 723). | |
| * Installing fileset "PHKL_28197.CORE2-KRN,r=1.0" (129 of 723). | |
| NOTE: Unable to find an usb device on the system. usb will not be | |
| put in the system file. | |
| * Installing fileset "PHKL_28569.CORE2-KRN,r=1.0" (130 of 723). | |
| * Installing fileset "PHKL_28839.CORE2-KRN,r=1.0" (131 of 723). | |
| * Installing fileset "PHKL_29529.C-INC,r=1.0" (132 of 723). | |
| * Installing fileset "PHKL_29529.CORE2-KRN,r=1.0" (133 of 723). | |
| NOTE: Unable to find an audio device on the system. Audio will not | |
| be put in the system file. To enable audio, edit | |
| /stand/system, add the line audio, rebuild the kernel and | |
| reboot. To enable the audio server, edit | |
| /etc/rc.config.d/audio and make sure the line AUDIO_SERVER= is | |
| set to 1. | |
| * Installing fileset "PHKL_29539.C-INC,r=1.0" (134 of 723). | |
| * Installing fileset "PHKL_29539.CORE-KRN,r=1.0" (135 of 723). | |
| * Installing fileset "PHKL_29539.CORE2-KRN,r=1.0" (136 of 723). | |
| * Installing fileset "PHKL_29567.CORE2-KRN,r=1.0" (137 of 723). | |
| * Installing fileset "PHKL_29651.CORE2-KRN,r=1.0" (138 of 723). | |
| * Installing fileset "PHKL_29700.C-INC,r=1.0" (139 of 723). | |
| * Installing fileset "PHKL_29700.CORE-KRN,r=1.0" (140 of 723). | |
| * Installing fileset "PHKL_29700.CORE2-KRN,r=1.0" (141 of 723). | |
| * Installing fileset "PHKL_30100.CORE2-KRN,r=1.0" (142 of 723). | |
| * Installing fileset "PHKL_30105.CORE2-KRN,r=1.0" (143 of 723). | |
| * Installing fileset "PHKL_30197.CORE2-KRN,r=1.0" (144 of 723). | |
| * Installing fileset "PHKL_30446.CORE2-KRN,r=1.0" (145 of 723). | |
| * Installing fileset "PHKL_30512.CORE2-KRN,r=1.0" (146 of 723). | |
| * Installing fileset "PHKL_30992.CORE2-KRN,r=1.0" (147 of 723). | |
| * Installing fileset "PHKL_31227.CORE2-KRN,r=1.0" (148 of 723). | |
| * Installing fileset "PHKL_31241.C-INC,r=1.0" (149 of 723). | |
| * Installing fileset "PHKL_31241.CORE-KRN,r=1.0" (150 of 723). | |
| * Installing fileset "PHKL_31241.CORE2-KRN,r=1.0" (151 of 723). | |
| * Installing fileset "PHKL_32089.CORE2-KRN,r=1.0" (152 of 723). | |
| * Installing fileset "PHKL_32090.ADMN-ENG-A-MAN,r=1.0" (153 of | |
| 723). | |
| * Installing fileset "PHKL_32090.C-INC,r=1.0" (154 of 723). | |
| * Installing fileset "PHKL_32090.CORE2-KRN,r=1.0" (155 of 723). | |
| * Installing fileset "PHKL_32647.C-INC,r=1.0" (156 of 723). | |
| * Installing fileset "PHKL_32647.CORE-KRN,r=1.0" (157 of 723). | |
| * Installing fileset "PHKL_32647.CORE2-KRN,r=1.0" (158 of 723). | |
| * Installing fileset "PHKL_33338.CORE2-KRN,r=1.0" (159 of 723). | |
| * Installing fileset "PHKL_33339.CORE2-KRN,r=1.0" (160 of 723). | |
| * Installing fileset "PHKL_33425.C-INC,r=1.0" (161 of 723). | |
| * Installing fileset "PHKL_33425.CORE-KRN,r=1.0" (162 of 723). | |
| * Installing fileset "PHKL_33425.CORE2-KRN,r=1.0" (163 of 723). | |
| * Installing fileset "PHKL_33425.KERN2-RUN,r=1.0" (164 of 723). | |
| * Installing fileset "PHNE_23288.C-INC,r=1.0" (165 of 723). | |
| * Installing fileset "PHNE_23288.CORE-KRN,r=1.0" (166 of 723). | |
| * Installing fileset "PHNE_23288.NET-KRN,r=1.0" (167 of 723). | |
| * Installing fileset "PHNE_23288.NET-PRG,r=1.0" (168 of 723). | |
| * Installing fileset "PHNE_28799.100BT-KRN,r=1.0" (169 of 723). | |
| * Installing fileset "PHNE_28799.100BT-RUN,r=1.0" (170 of 723). | |
| * Installing fileset "PHNE_28799.CORE2-KRN,r=1.0" (171 of 723). | |
| * Installing fileset "PHNE_30463.CORE2-KRN,r=1.0" (172 of 723). | |
| * Installing fileset "PHNE_30463.KERN2-RUN,r=1.0" (173 of 723). | |
| * Installing fileset "PHNE_32396.CORE2-KRN,r=1.0" (174 of 723). | |
| * Installing fileset "PHNE_32396.LAN-RUN,r=1.0" (175 of 723). | |
| * Installing fileset "PHNE_32396.LAN2-KRN,r=1.0" (176 of 723). | |
| * Installing fileset "PHNE_32396.NW-ENG-A-MAN,r=1.0" (177 of | |
| 723). | |
| * Installing fileset "SCSI-Passthru.SPT-DVR,r=B.11.11" (178 of | |
| 723). | |
| * Installing fileset "SCSI-Passthru.SPT2-DVR,r=B.11.11" (179 of | |
| 723). | |
| * Installing fileset "UserLicense.UNL-USER,r=B.11.11" (180 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-COR-64SLIB,r=B.11.11" (181 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-CORE-RUN,r=B.11.11" (182 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-CORE-DTS,r=B.11.11" (183 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-CORE-HELP,r=B.11.11" (184 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-CORE-NOTES,r=B.11.11" (185 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-JPN-E-MSG,r=B.11.11" (186 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCE-JPN-S-MSG,r=B.11.11" (187 of | |
| 723). | |
| * Installing fileset "DCE-Core.DCEC-ENG-A-MAN,r=B.11.11" (188 of | |
| 723). | |
| * Installing fileset "DCE-Core.MACR-ENG-A-MAN,r=B.11.11" (189 of | |
| 723). | |
| * Installing fileset "OS-Core.ADMN-JPN-E-MAN,r=B.11.11" (190 of | |
| 723). | |
| * Installing fileset "OS-Core.ADMN-JPN-S-MAN,r=B.11.11" (191 of | |
| 723). | |
| * Installing fileset "OS-Core.ARRAY-MGMT,r=B.11.11" (192 of | |
| 723). | |
| * Installing fileset "OS-Core.C-MIN,r=B.11.11" (193 of 723). | |
| * Installing fileset "OS-Core.C-MIN-32ALIB,r=B.11.11" (194 of | |
| 723). | |
| * Installing fileset "OS-Core.C-MIN-64ALIB,r=B.11.11" (195 of | |
| 723). | |
| * Installing fileset "OS-Core.C2400-UTIL,r=B.11.11" (196 of | |
| 723). | |
| * Installing fileset "OS-Core.CAUX-ENG-A-MAN,r=B.11.11" (197 of | |
| 723). | |
| * Installing fileset "OS-Core.CAUX-JPN-E-MAN,r=B.11.11" (198 of | |
| 723). | |
| * Installing fileset "OS-Core.CAUX-JPN-S-MAN,r=B.11.11" (199 of | |
| 723). | |
| * Installing fileset "OS-Core.CMDS-AX-64SLIB,r=B.11.11" (200 of | |
| 723). | |
| * Installing fileset "OS-Core.CMDS-MN-64SLIB,r=B.11.11" (201 of | |
| 723). | |
| * Installing fileset "OS-Core.CMIN-ENG-A-MAN,r=B.11.11" (202 of | |
| 723). | |
| * Installing fileset "OS-Core.CMIN-JPN-E-MAN,r=B.11.11" (203 of | |
| 723). | |
| * Installing fileset "OS-Core.CMIN-JPN-S-MAN,r=B.11.11" (204 of | |
| 723). | |
| * Installing fileset "OS-Core.CORE-64SLIB,r=B.11.11" (205 of | |
| 723). | |
| * Installing fileset "OS-Core.CORE-ENG-A-MAN,r=B.11.11" (206 of | |
| 723). | |
| * Installing fileset "OS-Core.CORE-JPN-E-MAN,r=B.11.11" (207 of | |
| 723). | |
| * Installing fileset "OS-Core.CORE-JPN-S-MAN,r=B.11.11" (208 of | |
| 723). | |
| * Installing fileset "OS-Core.HPUX-HELP,r=B.11.11" (209 of 723). | |
| * Installing fileset "OS-Core.KERN-ENG-A-MAN,r=B.11.11" (210 of | |
| 723). | |
| * Installing fileset "OS-Core.KERN-JPN-E-MAN,r=B.11.11" (211 of | |
| 723). | |
| * Installing fileset "OS-Core.KERN-JPN-S-MAN,r=B.11.11" (212 of | |
| 723). | |
| * Installing fileset "OS-Core.LINKER-HELP,r=B.11.11" (213 of | |
| 723). | |
| * Installing fileset "OS-Core.NLS-AUX,r=B.11.11" (214 of 723). | |
| * Installing fileset "OS-Core.PERL,r=B.11.11" (215 of 723). | |
| * Installing fileset "OS-Core.Q4,r=B.11.11" (216 of 723). | |
| * Installing fileset "OS-Core.RELEASE-NOTES,r=B.11.11" (217 of | |
| 723). | |
| * Installing fileset "OS-Core.TOOL-ENG-A-MAN,r=B.11.11" (218 of | |
| 723). | |
| * Installing fileset "OS-Core.TOOL-JPN-E-MAN,r=B.11.11" (219 of | |
| 723). | |
| * Installing fileset "OS-Core.TOOL-JPN-S-MAN,r=B.11.11" (220 of | |
| 723). | |
| * Installing fileset "OS-Core.UPS-TOOLS,r=B.11.11" (221 of 723). | |
| * Installing fileset "OS-Core.USRCONTRB,r=B.11.11" (222 of 723). | |
| * Installing fileset "OS-Core.UX-FRE-I-MSG,r=B.11.11" (223 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-FRE-U-MSG,r=B.11.11" (224 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-GER-I-MSG,r=B.11.11" (225 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-GER-U-MSG,r=B.11.11" (226 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-ITA-I-MSG,r=B.11.11" (227 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-ITA-U-MSG,r=B.11.11" (228 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-JPN-E-MSG,r=B.11.11" (229 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-JPN-S-MSG,r=B.11.11" (230 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-JPN-U-MSG,r=B.11.11" (231 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-KOR-E-MSG,r=B.11.11" (232 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-KOR-U-MSG,r=B.11.11" (233 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-SCH-H-MSG,r=B.11.11" (234 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-SCH-U-MSG,r=B.11.11" (235 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-SPA-I-MSG,r=B.11.11" (236 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-SPA-U-MSG,r=B.11.11" (237 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-TCH-B-MSG,r=B.11.11" (238 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-TCH-E-MSG,r=B.11.11" (239 of | |
| 723). | |
| * Installing fileset "OS-Core.UX-TCH-U-MSG,r=B.11.11" (240 of | |
| 723). | |
| * Installing fileset "NFS.KEY-CORE,r=B.11.11" (241 of 723). | |
| * Installing fileset "NFS.NFS-64ALIB,r=B.11.11" (242 of 723). | |
| * Installing fileset "NFS.NFS-64SLIB,r=B.11.11" (243 of 723). | |
| * Installing fileset "NFS.NFS-CLIENT,r=B.11.11" (244 of 723). | |
| * Installing fileset "NFS.NFS-ENG-A-MAN,r=B.11.11" (245 of 723). | |
| * Installing fileset "NFS.NFS-JPN-E-MAN,r=B.11.11" (246 of 723). | |
| * Installing fileset "NFS.NFS-JPN-S-MAN,r=B.11.11" (247 of 723). | |
| * Installing fileset "NFS.NFS-PRG,r=B.11.11" (248 of 723). | |
| * Installing fileset "NFS.NFS-SERVER,r=B.11.11" (249 of 723). | |
| * Installing fileset "NFS.NIS-CLIENT,r=B.11.11" (250 of 723). | |
| * Installing fileset "NFS.NIS-CORE,r=B.11.11" (251 of 723). | |
| * Installing fileset "NFS.NIS-SERVER,r=B.11.11" (252 of 723). | |
| * Installing fileset "NFS.NISPLUS-CORE,r=B.11.11" (253 of 723). | |
| * Installing fileset "Networking.LAN-PRG,r=B.11.11" (254 of | |
| 723). | |
| * Installing fileset "Networking.NETTL-ADM,r=B.11.11" (255 of | |
| 723). | |
| * Installing fileset "Networking.NMS-RUN,r=B.11.11" (256 of | |
| 723). | |
| * Installing fileset "Networking.NW-JPN-E-MAN,r=B.11.11" (257 of | |
| 723). | |
| * Installing fileset "Networking.NW-JPN-S-MAN,r=B.11.11" (258 of | |
| 723). | |
| * Installing fileset "Networking.PPP-RUN,r=B.11.11" (259 of | |
| 723). | |
| * Installing fileset "Streams.STRE-ENG-A-MAN,r=B.11.11" (260 of | |
| 723). | |
| * Installing fileset "Streams.STRE-JPN-E-MAN,r=B.11.11" (261 of | |
| 723). | |
| * Installing fileset "Streams.STRE-JPN-S-MAN,r=B.11.11" (262 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS-32ALIB,r=B.11.11" (263 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS-64ALIB,r=B.11.11" (264 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS-64SLIB,r=B.11.11" (265 of | |
| 723). | |
| * Installing fileset "Streams.STREAMS-MIN,r=B.11.11" (266 of | |
| 723). | |
| * File "/usr/lib/libxti.2" could not be removed. It was renamed | |
| and added to the cleanup file "/var/adm/sw/cleanupfile". | |
| * Installing fileset "Streams.XTI-ENG-A-MAN,r=B.11.11" (267 of | |
| 723). | |
| * Installing fileset "Streams.XTI-JPN-E-MAN,r=B.11.11" (268 of | |
| 723). | |
| * Installing fileset "Streams.XTI-JPN-S-MAN,r=B.11.11" (269 of | |
| 723). | |
| * Installing fileset "Streams-TIO.STIO-ENG-A-MAN,r=B.11.11" (270 | |
| of 723). | |
| * Installing fileset "Streams-TIO.STIO-JPN-E-MAN,r=B.11.11" (271 | |
| of 723). | |
| * Installing fileset "Streams-TIO.STIO-JPN-S-MAN,r=B.11.11" (272 | |
| of 723). | |
| * Installing fileset "InternetSrvcs.INET-ENG-A-MAN,r=B.11.11" | |
| (273 of 723). | |
| * Installing fileset "InternetSrvcs.INET-JPN-E-MAN,r=B.11.11" | |
| (274 of 723). | |
| * Installing fileset "InternetSrvcs.INET-JPN-S-MAN,r=B.11.11" | |
| (275 of 723). | |
| * Installing fileset "InternetSrvcs.INETSVCS-BOOT,r=B.11.11" | |
| (276 of 723). | |
| * Installing fileset "InternetSrvcs.INETSVCS-DTC,r=B.11.11" (277 | |
| of 723). | |
| * Installing fileset "InternetSrvcs.INETSVCS-INC,r=B.11.11" (278 | |
| of 723). | |
| * Installing fileset "InternetSrvcs.INETSVCS-RUN,r=B.11.11" (279 | |
| of 723). | |
| * Installing fileset "InternetSrvcs.RBTD-ENG-A-MAN,r=B.11.11" | |
| (280 of 723). | |
| * Installing fileset "InternetSrvcs.RBTD-JPN-E-MAN,r=B.11.11" | |
| (281 of 723). | |
| * Installing fileset "InternetSrvcs.RBTD-JPN-S-MAN,r=B.11.11" | |
| (282 of 723). | |
| * Installing fileset "Upgrade.UPG-JPN-E-MAN,r=B.11.11" (283 of | |
| 723). | |
| * Installing fileset "Upgrade.UPG-JPN-S-MAN,r=B.11.11" (284 of | |
| 723). | |
| * Installing fileset "Upgrade.UPG-MAN,r=B.11.11" (285 of 723). | |
| * Installing fileset "OVSNMPAgent.SNMP-ENG-A-MAN,r=B.11.11" (286 | |
| of 723). | |
| * Installing fileset "OVSNMPAgent.SNMP-JPN-E-MAN,r=B.11.11" (287 | |
| of 723). | |
| * Installing fileset "OVSNMPAgent.SNMP-JPN-S-MAN,r=B.11.11" (288 | |
| of 723). | |
| * Installing fileset "SW-DIST.GZIP,r=B.11.11.0509.428" (289 of | |
| 723). | |
| * Installing fileset "SW-DIST.SD-ENG-A-MAN,r=B.11.11.0509.428" | |
| (290 of 723). | |
| * Installing fileset "SW-DIST.SD-EXAMPLES,r=B.11.11.0509.428" | |
| (291 of 723). | |
| * Installing fileset "SW-DIST.SD-FAL,r=B.11.11.0509.428" (292 of | |
| 723). | |
| * Installing fileset "SW-DIST.SD-FRE-I-MSG,r=B.11.11.0509.428" | |
| (293 of 723). | |
| * Installing fileset "SW-DIST.SD-GER-I-MSG,r=B.11.11.0509.428" | |
| (294 of 723). | |
| * Installing fileset "SW-DIST.SD-HELP,r=B.11.11.0509.428" (295 | |
| of 723). | |
| * Installing fileset "SW-DIST.SD-JPN-E-HELP,r=B.11.11.0509.428" | |
| (296 of 723). | |
| * Installing fileset "SW-DIST.SD-JPN-E-MAN,r=B.11.11.0509.428" | |
| (297 of 723). | |
| * Installing fileset "SW-DIST.SD-JPN-E-MSG,r=B.11.11.0509.428" | |
| (298 of 723). | |
| * Installing fileset "SW-DIST.SD-JPN-S-HELP,r=B.11.11.0509.428" | |
| (299 of 723). | |
| * Installing fileset "SW-DIST.SD-JPN-S-MAN,r=B.11.11.0509.428" | |
| (300 of 723). | |
| * Installing fileset "SW-DIST.SD-JPN-S-MSG,r=B.11.11.0509.428" | |
| (301 of 723). | |
| * Installing fileset "SW-DIST.SD-KOR-E-MSG,r=B.11.11.0509.428" | |
| (302 of 723). | |
| * Installing fileset "SW-DIST.SD-TCH-B-MSG,r=B.11.11.0509.428" | |
| (303 of 723). | |
| * Installing fileset "SW-DIST.SD-TCH-H-MSG,r=B.11.11.0509.428" | |
| (304 of 723). | |
| * Installing fileset "SW-DIST.SD-UPDATE,r=B.11.11.0509.428" (305 | |
| of 723). | |
| * Installing fileset "SystemAdmin.SAM,r=B.11.11" (306 of 723). | |
| * Installing fileset "SystemAdmin.FIRST-BOOT,r=B.11.11" (307 of | |
| 723). | |
| * Installing fileset "SystemAdmin.SAM-HELP,r=B.11.11" (308 of | |
| 723). | |
| * Installing fileset "SystemAdmin.SAM-ENG-A-MAN,r=B.11.11" (309 | |
| of 723). | |
| * Installing fileset "SystemAdmin.OBAM-HELP,r=B.11.11" (310 of | |
| 723). | |
| * Installing fileset "SystemAdmin.SAM-JPN-E-MAN,r=B.11.11" (311 | |
| of 723). | |
| * Installing fileset "SystemAdmin.SAM-JPN-S-MAN,r=B.11.11" (312 | |
| of 723). | |
| * Installing fileset "FCMassStorage.FCMS-JPN-E-MAN,r=B.11.11" | |
| (313 of 723). | |
| * Installing fileset "FCMassStorage.FCMS-JPN-S-MAN,r=B.11.11" | |
| (314 of 723). | |
| * Installing fileset "TextFormatters.TEXT-ENG-A-MAN,r=B.11.11" | |
| (315 of 723). | |
| * Installing fileset "TextFormatters.TEXT-JPN-E-MAN,r=B.11.11" | |
| (316 of 723). | |
| * Installing fileset "TextFormatters.TEXT-JPN-S-MAN,r=B.11.11" | |
| (317 of 723). | |
| * Installing fileset "FC-TACHYON-TL.FC-TL-RUN,r=B.11.11.12" (318 | |
| of 723). | |
| * Installing fileset "FDDI-PCI.FDAD-ENG-A-MAN,r=B.11.11.02" (319 | |
| of 723). | |
| * Installing fileset "FDDI-PCI.FDDI4-RUN,r=B.11.11.02" (320 of | |
| 723). | |
| * Installing fileset "GE-DRV.GE-RUN,r=B.11.11.19" (321 of 723). | |
| * Installing fileset "JFS.JFS-ENG-A-MAN,r=B.11.11" (322 of 723). | |
| * Installing fileset "JFS.JFS-JPN-E-MAN,r=B.11.11" (323 of 723). | |
| * Installing fileset "JFS.JFS-JPN-S-MAN,r=B.11.11" (324 of 723). | |
| * Installing fileset "JFS.VXFS-BASE-RUN,r=B.11.11" (325 of 723). | |
| * Installing fileset "JFS.VXFS-PRG,r=B.11.11" (326 of 723). | |
| * Installing fileset "LVM.LVM-ENG-A-MAN,r=B.11.11" (327 of 723). | |
| * Installing fileset "LVM.LVM-JPN-E-MAN,r=B.11.11" (328 of 723). | |
| * Installing fileset "LVM.LVM-JPN-S-MAN,r=B.11.11" (329 of 723). | |
| * Installing fileset "KRB-Support.KRB-SUPP-RUN,r=B.11.11" (330 | |
| of 723). | |
| * Installing fileset "KRB-Support.KRB-SUPP-MAN,r=B.11.11" (331 | |
| of 723). | |
| * Installing fileset "KRB-Support.KRB-SUPP-NOTES,r=B.11.11" (332 | |
| of 723). | |
| * Installing fileset "Update-UX.UUX,r=B.11.11.0509.431" (333 of | |
| 723). | |
| * Installing fileset | |
| "Update-UX.UUX-ENG-A-MAN,r=B.11.11.0509.431" (334 of 723). | |
| * Installing fileset | |
| "Update-UX.UUX-JPN-E-MAN,r=B.11.11.0509.431" (335 of 723). | |
| * Installing fileset | |
| "Update-UX.UUX-JPN-S-MAN,r=B.11.11.0509.431" (336 of 723). | |
| * Installing fileset "ProgSupport.LANG-MIN,r=B.11.11" (337 of | |
| 723). | |
| * Installing fileset "ProgSupport.LANG-64ALIB,r=B.11.11" (338 of | |
| 723). | |
| * Installing fileset "ProgSupport.C-ENG-A-MAN,r=B.11.11" (339 of | |
| 723). | |
| * Installing fileset "ProgSupport.C-JPN-E-MAN,r=B.11.11" (340 of | |
| 723). | |
| * Installing fileset "ProgSupport.C-JPN-S-MAN,r=B.11.11" (341 of | |
| 723). | |
| * Installing fileset "ProgSupport.PAUX-ENG-A-MAN,r=B.11.11" (342 | |
| of 723). | |
| * Installing fileset "ProgSupport.PAUX-JPN-E-MAN,r=B.11.11" (343 | |
| of 723). | |
| * Installing fileset "ProgSupport.PAUX-JPN-S-MAN,r=B.11.11" (344 | |
| of 723). | |
| * Installing fileset "ProgSupport.PMIN-ENG-A-MAN,r=B.11.11" (345 | |
| of 723). | |
| * Installing fileset "ProgSupport.PMIN-JPN-E-MAN,r=B.11.11" (346 | |
| of 723). | |
| * Installing fileset "ProgSupport.PMIN-JPN-S-MAN,r=B.11.11" (347 | |
| of 723). | |
| * Installing fileset "ProgSupport.PROG-AX-64ALIB,r=B.11.11" (348 | |
| of 723). | |
| * Installing fileset "ProgSupport.PROG-MN-64ALIB,r=B.11.11" (349 | |
| of 723). | |
| * Installing fileset "Accounting.ACCOUNTNG,r=B.11.11" (350 of | |
| 723). | |
| * Installing fileset "Accounting.ACCT-ENG-A-MAN,r=B.11.11" (351 | |
| of 723). | |
| * Installing fileset "Accounting.ACCT-JPN-E-MAN,r=B.11.11" (352 | |
| of 723). | |
| * Installing fileset "Accounting.ACCT-JPN-S-MAN,r=B.11.11" (353 | |
| of 723). | |
| * Installing fileset "Asian-Core.ASX-JPN-E-MAN,r=A.03.00" (354 | |
| of 723). | |
| * Installing fileset "Asian-Core.ASX-JPN-MAN,r=A.03.00" (355 of | |
| 723). | |
| * Installing fileset "Asian-Core.ASX-JPN-NOTES,r=A.03.00" (356 | |
| of 723). | |
| * Installing fileset "Asian-Core.ASX-JPN-S-MAN,r=A.03.00" (357 | |
| of 723). | |
| * Installing fileset "Asian-Core.ASX-KOR-NOTES,r=A.03.00" (358 | |
| of 723). | |
| * Installing fileset "Asian-Core.ASX-MAN,r=A.03.00" (359 of | |
| 723). | |
| * Installing fileset "Asian-Core.ASX-SCH-NOTES,r=A.03.00" (360 | |
| of 723). | |
| * Installing fileset "Asian-Core.ASX-TCH-NOTES,r=A.03.00" (361 | |
| of 723). | |
| * Installing fileset "Asian-PRINTER.PRNTR-JPN-RUN,r=A.03.00" | |
| (362 of 723). | |
| * Installing fileset "Asian-PRINTER.PRNTR-KOR-RUN,r=A.03.00" | |
| (363 of 723). | |
| * Installing fileset "Asian-PRINTER.PRNTR-RUN,r=A.03.00" (364 of | |
| 723). | |
| * Installing fileset "Asian-PRINTER.PRNTR-SCH-RUN,r=A.03.00" | |
| (365 of 723). | |
| * Installing fileset "Asian-PRINTER.PRNTR-TCH-RUN,r=A.03.00" | |
| (366 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-LP-JPN-RUN,r=A.03.00" | |
| (367 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-LP-KOR-RUN,r=A.03.00" | |
| (368 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-LP-RUN,r=A.03.00" (369 | |
| of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-LP-SCH-RUN,r=A.03.00" | |
| (370 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-LP-TCH-RUN,r=A.03.00" | |
| (371 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-PD-JPN-RUN,r=A.03.00" | |
| (372 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-PD-KOR-RUN,r=A.03.00" | |
| (373 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-PD-RUN,r=A.03.00" (374 | |
| of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-PD-SCH-RUN,r=A.03.00" | |
| (375 of 723). | |
| * Installing fileset "Asian-PRINTER.PRT-PD-TCH-RUN,r=A.03.00" | |
| (376 of 723). | |
| * Installing fileset "Asian-TERM.IMTERM-RUN,r=A.03.00" (377 of | |
| 723). | |
| * Installing fileset "Asian-TERM.IMTERM-SCH-RUN,r=A.03.00" (378 | |
| of 723). | |
| * Installing fileset "Asian-TERM.IMTERM-TCH-RUN,r=A.03.00" (379 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.EUS-JPN-RUN,r=A.03.00" (380 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.EUS-RUN,r=A.03.00" (381 of | |
| 723). | |
| * Installing fileset "Asian-UTILITY.MFCONV-JPN-RUN,r=A.03.00" | |
| (382 of 723). | |
| * Installing fileset "Asian-UTILITY.STK-SCH-H-MAN,r=A.03.00" | |
| (383 of 723). | |
| * Installing fileset "Asian-UTILITY.STK-SCH-MAN,r=A.03.00" (384 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.STK-SCH-RUN,r=A.03.00" (385 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.TTK-TCH-B-MAN,r=A.03.00" | |
| (386 of 723). | |
| * Installing fileset "Asian-UTILITY.TTK-TCH-C-MAN,r=A.03.00" | |
| (387 of 723). | |
| * Installing fileset "Asian-UTILITY.TTK-TCH-E-MAN,r=A.03.00" | |
| (388 of 723). | |
| * Installing fileset "Asian-UTILITY.TTK-TCH-MAN,r=A.03.00" (389 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.TTK-TCH-RUN,r=A.03.00" (390 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.UDC-JPN-RUN,r=A.03.00" (391 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.UDC-KOR-RUN,r=A.03.00" (392 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.UDC-RUN,r=A.03.00" (393 of | |
| 723). | |
| * Installing fileset "Asian-UTILITY.UDC-SCH-RUN,r=A.03.00" (394 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.UDC-TCH-RUN,r=A.03.00" (395 | |
| of 723). | |
| * Installing fileset "Asian-UTILITY.UTILS-RUN,r=A.03.00" (396 of | |
| 723). | |
| * Installing fileset "Asian-UTILITY.UTILS-SCH-RUN,r=A.03.00" | |
| (397 of 723). | |
| * Installing fileset "Asian-UTILITY.UTILS-TCH-RUN,r=A.03.00" | |
| (398 of 723). | |
| * Installing fileset "CDE.CDE-DTTERM,r=B.11.11" (399 of 723). | |
| * Installing fileset "CDE.CDE-ENG-A-MSG,r=B.11.11" (400 of 723). | |
| * Installing fileset "CDE.CDE-FRE-I-MSG,r=B.11.11" (401 of 723). | |
| * Installing fileset "CDE.CDE-GER-I-MSG,r=B.11.11" (402 of 723). | |
| * Installing fileset "CDE.CDE-ITA-I-MSG,r=B.11.11" (403 of 723). | |
| * Installing fileset "CDE.CDE-JPN-E-MSG,r=B.11.11" (404 of 723). | |
| * Installing fileset "CDE.CDE-JPN-S-MSG,r=B.11.11" (405 of 723). | |
| * Installing fileset "CDE.CDE-KOR-E-MSG,r=B.11.11" (406 of 723). | |
| * Installing fileset "CDE.CDE-SHLIBS,r=B.11.11" (407 of 723). | |
| * Installing fileset "CDE.CDE-TT,r=B.11.11" (408 of 723). | |
| * Installing fileset "CDE.CDE-MIN,r=B.11.11" (409 of 723). | |
| * Installing fileset "CDE.CDE-SCH-H-MSG,r=B.11.11" (410 of 723). | |
| * Installing fileset "CDE.CDE-SPA-I-MSG,r=B.11.11" (411 of 723). | |
| * Installing fileset "CDE.CDE-SWE-I-MSG,r=B.11.11" (412 of 723). | |
| * Installing fileset "CDE.CDE-TCH-B-MSG,r=B.11.11" (413 of 723). | |
| * Installing fileset "CDE.CDE-TCH-E-MSG,r=B.11.11" (414 of 723). | |
| * Installing fileset "CPS.CPS-32SLIB,r=B.11.11" (415 of 723). | |
| * Installing fileset "CPS.CPS-64SLIB,r=B.11.11" (416 of 723). | |
| * Installing fileset "CPS.CPS-MIN,r=B.11.11" (417 of 723). | |
| * Installing fileset "Curses-Color.CURS-ENG-A-MAN,r=B.11.11" | |
| (418 of 723). | |
| * Installing fileset "Curses-Color.CURS-JPN-E-MAN,r=B.11.11" | |
| (419 of 723). | |
| * Installing fileset "Curses-Color.CURS-JPN-S-MAN,r=B.11.11" | |
| (420 of 723). | |
| * Installing fileset "Curses-Color.CURSES-MIN,r=B.11.11" (421 of | |
| 723). | |
| * Installing fileset "Curses-Color.CURSES-PRG,r=B.11.11" (422 of | |
| 723). | |
| * Installing fileset "DiskQuota.DQUO-ENG-A-MAN,r=B.11.11" (423 | |
| of 723). | |
| * Installing fileset "DiskQuota.DQUO-JPN-E-MAN,r=B.11.11" (424 | |
| of 723). | |
| * Installing fileset "DiskQuota.DQUO-JPN-S-MAN,r=B.11.11" (425 | |
| of 723). | |
| * Installing fileset "DiskQuota.DQUOTA,r=B.11.11" (426 of 723). | |
| * Installing fileset "DistributedPrint.PD-CLIENT,r=B.11.11" (427 | |
| of 723). | |
| * Installing fileset "DistributedPrint.PD-COMMON,r=B.11.11" (428 | |
| of 723). | |
| * Installing fileset "DistributedPrint.PD-ENG-A-MAN,r=B.11.11" | |
| (429 of 723). | |
| * Installing fileset "DistributedPrint.PD-JPN-E-MAN,r=B.11.11" | |
| (430 of 723). | |
| * Installing fileset "DistributedPrint.PD-JPN-S-MAN,r=B.11.11" | |
| (431 of 723). | |
| * Installing fileset "DistributedPrint.PD-SERVCOMMON,r=B.11.11" | |
| (432 of 723). | |
| * Installing fileset "DistributedPrint.PD-SPOOLER,r=B.11.11" | |
| (433 of 723). | |
| * Installing fileset "DistributedPrint.PD-SUPERVISOR,r=B.11.11" | |
| (434 of 723). | |
| * Installing fileset "EMS-Core.EMS-CORE,r=A.04.20" (435 of 723). | |
| * Installing fileset "EMS-Core.EMS-MX,r=A.04.20" (436 of 723). | |
| * Installing fileset "EMS-Config.EMS-GUI,r=A.04.20" (437 of | |
| 723). | |
| * Installing fileset "EMS-MIBMonitor.MIBMON-RUN,r=A.04.20" (438 | |
| of 723). | |
| * Installing fileset "GLib.GLIB-MAN,r=1.2.10.9" (439 of 723). | |
| * Installing fileset "GLib.GLIB-NOTES,r=1.2.10.9" (440 of 723). | |
| * Installing fileset "GLib.GLIB-PRG,r=1.2.10.9" (441 of 723). | |
| * Installing fileset "GLib.GLIB-SHLIBS,r=1.2.10.9" (442 of 723). | |
| * Installing fileset "GLib.GLIB-SRC,r=1.2.10.9" (443 of 723). | |
| * Installing fileset "GSS-API.GSS-ENG-A-MAN,r=B.11.11" (444 of | |
| 723). | |
| * Installing fileset "GSS-API.GSS-JPN-E-MAN,r=B.11.11" (445 of | |
| 723). | |
| * Installing fileset "GSS-API.GSS-JPN-S-MAN,r=B.11.11" (446 of | |
| 723). | |
| * Installing fileset "GSS-API.GSSAPI-64SLIB,r=B.11.11" (447 of | |
| 723). | |
| * Installing fileset "GSS-API.GSSAPI-PRG,r=B.11.11" (448 of | |
| 723). | |
| * Installing fileset "GSS-API.GSSAPI-RUN,r=B.11.11" (449 of | |
| 723). | |
| * Installing fileset "GSS-API.GSSAPI-SHLIB,r=B.11.11" (450 of | |
| 723). | |
| * Installing fileset "GTK+.GTK+-MAN,r=1.2.10.9" (451 of 723). | |
| * Installing fileset "GTK+.GTK+-MSG,r=1.2.10.9" (452 of 723). | |
| * Installing fileset "GTK+.GTK+-NOTES,r=1.2.10.9" (453 of 723). | |
| * Installing fileset "GTK+.GTK+-PRG,r=1.2.10.9" (454 of 723). | |
| * Installing fileset "GTK+.GTK+-SHLIBS,r=1.2.10.9" (455 of 723). | |
| * Installing fileset "GTK+.GTK+-SRC,r=1.2.10.9" (456 of 723). | |
| * Installing fileset "Gettext.GETTEXT-MAN,r=0.10.39.9" (457 of | |
| 723). | |
| * Installing fileset "Gettext.GETTEXT-MSG,r=0.10.39.9" (458 of | |
| 723). | |
| * Installing fileset "Gettext.GETTEXT-NOTES,r=0.10.39.9" (459 of | |
| 723). | |
| * Installing fileset "Gettext.GETTEXT-PRG,r=0.10.39.9" (460 of | |
| 723). | |
| * Installing fileset "Gettext.GETTEXT-SHLIBS,r=0.10.39.9" (461 | |
| of 723). | |
| * Installing fileset "Gettext.GETTEXT-SRC,r=0.10.39.9" (462 of | |
| 723). | |
| * Installing fileset "ImagingSubsystem.IMAGE-SHLIBS,r=B.11.11" | |
| (463 of 723). | |
| * Installing fileset "IntegratedLogin.ILOGIN-COMMON,r=B.11.11" | |
| (464 of 723). | |
| * Installing fileset "IntegratedLogin.ILOGIN-DCE,r=B.11.11" (465 | |
| of 723). | |
| * Installing fileset "International.ARABIC,r=B.11.11" (466 of | |
| 723). | |
| * Installing fileset "International.BULGARIAN,r=B.11.11" (467 of | |
| 723). | |
| * Installing fileset "International.CHINESES,r=B.11.11" (468 of | |
| 723). | |
| * Installing fileset "International.CHINESET,r=B.11.11" (469 of | |
| 723). | |
| * Installing fileset "International.CZECH,r=B.11.11" (470 of | |
| 723). | |
| * Installing fileset "International.DANISH,r=B.11.11" (471 of | |
| 723). | |
| * Installing fileset "International.DUTCH,r=B.11.11" (472 of | |
| 723). | |
| * Installing fileset "International.ENGLISH,r=B.11.11" (473 of | |
| 723). | |
| * Installing fileset "International.FINNISH,r=B.11.11" (474 of | |
| 723). | |
| * Installing fileset "International.FRENCH,r=B.11.11" (475 of | |
| 723). | |
| * Installing fileset "International.GERMAN,r=B.11.11" (476 of | |
| 723). | |
| * Installing fileset "International.GREEK,r=B.11.11" (477 of | |
| 723). | |
| * Installing fileset "International.HEBREW,r=B.11.11" (478 of | |
| 723). | |
| * Installing fileset "International.HUNGARIAN,r=B.11.11" (479 of | |
| 723). | |
| * Installing fileset "International.ICELANDIC,r=B.11.11" (480 of | |
| 723). | |
| * Installing fileset "International.ITALIAN,r=B.11.11" (481 of | |
| 723). | |
| * Installing fileset "International.JAPANESE,r=B.11.11" (482 of | |
| 723). | |
| * Installing fileset "International.KOREAN,r=B.11.11" (483 of | |
| 723). | |
| * Installing fileset "International.NORWEGIAN,r=B.11.11" (484 of | |
| 723). | |
| * Installing fileset "International.POLISH,r=B.11.11" (485 of | |
| 723). | |
| * Installing fileset "International.PORTUGUESE,r=B.11.11" (486 | |
| of 723). | |
| * Installing fileset "International.RUMANIAN,r=B.11.11" (487 of | |
| 723). | |
| * Installing fileset "International.RUSSIAN,r=B.11.11" (488 of | |
| 723). | |
| * Installing fileset "International.SERBOCROATIAN,r=B.11.11" | |
| (489 of 723). | |
| * Installing fileset "International.SLOVAKIAN,r=B.11.11" (490 of | |
| 723). | |
| * Installing fileset "International.SLOVENIAN,r=B.11.11" (491 of | |
| 723). | |
| * Installing fileset "International.SPANISH,r=B.11.11" (492 of | |
| 723). | |
| * Installing fileset "International.SWEDISH,r=B.11.11" (493 of | |
| 723). | |
| * Installing fileset "International.THAI,r=B.11.11" (494 of | |
| 723). | |
| * Installing fileset "International.TURKISH,r=B.11.11" (495 of | |
| 723). | |
| * Installing fileset "Judy-lib.JUDY,r=B.11.11.04.13" (496 of | |
| 723). | |
| * Installing fileset "Judy-lib.JUDY-COMMON,r=B.11.11.04.13" (497 | |
| of 723). | |
| * Installing fileset "KRB5-Client.KRB5-64SLIB,r=B.11.11" (498 of | |
| 723). | |
| * Installing fileset "KRB5-Client.KRB5-ENG-A-MAN,r=B.11.11" (499 | |
| of 723). | |
| * Installing fileset "KRB5-Client.KRB5-JPN-E-MAN,r=B.11.11" (500 | |
| of 723). | |
| * Installing fileset "KRB5-Client.KRB5-JPN-S-MAN,r=B.11.11" (501 | |
| of 723). | |
| * Installing fileset "KRB5-Client.KRB5-PRG,r=B.11.11" (502 of | |
| 723). | |
| * Installing fileset "KRB5-Client.KRB5-RUN,r=B.11.11" (503 of | |
| 723). | |
| * Installing fileset "KRB5-Client.KRB5-SHLIB,r=B.11.11" (504 of | |
| 723). | |
| * Installing fileset "Keyshell.KEYS-ENG-A-MAN,r=B.11.11" (505 of | |
| 723). | |
| * Installing fileset "Keyshell.KEYS-JPN-E-MAN,r=B.11.11" (506 of | |
| 723). | |
| * Installing fileset "Keyshell.KEYS-JPN-S-MAN,r=B.11.11" (507 of | |
| 723). | |
| * Installing fileset "Keyshell.KEYSHELL-RUN,r=B.11.11" (508 of | |
| 723). | |
| * Installing fileset "LSSERV.LSRV-ENG-A-MAN,r=B.11.11" (509 of | |
| 723). | |
| * Installing fileset "LSSERV.LSRV-JPN-E-MAN,r=B.11.11" (510 of | |
| 723). | |
| * Installing fileset "LSSERV.LSRV-JPN-S-MAN,r=B.11.11" (511 of | |
| 723). | |
| * Installing fileset "LSSERV.LSSERV-ADMIN,r=B.11.11" (512 of | |
| 723). | |
| * Installing fileset "LSSERV.LSSERV-RUN,r=B.11.11" (513 of 723). | |
| * Installing fileset "LSSERV.LSSERV-SERVER,r=B.11.11" (514 of | |
| 723). | |
| * Installing fileset "LSSERV.LSSERV-SHLIBS,r=B.11.11" (515 of | |
| 723). | |
| * Installing fileset "Libiconv.LICONV-MAN,r=1.6.1.9" (516 of | |
| 723). | |
| * Installing fileset "Libiconv.LICONV-NOTES,r=1.6.1.9" (517 of | |
| 723). | |
| * Installing fileset "Libiconv.LICONV-PRG,r=1.6.1.9" (518 of | |
| 723). | |
| * Installing fileset "Libiconv.LICONV-RUN,r=1.6.1.9" (519 of | |
| 723). | |
| * Installing fileset "Libiconv.LICONV-SHLIBS,r=1.6.1.9" (520 of | |
| 723). | |
| * Installing fileset "Libiconv.LICONV-SRC,r=1.6.1.9" (521 of | |
| 723). | |
| * Installing fileset "MSDOS-Utils.DOS-UTILS,r=B.11.11" (522 of | |
| 723). | |
| * Installing fileset "MSDOS-Utils.DOSU-ENG-A-MAN,r=B.11.11" (523 | |
| of 723). | |
| * Installing fileset "MSDOS-Utils.DOSU-JPN-E-MAN,r=B.11.11" (524 | |
| of 723). | |
| * Installing fileset "MSDOS-Utils.DOSU-JPN-S-MAN,r=B.11.11" (525 | |
| of 723). | |
| * Installing fileset "MailUtilities.MAIL-ENG-A-MAN,r=B.11.11" | |
| (526 of 723). | |
| * Installing fileset "MailUtilities.MAIL-JPN-E-MAN,r=B.11.11" | |
| (527 of 723). | |
| * Installing fileset "MailUtilities.MAIL-JPN-S-MAN,r=B.11.11" | |
| (528 of 723). | |
| * Installing fileset "MailUtilities.MAILERS,r=B.11.11" (529 of | |
| 723). | |
| * Installing fileset "Mozilla.MOZ-COM,r=1.7.8.00.00" (530 of | |
| 723). | |
| * Installing fileset "Mozilla.MOZ-COM-DOC,r=1.7.8.00.00" (531 of | |
| 723). | |
| * Installing fileset "Mozilla.MOZ-PA11,r=1.7.8.00.00" (532 of | |
| 723). | |
| * Installing fileset "MozillaSrc.MOZ-SRC,r=1.7.8.00.00" (533 of | |
| 723). | |
| * Installing fileset "openssl.OPENSSL-SRC,r=A.00.09.07e.012" | |
| (534 of 723). | |
| * Installing fileset "openssl.OPENSSL-RUN,r=A.00.09.07e.012" | |
| (535 of 723). | |
| * Installing fileset "openssl.OPENSSL-PVT,r=A.00.09.07e.012" | |
| (536 of 723). | |
| * Installing fileset "openssl.OPENSSL-PRNG,r=A.00.09.07e.012" | |
| (537 of 723). | |
| * Installing fileset "openssl.OPENSSL-MIS,r=A.00.09.07e.012" | |
| (538 of 723). | |
| * Installing fileset "openssl.OPENSSL-MAN,r=A.00.09.07e.012" | |
| (539 of 723). | |
| * Installing fileset "openssl.OPENSSL-LIB,r=A.00.09.07e.012" | |
| (540 of 723). | |
| * Installing fileset "openssl.OPENSSL-INC,r=A.00.09.07e.012" | |
| (541 of 723). | |
| * Installing fileset "openssl.OPENSSL-DOC,r=A.00.09.07e.012" | |
| (542 of 723). | |
| * Installing fileset "openssl.OPENSSL-CONF,r=A.00.09.07e.012" | |
| (543 of 723). | |
| * Installing fileset "openssl.OPENSSL-CER,r=A.00.09.07e.012" | |
| (544 of 723). | |
| * Installing fileset "WBEMServices.WBEM-CORE,r=A.02.00.07" (545 | |
| of 723). | |
| * Installing fileset "WBEMServices.WBEM-CORE-COM,r=A.02.00.07" | |
| (546 of 723). | |
| * Installing fileset "WBEMServices.WBEM-MAN,r=A.02.00.07" (547 | |
| of 723). | |
| * Installing fileset "WBEMServices.WBEM-MX,r=A.02.00.07" (548 of | |
| 723). | |
| * Installing fileset | |
| "NParProvider.NPAR-DOC,r=B.11.11.01.04.01.01" (549 of 723). | |
| * Installing fileset | |
| "NParProvider.NPAR-RUN,r=B.11.11.01.04.01.01" (550 of 723). | |
| * Installing fileset "NonHP-Terminfo.NONHPTERM,r=B.11.11" (551 | |
| of 723). | |
| * Installing fileset "OBAM.OBAM-BIN,r=B.11.00.05.3.06" (552 of | |
| 723). | |
| * Installing fileset "OBAM.OBAM-JVM,r=B.11.00.05.3.06" (553 of | |
| 723). | |
| * Installing fileset "OBAM.OBAM-WEB,r=B.11.00.05.3.06" (554 of | |
| 723). | |
| * Installing fileset "PHCO_22958.FIRST-BOOT,r=1.0" (555 of 723). | |
| * Installing fileset "PHCO_23263.ADMN-ENG-A-MAN,r=B.11.11.15" | |
| (556 of 723). | |
| * Installing fileset "PHCO_23263.ARRAY-MGMT,r=B.11.11.15" (557 | |
| of 723). | |
| * Installing fileset "PHCO_24173.ADMN-ENG-A-MAN,r=1.0" (558 of | |
| 723). | |
| * Installing fileset "PHCO_24173.UPS-TOOLS,r=1.0" (559 of 723). | |
| * Installing fileset "PHCO_25311.ADMN-ENG-A-MAN,r=B.11.11.15" | |
| (560 of 723). | |
| * Installing fileset "PHCO_25311.ARRAY-MGMT,r=B.11.11.15" (561 | |
| of 723). | |
| * Installing fileset "PHCO_25831.UX-CORE,r=1.0" (562 of 723). | |
| * Installing fileset "PHCO_26951.UX-CORE,r=1.0" (563 of 723). | |
| * Installing fileset "PHCO_27100.UX-CORE,r=1.0" (564 of 723). | |
| * Installing fileset "PHCO_27101.ADMN-ENG-A-MAN,r=1.0" (565 of | |
| 723). | |
| * Installing fileset "PHCO_27101.KERN-ENG-A-MAN,r=1.0" (566 of | |
| 723). | |
| * Installing fileset "PHCO_27101.KERN-RUN,r=1.0" (567 of 723). | |
| * Installing fileset "PHCO_27101.UX-CORE,r=1.0" (568 of 723). | |
| * Installing fileset "PHCO_27185.UX-CORE,r=1.0" (569 of 723). | |
| * Installing fileset "PHCO_27758.CORE-SHLIBS,r=1.0" (570 of | |
| 723). | |
| * Installing fileset "PHCO_28160.UX-CORE,r=1.0" (571 of 723). | |
| * Installing fileset "PHCO_28169.UX-CORE,r=1.0" (572 of 723). | |
| * Installing fileset "PHCO_28998.SYS-ADMIN,r=1.0" (573 of 723). | |
| * Installing fileset "PHCO_28998.UX-CORE,r=1.0" (574 of 723). | |
| * Installing fileset "PHCO_29379.LVM-ENG-A-MAN,r=1.0" (575 of | |
| 723). | |
| * Installing fileset "PHCO_29379.LVM-RUN,r=1.0" (576 of 723). | |
| * Installing fileset "PHCO_30514.ADMN-ENG-A-MAN,r=1.0" (577 of | |
| 723). | |
| * Installing fileset "PHCO_30514.CORE-SHLIBS,r=1.0" (578 of | |
| 723). | |
| * Installing fileset "PHCO_30514.UX-CORE,r=1.0" (579 of 723). | |
| * Installing fileset "PHCO_30598.INETSVCS-BOOT,r=1.0" (580 of | |
| 723). | |
| * Installing fileset "PHCO_30598.SAM,r=1.0" (581 of 723). | |
| * Installing fileset "PHCO_30598.SAM-ENG-A-MAN,r=1.0" (582 of | |
| 723). | |
| * Installing fileset "PHCO_30598.SAM-HELP,r=1.0" (583 of 723). | |
| * Installing fileset "PHCO_30598.UX-CORE,r=1.0" (584 of 723). | |
| * Installing fileset "PHCO_31878.CORE-ENG-A-MAN,r=1.0" (585 of | |
| 723). | |
| * Installing fileset "PHCO_31878.SYS-ADMIN,r=1.0" (586 of 723). | |
| * Installing fileset "PHKL_23298.KERN-DEV-KIT,r=1.0" (587 of | |
| 723). | |
| * Installing fileset "PHKL_23300.KERN-DEV-KIT,r=1.0" (588 of | |
| 723). | |
| * Installing fileset "PHKL_27177.ADMN-ENG-A-MAN,r=1.0" (589 of | |
| 723). | |
| * Installing fileset "PHKL_27177.KERN-RUN,r=1.0" (590 of 723). | |
| NOTE: Successfully updated disk /dev/dsk/c0t0d0. | |
| * Installing fileset "PHNE_23289.C-INC,r=1.0" (591 of 723). | |
| * Installing fileset "PHSS_22898.CORE-64SLIB,r=1.0" (592 of | |
| 723). | |
| * Installing fileset "PHSS_22898.CORE-SHLIBS,r=1.0" (593 of | |
| 723). | |
| * Installing fileset "PHSS_22898.LANG-64ALIB,r=1.0" (594 of | |
| 723). | |
| * Installing fileset "PHSS_22898.LANG-MIN,r=1.0" (595 of 723). | |
| * Installing fileset "PHSS_25983.KERN-RUN,r=1.0" (596 of 723). | |
| * Installing fileset "Xserver.XEXT-RECORD,r=B.11.11" (597 of | |
| 723). | |
| * Installing fileset "Xserver.XEXT-MBX,r=B.11.11" (598 of 723). | |
| * Installing fileset "Xserver.XEXT-HPCR-MAN,r=B.11.11" (599 of | |
| 723). | |
| * Installing fileset "Xserver.XEXT-HPCR,r=B.11.11" (600 of 723). | |
| * Installing fileset "Xserver.XEXT-DPMS-MAN,r=B.11.11" (601 of | |
| 723). | |
| * Installing fileset "Xserver.XEXT-DPMS,r=B.11.11" (602 of 723). | |
| * Installing fileset "Xserver.XEXT-DBE-MAN,r=B.11.11" (603 of | |
| 723). | |
| * Installing fileset "Xserver.XEXT-DBE,r=B.11.11" (604 of 723). | |
| * Installing fileset "Xserver.X11-SERV-MAN,r=B.11.11" (605 of | |
| 723). | |
| * Installing fileset "Xserver.X11-SERV,r=B.11.11" (606 of 723). | |
| NOTE: copying /usr/newconfig/usr/lib/X11/extensions/libSX.1 to | |
| /usr/lib/X11/extensions/libSX.1 | |
| * Installing fileset "Xserver.DDX-UTILS,r=B.11.11" (607 of 723). | |
| * Installing fileset "Xserver.DDX-SLS,r=B.11.11" (608 of 723). | |
| * Installing fileset "Xserver.DDX-SAM,r=B.11.11" (609 of 723). | |
| * Installing fileset "Xserver.DDX-LOAD,r=B.11.11" (610 of 723). | |
| * Installing fileset "Xserver.DDX-ENTRY,r=B.11.11" (611 of 723). | |
| * Installing fileset "Xserver.DDX-ADVANCED,r=B.11.11" (612 of | |
| 723). | |
| * Installing fileset "Xserver.AGRM,r=B.11.11" (613 of 723). | |
| * Installing fileset "X11.X11R6-SHLIBS,r=B.11.11" (614 of 723). | |
| * Installing fileset "X11.X11R5-SHLIBS,r=B.11.11" (615 of 723). | |
| * Installing fileset "X11.MKFONTDIR,r=B.11.11" (616 of 723). | |
| * Installing fileset "X11.MOTIF-SHLIB,r=B.11.11" (617 of 723). | |
| * Installing fileset "X11.X11-FONT-AUX,r=B.11.11" (618 of 723). | |
| NOTE: See /tmp/X11_newfonts.log for more information on newly | |
| installed fonts | |
| * Installing fileset "X11.X11-FONT-MIN,r=B.11.11" (619 of 723). | |
| NOTE: See /tmp/X11_newfonts.log for more information on newly | |
| installed fonts | |
| * Installing fileset "X11.X11-FONTSRV,r=B.11.11" (620 of 723). | |
| * Installing fileset "X11.X11-FRE-I-MSG,r=B.11.11" (621 of 723). | |
| * Installing fileset "X11.X11-GER-I-MSG,r=B.11.11" (622 of 723). | |
| * Installing fileset "X11.X11-ITA-I-MSG,r=B.11.11" (623 of 723). | |
| * Installing fileset "X11.X11-JPN-E-MSG,r=B.11.11" (624 of 723). | |
| * Installing fileset "X11.X11-JPN-S-MSG,r=B.11.11" (625 of 723). | |
| * Installing fileset "X11.X11-KOR-E-MSG,r=B.11.11" (626 of 723). | |
| * Installing fileset "X11.X11-RUN,r=B.11.11" (627 of 723). | |
| * Installing fileset "X11.X11-RUN-CL,r=B.11.11" (628 of 723). | |
| * Installing fileset "X11.X11-RUN-CL-MAN,r=B.11.11" (629 of | |
| 723). | |
| * Installing fileset "X11.X11-RUN-CT-MAN,r=B.11.11" (630 of | |
| 723). | |
| * Installing fileset "X11.X11-RUN-CTRB,r=B.11.11" (631 of 723). | |
| * Installing fileset "X11.X11-RUN-MAN,r=B.11.11" (632 of 723). | |
| * Installing fileset "X11.X11-SCH-H-MSG,r=B.11.11" (633 of 723). | |
| * Installing fileset "X11.X11-SPA-I-MSG,r=B.11.11" (634 of 723). | |
| * Installing fileset "X11.X11-SWE-I-MSG,r=B.11.11" (635 of 723). | |
| * Installing fileset "X11.X11-TCH-B-MSG,r=B.11.11" (636 of 723). | |
| * Installing fileset "X11.X11-TCH-E-MSG,r=B.11.11" (637 of 723). | |
| * Installing fileset "X11.X11R4-SHLIBS,r=B.11.11" (638 of 723). | |
| * Installing fileset "PHSS_32939.AGRM,r=B.11.11.29" (639 of | |
| 723). | |
| * Installing fileset "PHSS_32939.DDX-ADVANCED,r=B.11.11.29" (640 | |
| of 723). | |
| * Installing fileset "PHSS_32939.DDX-ENTRY,r=B.11.11.29" (641 of | |
| 723). | |
| * Installing fileset "PHSS_32939.DDX-LOAD,r=B.11.11.29" (642 of | |
| 723). | |
| * Installing fileset "PHSS_32939.DDX-SAM,r=B.11.11.29" (643 of | |
| 723). | |
| * Installing fileset "PHSS_32939.DDX-SLS,r=B.11.11.29" (644 of | |
| 723). | |
| * Installing fileset "PHSS_32939.DDX-UTILS,r=B.11.11.29" (645 of | |
| 723). | |
| * Installing fileset "PHSS_32939.X11-SERV,r=B.11.11.29" (646 of | |
| 723). | |
| * Installing fileset "PHSS_32939.X11-SERV-MAN,r=B.11.11.29" (647 | |
| of 723). | |
| * Installing fileset "PHSS_32939.XEXT-DBE,r=B.11.11.29" (648 of | |
| 723). | |
| * Installing fileset "PHSS_32939.XEXT-DBE-MAN,r=B.11.11.29" (649 | |
| of 723). | |
| * Installing fileset "PHSS_32939.XEXT-DPMS,r=B.11.11.29" (650 of | |
| 723). | |
| * Installing fileset "PHSS_32939.XEXT-DPMS-MAN,r=B.11.11.29" | |
| (651 of 723). | |
| * Installing fileset "PHSS_32939.XEXT-HPCR,r=B.11.11.29" (652 of | |
| 723). | |
| * Installing fileset "PHSS_32939.XEXT-HPCR-MAN,r=B.11.11.29" | |
| (653 of 723). | |
| * Installing fileset "PHSS_32939.XEXT-MBX,r=B.11.11.29" (654 of | |
| 723). | |
| * Installing fileset "PHSS_32939.XEXT-RECORD,r=B.11.11.29" (655 | |
| of 723). | |
| * Installing fileset "PrinterMgmt.LP-SPOOL,r=B.11.11" (656 of | |
| 723). | |
| * Installing fileset "PrinterMgmt.LPSP-ENG-A-MAN,r=B.11.11" (657 | |
| of 723). | |
| * Installing fileset "PrinterMgmt.LPSP-JPN-E-MAN,r=B.11.11" (658 | |
| of 723). | |
| * Installing fileset "PrinterMgmt.LPSP-JPN-S-MAN,r=B.11.11" (659 | |
| of 723). | |
| * Installing fileset "SOE.SOE,r=B.11.11" (660 of 723). | |
| * Installing fileset "SOE.SOE-ENG-A-MAN,r=B.11.11" (661 of 723). | |
| * Installing fileset "SOE.SOE-JPN-E-MAN,r=B.11.11" (662 of 723). | |
| * Installing fileset "SOE.SOE-JPN-S-MAN,r=B.11.11" (663 of 723). | |
| * Installing fileset "SecurityMon.AUDT-ENG-A-MAN,r=B.11.11" (664 | |
| of 723). | |
| * Installing fileset "SecurityMon.AUDT-JPN-E-MAN,r=B.11.11" (665 | |
| of 723). | |
| * Installing fileset "SecurityMon.AUDT-JPN-S-MAN,r=B.11.11" (666 | |
| of 723). | |
| * Installing fileset "SecurityMon.SEC-ENG-A-MAN,r=B.11.11" (667 | |
| of 723). | |
| * Installing fileset "SecurityMon.SEC-JPN-E-MAN,r=B.11.11" (668 | |
| of 723). | |
| * Installing fileset "SecurityMon.SEC-JPN-S-MAN,r=B.11.11" (669 | |
| of 723). | |
| * Installing fileset "SecurityMon.SECURITY,r=B.11.11" (670 of | |
| 723). | |
| NOTE: Newly delivered files /tcb/files/devassign /tcb/files/ttys and | |
| /tcb/files/auth/system/default are present under | |
| /usr/newconfig/tcb. | |
| * Installing fileset "SourceControl.SRC-CNTL,r=B.11.11" (671 of | |
| 723). | |
| * Installing fileset "SourceControl.SRC-ENG-A-MAN,r=B.11.11" | |
| (672 of 723). | |
| * Installing fileset "SourceControl.SRC-JPN-E-MAN,r=B.11.11" | |
| (673 of 723). | |
| * Installing fileset "SourceControl.SRC-JPN-S-MAN,r=B.11.11" | |
| (674 of 723). | |
| * Installing fileset "Spelling.SPEL-ENG-A-MAN,r=B.11.11" (675 of | |
| 723). | |
| * Installing fileset "Spelling.SPEL-JPN-E-MAN,r=B.11.11" (676 of | |
| 723). | |
| * Installing fileset "Spelling.SPEL-JPN-S-MAN,r=B.11.11" (677 of | |
| 723). | |
| * Installing fileset "Spelling.SPELL,r=B.11.11" (678 of 723). | |
| * Installing fileset "SystemComm.SYSC-ENG-A-MAN,r=B.11.11" (679 | |
| of 723). | |
| * Installing fileset "SystemComm.SYSC-JPN-E-MAN,r=B.11.11" (680 | |
| of 723). | |
| * Installing fileset "SystemComm.SYSC-JPN-S-MAN,r=B.11.11" (681 | |
| of 723). | |
| * Installing fileset "SystemComm.SYSCOM,r=B.11.11" (682 of 723). | |
| * Installing fileset "TerminalMngr.TERM-ENG-A-MAN,r=B.11.11" | |
| (683 of 723). | |
| * Installing fileset "TerminalMngr.TERM-JPN-E-MAN,r=B.11.11" | |
| (684 of 723). | |
| * Installing fileset "TerminalMngr.TERM-JPN-S-MAN,r=B.11.11" | |
| (685 of 723). | |
| * Installing fileset "TerminalMngr.TERM-MNGR-MIN,r=B.11.11" (686 | |
| of 723). | |
| * Installing fileset "TerminalMngr.TERM-MNGR-NHP,r=B.11.11" (687 | |
| of 723). | |
| * Installing fileset "TerminalMngr.TSM-FRE-I-MSG,r=B.11.11" (688 | |
| of 723). | |
| * Installing fileset "TerminalMngr.TSM-GER-I-MSG,r=B.11.11" (689 | |
| of 723). | |
| * Installing fileset "TextEditors.EDIT-ENG-A-MAN,r=B.11.11" (690 | |
| of 723). | |
| * Installing fileset "TextEditors.EDIT-JPN-E-MAN,r=B.11.11" (691 | |
| of 723). | |
| * Installing fileset "TextEditors.EDIT-JPN-S-MAN,r=B.11.11" (692 | |
| of 723). | |
| * Installing fileset "TextEditors.EDITORS,r=B.11.11" (693 of | |
| 723). | |
| * Installing fileset "UUCP.UUCP,r=B.11.11" (694 of 723). | |
| * Installing fileset "UUCP.UUCP-ENG-A-MAN,r=B.11.11" (695 of | |
| 723). | |
| * Installing fileset "UUCP.UUCP-JPN-E-MAN,r=B.11.11" (696 of | |
| 723). | |
| * Installing fileset "UUCP.UUCP-JPN-S-MAN,r=B.11.11" (697 of | |
| 723). | |
| * Installing fileset "iCOD.ICOD-RUN,r=B.11.11.07.01.00.00" (698 | |
| of 723). | |
| * Installing fileset "iCOD.ICOD-COMMON,r=B.11.11.07.01.00.00" | |
| (699 of 723). | |
| * Installing fileset "iCOD.ICOD-ENG-A-MAN,r=B.11.11.07.01.00.00" | |
| (700 of 723). | |
| * Installing fileset "iCOD.ICOD-FCA-I-MSG,r=B.11.11.07.01.00.00" | |
| (701 of 723). | |
| * Installing fileset "iCOD.ICOD-FCA-U-MSG,r=B.11.11.07.01.00.00" | |
| (702 of 723). | |
| * Installing fileset "iCOD.ICOD-FRE-I-MSG,r=B.11.11.07.01.00.00" | |
| (703 of 723). | |
| * Installing fileset "iCOD.ICOD-FRE-U-MSG,r=B.11.11.07.01.00.00" | |
| (704 of 723). | |
| * Installing fileset "iCOD.ICOD-GER-I-MSG,r=B.11.11.07.01.00.00" | |
| (705 of 723). | |
| * Installing fileset "iCOD.ICOD-GER-U-MSG,r=B.11.11.07.01.00.00" | |
| (706 of 723). | |
| * Installing fileset "iCOD.ICOD-HKG-U-MSG,r=B.11.11.07.01.00.00" | |
| (707 of 723). | |
| * Installing fileset "iCOD.ICOD-ITA-I-MSG,r=B.11.11.07.01.00.00" | |
| (708 of 723). | |
| * Installing fileset "iCOD.ICOD-ITA-U-MSG,r=B.11.11.07.01.00.00" | |
| (709 of 723). | |
| * Installing fileset "iCOD.ICOD-JPN-E-MAN,r=B.11.11.07.01.00.00" | |
| (710 of 723). | |
| * Installing fileset "iCOD.ICOD-JPN-E-MSG,r=B.11.11.07.01.00.00" | |
| (711 of 723). | |
| * Installing fileset "iCOD.ICOD-JPN-S-MAN,r=B.11.11.07.01.00.00" | |
| (712 of 723). | |
| * Installing fileset "iCOD.ICOD-JPN-S-MSG,r=B.11.11.07.01.00.00" | |
| (713 of 723). | |
| * Installing fileset "iCOD.ICOD-JPN-U-MSG,r=B.11.11.07.01.00.00" | |
| (714 of 723). | |
| * Installing fileset "iCOD.ICOD-KOR-E-MSG,r=B.11.11.07.01.00.00" | |
| (715 of 723). | |
| * Installing fileset "iCOD.ICOD-KOR-U-MSG,r=B.11.11.07.01.00.00" | |
| (716 of 723). | |
| * Installing fileset "iCOD.ICOD-SCH-H-MSG,r=B.11.11.07.01.00.00" | |
| (717 of 723). | |
| * Installing fileset "iCOD.ICOD-SCH-U-MSG,r=B.11.11.07.01.00.00" | |
| (718 of 723). | |
| * Installing fileset "iCOD.ICOD-SPA-I-MSG,r=B.11.11.07.01.00.00" | |
| (719 of 723). | |
| * Installing fileset "iCOD.ICOD-SPA-U-MSG,r=B.11.11.07.01.00.00" | |
| (720 of 723). | |
| * Installing fileset "iCOD.ICOD-TCH-B-MSG,r=B.11.11.07.01.00.00" | |
| (721 of 723). | |
| * Installing fileset "iCOD.ICOD-TCH-E-MSG,r=B.11.11.07.01.00.00" | |
| (722 of 723). | |
| * Installing fileset "iCOD.ICOD-TCH-U-MSG,r=B.11.11.07.01.00.00" | |
| (723 of 723). | |
| * Running install clean command /usr/lbin/sw/install_clean. | |
| NOTE: tlremove is searching filesystem - please be patient | |
| NOTE: Successfully completed | |
| NOTE: tlinstall is searching filesystem - please be patient | |
| NOTE: Successfully completed | |
| * Summary of Execution Phase: | |
| * 26 of 749 filesets were Skipped. | |
| * 723 of 749 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/03/19 00:31:36 EST END install AGENT SESSION (pid=143) | |
| (jobid=loopback-0001) | |
| * Software installation of this source (B7994 11i Mission Critical OE: | |
| CD1) is complete. | |
| ======================================================================= | |
| USER INTERACTION REQUIRED: | |
| To complete the installation you must now insert the | |
| "B7994 11i Mission Critical OE: CD2" CD. | |
| Once this is done, press the <Return> key to continue: | |
| * Starting swinstall of the source (B7994 11i Mission Critical OE: CD2). | |
| * Running command: "/usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM | |
| -f/tmp/ign_configure/software_file -x os_release=B.11.11 -x | |
| os_name=HP-UX:32 -xpatch_filter=*.* -xpatch_save_files=true " | |
| ======= 11/03/19 06:00:53 EST BEGIN install AGENT SESSION (pid=6109) | |
| (jobid=loopback-0002) | |
| * Agent session started for user "root@localhost". (pid=6109) | |
| NOTE: The software item "CDE-ChineseS" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "Asian-X11.IMX11-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "Asian-X11.IMX11-SCH-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 CDE.CDE-SCH-H-MSG,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-SCH-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "AudioSubsystem.AUD-ENG-A-MAN,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| TextFormatters.TEXT-FMT,r>=B.11.11.%27 | |
| * The software | |
| "AudioSubsystem.AUD-SCH-H-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.CHINESES,r>=B.11.11.%27 | |
| * The software | |
| "AudioSubsystem.AUDIO-RUN,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MOTIF-SHLIB,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-RUN,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-SCH-H-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.CHINESES,r>=B.11.11.%27 | |
| * The software | |
| "DesktopConfig.LITECONFIG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| OS-Core.CORE-KRN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-RUN,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-SCH-H-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-ChineseT" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "Asian-X11.IMX11-TCH-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 CDE.CDE-TCH-B-MSG,r>=B.11.11.% | |
| CDE.CDE-TCH-E-MSG,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-TCH-B-AUX,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-TCH-B-MIN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-TCH-C-AUX,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-TCH-C-MIN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-TCH-E-AUX,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-TCH-E-MIN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "AudioSubsystem.AUD-TCH-B-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.CHINESET,r>=B.11.11.%27 | |
| * The software | |
| "AudioSubsystem.AUD-TCH-E-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.CHINESET,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-TCH-B-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.CHINESET,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-TCH-E-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.CHINESET,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-TCH-B-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-TCH-E-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-English" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "VUEtoCDE.V2C-ENG-A-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-French" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "AudioSubsystem.AUD-FRE-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.FRENCH,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-FRE-I-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: International.FRENCH,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-FRE-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-German" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "AudioSubsystem.AUD-GER-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.GERMAN,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-GER-I-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: International.GERMAN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-GER-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-Italian" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "AudioSubsystem.AUD-ITA-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.ITALIAN,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-ITA-I-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.ITALIAN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-ITA-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-Japanese" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "Asian-X11.IMX11-JPN-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| InternetSrvcs.INETSVCS-INETD,r>=B.11.11.% | |
| CDE.CDE-MIN,r>=B.11.11.%27 CDE.CDE-JPN-S-MSG,r>=B.11.11.% | |
| CDE.CDE-JPN-E-MSG,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-JPN-AUX,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-JPN-MIN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XJIM-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: CDE.CDE-MIN,r>=B.11.11.%27 | |
| InternetSrvcs.INETSVCS-INETD,r>=B.11.11.% | |
| CDE.CDE-JPN-S-MSG,r>=B.11.11.% CDE.CDE-JPN-E-MSG,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XP-JPN-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11FONTSRV.TT-JPN-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.X11-FONTSRV,r>=B.11.11.% X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "AudioSubsystem.AUD-JPN-E-MAN,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| TextFormatters.TEXT-FMT,r>=B.11.11.%27 | |
| * The software | |
| "AudioSubsystem.AUD-JPN-E-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.JAPANESE,r>=B.11.11.%27 | |
| * The software | |
| "AudioSubsystem.AUD-JPN-S-MAN,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| TextFormatters.TEXT-FMT,r>=B.11.11.%27 | |
| * The software | |
| "AudioSubsystem.AUD-JPN-S-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.JAPANESE,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-JPN-E-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.JAPANESE,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-JPN-S-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.JAPANESE,r>=B.11.11.%27 | |
| * The software | |
| "EGBridge.EGB-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| InternetSrvcs.INETSVCS-INETD,r>=B.11.11.% | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "VJE.VJE-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| InternetSrvcs.INETSVCS-INETD,r>=B.11.11.% | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-JPN-E-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-JPN-S-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| * The software | |
| "ATOK.ATOK-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-Korean" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "Asian-X11.IMX11-KOR-RUN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 CDE.CDE-KOR-E-MSG,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-KOR-AUX,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-KOR-BOLD,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "Asian-X11.XFNT-KOR-MIN,r=A.03.00,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| X11.MKFONTDIR,r>=B.11.11.% | |
| * The software | |
| "AudioSubsystem.AUD-KOR-E-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.KOREAN,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-KOR-E-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: International.KOREAN,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-KOR-E-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-Spanish" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "AudioSubsystem.AUD-SPA-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.SPANISH,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-SPA-I-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.SPANISH,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-SPA-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "CDE-Swedish" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "AudioSubsystem.AUD-SWE-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| International.SWEDISH,r>=B.11.11.%27 | |
| * The software | |
| "CDE.CDE-SWE-I-HELP,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| International.SWEDISH,r>=B.11.11.%27 | |
| * The software | |
| "VUEtoCDE.V2C-SWE-I-MSG,r=B.11.11,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| CDE.CDE-MIN,r>=B.11.11.%27 | |
| NOTE: The software item "OnlineDiag" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "Sup-Tool-Mgr.STM-UI-RUN,r=B.11.11.16.09,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: X11.X11R6-SHLIBS | |
| X11.MOTIF-SHLIB SystemAdmin.SAM | |
| * The software | |
| "EMS-Config.EMS-GUI,r=A.04.20,a=HP-UX_B.11.00_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: SystemAdmin.SAM | |
| WARNING: The software specified contains a fileset that changes the | |
| kernel. Either the attribute dynamic_module, used for dynamic | |
| changes, is specified, or the is_kernel attribute, used for | |
| static changes, is set to true. | |
| * Beginning Analysis Phase. | |
| * Source: localhost:/tmp/ign_configure/SD_CDROM | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for product information. | |
| NOTE: The filesystems in the filesystem table will not be checked | |
| against those currently mounted because the | |
| "mount_all_filesystems" option is set to "false". | |
| NOTE: The fileset "EMS-Core.EMS-CORE,r=A.04.20" is already | |
| installed. If you wish to reinstall this fileset, change the | |
| "reinstall" option to "true". | |
| NOTE: The fileset "EMS-Core.EMS-MX,r=A.04.20" is already installed. | |
| If you wish to reinstall this fileset, change the "reinstall" | |
| option to "true". | |
| NOTE: The fileset "EMS-Config.EMS-GUI,r=A.04.20" is already | |
| installed. If you wish to reinstall this fileset, change the | |
| "reinstall" option to "true". | |
| * Reading source for file information. | |
| NOTE: Cannot safely install "DesktopConfig" onto the system because | |
| "NFS.NIS-SERVER" is already installed. To correct this problem, you | |
| must remove "NFS.NIS-SERVER" from the system and then retry. | |
| NOTE: Cannot safely install "DesktopConfig" onto the system because | |
| "X11.X11-FONTSRV" is already installed. To correct this problem, you | |
| must remove "X11.X11-FONTSRV" from the system and then retry. | |
| NOTE: "DesktopConfig" is generally only intended for use with single-user | |
| Series 700 systems installed with the "Desktop HP-UX" product. | |
| Installing it will result in a kernel that is built with a reduced | |
| (minimal) set of kernel tunable parameters appropriate for only | |
| single-user desktop environments. See the on-line swinstall product | |
| descriptions of "DesktopConfig". | |
| If you still wish to install "DesktopConfig", then correct the | |
| problem(s) shown above and install it again, -or- run the SAM | |
| utility and select the "Apply Lite HP-UX Configuration" Action from | |
| within any of SAM's Kernel Configuration screens. | |
| NOTE: The "checkinstall" script for "DesktopConfig.LITECONFIG" gave | |
| an "exclude" return (exit code "3"). The script location was | |
| "/var/tmp/BAAa06109/catalog/DesktopConfig/LITECONFIG/checkinstall". | |
| NOTE: This software will be excluded from further processing. | |
| * Executing preDSA command. | |
| NOTE: The used disk space on filesystem "/" is estimated to increase | |
| by 824 Kbytes. | |
| This will leave 163904 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/usr" is estimated to | |
| increase by 389232 Kbytes. | |
| This will leave 1164752 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/var" is estimated to | |
| increase by 18424 Kbytes. | |
| This will leave 1420504 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/opt" is estimated to | |
| increase by 97248 Kbytes. | |
| This will leave 2061104 Kbytes of available user disk space | |
| after the installation. | |
| * Summary of Analysis Phase: | |
| * 4 of 124 filesets will be Skipped. | |
| * 120 of 124 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Install Execution Phase. | |
| * Filesets: 120 | |
| * Files: 14307 | |
| * Kbytes: 436404 | |
| * Installing bundle "CDE-ChineseS,r=B.11.11.0412" . | |
| * Installing bundle "CDE-ChineseT,r=B.11.11.0412" . | |
| * Installing bundle "CDE-English,r=B.11.11.0412" . | |
| * Installing bundle "CDE-French,r=B.11.11.0412" . | |
| * Installing bundle "CDE-German,r=B.11.11.0412" . | |
| * Installing bundle "CDE-Italian,r=B.11.11.0412" . | |
| * Installing bundle "CDE-Japanese,r=B.11.11.0412" . | |
| * Installing bundle "CDE-Korean,r=B.11.11.0412" . | |
| * Installing bundle "CDE-Spanish,r=B.11.11.0412" . | |
| * Installing bundle "CDE-Swedish,r=B.11.11.0412" . | |
| * Installing bundle "J4269AA,r=B.04.00.02" . | |
| * Installing bundle "OnlineDiag,r=B.11.11.16.09" . | |
| * Installing bundle "T1456AAaddon,r=1.4.2.09.02" . | |
| * Installing bundle "T1457AAaddon,r=1.4.2.09.02" . | |
| * Installing fileset "CDE.CDE-RUN,r=B.11.11" (1 of 120). | |
| * Installing fileset "CDE.CDE-ENG-A-HELP,r=B.11.11" (2 of 120). | |
| * Installing fileset "CDE.CDE-ENG-A-MAN,r=B.11.11" (3 of 120). | |
| * Installing fileset "CDE.CDE-FONTS,r=B.11.11" (4 of 120). | |
| * Installing fileset "CDE.CDE-FRE-I-HELP,r=B.11.11" (5 of 120). | |
| * Installing fileset "CDE.CDE-GER-I-HELP,r=B.11.11" (6 of 120). | |
| * Installing fileset "CDE.CDE-HELP-RUN,r=B.11.11" (7 of 120). | |
| * Installing fileset "CDE.CDE-ICONS,r=B.11.11" (8 of 120). | |
| * Installing fileset "CDE.CDE-ITA-I-HELP,r=B.11.11" (9 of 120). | |
| * Installing fileset "CDE.CDE-JPN-E-HELP,r=B.11.11" (10 of 120). | |
| * Installing fileset "CDE.CDE-JPN-S-HELP,r=B.11.11" (11 of 120). | |
| * Installing fileset "CDE.CDE-KOR-E-HELP,r=B.11.11" (12 of 120). | |
| * Installing fileset "CDE.CDE-LANGS,r=B.11.11" (13 of 120). | |
| * Installing fileset "CDE.CDE-SCH-H-HELP,r=B.11.11" (14 of 120). | |
| * Installing fileset "CDE.CDE-SPA-I-HELP,r=B.11.11" (15 of 120). | |
| * Installing fileset "CDE.CDE-SWE-I-HELP,r=B.11.11" (16 of 120). | |
| * Installing fileset "CDE.CDE-TCH-B-HELP,r=B.11.11" (17 of 120). | |
| * Installing fileset "CDE.CDE-TCH-E-HELP,r=B.11.11" (18 of 120). | |
| * Installing fileset "ATOK.ATOK-RUN,r=A.03.00" (19 of 120). | |
| * Installing fileset "Asian-Core.IM-JPN-E-MAN,r=A.03.00" (20 of | |
| 120). | |
| * Installing fileset "Asian-Core.IM-JPN-MAN,r=A.03.00" (21 of | |
| 120). | |
| * Installing fileset "Asian-Core.IM-JPN-S-MAN,r=A.03.00" (22 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-INC,r=A.03.00" (23 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-JPN-RUN,r=A.03.00" (24 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-KOR-RUN,r=A.03.00" (25 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-RUN,r=A.03.00" (26 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-SCH-RUN,r=A.03.00" (27 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-SHLIBS,r=A.03.00" (28 of | |
| 120). | |
| * Installing fileset "Asian-X11.IMX11-TCH-RUN,r=A.03.00" (29 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-JPN-AUX,r=A.03.00" (30 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-JPN-MIN,r=A.03.00" (31 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-KOR-AUX,r=A.03.00" (32 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-KOR-BOLD,r=A.03.00" (33 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-KOR-MIN,r=A.03.00" (34 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-SCH-RUN,r=A.03.00" (35 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-TCH-B-AUX,r=A.03.00" (36 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-TCH-B-MIN,r=A.03.00" (37 of | |
| 120). | |
| * Installing fileset "Asian-X11.XPFT-TCH-C-AUX,r=A.03.00" (38 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-TCH-C-AUX,r=A.03.00" (39 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-TCH-C-MIN,r=A.03.00" (40 of | |
| 120). | |
| * Installing fileset "Asian-X11.XPFT-TCH-E-AUX,r=A.03.00" (41 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-TCH-E-AUX,r=A.03.00" (42 of | |
| 120). | |
| * Installing fileset "Asian-X11.XFNT-TCH-E-MIN,r=A.03.00" (43 of | |
| 120). | |
| * Installing fileset "Asian-X11.XJIM-RUN,r=A.03.00" (44 of 120). | |
| * Installing fileset "Asian-X11.XP-JPN-RUN,r=A.03.00" (45 of | |
| 120). | |
| * Installing fileset "Asian-X11FONTSRV.TT-JPN-RUN,r=A.03.00" (46 | |
| of 120). | |
| * Installing fileset "AudioSubsystem.AUD-ENG-A-MAN,r=B.11.11" | |
| (47 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-FRE-I-MSG,r=B.11.11" | |
| (48 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-GER-I-MSG,r=B.11.11" | |
| (49 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-ITA-I-MSG,r=B.11.11" | |
| (50 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-JPN-E-MAN,r=B.11.11" | |
| (51 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-JPN-E-MSG,r=B.11.11" | |
| (52 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-JPN-S-MAN,r=B.11.11" | |
| (53 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-JPN-S-MSG,r=B.11.11" | |
| (54 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-KOR-E-MSG,r=B.11.11" | |
| (55 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-SCH-H-MSG,r=B.11.11" | |
| (56 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-SPA-I-MSG,r=B.11.11" | |
| (57 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-SWE-I-MSG,r=B.11.11" | |
| (58 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-TCH-B-MSG,r=B.11.11" | |
| (59 of 120). | |
| * Installing fileset "AudioSubsystem.AUD-TCH-E-MSG,r=B.11.11" | |
| (60 of 120). | |
| * Installing fileset "AudioSubsystem.AUDIO-RUN,r=B.11.11" (61 of | |
| 120). | |
| * Installing fileset "AudioSubsystem.AUDIO-SHLIBS,r=B.11.11" (62 | |
| of 120). | |
| * Installing fileset "AudioSubsystem.AUDIO-SRV,r=B.11.11" (63 of | |
| 120). | |
| * Installing fileset "LdapUxClient.LDAP-C-SDK,r=B.04.00.02" (64 | |
| of 120). | |
| * Installing fileset "LdapUxClient.ADMIN-RUN,r=B.04.00.02" (65 | |
| of 120). | |
| * Installing fileset "LdapUxClient.CORE-RUN,r=B.04.00.02" (66 of | |
| 120). | |
| * Installing fileset "LdapUxClient.LDUX-ENG-A-MAN,r=B.04.00.02" | |
| (67 of 120). | |
| * Installing fileset "LdapUxClient.NATIVELDAP-RUN,r=B.04.00.02" | |
| (68 of 120). | |
| * Installing fileset "LdapUxClient.PAM-AUTHZ-RUN,r=B.04.00.02" | |
| (69 of 120). | |
| * Installing fileset "Contrib-Tools.CONTRIB,r=B.11.11.16.09" (70 | |
| of 120). | |
| * Installing fileset "Contrib-Tools.PDCINFO,r=B.11.11.16.09" (71 | |
| of 120). | |
| * Installing fileset "Contrib-Tools.PIMTOOL,r=B.11.11.16.09" (72 | |
| of 120). | |
| * Installing fileset "DigitalVideo.DVIDEO-SHLIBS,r=B.11.11" (73 | |
| of 120). | |
| * Installing fileset "DigitalVideo.DVIDEO-SRV,r=B.11.11" (74 of | |
| 120). | |
| * Installing fileset "EGBridge.EGB-RUN,r=A.03.00" (75 of 120). | |
| * Installing fileset "EMS-KRMonitor.KRMON-RUN,r=A.11.11.05" (76 | |
| of 120). | |
| * Installing fileset "EMS-KRMonitor.KRMON-DRV-CMN,r=A.11.11.05" | |
| (77 of 120). | |
| * Installing fileset "EMS-KRMonitor.KRMON-DRV-DRV,r=A.11.11.05" | |
| (78 of 120). | |
| * Installing fileset "EMS-KRMonitor.KRMON-MAN,r=A.11.11.05" (79 | |
| of 120). | |
| * Installing fileset "Jdk14.JDK14-PNV2,r=1.4.2.09.02" (80 of | |
| 120). | |
| * Installing fileset "Jdk14.JDK14-PWV2,r=1.4.2.09.02" (81 of | |
| 120). | |
| * Installing fileset "Jre14.JRE14-PNV2,r=1.4.2.09.02" (82 of | |
| 120). | |
| * Installing fileset "Jre14.JRE14-PNV2-H,r=1.4.2.09.02" (83 of | |
| 120). | |
| * Installing fileset "Jre14.JRE14-PWV2,r=1.4.2.09.02" (84 of | |
| 120). | |
| * Installing fileset "Jre14.JRE14-PWV2-H,r=1.4.2.09.02" (85 of | |
| 120). | |
| * Installing fileset "NisLdapServer.YPLDAP-SERVER,r=B.04.00.02" | |
| (86 of 120). | |
| You will need to update this file with appropriate | |
| configuration data. | |
| You will need to update this file with appropriate | |
| configuration data. | |
| You will need to update this file with appropriate | |
| configuration data. | |
| You will need to update this file with appropriate | |
| configuration data. | |
| * Installing fileset | |
| "Sup-Tool-Mgr.RELEASE-NOTES,r=B.11.11.16.09" (87 of 120). | |
| * Installing fileset "Sup-Tool-Mgr.STM-CATALOGS,r=B.11.11.16.09" | |
| (88 of 120). | |
| * Installing fileset "Sup-Tool-Mgr.STM-MAN,r=B.11.11.16.09" (89 | |
| of 120). | |
| * Installing fileset "Sup-Tool-Mgr.STM-SHLIBS,r=B.11.11.16.09" | |
| (90 of 120). | |
| * Installing fileset "Sup-Tool-Mgr.STM-UI-RUN,r=B.11.11.16.09" | |
| (91 of 120). | |
| * Installing fileset "Sup-Tool-Mgr.STM-UUT-RUN,r=B.11.11.16.09" | |
| (92 of 120). | |
| * Installing fileset "TechPrintServ.TPS-C-HELP,r=B.11.11.0412" | |
| (93 of 120). | |
| * Installing fileset "TechPrintServ.TPS-C-SERV,r=B.11.11.0412" | |
| (94 of 120). | |
| * Installing fileset "TechPrintServ.TPS-FONTS,r=B.11.11.0412" | |
| (95 of 120). | |
| * Installing fileset | |
| "TechPrintServ.TPS-FRE-I-HELP,r=B.11.11.0412" (96 of 120). | |
| * Installing fileset | |
| "TechPrintServ.TPS-FRE-I-SERV,r=B.11.11.0412" (97 of 120). | |
| * Installing fileset | |
| "TechPrintServ.TPS-GER-I-HELP,r=B.11.11.0412" (98 of 120). | |
| * Installing fileset | |
| "TechPrintServ.TPS-GER-I-SERV,r=B.11.11.0412" (99 of 120). | |
| * Installing fileset | |
| "TechPrintServ.TPS-JPN-E-HELP,r=B.11.11.0412" (100 of 120). | |
| * Installing fileset | |
| "TechPrintServ.TPS-JPN-S-HELP,r=B.11.11.0412" (101 of 120). | |
| * Installing fileset "TechPrintServ.TPS-MAN,r=B.11.11.0412" (102 | |
| of 120). | |
| * Installing fileset "TechPrintServ.TPS-MIN,r=B.11.11.0412" (103 | |
| of 120). | |
| * Installing fileset "TechPrintServ.TPS-RELNOTES,r=B.11.11.0412" | |
| (104 of 120). | |
| * Installing fileset "TechPrintServ.TPS-SERV,r=B.11.11.0412" | |
| (105 of 120). | |
| * Installing fileset "TechPrintServ.TPS-SHLIBS,r=B.11.11.0412" | |
| (106 of 120). | |
| * Installing fileset "VJE.VJE-RUN,r=A.03.00" (107 of 120). | |
| * Installing fileset "VUEtoCDE.V2C-ENG-A-MSG,r=B.11.11" (108 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-FRE-I-MSG,r=B.11.11" (109 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-GER-I-MSG,r=B.11.11" (110 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-ITA-I-MSG,r=B.11.11" (111 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-JPN-E-MSG,r=B.11.11" (112 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-JPN-S-MSG,r=B.11.11" (113 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-KOR-E-MSG,r=B.11.11" (114 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-RUN,r=B.11.11" (115 of 120). | |
| * Installing fileset "VUEtoCDE.V2C-SCH-H-MSG,r=B.11.11" (116 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-SPA-I-MSG,r=B.11.11" (117 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-SWE-I-MSG,r=B.11.11" (118 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-TCH-B-MSG,r=B.11.11" (119 of | |
| 120). | |
| * Installing fileset "VUEtoCDE.V2C-TCH-E-MSG,r=B.11.11" (120 of | |
| 120). | |
| * Summary of Execution Phase: | |
| * 4 of 124 filesets were Skipped. | |
| * 120 of 124 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/03/19 06:54:10 EST END install AGENT SESSION (pid=6109) | |
| (jobid=loopback-0002) | |
| * Software installation of this source (B7994 11i Mission Critical OE: | |
| CD2) is complete. | |
| ======================================================================= | |
| USER INTERACTION REQUIRED: | |
| To complete the installation you must now insert the | |
| "B7994 11i Mission Critical OE: CD3" CD. | |
| Once this is done, press the <Return> key to continue: | |
| * Starting swinstall of the source (B7994 11i Mission Critical OE: CD3). | |
| * Running command: "/usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM | |
| -f/tmp/ign_configure/software_file -x os_release=B.11.11 -x | |
| os_name=HP-UX:32 " | |
| ======= 11/03/19 07:16:06 EST BEGIN install AGENT SESSION (pid=7642) | |
| (jobid=loopback-0003) | |
| * Agent session started for user "root@localhost". (pid=7642) | |
| NOTE: The software item "Base-VXVM" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software "VRTSvxvm,r=3.5m,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| PHCO_27209.UX-CORE,fa=HP-UX_B.11.11_32/64 | |
| PHCO_27101.KERN-RUN,fa=HP-UX_B.11.11_32/64 | |
| PHCO_27101.UX-CORE,fa=HP-UX_B.11.11_32/64 | |
| PHKL_27096.CORE2-KRN,fa=HP-UX_B.11.11_32 | |
| NOTE: The software item "ISEEPlatform" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "ISEE-Chorus,r=A.5.1.395.021,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: OS-Core.CORE-SHLIBS,r>=B.11.00 | |
| X11.X11R6-SHLIBS,r>=B.11.00 | |
| * The software | |
| "ISEE-SysInfo,r=A.01.00.22,a=HP-UX_B.11.00_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: OS-Core.CORE-SHLIBS,r>=B.11.00 | |
| X11.X11R6-SHLIBS,r>=B.11.00 | |
| * The software | |
| "Isee_EmsListener,r=A.11.09.05,a=HP-UX_B.11.11_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: | |
| Sup-Tool-Mgr.STM-SHLIBS,r>=B.11.11.05.00 | |
| OS-Core.CORE-SHLIBS,r>=B.11.00 X11.X11R6-SHLIBS,r>=B.11.00 | |
| * The software | |
| "Availability,r=0.00.00979,a=HP-UX_B.11.00_32/64,v=HP" was | |
| successfully marked, but it depends on the following software | |
| items which could not be found in the source. However, these | |
| items may already be in the target. This will be checked | |
| during the Analysis Phase: OS-Core.CORE-SHLIBS,r>=B.11.00 | |
| X11.X11R6-SHLIBS,r>=B.11.00 | |
| NOTE: The software item "SysMgmtWeb" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "SysMgmtHomepage.SMH-UILIB-COM,r=A.2.2.0.4,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: openssl.OPENSSL-LIB | |
| * The software | |
| "SysMgmtHomepage.SMH-RUN,r=A.2.2.0.4,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: openssl.OPENSSL-LIB | |
| * The software | |
| "SysMgmtHomepage.SMH-DOC,r=A.2.2.0.4,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: openssl.OPENSSL-LIB | |
| * The software | |
| "SysMgmtHomepage.SMH-DOC-COM,r=A.2.2.0.4,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: openssl.OPENSSL-LIB | |
| * The software | |
| "SysMgmtHomepage.SMH-UILIB,r=A.2.2.0.4,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: openssl.OPENSSL-LIB | |
| WARNING: The software specified contains a fileset that changes the | |
| kernel. Either the attribute dynamic_module, used for dynamic | |
| changes, is specified, or the is_kernel attribute, used for | |
| static changes, is set to true. | |
| * Beginning Analysis Phase. | |
| * Source: localhost:/tmp/ign_configure/SD_CDROM | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for product information. | |
| NOTE: The filesystems in the filesystem table will not be checked | |
| against those currently mounted because the | |
| "mount_all_filesystems" option is set to "false". | |
| * Reading source for file information. | |
| * Executing preDSA command. | |
| NOTE: The used disk space on filesystem "/" is estimated to increase | |
| by 38352 Kbytes. | |
| This will leave 125496 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/opt" is estimated to | |
| increase by 704568 Kbytes. | |
| This will leave 1356640 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/usr" is estimated to | |
| increase by 39048 Kbytes. | |
| This will leave 1127840 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/var" is estimated to | |
| increase by 6288 Kbytes. | |
| This will leave 1411096 Kbytes of available user disk space | |
| after the installation. | |
| * Summary of Analysis Phase: | |
| * 66 of 66 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Install Execution Phase. | |
| * Filesets: 66 | |
| * Files: 23046 | |
| * Kbytes: 678288 | |
| * Installing bundle "B9788AA,r=1.3.1.16.00" . | |
| * Installing bundle "B9789AA,r=1.3.1.16.00" . | |
| * Installing bundle "Base-VXVM,r=B.03.50.5" . | |
| * Installing bundle "ISEEPlatform,r=A.03.95.021" . | |
| * Installing bundle "SysMgmtWeb,r=A.2.2.0.4" . | |
| * Installing bundle "T1455AA,r=1.3.1.16.00" . | |
| * Installing bundle "T1458AA,r=1.4.2.09.02" . | |
| * Installing bundle "hpuxwsApache,r=A.2.0.54.01" . | |
| * Installing bundle "hpuxwsWebmin,r=A.1.070.04" . | |
| * Installing bundle "hpuxwsXml,r=A.2.00" . | |
| * Installing bundle "perl,r=D.5.8.3.B" . | |
| * Installing fileset "VRTSvxvm.VXVM-RUN,r=3.5m" (1 of 66). | |
| NOTE: Port 4145 has been allocated for Volume Replicator use | |
| * Installing fileset "VRTSvxvm.VXVM-KRN,r=3.5m" (2 of 66). | |
| NOTE: The VxVM drivers have been added to the /stand/system | |
| file. You must build the kernel and reboot. You need to build | |
| the kernel and reboot only if the installation process does not | |
| automatically do it for you. | |
| Use " /usr/sbin/mk_kernel -s /stand/system " | |
| to build the new kernel | |
| * Installing fileset "VRTSvxvm.VXMS,r=3.5m" (3 of 66). | |
| * Installing fileset "VRTSvxvm.VXVM-ENG-A-MAN,r=3.5m" (4 of 66). | |
| * Installing fileset "VRTSvxvm.VXVM-HELP,r=3.5m" (5 of 66). | |
| * Installing fileset "ISEE-Java.JAVA-RUN,r=A.01.31.12" (6 of | |
| 66). | |
| * Installing fileset "ISEE.CORE,r=A.03.95.021" (7 of 66). | |
| * Installing fileset "ISEE-Chorus.MADHPSERVICES,r=A.5.1.395.021" | |
| (8 of 66). | |
| * Installing fileset "Availability.CODE,r=0.00.00979" (9 of 66). | |
| * Installing fileset "Cpumap.CODE,r=A.00.02.006" (10 of 66). | |
| * Installing fileset "ISEE-SysInfo.SYSINFOBIN,r=A.01.00.22" (11 | |
| of 66). | |
| * Installing fileset | |
| "Isee_EmsListener.ISEE-EMSLSTNR,r=A.11.09.05" (12 of 66). | |
| * Installing fileset | |
| "Isee_EmsListener.ISEE-EMSCONF,r=A.11.09.05" (13 of 66). | |
| * Installing fileset "Jdk13.JDK13-COM,r=1.3.1.16.00" (14 of 66). | |
| * Installing fileset "Jdk13.JDK13-DEMO,r=1.3.1.16.00" (15 of | |
| 66). | |
| * Installing fileset "Jdk13.JDK13-PA11,r=1.3.1.16.00" (16 of | |
| 66). | |
| * Installing fileset "Jdk13.JDK13-PA20,r=1.3.1.16.00" (17 of | |
| 66). | |
| * Installing fileset "Jpi13.JPI13-COM,r=1.3.1.16.00" (18 of 66). | |
| * Installing fileset "Jpi13.JPI13-COM-DOC,r=1.3.1.16.00" (19 of | |
| 66). | |
| * Installing fileset "Jpi13.JPI13-PA11,r=1.3.1.16.00" (20 of | |
| 66). | |
| * Installing fileset "Jpi14.JPI14-COM,r=1.4.2.09.02" (21 of 66). | |
| * Installing fileset "Jpi14.JPI14-COM-DOC,r=1.4.2.09.02" (22 of | |
| 66). | |
| * Installing fileset "Jpi14.JPI14-PA11,r=1.4.2.09.02" (23 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-COM,r=1.3.1.16.00" (24 of 66). | |
| * Installing fileset "Jre13.JRE13-COM-DOC,r=1.3.1.16.00" (25 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-PA11,r=1.3.1.16.00" (26 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-PA11-CL,r=1.3.1.16.00" (27 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-PA11-HS,r=1.3.1.16.00" (28 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-PA20,r=1.3.1.16.00" (29 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-PA20-CL,r=1.3.1.16.00" (30 of | |
| 66). | |
| * Installing fileset "Jre13.JRE13-PA20-HS,r=1.3.1.16.00" (31 of | |
| 66). | |
| * Installing fileset "MCPS-COMMON.BIN,r=A.01.01.01" (32 of 66). | |
| * Installing fileset "Perl5-32.PERL-MAN,r=D.5.8.3.B" (33 of 66). | |
| * Installing fileset "Perl5-32.PERL-RUN,r=D.5.8.3.B" (34 of 66). | |
| * Installing fileset "Perl5-64.PERL-MAN,r=D.5.8.3.B" (35 of 66). | |
| * Installing fileset "Perl5-64.PERL-RUN,r=D.5.8.3.B" (36 of 66). | |
| * Installing fileset "hpuxwsAPACHE.APACHE,r=A.2.0.54.01" (37 of | |
| 66). | |
| * Installing fileset "hpuxwsAPACHE.APACHE2,r=A.2.0.54.01" (38 of | |
| 66). | |
| * Installing fileset "hpuxwsAPACHE.WEBPROXY,r=A.2.0.54.01" (39 | |
| of 66). | |
| * Installing fileset "hpuxwsAPACHE.PHP,r=A.2.0.54.01" (40 of | |
| 66). | |
| * Installing fileset "hpuxwsAPACHE.PHP2,r=A.2.0.54.01" (41 of | |
| 66). | |
| * Installing fileset "hpuxwsAPACHE.MOD_PERL,r=A.2.0.54.01" (42 | |
| of 66). | |
| * Installing fileset "hpuxwsAPACHE.MOD_PERL2,r=A.2.0.54.01" (43 | |
| of 66). | |
| * Installing fileset "hpuxwsAPACHE.MOD_JK2,r=A.2.0.54.01" (44 of | |
| 66). | |
| * Installing fileset "hpuxwsAPACHE.MOD_JK,r=A.2.0.54.01" (45 of | |
| 66). | |
| * Installing fileset "hpuxwsAPACHE.AUTH_LDAP,r=A.2.0.54.01" (46 | |
| of 66). | |
| * Installing fileset "hpuxwsAPACHE.AUTH_LDAP2,r=A.2.0.54.01" (47 | |
| of 66). | |
| * Installing fileset "SysMgmtHomepage.SMH-DOC,r=A.2.2.0.4" (48 | |
| of 66). | |
| * Installing fileset "SysMgmtHomepage.SMH-DOC-COM,r=A.2.2.0.4" | |
| (49 of 66). | |
| * Installing fileset "SysMgmtHomepage.SMH-RUN,r=A.2.2.0.4" (50 | |
| of 66). | |
| * Installing fileset "SysMgmtHomepage.SMH-UILIB,r=A.2.2.0.4" (51 | |
| of 66). | |
| * Installing fileset "SysMgmtHomepage.SMH-UILIB-COM,r=A.2.2.0.4" | |
| (52 of 66). | |
| * Installing fileset "VRTSob.VEAS-FILESET,r=3.0.2.261a" (53 of | |
| 66). | |
| * Installing fileset "VRTSfspro.FSPRO-PRG,r=3.5-ga08" (54 of | |
| 66). | |
| * Installing fileset "VRTSobgui.VEA-FILESET,r=3.0.2.261a" (55 of | |
| 66). | |
| * Installing fileset "VRTSvlic.VLIC-RUN,r=3.00.007e" (56 of 66). | |
| * Installing fileset "VRTSvmdoc.VXVM-DOC,r=3.5m" (57 of 66). | |
| * Installing fileset "VRTSvmpro.VMPRO-PRG,r=3.5m" (58 of 66). | |
| * Installing fileset "hpuxwsWEBMIN.WEBMIN,r=A.1.070.04" (59 of | |
| 66). | |
| * Installing fileset "hpuxwsWEBMIN.HPDOCS,r=A.1.070.04" (60 of | |
| 66). | |
| * Installing fileset "hpuxwsXML.XMLTOOLS,r=A.2.00" (61 of 66). | |
| * Installing fileset "hpuxwsXML.BATIK,r=A.2.00" (62 of 66). | |
| * Installing fileset "hpuxwsXML.COCOON,r=A.2.00" (63 of 66). | |
| * Installing fileset "hpuxwsXML.FOP,r=A.2.00" (64 of 66). | |
| * Installing fileset "hpuxwsXML.XALANJ,r=A.2.00" (65 of 66). | |
| * Installing fileset "hpuxwsXML.XERCESJ,r=A.2.00" (66 of 66). | |
| * Summary of Execution Phase: | |
| * 66 of 66 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/03/19 08:27:16 EST END install AGENT SESSION (pid=7642) | |
| (jobid=loopback-0003) | |
| * Software installation of this source (B7994 11i Mission Critical OE: | |
| CD3) is complete. | |
| ======================================================================= | |
| USER INTERACTION REQUIRED: | |
| To complete the installation you must now insert the | |
| "B7994 11i Mission Critical OE: CD4" CD. | |
| Once this is done, press the <Return> key to continue: | |
| * Starting swinstall of the source (B7994 11i Mission Critical OE: CD4). | |
| * Running command: "/usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM | |
| -f/tmp/ign_configure/software_file -x os_release=B.11.11 -x | |
| os_name=HP-UX:32 " | |
| ======= 11/03/19 08:33:48 EST BEGIN install AGENT SESSION (pid=8664) | |
| (jobid=loopback-0004) | |
| * Agent session started for user "root@localhost". (pid=8664) | |
| NOTE: The software item "NParCmds" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "NPartition.NPAR-ENG-A-MAN,r=A.01.02,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: NParProvider.NPAR-RUN | |
| PHCO_31878.SYS-ADMIN | |
| * The software | |
| "NPartition.NPARCMDS-RUN,r=A.01.02,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: NParProvider.NPAR-RUN | |
| PHCO_31878.SYS-ADMIN | |
| NOTE: The software item "ParMgr" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "PartitionManager.PARMGR-RUN,r=B.11.11.02.00.05.03,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: SysMgmtHomepage.SMH-RUN | |
| NParProvider.NPAR-RUN,r>=B.01.00.% | |
| SystemAdmin.SAM,r>=B.11.11.% NParProvider.NPAR-RUN | |
| PHCO_31878.SYS-ADMIN | |
| ERROR: Could not apply the software selection "T2743AA" because it | |
| refers to a bundle or to a product, subproduct or fileset | |
| within a bundle but no compatible bundles meeting the | |
| specification were found. | |
| NOTE: The software item "vparprovider" is a bundle (or a product, | |
| subproduct or fileset contained within a bundle). This item | |
| was successfully marked, but difficulties were encountered | |
| while marking some items that it depends on. The messages | |
| below show which software items encountered difficulties and | |
| exactly what these difficulties were: | |
| * The software | |
| "VParProvider.VPAR-DOC,r=B.11.11.01.01,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| WBEMServices.WBEM-CORE,r>=A.02.00.% | |
| * The software | |
| "VParProvider.VPAR-RUN,r=B.11.11.01.01,a=HP-UX_B.11.11_32/64,v=HP" | |
| was successfully marked, but it depends on the following | |
| software items which could not be found in the source. | |
| However, these items may already be in the target. This will | |
| be checked during the Analysis Phase: | |
| WBEMServices.WBEM-CORE,r>=A.02.00.% | |
| * Beginning Analysis Phase. | |
| * Source: localhost:/tmp/ign_configure/SD_CDROM | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for product information. | |
| NOTE: The filesystems in the filesystem table will not be checked | |
| against those currently mounted because the | |
| "mount_all_filesystems" option is set to "false". | |
| * Reading source for file information. | |
| * Executing preDSA command. | |
| NOTE: The used disk space on filesystem "/" is estimated to increase | |
| by 32 Kbytes. | |
| This will leave 125720 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/opt" is estimated to | |
| increase by 389728 Kbytes. | |
| This will leave 958696 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/var" is estimated to | |
| increase by 1808 Kbytes. | |
| This will leave 1413848 Kbytes of available user disk space | |
| after the installation. | |
| NOTE: The used disk space on filesystem "/usr" is estimated to | |
| increase by 1056 Kbytes. | |
| This will leave 1127152 Kbytes of available user disk space | |
| after the installation. | |
| * Summary of Analysis Phase: | |
| * 39 of 39 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Install Execution Phase. | |
| * Filesets: 39 | |
| * Files: 5223 | |
| * Kbytes: 363904 | |
| * Installing bundle "Java15JDK,r=1.5.0.01.01" . | |
| * Installing bundle "Java15JDKadd,r=1.5.0.01.01" . | |
| * Installing bundle "Java15JRE,r=1.5.0.01.01" . | |
| * Installing bundle "Java15JREadd,r=1.5.0.01.01" . | |
| * Installing bundle "NParCmds,r=A.01.02" . | |
| * Installing bundle "ParMgr,r=B.11.11.02.00.05.03" . | |
| * Installing bundle "T1456AA,r=1.4.2.09.02" . | |
| * Installing bundle "T1457AA,r=1.4.2.09.02" . | |
| * Installing bundle "T1471AA,r=A.04.00.002" . | |
| * Installing bundle "hpuxwsTomcat,r=A.5.5.9.01" . | |
| * Installing bundle "vparprovider,r=B.11.11.01.01" . | |
| * Installing fileset "Jdk14.JDK14-COM,r=1.4.2.09.02" (1 of 39). | |
| * Installing fileset "Jdk14.JDK14-DEMO,r=1.4.2.09.02" (2 of 39). | |
| * Installing fileset "Jdk14.JDK14-PA11,r=1.4.2.09.02" (3 of 39). | |
| * Installing fileset "Jdk14.JDK14-PA20,r=1.4.2.09.02" (4 of 39). | |
| * Installing fileset "Jdk14.JDK14-PA20W,r=1.4.2.09.02" (5 of | |
| 39). | |
| * Installing fileset "Jdk15.JDK15-COM,r=1.5.0.01.01" (6 of 39). | |
| * Installing fileset "Jdk15.JDK15-DEMO,r=1.5.0.01.01" (7 of 39). | |
| * Installing fileset "Jdk15.JDK15-PA20,r=1.5.0.01.01" (8 of 39). | |
| * Installing fileset "Jdk15.JDK15-PA20W,r=1.5.0.01.01" (9 of | |
| 39). | |
| * Installing fileset "Jdk15.JDK15-PNV2,r=1.5.0.01.01" (10 of | |
| 39). | |
| * Installing fileset "Jdk15.JDK15-PWV2,r=1.5.0.01.01" (11 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-COM,r=1.4.2.09.02" (12 of 39). | |
| * Installing fileset "Jre14.JRE14-COM-DOC,r=1.4.2.09.02" (13 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-PA11,r=1.4.2.09.02" (14 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-PA11-HS,r=1.4.2.09.02" (15 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-PA20,r=1.4.2.09.02" (16 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-PA20-HS,r=1.4.2.09.02" (17 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-PA20W,r=1.4.2.09.02" (18 of | |
| 39). | |
| * Installing fileset "Jre14.JRE14-PA20W-HS,r=1.4.2.09.02" (19 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-COM,r=1.5.0.01.01" (20 of 39). | |
| * Installing fileset "Jre15.JRE15-COM-DOC,r=1.5.0.01.01" (21 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PA20,r=1.5.0.01.01" (22 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PA20-HS,r=1.5.0.01.01" (23 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PA20W,r=1.5.0.01.01" (24 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PA20W-HS,r=1.5.0.01.01" (25 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PNV2,r=1.5.0.01.01" (26 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PNV2-H,r=1.5.0.01.01" (27 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PWV2,r=1.5.0.01.01" (28 of | |
| 39). | |
| * Installing fileset "Jre15.JRE15-PWV2-H,r=1.5.0.01.01" (29 of | |
| 39). | |
| * Installing fileset "NPartition.NPAR-ENG-A-MAN,r=A.01.02" (30 | |
| of 39). | |
| * Installing fileset "NPartition.NPARCMDS-RUN,r=A.01.02" (31 of | |
| 39). | |
| * Installing fileset | |
| "PartitionManager.PARMGR,r=B.11.11.02.00.05.03" (32 of 39). | |
| * Installing fileset | |
| "PartitionManager.PARMGR-HELP,r=B.11.11.02.00.05.03" (33 of | |
| 39). | |
| * Installing fileset | |
| "PartitionManager.PARMGR-MAN,r=B.11.11.02.00.05.03" (34 of | |
| 39). | |
| * Installing fileset | |
| "PartitionManager.PARMGR-RUN,r=B.11.11.02.00.05.03" (35 of | |
| 39). | |
| * Installing fileset "Secure_Shell.SECURE_SHELL,r=A.04.00.002" | |
| (36 of 39). | |
| * Installing fileset "VParProvider.VPAR-DOC,r=B.11.11.01.01" (37 | |
| of 39). | |
| * Installing fileset "VParProvider.VPAR-RUN,r=B.11.11.01.01" (38 | |
| of 39). | |
| * Installing fileset "hpuxwsTOMCAT.TOMCAT,r=A.5.5.9.01" (39 of | |
| 39). | |
| * Summary of Execution Phase: | |
| * 39 of 39 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/03/19 09:09:02 EST END install AGENT SESSION (pid=8664) | |
| (jobid=loopback-0004) | |
| * Software installation of this source (B7994 11i Mission Critical OE: | |
| CD4) is complete. | |
| NOTE: tlinstall is searching filesystem - please be patient | |
| NOTE: Successfully completed | |
| * Loading_software: Complete | |
| * Build_Kernel: Begin | |
| * Tuned kernel for large swap space: "maxswapchunks 512". | |
| * Building a new kernel using the command: "/usr/sbin/mk_kernel -o | |
| /stand/vmunix". | |
| Generating module: krm... | |
| /usr/bin/mkdir -p /stand/build | |
| Compiling /stand/build/conf.c... | |
| Loading the kernel... | |
| (Warning) Optimizing ADDILs in the presence of the debug information. Debug information may be corrupted (1594) | |
| Generating kernel symbol table... | |
| * Build_Kernel: Complete | |
| * Boot_From_Client_Disk: Begin | |
| * Rebooting machine as expected. | |
| NOTE: Rebooting system. | |
| sync'ing disks (0 buffers to flush): | |
| 0 buffers not flushed | |
| 0 buffers still dirty | |
| Closing open logical volumes... | |
| Done | |
| SeaBIOS wants SYSTEM HALT. | |
| Connection closed by foreign host. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ telnet localhost 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux | |
| Boot | |
| : disc(8/0/0/0.0.0;0)/stand/vmunix | |
| 8818940 + 1040384 + 641920 start 0x14c268 | |
| Connection closed by foreign host. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ telnet localhost 54321 | |
| Trying 127.0.0.1... | |
| Connected to localhost. | |
| Escape character is '^]'. | |
| Firmware Version 6.1 | |
| Duplex Console IO Dependent Code (IODC) revision 1 | |
| Memory Test/Initialization Completed | |
| ------------------------------------------------------------------------------ | |
| (c) Copyright 2017-2018 Helge Deller <[email protected]> and SeaBIOS developers. | |
| ------------------------------------------------------------------------------ | |
| Processor Speed State Coprocessor State Cache Size | |
| --------- -------- --------------------- ----------------- ---------- | |
| 0 250 MHz Active Functional 0 KB | |
| Available memory: 512 MB | |
| Good memory required: 16 MB | |
| Primary boot path: FWSCSI.0.0 | |
| Alternate boot path: FWSCSI.2.0 | |
| Console path: SERIAL_1.9600.8.none | |
| Keyboard path: PS2 | |
| Available boot devices: | |
| 1. DVD/CD [lsi 00:00.0 2:0 Drive QEMU QEMU CD-ROM 2.5+] | |
| 2. lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| 3. lsi 00:00.0 1:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting from lsi 00:00.0 0:0 Drive QEMU QEMU HARDDISK 2.5+ | |
| Booting... | |
| Boot IO Dependent Code (IODC) revision 153 | |
| HARD Booted. | |
| ISL Revision A.00.43 Apr 12, 2000 | |
| ISL booting hpux | |
| Boot | |
| : disc(8/0/0/0.0.0;0)/stand/vmunix | |
| telnet> mode character | |
| 8818940 + 1040384 + 641920 start 0x14c268 | |
| WARNING: can't enable implementation specific instructions | |
| NOTICE: nfs3_link(): File system was registered at index 3. | |
| NOTICE: autofs_link(): File system was registered at index 6. | |
| NOTICE: cachefs_link(): File system was registered at index 7. | |
| System Console is on the Built-In Serial Interface | |
| Logical volume 64, 0x3 configured as ROOT | |
| Logical volume 64, 0x2 configured as SWAP | |
| Logical volume 64, 0x2 configured as DUMP | |
| Swap device table: (start & size given in 512-byte blocks) | |
| entry 0 - major is 64, minor is 0x2; start = 0, size = 2097152 | |
| Starting the STREAMS daemons-phase 1 | |
| Checking root file system. | |
| file system is clean - log replay is not required | |
| Root check done. | |
| Create STCP device files | |
| $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:05:38 PST 2000 $ | |
| Memory Information: | |
| physical page size = 4096 bytes, logical page size = 4096 bytes | |
| Physical: 524288 Kbytes, lockable: 396828 Kbytes, available: 457052 Kbytes | |
| Volume group "/dev/vg00" has been successfully changed. | |
| * Running the ioinit command ("/sbin/ioinit -c") | |
| * Creating device files via the insf command. | |
| insf: Installing special files for sdisk instance 0 address 8/0/0/0.0.0 | |
| insf: Installing special files for sdisk instance 1 address 8/0/0/0.1.0 | |
| insf: Installing special files for sdisk instance 2 address 8/0/0/0.2.0 | |
| insf: Installing special files for sctl instance 0 address 8/0/0/0.7.0 | |
| insf: Installing special files for btlan instance 0 address 8/0/1/0 | |
| insf: Installing special files for asio0 instance 0 address 8/0/63 | |
| insf: Installing special files for pseudo driver cn | |
| insf: Installing special files for pseudo driver devkrs | |
| insf: Installing special files for pseudo driver mm | |
| insf: Installing special files for pseudo driver ip | |
| insf: Installing special files for pseudo driver arp | |
| insf: Installing special files for pseudo driver rawip | |
| insf: Installing special files for pseudo driver tcp | |
| insf: Installing special files for pseudo driver udp | |
| insf: Installing special files for pseudo driver stcpmap | |
| insf: Installing special files for pseudo driver nuls | |
| insf: Installing special files for pseudo driver netqa | |
| insf: Installing special files for pseudo driver ptym | |
| insf: Installing special files for pseudo driver ptys | |
| insf: Installing special files for pseudo driver telm | |
| insf: Installing special files for pseudo driver tels | |
| insf: Installing special files for pseudo driver tlclts | |
| insf: Installing special files for pseudo driver tlcots | |
| insf: Installing special files for pseudo driver tlcotsod | |
| insf: Installing special files for pseudo driver dmem | |
| insf: Installing special files for pseudo driver dmp | |
| insf: Installing special files for pseudo driver vols | |
| insf: Installing special files for pseudo driver iomem | |
| insf: Installing special files for pseudo driver dev_config | |
| insf: Installing special files for pseudo driver strlog | |
| insf: Installing special files for pseudo driver sad | |
| insf: Installing special files for pseudo driver echo | |
| insf: Installing special files for pseudo driver dlpi | |
| insf: Installing special files for pseudo driver ptm | |
| insf: Installing special files for pseudo driver pts | |
| insf: Installing special files for pseudo driver diag1 | |
| insf: Installing special files for pseudo driver klog | |
| insf: Installing special files for pseudo driver sy | |
| insf: Installing special files for pseudo driver kepd | |
| insf: Installing special files for pseudo driver diag2 | |
| insf: Installing special files for pseudo driver root | |
| * Restoring autoboot to OFF. | |
| * Boot_From_Client_Disk: Complete | |
| * Run_SD_Configure_Scripts: Begin | |
| * Running swconfig command ("/usr/sbin/swconfig -f | |
| /tmp/ign_configure/software_file") for source (B7994 11i Mission | |
| Critical OE: CD1). | |
| ======= 11/05/19 22:44:01 EST BEGIN configure AGENT SESSION (pid=85) | |
| (jobid=loopback-0005) | |
| * Agent session started for user "root@localhost". (pid=85) | |
| * Beginning Analysis Phase. | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for file information. | |
| * Summary of Analysis Phase: | |
| * 723 of 723 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Configure Execution Phase. | |
| * Filesets: 723 | |
| NOTE: New paths were added to /etc/MANPATH | |
| NOTE: File /etc/rc.config.d/hparray not found. | |
| It has been created. | |
| NOTE: HPARRAY_START_STOP has been set to 1 in /etc/rc.config.d/hparray | |
| to allow the HPAutoRAID product to automatically restart | |
| following a system reboot. | |
| NOTE: Starting the disk array monitor daemons. | |
| NOTE: Check the file /etc/hpC2400/HPARRAY.INFO | |
| to determine if any arrays were found. | |
| NOTE: Starting the disk array monitor daemons. | |
| NOTE: Check the file /etc/hparray/HPARAMGR.INFO | |
| to determine if any arrays were found. | |
| NOTE: To start UPS Monitor, /etc/inittab must be edited to remove | |
| comment character (#) from ups command line. | |
| Prior to this, ensure the ups configuration filename parameter | |
| is correct for the system (default is /etc/ups_conf). Edit line | |
| if necessary. | |
| Also, ensure that /dev/tty's specified in the ups configuration | |
| file are actually connected to UPS RS-232 ports, and that no | |
| getty's are being spawned from /etc/inittab for these tty's. | |
| Edit inittab to remove or comment-out such getty's. | |
| To activate UPS Monitor, kill running ups_mond process. Run | |
| "init q" to cause inittab changes to have effect. | |
| NOTE: NFS_CLIENT in /etc/rc.config.d/nfsconf is now set to 1. | |
| NOTE: NFS_SERVER in /etc/rc.config.d/nfsconf is now set to 1. | |
| NOTE: Installing special files for pseudo driver telm. | |
| NOTE: Installing special files for pseudo driver tels. | |
| NOTE: Remove LANCONFIG_ARG from //etc/rc.config.d/netconf | |
| No change required | |
| NOTE: Installing special files for pseudo driver ptm. | |
| NOTE: Installing special files for pseudo driver pts. | |
| NOTE: The sendmail server now requires a sendmail.cw file which must | |
| contain a list of local host names. A sample | |
| /etc/mail/sendmail.cw is being installed that contains | |
| extensive comments on the format. You MUST edit this file | |
| before sendmail can be run as a server. | |
| NOTE: The defaults file "/var/adm/sw/defaults" | |
| is being edited to comment out any lines that | |
| explicitly specify an rpc_binding_info value. | |
| NOTE: A new version of "/var/sam/ts/pam_dir.reg" | |
| has been placed on the system. | |
| NOTE: A new version of "/var/sam/ts/pam_mod.reg" | |
| has been placed on the system. | |
| NOTE: A new version of "/etc/sam/reg_da.db" | |
| has been placed on the system. | |
| NOTE: A new version of "/etc/sam/reg_files.db" | |
| has been placed on the system. | |
| NOTE: A new version of "/etc/sam/reg_tm.db" | |
| has been placed on the system. | |
| NOTE: The file /var/adm/inetd.sec does not exist and is being | |
| created | |
| Nov 5 23:16:07 prngd[2656]: prngd 0.9.26 (12 Jul 2002) started up for user root | |
| Nov 5 23:16:07 prngd[2656]: have 6 out of 60 filedescriptors open | |
| ERROR: Unable to create self-signed host certificate. | |
| See the file /tmp/hostcert.out for details | |
| NOTE: Cannot find the fully-qualified domain name(FQDN) for this | |
| system, SSL certificates for WBEMServices are created with | |
| the short hostname. | |
| Correct this either by editing the /etc/hosts file or by | |
| making the appropriate DNS registration. If not corrected, | |
| the created certificates may not be acceptable to the | |
| WBEMService clients that expect a FQDN in the common name | |
| field of the SSL certificate. | |
| NOTE: Starting cimserver in order to load mof files | |
| NOTE: CIM Repository is being built - please be patient | |
| NOTE: A copy of the previous inittab has been saved in: | |
| /var/opt/wbem/inittab.old. | |
| NOTE: /etc/PATH already contains the "/opt/hparray/bin" path for | |
| the HPAutoRAID product. | |
| NOTE: Starting the disk array monitor daemons. | |
| NOTE: Check the file /etc/hpC2400/HPARRAY.INFO | |
| to determine if any arrays were found. | |
| NOTE: /etc/PATH already contains the "/opt/hparray/bin" path for | |
| the HP Fibre Array/60 product. | |
| NOTE: Starting the disk array monitor daemons. | |
| NOTE: Check the file /etc/hparray/HPARAMGR.INFO | |
| to determine if any arrays were found. | |
| NOTE: A new version of "/etc/sam/reg_da.db" | |
| has been placed on the system. | |
| NOTE: A new version of "/etc/sam/reg_files.db" | |
| has been placed on the system. | |
| NOTE: A new version of "/etc/sam/reg_tm.db" | |
| has been placed on the system. | |
| NOTE: A new version of /etc/X11/XHPKeymaps | |
| has been placed on the system. | |
| The new version may be essential to the functioning of your system. | |
| The old version is in /etc/X11/XHPKeymaps.old. | |
| It appears to have been edited. You may want to | |
| merge your changes into the new version. | |
| NOTE, Some mandatory conversion was done to | |
| /etc/X11/XF86Config. The original was save in | |
| /etc/X11/XF86Config.prev | |
| NOTE: Checking if cimserver is running | |
| NOTE: Checking iCOD WBEM provider registration using cimprovider. | |
| NOTE: Removing old symbolic link | |
| /opt/wbem/providers/lib/libiCODProviderModule.sl | |
| NOTE: Creating symbolic link to | |
| /opt/icod/lib/libiCODProviderModule.1 | |
| NOTE: Listing namespaces in which to register iCOD WBEM provider | |
| class definitions. | |
| NOTE: Removing HP_iCODComplex WBEM class from namespace | |
| root/cimv2/npar. | |
| NOTE: Updating iCOD WBEM provider class definitions in namespace | |
| root/cimv2/npar using cimmof. | |
| NOTE: Registering iCOD WBEM provider module using cimmof. | |
| NOTE: Checking for partitionable system. | |
| NOTE: System is not an iCOD supported system; done. | |
| * Running config clean command /usr/lbin/sw/config_clean. | |
| * Summary of Execution Phase: | |
| * 723 of 723 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/06/19 02:01:58 EST END configure AGENT SESSION (pid=85) | |
| (jobid=loopback-0005) | |
| * Running swconfig command ("/usr/sbin/swconfig -f | |
| /tmp/ign_configure/software_file") for source (B7994 11i Mission | |
| Critical OE: CD2). | |
| ======= 11/06/19 02:02:19 EST BEGIN configure AGENT SESSION | |
| (pid=3921) (jobid=loopback-0006) | |
| * Agent session started for user "root@localhost". (pid=3921) | |
| * Beginning Analysis Phase. | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for file information. | |
| NOTE: The fileset "OS-Core.C-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN2-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.SYS-ADMIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMDS-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMDS-AUX,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-KRN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "NFS.NFS-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NETTL-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NETTL-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NMS-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NMS2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-RUN-64,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STRTIO2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STRTIO-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STRTIO-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "InternetSrvcs.INETSVCS-INETD,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Upgrade.UPG-TLINK,l=/opt/upgrade,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OVSNMPAgent.MASTER,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OVSNMPAgent.SUBAGT-HPUNIX,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OVSNMPAgent.SUBAGT-MIB2,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.OBAM-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.SAM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "TextFormatters.TEXT-FMT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TT,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "CDE.CDE-MIN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "CDE.CDE-JPN-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-JPN-S-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-KOR-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SCH-H-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TCH-B-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TCH-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "ImagingSubsystem.IMAGE-SHLIBS,l=/opt/image,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "X11.X11R6-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11R5-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.MKFONTDIR,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-FONTSRV,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.MOTIF-SHLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "EMS-Core.EMS-CORE,l=/,r=A.04.20" is already | |
| configured. | |
| NOTE: The fileset "EMS-Core.EMS-MX,l=/,r=A.04.20" is already | |
| configured. | |
| NOTE: The fileset "EMS-Config.EMS-GUI,l=/,r=A.04.20" is already | |
| configured. | |
| NOTE: The fileset "International.CHINESES,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.CHINESET,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.FRENCH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.GERMAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.ITALIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.JAPANESE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.KOREAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.SPANISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.SWEDISH,l=/,r=B.11.11" is already | |
| configured. | |
| * Summary of Analysis Phase: | |
| * 64 of 184 filesets will be Skipped. | |
| * 120 of 184 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Configure Execution Phase. | |
| * Filesets: 120 | |
| NOTE: This system is NOT configured for audio; therefore, the audio | |
| server (Aserver) will NOT be started during system startup | |
| NOTE: See /tmp/V2C-RUN_config.log for dtappintegrate results | |
| * Running config clean command /usr/lbin/sw/config_clean. | |
| * Summary of Execution Phase: | |
| * 64 of 184 filesets were Skipped. | |
| * 120 of 184 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/06/19 02:12:54 EST END configure AGENT SESSION (pid=3921) | |
| (jobid=loopback-0006) | |
| * Running swconfig command ("/usr/sbin/swconfig -f | |
| /tmp/ign_configure/software_file") for source (B7994 11i Mission | |
| Critical OE: CD3). | |
| ======= 11/06/19 02:13:16 EST BEGIN configure AGENT SESSION | |
| (pid=5250) (jobid=loopback-0007) | |
| * Agent session started for user "root@localhost". (pid=5250) | |
| * Beginning Analysis Phase. | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for file information. | |
| NOTE: The fileset "OS-Core.C-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN2-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-KRN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "NFS.NFS-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "PHKL_27096.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27101.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27101.KERN-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_28169.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset | |
| "ImagingSubsystem.IMAGE-SHLIBS,l=/opt/image,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "X11.X11R6-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11R5-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.STM-SHLIBS,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-SRC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-RUN,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-PVT,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-PRNG,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-MIS,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-MAN,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-LIB,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-INC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-DOC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-CONF,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-CER,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| * Summary of Analysis Phase: | |
| * 28 of 94 filesets will be Skipped. | |
| * 66 of 94 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Configure Execution Phase. | |
| * Filesets: 66 | |
| NOTE: HPUX version is B.11.11 | |
| ** WARNING **: SeaBIOS: Unimplemented PDC proc PDC_SYSTEM_INFO(143) option 0 result=8b4640 ARG3=0 ARG4=0 ARG5=0 ARG6=0 ARG7=0 | |
| ** WARNING **: SeaBIOS: Unimplemented PDC proc UNKNOWN!(134) option 1 result=8b4640 ARG3=0 ARG4=0 ARG5=0 ARG6=0 ARG7=0 | |
| NOTE: SysInfo setSysInfoCronEntry.sh. | |
| ISEE preinstall configuration script was not run prior to | |
| the ISEE installation. | |
| To setup SysInfoRunMap.sh to run from cron, execute the | |
| following: | |
| /opt/hpservices/contrib/SysInfo/bin/setSysInfoCronEntry.sh -i | |
| NOTE: Installing rst_dm_TL_adapter.clcfg version for HP-UX 11.11 and later | |
| NOTE: Adding VRTSfspro to VEA Registry ... done | |
| NOTE: To use the VRTSfspro you must restart the VEA server. | |
| Refer to the man page for vxsvc(1M). | |
| NOTE: VRTSfspro configuration installation complete. | |
| * Running config clean command /usr/lbin/sw/config_clean. | |
| * Summary of Execution Phase: | |
| * 28 of 94 filesets were Skipped. | |
| * 66 of 94 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/06/19 02:49:37 EST END configure AGENT SESSION (pid=5250) | |
| (jobid=loopback-0007) | |
| * Running swconfig command ("/usr/sbin/swconfig -f | |
| /tmp/ign_configure/software_file") for source (B7994 11i Mission | |
| Critical OE: CD4). | |
| ======= 11/06/19 02:49:57 EST BEGIN configure AGENT SESSION | |
| (pid=7025) (jobid=loopback-0008) | |
| * Agent session started for user "root@localhost". (pid=7025) | |
| ERROR: Could not apply the software selection "T2743AA"; it is not | |
| available from depot or root "loopback:/". | |
| * Beginning Analysis Phase. | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for file information. | |
| NOTE: The fileset "OS-Core.C-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN2-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.SYS-ADMIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.OBAM-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.SAM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-SRC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-RUN,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-PVT,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-PRNG,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-MIS,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-MAN,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-LIB,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-INC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-DOC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-CONF,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-CER,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset "WBEMServices.WBEM-CORE,l=/,r=A.02.00.07" is | |
| already configured. | |
| NOTE: The fileset "WBEMServices.WBEM-CORE-COM,l=/,r=A.02.00.07" is | |
| already configured. | |
| NOTE: The fileset "NParProvider.NPAR-RUN,l=/,r=B.11.11.01.04.01.01" | |
| is already configured. | |
| NOTE: The fileset "PHCO_27758.CORE-SHLIBS,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_31878.SYS-ADMIN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.APACHE,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.APACHE2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.WEBPROXY,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.PHP,l=/opt/hpws/apache,r=A.2.0.54.01" is already | |
| configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.PHP2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_PERL,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_PERL2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_JK2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_JK,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.AUTH_LDAP,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.AUTH_LDAP2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset "SysMgmtHomepage.SMH-RUN,l=/,r=A.2.2.0.4" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-RUN,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-COMMON,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| * Summary of Analysis Phase: | |
| * 36 of 75 filesets will be Skipped. | |
| * 39 of 75 filesets had no Errors or Warnings. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Configure Execution Phase. | |
| * Filesets: 39 | |
| * Running config clean command /usr/lbin/sw/config_clean. | |
| * Summary of Execution Phase: | |
| * 36 of 75 filesets were Skipped. | |
| * 39 of 75 filesets had no Errors or Warnings. | |
| * The Execution Phase succeeded. | |
| ======= 11/06/19 03:15:00 EST END configure AGENT SESSION (pid=7025) | |
| (jobid=loopback-0008) | |
| * Running swconfig command ("/usr/sbin/swconfig *"). | |
| ======= 11/06/19 03:15:21 EST BEGIN configure AGENT SESSION | |
| (pid=7407) (jobid=loopback-0009) | |
| * Agent session started for user "root@localhost". (pid=7407) | |
| * Beginning Analysis Phase. | |
| * Target: loopback:/ | |
| * Target logfile: loopback:/var/adm/sw/swagent.log | |
| * Reading source for file information. | |
| NOTE: The fileset "DCE-Core.DCE-CORE-SHLIB,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-COR-64SLIB,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-CORE-RUN,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-CORE-DTS,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-CORE-HELP,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-CORE-NOTES,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-JPN-E-MSG,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCE-JPN-S-MSG,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.DCEC-ENG-A-MAN,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DCE-Core.MACR-ENG-A-MAN,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OS-Core.C-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN2-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.SYS-ADMIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMDS-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMDS-AUX,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.ADMN-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.ADMN-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.ADMN-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.ARRAY-MGMT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.C-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.C-MIN-32ALIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.C-MIN-64ALIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.C2400-UTIL,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CAUX-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CAUX-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CAUX-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMDS-AX-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMDS-MN-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMIN-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMIN-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CMIN-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.CORE-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.HPUX-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.KERN-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.LINKER-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.NLS-AUX,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.PERL,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.Q4,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "OS-Core.RELEASE-NOTES,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.TOOL-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.TOOL-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.TOOL-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UPS-TOOLS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.USRCONTRB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-FRE-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-FRE-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-GER-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-GER-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-ITA-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-ITA-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-JPN-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-JPN-S-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-JPN-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-KOR-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-KOR-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-SCH-H-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-SCH-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-SPA-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-SPA-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-TCH-B-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-TCH-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OS-Core.UX-TCH-U-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-KRN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "NFS.NFS-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.KEY-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-64ALIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-CLIENT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NFS-PRG,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "NFS.NFS-SERVER,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NIS-CLIENT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NIS-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NIS-SERVER,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "NFS.NISPLUS-CORE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.100BT-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NETTL-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NETTL-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NETTL-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NMS-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NMS2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-RUN-64,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NET-PRG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.100BT-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NW-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.LAN-PRG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NETTL-ADM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NMS-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NW-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.NW-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Networking.PPP-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STRE-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STRE-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STRE-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-32ALIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-64ALIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.STREAMS-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.XTI-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.XTI-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams.XTI-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STRTIO2-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STRTIO-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STRTIO-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Streams-TIO.STIO-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Streams-TIO.STIO-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Streams-TIO.STIO-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INETSVCS-INETD,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INET-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INET-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INET-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INETSVCS-BOOT,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INETSVCS-DTC,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INETSVCS-INC,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.INETSVCS-RUN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.RBTD-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.RBTD-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "InternetSrvcs.RBTD-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Upgrade.UPG-TLINK,l=/opt/upgrade,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Upgrade.UPG-JPN-E-MAN,l=/opt/upgrade,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset "Upgrade.UPG-JPN-S-MAN,l=/opt/upgrade,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset "Upgrade.UPG-MAN,l=/opt/upgrade,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OVSNMPAgent.MASTER,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OVSNMPAgent.SUBAGT-HPUNIX,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OVSNMPAgent.SUBAGT-MIB2,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "OVSNMPAgent.SNMP-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OVSNMPAgent.SNMP-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OVSNMPAgent.SNMP-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-CMDS,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-AGENT,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.GZIP,l=/,r=B.11.11.0509.428" is already | |
| configured. | |
| NOTE: The fileset "SW-DIST.SD-ENG-A-MAN,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-EXAMPLES,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-FAL,l=/,r=B.11.11.0509.428" is already | |
| configured. | |
| NOTE: The fileset "SW-DIST.SD-FRE-I-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-GER-I-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-HELP,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-JPN-E-HELP,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-JPN-E-MAN,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-JPN-E-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-JPN-S-HELP,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-JPN-S-MAN,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-JPN-S-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-KOR-E-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-TCH-B-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-TCH-H-MSG,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SW-DIST.SD-UPDATE,l=/,r=B.11.11.0509.428" is | |
| already configured. | |
| NOTE: The fileset "SystemAdmin.OBAM-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.SAM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.FIRST-BOOT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.SAM-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.SAM-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SystemAdmin.OBAM-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemAdmin.SAM-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SystemAdmin.SAM-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "FCMassStorage.FCMS-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "FCMassStorage.FCMS-INIT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "FCMassStorage.FCMS-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "FCMassStorage.FCMS-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "FCMassStorage.FCMS-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "FCMassStorage.FCMS-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "FC-TACHYON-TL.FC-TL-KRN,l=/,r=B.11.11.12" is | |
| already configured. | |
| NOTE: The fileset "FC-TACHYON-TL.FC-TL-RUN,l=/,r=B.11.11.12" is | |
| already configured. | |
| NOTE: The fileset "FDDI-KRN-COM.FDDI467-KRN,l=/,r=B.11.11.01" is | |
| already configured. | |
| NOTE: The fileset "FDDI-PCI.FDDI4-KRN,l=/,r=B.11.11.02" is already | |
| configured. | |
| NOTE: The fileset "FDDI-PCI.FDAD-ENG-A-MAN,l=/,r=B.11.11.02" is | |
| already configured. | |
| NOTE: The fileset "FDDI-PCI.FDDI4-RUN,l=/,r=B.11.11.02" is already | |
| configured. | |
| NOTE: The fileset "GE-DRV.GE-KRN,l=/,r=B.11.11.19" is already | |
| configured. | |
| NOTE: The fileset "GE-DRV.GE-RUN,l=/,r=B.11.11.19" is already | |
| configured. | |
| NOTE: The fileset "JFS.VXFS-BASE-KRN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "JFS.JFS-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "JFS.JFS-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "JFS.JFS-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "JFS.VXFS-BASE-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "JFS.VXFS-PRG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "LVM.LVM-KRN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "LVM.LVM-RUN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "LVM.LVM-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "LVM.LVM-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "LVM.LVM-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "KRB-Support.KRB-SUPP-RUN,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "KRB-Support.KRB-SUPP-MAN,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "KRB-Support.KRB-SUPP-NOTES,l=/opt/dce,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset "Update-UX.UUX,l=/,r=B.11.11.0509.431" is already | |
| configured. | |
| NOTE: The fileset "Update-UX.UUX-ENG-A-MAN,l=/,r=B.11.11.0509.431" | |
| is already configured. | |
| NOTE: The fileset "Update-UX.UUX-JPN-E-MAN,l=/,r=B.11.11.0509.431" | |
| is already configured. | |
| NOTE: The fileset "Update-UX.UUX-JPN-S-MAN,l=/,r=B.11.11.0509.431" | |
| is already configured. | |
| NOTE: The fileset "PHCO_27103.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23290.KERN2-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23292.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23293.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.C-INC,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.PROG-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.PROG-AUX,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.LANG-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.LANG-64ALIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.C-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.C-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.C-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ProgSupport.PAUX-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PAUX-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PAUX-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PMIN-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PMIN-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PMIN-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PROG-AX-64ALIB,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "ProgSupport.PROG-MN-64ALIB,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "PHKL_23294.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23294.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23295.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23295.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23296.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23296.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23297.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23297.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23299.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23299.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "KernDevKit.KERN-DEV-KIT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23301.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23301.KERN-DEV-KIT,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23302.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23302.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23303.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23303.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23304.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23304.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23305.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23305.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23306.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23306.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23307.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23307.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23308.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23308.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23309.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23309.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23310.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23310.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23311.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23311.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23312.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23312.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23314.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23314.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23315.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23315.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23316.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23625.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23666.KERN2-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23810.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23957.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_24278.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_25506.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_25506.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_25506.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_26269.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_26269.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_26425.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_26425.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_26743.LVM-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_27096.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_27155.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_27219.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28025.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28025.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28025.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28197.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28197.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28569.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_28839.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29529.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29529.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29539.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29539.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29539.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29567.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29651.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29700.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29700.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_29700.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30100.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30105.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30197.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "TextFormatters.TEXT-FMT,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "TextFormatters.TEXT-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TextFormatters.TEXT-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TextFormatters.TEXT-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "PHKL_30257.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30257.FCMS-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30257.FCMS-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30257.FCMS-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30446.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30512.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_30992.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_31227.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_31241.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_31241.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_31241.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32089.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32090.ADMN-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32090.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32090.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32647.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32647.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_32647.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_33338.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_33339.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_33425.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_33425.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_33425.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_33425.KERN2-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_23288.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_23288.CORE-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_23288.NET-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_23288.NET-PRG,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_28799.100BT-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_28799.100BT-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_28799.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_30463.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_30463.KERN2-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_32396.CORE2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_32396.LAN-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_32396.LAN2-KRN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_32396.NW-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "SCSI-Passthru.SPT-DVR,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SCSI-Passthru.SPT2-DVR,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "UserLicense.UNL-USER,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27101.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27101.KERN-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27101.ADMN-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27101.KERN-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_28169.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "VRTSvxvm.VXVM-RUN,l=/,r=3.5m" is already | |
| configured. | |
| NOTE: The fileset "VRTSvxvm.VXVM-KRN,l=/,r=3.5m" is already | |
| configured. | |
| NOTE: The fileset "VRTSvxvm.VXMS,l=/,r=3.5m" is already configured. | |
| NOTE: The fileset "VRTSvxvm.VXVM-ENG-A-MAN,l=/,r=3.5m" is already | |
| configured. | |
| NOTE: The fileset "VRTSvxvm.VXVM-HELP,l=/,r=3.5m" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TT,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "CDE.CDE-MIN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "CDE.CDE-RUN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "CDE.CDE-DTTERM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-ENG-A-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-ENG-A-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-FONTS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-FRE-I-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-FRE-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-GER-I-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-GER-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-HELP-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-ICONS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-ITA-I-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-ITA-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-JPN-E-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-JPN-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-JPN-S-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-JPN-S-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-KOR-E-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-KOR-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-LANGS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SCH-H-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SCH-H-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SPA-I-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SPA-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SWE-I-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-SWE-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TCH-B-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TCH-B-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TCH-E-HELP,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CDE.CDE-TCH-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "ATOK.ATOK-RUN,l=/opt/atok,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Accounting.ACCOUNTNG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Accounting.ACCT-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Accounting.ACCT-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Accounting.ACCT-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.ASX-JPN-E-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.ASX-JPN-MAN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-Core.ASX-JPN-NOTES,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.ASX-JPN-S-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.ASX-KOR-NOTES,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.ASX-MAN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-Core.ASX-SCH-NOTES,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.ASX-TCH-NOTES,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-Core.IM-JPN-E-MAN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-Core.IM-JPN-MAN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-Core.IM-JPN-S-MAN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-PRINTER.PRNTR-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRNTR-KOR-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRNTR-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-PRINTER.PRNTR-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRNTR-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-LP-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-LP-KOR-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-LP-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-LP-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-LP-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-PD-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-PD-KOR-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-PD-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-PD-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-PRINTER.PRT-PD-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-TERM.IMTERM-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-TERM.IMTERM-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-TERM.IMTERM-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.EUS-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.EUS-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-UTILITY.MFCONV-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.STK-SCH-H-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.STK-SCH-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.STK-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.TTK-TCH-B-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.TTK-TCH-C-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.TTK-TCH-E-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.TTK-TCH-MAN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.TTK-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.UDC-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.UDC-KOR-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.UDC-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-UTILITY.UDC-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.UDC-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.UTILS-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-UTILITY.UTILS-SCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-UTILITY.UTILS-TCH-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset | |
| "ImagingSubsystem.IMAGE-SHLIBS,l=/opt/image,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "X11.X11R6-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11R5-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.MKFONTDIR,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-FONTSRV,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.MOTIF-SHLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-FONT-AUX,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-FONT-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-FRE-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-GER-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-ITA-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-JPN-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-JPN-S-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-KOR-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-RUN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "X11.X11-RUN-CL,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-RUN-CL-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-RUN-CT-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-RUN-CTRB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-RUN-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-SCH-H-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-SPA-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-SWE-I-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-TCH-B-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11-TCH-E-MSG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "X11.X11R4-SHLIBS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-INC,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-JPN-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-KOR-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-SCH-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-SHLIBS,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.IMX11-TCH-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-JPN-AUX,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-JPN-MIN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-KOR-AUX,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-KOR-BOLD,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-KOR-MIN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-SCH-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XFNT-TCH-B-AUX,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XFNT-TCH-B-MIN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XPFT-TCH-C-AUX,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XFNT-TCH-C-AUX,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XFNT-TCH-C-MIN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XPFT-TCH-E-AUX,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XFNT-TCH-E-AUX,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XFNT-TCH-E-MIN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset "Asian-X11.XJIM-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11.XP-JPN-RUN,l=/,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "Asian-X11FONTSRV.TT-JPN-RUN,l=/,r=A.03.00" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-ENG-A-MAN,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-FRE-I-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-GER-I-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-ITA-I-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-JPN-E-MAN,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-JPN-E-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-JPN-S-MAN,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-JPN-S-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-KOR-E-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-SCH-H-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-SPA-I-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-SWE-I-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-TCH-B-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUD-TCH-E-MSG,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "AudioSubsystem.AUDIO-RUN,l=/opt/audio,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset | |
| "AudioSubsystem.AUDIO-SHLIBS,l=/opt/audio,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "AudioSubsystem.AUDIO-SRV,l=/opt/audio,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset "ISEE-Java.JAVA-RUN,l=/opt,r=A.01.31.12" is | |
| already configured. | |
| NOTE: The fileset "ISEE.CORE,l=/,r=A.03.95.021" is already | |
| configured. | |
| NOTE: The fileset "ISEE-Chorus.MADHPSERVICES,l=/,r=A.5.1.395.021" is | |
| already configured. | |
| NOTE: The fileset "Availability.CODE,l=/tmp,r=0.00.00979" is already | |
| configured. | |
| NOTE: The fileset "CPS.CPS-32SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CPS.CPS-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "CPS.CPS-MIN,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "Contrib-Tools.CONTRIB,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Contrib-Tools.PDCINFO,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Contrib-Tools.PIMTOOL,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Cpumap.CODE,l=/,r=A.00.02.006" is already | |
| configured. | |
| NOTE: The fileset "Curses-Color.CURS-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Curses-Color.CURS-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Curses-Color.CURS-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Curses-Color.CURSES-MIN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Curses-Color.CURSES-PRG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "DigitalVideo.DVIDEO-SHLIBS,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DigitalVideo.DVIDEO-SRV,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "DiskQuota.DQUO-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DiskQuota.DQUO-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DiskQuota.DQUO-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DiskQuota.DQUOTA,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "DistributedPrint.PD-CLIENT,l=/opt/pd,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset "DistributedPrint.PD-COMMON,l=/opt/pd,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset | |
| "DistributedPrint.PD-ENG-A-MAN,l=/opt/pd,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "DistributedPrint.PD-JPN-E-MAN,l=/opt/pd,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "DistributedPrint.PD-JPN-S-MAN,l=/opt/pd,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "DistributedPrint.PD-SERVCOMMON,l=/opt/pd,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "DistributedPrint.PD-SPOOLER,l=/opt/pd,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset | |
| "DistributedPrint.PD-SUPERVISOR,l=/opt/pd,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "EGBridge.EGB-RUN,l=/opt/egb,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "EMS-Core.EMS-CORE,l=/,r=A.04.20" is already | |
| configured. | |
| NOTE: The fileset "EMS-Core.EMS-MX,l=/,r=A.04.20" is already | |
| configured. | |
| NOTE: The fileset "EMS-Config.EMS-GUI,l=/,r=A.04.20" is already | |
| configured. | |
| NOTE: The fileset "EMS-KRMonitor.KRMON-RUN,l=/,r=A.11.11.05" is | |
| already configured. | |
| NOTE: The fileset "EMS-KRMonitor.KRMON-DRV-CMN,l=/,r=A.11.11.05" is | |
| already configured. | |
| NOTE: The fileset "EMS-KRMonitor.KRMON-DRV-DRV,l=/,r=A.11.11.05" is | |
| already configured. | |
| NOTE: The fileset "EMS-KRMonitor.KRMON-MAN,l=/,r=A.11.11.05" is | |
| already configured. | |
| NOTE: The fileset "EMS-MIBMonitor.MIBMON-RUN,l=/,r=A.04.20" is | |
| already configured. | |
| NOTE: The fileset "GLib.GLIB-MAN,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GLib.GLIB-NOTES,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GLib.GLIB-PRG,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GLib.GLIB-SHLIBS,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GLib.GLIB-SRC,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSS-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSS-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSS-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSSAPI-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSSAPI-PRG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSSAPI-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GSS-API.GSSAPI-SHLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "GTK+.GTK+-MAN,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GTK+.GTK+-MSG,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GTK+.GTK+-NOTES,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GTK+.GTK+-PRG,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GTK+.GTK+-SHLIBS,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "GTK+.GTK+-SRC,l=/,r=1.2.10.9" is already | |
| configured. | |
| NOTE: The fileset "Gettext.GETTEXT-MAN,l=/,r=0.10.39.9" is already | |
| configured. | |
| NOTE: The fileset "Gettext.GETTEXT-MSG,l=/,r=0.10.39.9" is already | |
| configured. | |
| NOTE: The fileset "Gettext.GETTEXT-NOTES,l=/,r=0.10.39.9" is already | |
| configured. | |
| NOTE: The fileset "Gettext.GETTEXT-PRG,l=/,r=0.10.39.9" is already | |
| configured. | |
| NOTE: The fileset "Gettext.GETTEXT-SHLIBS,l=/,r=0.10.39.9" is | |
| already configured. | |
| NOTE: The fileset "Gettext.GETTEXT-SRC,l=/,r=0.10.39.9" is already | |
| configured. | |
| NOTE: The fileset | |
| "ISEE-SysInfo.SYSINFOBIN,l=/opt/hpservices/contrib,r=A.01.00.22" | |
| is already configured. | |
| NOTE: The fileset | |
| "IntegratedLogin.ILOGIN-COMMON,l=/opt/dce,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "IntegratedLogin.ILOGIN-DCE,l=/opt/dce,r=B.11.11" | |
| is already configured. | |
| NOTE: The fileset "International.ARABIC,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.BULGARIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.CHINESES,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.CHINESET,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.CZECH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.DANISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.DUTCH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.ENGLISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.FINNISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.FRENCH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.GERMAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.GREEK,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.HEBREW,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.HUNGARIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.ICELANDIC,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.ITALIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.JAPANESE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.KOREAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.NORWEGIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.POLISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.PORTUGUESE,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "International.RUMANIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.RUSSIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.SERBOCROATIAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "International.SLOVAKIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.SLOVENIAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.SPANISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.SWEDISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.THAI,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "International.TURKISH,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.STM-SHLIBS,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.RELEASE-NOTES,l=/,r=B.11.11.16.09" | |
| is already configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.STM-CATALOGS,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.STM-MAN,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.STM-UI-RUN,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Sup-Tool-Mgr.STM-UUT-RUN,l=/,r=B.11.11.16.09" is | |
| already configured. | |
| NOTE: The fileset "Isee_EmsListener.ISEE-EMSLSTNR,l=/,r=A.11.09.05" | |
| is already configured. | |
| NOTE: The fileset "Isee_EmsListener.ISEE-EMSCONF,l=/,r=A.11.09.05" | |
| is already configured. | |
| NOTE: The fileset "Jdk13.JDK13-COM,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jdk13.JDK13-DEMO,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jdk13.JDK13-PA11,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jdk13.JDK13-PA20,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jdk14.JDK14-COM,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jdk14.JDK14-DEMO,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jdk14.JDK14-PA11,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jdk14.JDK14-PA20,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jdk14.JDK14-PA20W,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jdk14.JDK14-PNV2,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jdk14.JDK14-PWV2,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jdk15.JDK15-COM,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jdk15.JDK15-DEMO,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jdk15.JDK15-PA20,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jdk15.JDK15-PA20W,l=/opt/java1.5,r=1.5.0.01.01" | |
| is already configured. | |
| NOTE: The fileset "Jdk15.JDK15-PNV2,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jdk15.JDK15-PWV2,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jpi13.JPI13-COM,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jpi13.JPI13-COM-DOC,l=/opt/java1.3,r=1.3.1.16.00" | |
| is already configured. | |
| NOTE: The fileset "Jpi13.JPI13-PA11,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jpi14.JPI14-COM,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jpi14.JPI14-COM-DOC,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jpi14.JPI14-PA11,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jre13.JRE13-COM,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jre13.JRE13-COM-DOC,l=/opt/java1.3,r=1.3.1.16.00" | |
| is already configured. | |
| NOTE: The fileset "Jre13.JRE13-PA11,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jre13.JRE13-PA11-CL,l=/opt/java1.3,r=1.3.1.16.00" | |
| is already configured. | |
| NOTE: The fileset "Jre13.JRE13-PA11-HS,l=/opt/java1.3,r=1.3.1.16.00" | |
| is already configured. | |
| NOTE: The fileset "Jre13.JRE13-PA20,l=/opt/java1.3,r=1.3.1.16.00" is | |
| already configured. | |
| NOTE: The fileset "Jre13.JRE13-PA20-CL,l=/opt/java1.3,r=1.3.1.16.00" | |
| is already configured. | |
| NOTE: The fileset "Jre13.JRE13-PA20-HS,l=/opt/java1.3,r=1.3.1.16.00" | |
| is already configured. | |
| NOTE: The fileset "Jre14.JRE14-COM,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jre14.JRE14-COM-DOC,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jre14.JRE14-PA11,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jre14.JRE14-PA11-HS,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jre14.JRE14-PA20,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jre14.JRE14-PA20-HS,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jre14.JRE14-PA20W,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset | |
| "Jre14.JRE14-PA20W-HS,l=/opt/java1.4,r=1.4.2.09.02" is already | |
| configured. | |
| NOTE: The fileset "Jre14.JRE14-PNV2,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jre14.JRE14-PNV2-H,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jre14.JRE14-PWV2,l=/opt/java1.4,r=1.4.2.09.02" is | |
| already configured. | |
| NOTE: The fileset "Jre14.JRE14-PWV2-H,l=/opt/java1.4,r=1.4.2.09.02" | |
| is already configured. | |
| NOTE: The fileset "Jre15.JRE15-COM,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jre15.JRE15-COM-DOC,l=/opt/java1.5,r=1.5.0.01.01" | |
| is already configured. | |
| NOTE: The fileset "Jre15.JRE15-PA20,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jre15.JRE15-PA20-HS,l=/opt/java1.5,r=1.5.0.01.01" | |
| is already configured. | |
| NOTE: The fileset "Jre15.JRE15-PA20W,l=/opt/java1.5,r=1.5.0.01.01" | |
| is already configured. | |
| NOTE: The fileset | |
| "Jre15.JRE15-PA20W-HS,l=/opt/java1.5,r=1.5.0.01.01" is already | |
| configured. | |
| NOTE: The fileset "Jre15.JRE15-PNV2,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jre15.JRE15-PNV2-H,l=/opt/java1.5,r=1.5.0.01.01" | |
| is already configured. | |
| NOTE: The fileset "Jre15.JRE15-PWV2,l=/opt/java1.5,r=1.5.0.01.01" is | |
| already configured. | |
| NOTE: The fileset "Jre15.JRE15-PWV2-H,l=/opt/java1.5,r=1.5.0.01.01" | |
| is already configured. | |
| NOTE: The fileset "Judy-lib.JUDY,l=/,r=B.11.11.04.13" is already | |
| configured. | |
| NOTE: The fileset "Judy-lib.JUDY-COMMON,l=/,r=B.11.11.04.13" is | |
| already configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-64SLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-PRG,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "KRB5-Client.KRB5-SHLIB,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Keyshell.KEYS-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Keyshell.KEYS-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Keyshell.KEYS-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Keyshell.KEYSHELL-RUN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "LSSERV.LSRV-ENG-A-MAN,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "LSSERV.LSRV-JPN-E-MAN,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "LSSERV.LSRV-JPN-S-MAN,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "LSSERV.LSSERV-ADMIN,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "LSSERV.LSSERV-RUN,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "LSSERV.LSSERV-SERVER,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "LSSERV.LSSERV-SHLIBS,l=/opt/ifor,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "LdapUxClient.ADMIN-RUN,l=/opt/ldapux,r=B.04.00.02" is already | |
| configured. | |
| NOTE: The fileset "LdapUxClient.CORE-RUN,l=/opt/ldapux,r=B.04.00.02" | |
| is already configured. | |
| NOTE: The fileset | |
| "LdapUxClient.LDAP-C-SDK,l=/opt/ldapux,r=B.04.00.02" is | |
| already configured. | |
| NOTE: The fileset | |
| "LdapUxClient.LDUX-ENG-A-MAN,l=/opt/ldapux,r=B.04.00.02" is | |
| already configured. | |
| NOTE: The fileset | |
| "LdapUxClient.NATIVELDAP-RUN,l=/opt/ldapux,r=B.04.00.02" is | |
| already configured. | |
| NOTE: The fileset | |
| "LdapUxClient.PAM-AUTHZ-RUN,l=/opt/ldapux,r=B.04.00.02" is | |
| already configured. | |
| NOTE: The fileset "Libiconv.LICONV-MAN,l=/,r=1.6.1.9" is already | |
| configured. | |
| NOTE: The fileset "Libiconv.LICONV-NOTES,l=/,r=1.6.1.9" is already | |
| configured. | |
| NOTE: The fileset "Libiconv.LICONV-PRG,l=/,r=1.6.1.9" is already | |
| configured. | |
| NOTE: The fileset "Libiconv.LICONV-RUN,l=/,r=1.6.1.9" is already | |
| configured. | |
| NOTE: The fileset "Libiconv.LICONV-SHLIBS,l=/,r=1.6.1.9" is already | |
| configured. | |
| NOTE: The fileset "Libiconv.LICONV-SRC,l=/,r=1.6.1.9" is already | |
| configured. | |
| NOTE: The fileset "MCPS-COMMON.BIN,l=/,r=A.01.01.01" is already | |
| configured. | |
| NOTE: The fileset "MSDOS-Utils.DOS-UTILS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "MSDOS-Utils.DOSU-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "MSDOS-Utils.DOSU-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "MSDOS-Utils.DOSU-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "MailUtilities.MAIL-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "MailUtilities.MAIL-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "MailUtilities.MAIL-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "MailUtilities.MAILERS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Mozilla.MOZ-COM,l=/opt/mozilla,r=1.7.8.00.00" is | |
| already configured. | |
| NOTE: The fileset "Mozilla.MOZ-COM-DOC,l=/opt/mozilla,r=1.7.8.00.00" | |
| is already configured. | |
| NOTE: The fileset "Mozilla.MOZ-PA11,l=/opt/mozilla,r=1.7.8.00.00" is | |
| already configured. | |
| NOTE: The fileset "MozillaSrc.MOZ-SRC,l=/opt/mozilla,r=1.7.8.00.00" | |
| is already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-SRC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-RUN,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-PVT,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-PRNG,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-MIS,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-MAN,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-LIB,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-INC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-DOC,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-CONF,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset | |
| "openssl.OPENSSL-CER,l=/opt/openssl,r=A.00.09.07e.012" is | |
| already configured. | |
| NOTE: The fileset "WBEMServices.WBEM-CORE,l=/,r=A.02.00.07" is | |
| already configured. | |
| NOTE: The fileset "WBEMServices.WBEM-CORE-COM,l=/,r=A.02.00.07" is | |
| already configured. | |
| NOTE: The fileset "WBEMServices.WBEM-MAN,l=/,r=A.02.00.07" is | |
| already configured. | |
| NOTE: The fileset "WBEMServices.WBEM-MX,l=/,r=A.02.00.07" is already | |
| configured. | |
| NOTE: The fileset "NParProvider.NPAR-DOC,l=/,r=B.11.11.01.04.01.01" | |
| is already configured. | |
| NOTE: The fileset "NParProvider.NPAR-RUN,l=/,r=B.11.11.01.04.01.01" | |
| is already configured. | |
| NOTE: The fileset "NPartition.NPAR-ENG-A-MAN,l=/,r=A.01.02" is | |
| already configured. | |
| NOTE: The fileset "NPartition.NPARCMDS-RUN,l=/,r=A.01.02" is already | |
| configured. | |
| NOTE: The fileset | |
| "NisLdapServer.YPLDAP-SERVER,l=/opt/ldapux,r=B.04.00.02" is | |
| already configured. | |
| NOTE: The fileset "NonHP-Terminfo.NONHPTERM,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "OBAM.OBAM-BIN,l=/,r=B.11.00.05.3.06" is already | |
| configured. | |
| NOTE: The fileset "OBAM.OBAM-JVM,l=/,r=B.11.00.05.3.06" is already | |
| configured. | |
| NOTE: The fileset "OBAM.OBAM-WEB,l=/,r=B.11.00.05.3.06" is already | |
| configured. | |
| NOTE: The fileset "PHCO_22958.FIRST-BOOT,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_23263.ADMN-ENG-A-MAN,l=/,r=B.11.11.15" is | |
| already configured. | |
| NOTE: The fileset "PHCO_23263.ARRAY-MGMT,l=/,r=B.11.11.15" is | |
| already configured. | |
| NOTE: The fileset "PHCO_24173.ADMN-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_24173.UPS-TOOLS,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_25311.ADMN-ENG-A-MAN,l=/,r=B.11.11.15" is | |
| already configured. | |
| NOTE: The fileset "PHCO_25311.ARRAY-MGMT,l=/,r=B.11.11.15" is | |
| already configured. | |
| NOTE: The fileset "PHCO_25831.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_26951.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27100.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27185.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_27758.CORE-SHLIBS,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_28160.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_28998.SYS-ADMIN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_28998.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_29379.LVM-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_29379.LVM-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30514.ADMN-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30514.CORE-SHLIBS,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30514.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30598.INETSVCS-BOOT,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30598.SAM,l=/,r=1.0" is already configured. | |
| NOTE: The fileset "PHCO_30598.SAM-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30598.SAM-HELP,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_30598.UX-CORE,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_31878.CORE-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHCO_31878.SYS-ADMIN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23298.KERN-DEV-KIT,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_23300.KERN-DEV-KIT,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_27177.ADMN-ENG-A-MAN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHKL_27177.KERN-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHNE_23289.C-INC,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHSS_22898.CORE-64SLIB,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHSS_22898.CORE-SHLIBS,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHSS_22898.LANG-64ALIB,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHSS_22898.LANG-MIN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "PHSS_25983.KERN-RUN,l=/,r=1.0" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-RECORD,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-MBX,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-HPCR-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-HPCR,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-DPMS-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-DPMS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-DBE-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.XEXT-DBE,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.X11-SERV-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.X11-SERV,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.DDX-UTILS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.DDX-SLS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.DDX-SAM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.DDX-LOAD,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.DDX-ENTRY,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.DDX-ADVANCED,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Xserver.AGRM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.AGRM,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.DDX-ADVANCED,l=/,r=B.11.11.29" is | |
| already configured. | |
| NOTE: The fileset "PHSS_32939.DDX-ENTRY,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.DDX-LOAD,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.DDX-SAM,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.DDX-SLS,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.DDX-UTILS,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.X11-SERV,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.X11-SERV-MAN,l=/,r=B.11.11.29" is | |
| already configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-DBE,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-DBE-MAN,l=/,r=B.11.11.29" is | |
| already configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-DPMS,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-DPMS-MAN,l=/,r=B.11.11.29" is | |
| already configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-HPCR,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-HPCR-MAN,l=/,r=B.11.11.29" is | |
| already configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-MBX,l=/,r=B.11.11.29" is already | |
| configured. | |
| NOTE: The fileset "PHSS_32939.XEXT-RECORD,l=/,r=B.11.11.29" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.APACHE,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.APACHE2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.WEBPROXY,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.PHP,l=/opt/hpws/apache,r=A.2.0.54.01" is already | |
| configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.PHP2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_PERL,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_PERL2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_JK2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.MOD_JK,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.AUTH_LDAP,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsAPACHE.AUTH_LDAP2,l=/opt/hpws/apache,r=A.2.0.54.01" is | |
| already configured. | |
| NOTE: The fileset "SysMgmtHomepage.SMH-RUN,l=/,r=A.2.2.0.4" is | |
| already configured. | |
| NOTE: The fileset "SysMgmtHomepage.SMH-DOC,l=/,r=A.2.2.0.4" is | |
| already configured. | |
| NOTE: The fileset "SysMgmtHomepage.SMH-DOC-COM,l=/,r=A.2.2.0.4" is | |
| already configured. | |
| NOTE: The fileset "SysMgmtHomepage.SMH-UILIB,l=/,r=A.2.2.0.4" is | |
| already configured. | |
| NOTE: The fileset "SysMgmtHomepage.SMH-UILIB-COM,l=/,r=A.2.2.0.4" is | |
| already configured. | |
| NOTE: The fileset | |
| "PartitionManager.PARMGR,l=/,r=B.11.11.02.00.05.03" is already | |
| configured. | |
| NOTE: The fileset | |
| "PartitionManager.PARMGR-HELP,l=/,r=B.11.11.02.00.05.03" is | |
| already configured. | |
| NOTE: The fileset | |
| "PartitionManager.PARMGR-MAN,l=/,r=B.11.11.02.00.05.03" is | |
| already configured. | |
| NOTE: The fileset | |
| "PartitionManager.PARMGR-RUN,l=/,r=B.11.11.02.00.05.03" is | |
| already configured. | |
| NOTE: The fileset "Perl5-32.PERL-MAN,l=/opt/perl,r=D.5.8.3.B" is | |
| already configured. | |
| NOTE: The fileset "Perl5-32.PERL-RUN,l=/opt/perl,r=D.5.8.3.B" is | |
| already configured. | |
| NOTE: The fileset "Perl5-64.PERL-MAN,l=/opt/perl_64,r=D.5.8.3.B" is | |
| already configured. | |
| NOTE: The fileset "Perl5-64.PERL-RUN,l=/opt/perl_64,r=D.5.8.3.B" is | |
| already configured. | |
| NOTE: The fileset "PrinterMgmt.LP-SPOOL,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "PrinterMgmt.LPSP-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "PrinterMgmt.LPSP-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "PrinterMgmt.LPSP-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SOE.SOE,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "SOE.SOE-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SOE.SOE-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SOE.SOE-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "Secure_Shell.SECURE_SHELL,l=/opt/ssh,r=A.04.00.002" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.AUDT-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.AUDT-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.AUDT-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.SEC-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.SEC-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.SEC-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SecurityMon.SECURITY,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SourceControl.SRC-CNTL,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SourceControl.SRC-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SourceControl.SRC-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SourceControl.SRC-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "Spelling.SPEL-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Spelling.SPEL-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Spelling.SPEL-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "Spelling.SPELL,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "SystemComm.SYSC-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SystemComm.SYSC-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SystemComm.SYSC-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "SystemComm.SYSCOM,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "TechPrintServ.TPS-C-HELP,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-C-SERV,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-FONTS,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-FRE-I-HELP,l=/,r=B.11.11.0412" | |
| is already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-FRE-I-SERV,l=/,r=B.11.11.0412" | |
| is already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-GER-I-HELP,l=/,r=B.11.11.0412" | |
| is already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-GER-I-SERV,l=/,r=B.11.11.0412" | |
| is already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-JPN-E-HELP,l=/,r=B.11.11.0412" | |
| is already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-JPN-S-HELP,l=/,r=B.11.11.0412" | |
| is already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-MAN,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-MIN,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-RELNOTES,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-SERV,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TechPrintServ.TPS-SHLIBS,l=/,r=B.11.11.0412" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TERM-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TERM-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TERM-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TERM-MNGR-MIN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TERM-MNGR-NHP,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TSM-FRE-I-MSG,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TerminalMngr.TSM-GER-I-MSG,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TextEditors.EDIT-ENG-A-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TextEditors.EDIT-JPN-E-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TextEditors.EDIT-JPN-S-MAN,l=/,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset "TextEditors.EDITORS,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "UUCP.UUCP,l=/,r=B.11.11" is already configured. | |
| NOTE: The fileset "UUCP.UUCP-ENG-A-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "UUCP.UUCP-JPN-E-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "UUCP.UUCP-JPN-S-MAN,l=/,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "VJE.VJE-RUN,l=/opt/vje,r=A.03.00" is already | |
| configured. | |
| NOTE: The fileset "VParProvider.VPAR-DOC,l=/,r=B.11.11.01.01" is | |
| already configured. | |
| NOTE: The fileset "VParProvider.VPAR-RUN,l=/,r=B.11.11.01.01" is | |
| already configured. | |
| NOTE: The fileset "VRTSob.VEAS-FILESET,l=/,r=3.0.2.261a" is already | |
| configured. | |
| NOTE: The fileset "VRTSfspro.FSPRO-PRG,l=/,r=3.5-ga08" is already | |
| configured. | |
| NOTE: The fileset "VRTSobgui.VEA-FILESET,l=/,r=3.0.2.261a" is | |
| already configured. | |
| NOTE: The fileset "VRTSvlic.VLIC-RUN,l=/,r=3.00.007e" is already | |
| configured. | |
| NOTE: The fileset "VRTSvmdoc.VXVM-DOC,l=/,r=3.5m" is already | |
| configured. | |
| NOTE: The fileset "VRTSvmpro.VMPRO-PRG,l=/opt/VRTSvmpro,r=3.5m" is | |
| already configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-ENG-A-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-FRE-I-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-GER-I-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-ITA-I-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-JPN-E-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-JPN-S-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-KOR-E-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset "VUEtoCDE.V2C-RUN,l=/opt/Migration,r=B.11.11" is | |
| already configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-SCH-H-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-SPA-I-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-SWE-I-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-TCH-B-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "VUEtoCDE.V2C-TCH-E-MSG,l=/opt/Migration,r=B.11.11" is already | |
| configured. | |
| NOTE: The fileset | |
| "hpuxwsTOMCAT.TOMCAT,l=/opt/hpws/tomcat,r=A.5.5.9.01" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsWEBMIN.WEBMIN,l=/opt/hpws/webmin,r=A.1.070.04" is | |
| already configured. | |
| NOTE: The fileset | |
| "hpuxwsWEBMIN.HPDOCS,l=/opt/hpws/webmin,r=A.1.070.04" is | |
| already configured. | |
| NOTE: The fileset "hpuxwsXML.XMLTOOLS,l=/opt/hpws/xmltools,r=A.2.00" | |
| is already configured. | |
| NOTE: The fileset "hpuxwsXML.BATIK,l=/opt/hpws/xmltools,r=A.2.00" is | |
| already configured. | |
| NOTE: The fileset "hpuxwsXML.COCOON,l=/opt/hpws/xmltools,r=A.2.00" | |
| is already configured. | |
| NOTE: The fileset "hpuxwsXML.FOP,l=/opt/hpws/xmltools,r=A.2.00" is | |
| already configured. | |
| NOTE: The fileset "hpuxwsXML.XALANJ,l=/opt/hpws/xmltools,r=A.2.00" | |
| is already configured. | |
| NOTE: The fileset "hpuxwsXML.XERCESJ,l=/opt/hpws/xmltools,r=A.2.00" | |
| is already configured. | |
| NOTE: The fileset "iCOD.ICOD-RUN,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-COMMON,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-ENG-A-MAN,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-FCA-I-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-FCA-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-FRE-I-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-FRE-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-GER-I-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-GER-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-HKG-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-ITA-I-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-ITA-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-JPN-E-MAN,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-JPN-E-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-JPN-S-MAN,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-JPN-S-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-JPN-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-KOR-E-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-KOR-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-SCH-H-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-SCH-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-SPA-I-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-SPA-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-TCH-B-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-TCH-E-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| NOTE: The fileset "iCOD.ICOD-TCH-U-MSG,l=/,r=B.11.11.07.01.00.00" is | |
| already configured. | |
| * Summary of Analysis Phase: | |
| * 948 of 948 filesets will be Skipped. | |
| * The Analysis Phase succeeded. | |
| * Beginning the Configure Execution Phase. | |
| * Filesets: 0 | |
| * Running config clean command /usr/lbin/sw/config_clean. | |
| * Summary of Execution Phase: | |
| * 948 of 948 filesets were Skipped. | |
| * The Execution Phase succeeded. | |
| ======= 11/06/19 03:20:47 EST END configure AGENT SESSION (pid=7407) | |
| (jobid=loopback-0009) | |
| * Run_SD_Configure_Scripts: Complete | |
| * Run_Postconfigure_Scripts: Begin | |
| * Applying the networking information. | |
| * Creating the manifest. | |
| * Run all specified post-configure scripts. | |
| * Run_Postconfigure_Scripts: Complete | |
| ======= 11/06/19 03:21:24 EST Installation complete: Successful | |
| ####### # # | |
| # # # # | |
| # # # # | |
| # # ### | |
| # # # # | |
| # # # # | |
| ####### # # | |
| NOTE: Rebooting system. | |
| sync'ing disks (0 buffers to flush): | |
| 0 buffers not flushed | |
| 0 buffers still dirty | |
| Closing open logical volumes... | |
| Done | |
| SeaBIOS wants SYSTEM HALT. | |
| Connection closed by foreign host. | |
| [localuser@dell-poweredge-2950 ~/Qemu-VirtualMachines/hpux]$ exit | |
| Script done on Wed Nov 6 08:43:49 2019 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment