m600 for fluidd

[gcode_macro BACK]
gcode:
     M876 S1 
[gcode_macro NEXT]
gcode:
     m876 S2
[gcode_macro CANCEL]
gcode:
     m876 S1

[gcode_macro EXTRACT]
gcode:
     m876 S3

############################################u
############################################u
############################################u

#------------------------------------------------------u
# MOM - My Overpowered M600 macro / written by Jay Lexx
# Also tenderly called the Mother Of Macros by u/Woodcat64  
# Listen to MOM and everything will be alright!
#------------------------------------------------------
#  NO RESPONSE TAKEN FOR ANY DAMAGE CAUSED BY MOM ;)
#------------------------------------------------------
# 
#
# 09.11.2021 v0.1.6
#
# Sourcecode maintenance due to Klipper updates.
#
# v0.1.5
#
# - added ability to prevent nozzle cooldown
#
# Save this file f.e. as /home/pi/klipper_config/m600.cfg to leave printer.cfg nice and clean
# then use [include /home/pi/klipper_config/M600.cfg] in your printer.cfg
# Don't forget to configure default values in [gcode_makro m600cfg] down below
# 
#
# Usage in CURA Slicer:
# Extensions > Post Processing > Modify G-Code
#	Add a script -> Filament Change
#			Set Layer to value at which filament should be changed
#			I personally set the rest to 0, works like a charm
#			( Tbh, i even didn't check if they have any effect ) 
#
# The M600 command can also be used to just change filament from console or via Button, so, 
# no more need for Unload,Park, Load etc. Macros anymore. The macro should return to the temp
# the printer had when it was started, regardless ff printer temperature at 0, 40 or 200
# It will check if temperature is high enough to extrude filament ( you have configured your 
# min_extrude_temp in printer.cfg [extruder] didn't you ?!?), if not it will use the default 
# temperature configured down below anyway.
# 
#
# If the printer was not homed - therefore not knowing where it is - it will perform 
# a G28 homing sequence . This will ( better say should ;) ) not happen mid print, don't worry. 
# 
# -----------------------------------------------------
#  DESIGNED TO WORK ESPECIALLY WITH OCTOPRINT
# -----------------------------------------------------
# In Octoprint set Plugins -> Printer Dialogs -> Enable Support = Always
# Thx to u/josolanes for mentioning the fix for this possible issue
#
# Please apologize my english, i'm not a native speaker :)
#
# Those macros are in the magic box:
#
# [M876 S]
# Handle prompt response ( to communicate with octoprint )
#
# [JOBCENTER]
# Handles navigation inside the whole process ( better not to issue as terminal command )
#
# [M125]
# Park head
#
# [M701]
# Load filament
#
# [M702]
# Unload filament
#
# [LOW_TEMP_CHECK T]
# Heatup process & temperature processor
# uses printer.cfg [extruder] section max_temp & min_extrude_temp
#
# [M600]
# Marlin compatible guided Filament Change

#-------------------------------------------------------------------------

# Delete sections [respond] and [pause_resume] if already in your printer.cfg
# Both are needed to make MOM run the household and use social media ;)
#-------------------------------------------------------------------------

[pause_resume]
recover_velocity: 100
#   When capture/restore is enabled, the speed at which to return to
#   the captured position (in mm/s). Default is 50.0 mm/s.

[respond]
#default_type: echo
#   Sets the default prefix of the "M118" and "RESPOND" output to one
#   of the following:
#       echo: "echo: " (This is the default)
#       command: "// "
#       error: "!! "
#default_prefix: echo:
#   Directly sets the default prefix. If present, this value will
#   override the "default_type".

#-------------------------------------------------------------------------

#####################
[gcode_macro m600cfg]
#####################

# CONFIGURE YOUR PREFERRED DEFAULT VALUES INSIDE THIS GCODE_MACRO
# Couldn't find anywhere if or how it's possible to define a config section
# Would have been much nicer to deal with, maybe one day i'll find out :)
# Leave me a hint if you know how.

variable_default_temp: 220
# Default temperature to heat up if M600 issued in terminal
# Ignored if a target temperature is already set at launch ( M104 / M109 )
# or started within a printjob

variable_cooldown: 1
# Wether the hotende should cool down or not when pause started
# 1 - Hotend cools down when paused ( Recommended for security reasons and saves some energy if 
#     you're away a longer period of time and therefore can't change the filament)
# 0 - Hotend stays hot ( Not recommended, you never know... )

variable_x: 300
variable_y: 150
# Coordinates to park hotend at (as absolute values)

variable_z: 10
# mm to raise z from current height (this is a relative value!)

variable_zmin: 70
# if current z height is below zmin (as an absolute value), head will lift zmin ( as relative value) instead z
# making it easier to clean the nozzle at that height

variable_load_fast: 6
# mm to load filament at fast speed (length of bowden-hotend-purge)

variable_load_slow: 1
# mm to load filament after fast speed slowly into the hotend incl. purge

variable_bowden: 25
# total mm to unload filament (all at high speed)

variable_speed_1: 6000
# Speed at which filament is loaded/unloaded

variable_speed_2: 9000
# Speed at which hotend is moved to park position

variable_purge: 20
# Possibility to extract xx mm filament after loading if loading was too short f.e.

variable_output: 118
#Additional output send via M117 or M118

# !-ATTENTION--------------------------------------------------------!
# !								     !
# ! Uncomment the desired language / Comment ( Delete ) the other    !
# ! If you edit the language please don't use special characters     !
# ! like Ü,Ö,Ä, Ǣ or É in your language,macro will not work and show !
# ! a UnicodeDecodeError: 'ascii' ... 		                     !
# !------------------------------------------------------------------!

# Textdata HTML UI deutsch (german)
#variable_step_a1: "<CENTER><P><B>SCHRITT 1/3 </B></P><H2>ZEIT ZU WECHSELN</H2>"
#variable_step_b1:"Achtung, der Druckkopf ist ggfs. heiss!<dl><dt>"
#variable_step_c1:"Die Temperatur wurde zur Sicherheit auf 0 gesetzt<dl><dt>"
#variable_step_d1:"Klicke <b>WEITER</B> um (wieder) aufzuheizen<BR> Klipper wird anschliessend das Filament entladen<BR><BR>"

#variable_step_2: "<CENTER><P><B>SCHRITT 2/3</B></P><B>Lade jetzt das neue Filament und klicke auf WEITER<BR><BR>( +/- 10mm in den PTFE Schlauch)"
#variable_step_3: "<CENTER><P><B>SCHRITT 3/3</B></P><B>Reinige den Druckkopf, klicke dann WEITER um mit dem Druck fortzufahren oder ZURUECK um zum vorherigen Schritt 2 zu gelangen."
#variable_next: "WEITER"
#variable_previous: "ZURUECK"
#variable_cancel: "ABBRUCH"
#variable_purgetext: "EXTRAHIERE"

# Textdata HTML UI english
variable_step_a1: "<CENTER><P><B>STEP 1/3 </B></P><H2>TIME TO CHANGE</H2>"
variable_step_b1:"Beware, the nozzle could be hot! <dl><dt>"
variable_step_c1:"Temperature set to 0 for security reasons<dl><dt>"
variable_step_d1:"Click <b>NEXT</B> to heat up (again)<BR> Klipper will then unload the filament<BR><BR>"
variable_step_2: "<CENTER><P><B>STEP 2/3</B></P><B>Load the new filament and click NEXT<BR><BR>( +/- 10mm into PTFE tube)"
variable_step_3: "<CENTER><P><B>STEP 3/3</B></P><B>Wipe nozzle clean, then click NEXT to resume print or click BACK to unload again and return to step 2"
variable_next: "NEXT"
variable_previous: "BACK"
variable_cancel: "CANCEL"
variable_purgetext: "EXTRACT"

gcode:

  #-# * * * THERE SHOULD BE NO NEED TO EDIT ANYTHING BELOW THIS POINT * * * #-#

  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=default_temp VALUE={default_temp}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=cooldown VALUE={cooldown}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=x VALUE={x}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=y VALUE={y}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=z VALUE={z}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=zmin VALUE={zmin}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=retract_fast VALUE={retract_fast}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=retract_slow VALUE={retract_slow}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=speed_1 VALUE={speed_1}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=speed_2 VALUE={speed_2}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=purge VALUE={purge}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=output VALUE={output}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=step_a1 VALUE={step_a1}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=step_b1 VALUE={step_b1}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=step_v1 VALUE={step_c1}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=step_d1 VALUE={step_d1}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=step_2 VALUE={step_2}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=step_3 VALUE={step_3}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=next VALUE={next}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=previous VALUE={previous}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=cancel VALUE={cancel}
  SET_GCODE_VARIABLE MACRO=m600cfg VARIABLE=purgetext VALUE={purgetext}


#####################
[gcode_macro M876]
#####################

variable_myjob: 0

gcode:

	{% set S = params.S|default(-1)|int %}
	{% set myjob = printer["gcode_macro JOBCENTER"].job %}
	{% if  myjob != 0 %}

		{% if S == 1 %}
			{% set myjob = myjob-2 %}	#Jump to previous Step
          {% elif S == 2%}
               
          {% elif S == 3%}
               {% if myjob == 6003 %}
                    {% set myjob = 6004 %}
               {% else %}
                    {% set myjob = 6003 %}
               {% endif %}
          {% endif %}
          
          {% if myjob == 5999 %}
               JOBCENTER NEWJOB=5999
          {% elif myjob == 6001%}
               JOBCENTER NEWJOB=6001
          {% elif myjob == 6002%}
               JOBCENTER NEWJOB=6002
          {% elif myjob == 6003%}
               JOBCENTER NEWJOB=6003
          {% elif myjob == 6004%}
               JOBCENTER NEWJOB=6004
		{% endif %}

        	

	{% endif %}




#######################
[gcode_macro JOBCENTER]
#######################

variable_temperature: 0
variable_job: 0
variable_myjob: 0
variable_cool: 1
variable_mystep: 1

gcode:
      RESPOND TYPE=echo MSG="Jobcenter recieved: {params.NEWJOB} "
	{% set NEWJOB = params.NEWJOB|default(0)|int %}
     
	{% set myjob = printer["gcode_macro JOBCENTER"].job %}

	{% if NEWJOB == 6004 %}

		M{printer["gcode_macro m600cfg"].output|int} Extracting ...
		M83
    		G92 E0.0
          G1 E{printer["gcode_macro m600cfg"].purge|int} F200
          G92 E0.0

		{% set NEWJOB=6005 %}

	{% endif %}

	{% if NEWJOB == 6003 %}

          M{printer["gcode_macro m600cfg"].output|int} Restoring printer state

          {% if printer["gcode_macro JOBCENTER"].temperature==0 %}

		     M109 S0

          {% else %}

               M109 S{printer["gcode_macro JOBCENTER"].temperature}

          {% endif%}

	RESUME
     RESPOND TYPE=command MSG="action:notification Resuming print..."

	{% set myjob=0 %}

	{% endif %}

	{% if ( NEWJOB == 6002 or NEWJOB == 6005) %}

		{% if NEWJOB==6002 %}
			M{printer["gcode_macro m600cfg"].output|int} Loading filament
			M701

		{% endif %}

		RESPOND TYPE=command MSG="action:prompt_begin {printer["gcode_macro m600cfg"].step_3}"
		RESPOND TYPE=command MSG="action:prompt_choice {printer["gcode_macro m600cfg"].next}"
		RESPOND TYPE=command MSG="action:prompt_choice {printer["gcode_macro m600cfg"].previous}"
		RESPOND TYPE=command MSG="action:prompt_choice {printer["gcode_macro m600cfg"].purgetext} {printer["gcode_macro m600cfg"].purge|int} mm"
		RESPOND TYPE=command MSG="action:prompt_show"

          {% set myjob=6003 %}

	{% endif %}

	{% if NEWJOB == 6001 %}
          RESPOND TYPE=echo MSG="6001 entered"
		LOW_TEMP_CHECK T={printer["gcode_macro JOBCENTER"].temperature}
          RESPOND TYPE=echo MSG="emptying filament"
		M{printer["gcode_macro m600cfg"].output|int} Unloading filament
		M702
		RESPOND TYPE=command MSG="action:prompt_begin {printer["gcode_macro m600cfg"].step_2}"
          RESPOND TYPE=command MSG="action:prompt_choice {printer["gcode_macro m600cfg"].next}"
		RESPOND TYPE=command MSG="action:prompt_show"
          RESPOND TYPE=echo MSG="setting 6002"
          {% set myjob=6002 %}

	{% endif %}

	{% if NEWJOB == 5999 %}

          M{printer["gcode_macro m600cfg"].output|int} Restoring printer state

          {% if printer["gcode_macro JOBCENTER"].temperature != 0 %}

			LOW_TEMP_CHECK T={printer["gcode_macro JOBCENTER"].temperature} OVERRIDE=1

		{% endif %}

	     RESUME
          RESPOND TYPE=command MSG="action:notification M600 cancelled"

		{% set myjob=0 %}

	{% endif %}

	{% if NEWJOB == 600 %}

		PAUSE
		M125
		{% set cool=printer["gcode_macro m600cfg"].cooldown|int %}
		{% set mystep=[printer["gcode_macro m600cfg"].step_a1,printer["gcode_macro m600cfg"].step_b1,printer["gcode_macro m600cfg"].step_d1]|join() %}
		{% if cool != 0 %}

			M104 S0
			{% set mystep=[printer["gcode_macro m600cfg"].step_a1,printer["gcode_macro m600cfg"].step_c1,printer["gcode_macro m600cfg"].step_d1]|join() %}

		{% endif %}

		SET_IDLE_TIMEOUT TIMEOUT=7200
		
		RESPOND TYPE=command MSG="action:prompt_begin {mystep}"
		RESPOND TYPE=command MSG="action:prompt_choice {printer["gcode_macro m600cfg"].next}"
		RESPOND TYPE=command MSG="action:prompt_choice {printer["gcode_macro m600cfg"].cancel}"
		RESPOND TYPE=command MSG="action:prompt_show"

          {% set myjob=6001 %}

	{% endif %}

	SET_GCODE_VARIABLE MACRO=JOBCENTER VARIABLE=job VALUE={myjob}


##################
[gcode_macro M125]
##################

gcode:

	M{printer["gcode_macro m600cfg"].output|int} Moving hotend to {printer["gcode_macro m600cfg"].x|int}, {printer["gcode_macro m600cfg"].y|int}, {printer["gcode_macro m600cfg"].z|int} ({printer["gcode_macro m600cfg"].zmin|int})
	SET_GCODE_VARIABLE MACRO=JOBCENTER VARIABLE=temperature VALUE={printer.extruder.target}

	{% if printer.toolhead.homed_axes != "xyz" %}
	# if  not yet homed

		M{printer["gcode_macro m600cfg"].output|int} Probably not printing. Homing needed ...
		G28

	{% endif %}

     G91

#    	Note to self: Uncomment if ooze experienced (untested yet, just a logical thought)
#	Retract small amount before moving if printer has a temperature set
	{% if printer.extruder.target != 0 %}

		LOW_TEMP_CHECK
        	G1 E-2 F1500

	{% endif %}

	{% if printer.toolhead.position.z|float + printer["gcode_macro m600cfg"].z|float < printer.configfile.config["stepper_z"]["position_max"]|float %}

		{% if  printer.toolhead.position.z < printer["gcode_macro m600cfg"].zmin|int %}

        	  G1 Z{printer["gcode_macro m600cfg"].zmin|int|int-printer.toolhead.position.z|int}

		{% else %}

          	SAVE_GCODE_STATE NAME=save_state
          	G1 Z{printer["gcode_macro m600cfg"].z|int}
               RESTORE_GCODE_STATE NAME=save_state

     	  	{% endif %}

	{% endif%}


	G90
	G1 X{printer["gcode_macro m600cfg"].x|int} Y{printer["gcode_macro m600cfg"].y|int} F{printer["gcode_macro m600cfg"].speed_2|int}

##################
[gcode_macro M701]
##################

gcode:

     M83
     G92 E0.0
     LOW_TEMP_CHECK
     G1 E{printer["gcode_macro m600cfg"].load_fast|int} F{printer["gcode_macro m600cfg"].speed_1|int}
     G92 E0.0
     G1 E{printer["gcode_macro m600cfg"].load_slow|int} F200
     G92 E0.0


##################
[gcode_macro M702]
##################

gcode:

     LOW_TEMP_CHECK
     G91
     G1 E10 F1200
     G1 E-{printer["gcode_macro m600cfg"].bowden|int} F{printer["gcode_macro m600cfg"].speed_1|int}
     G90


##################
[gcode_macro M600]
##################

gcode:
 	JOBCENTER NEWJOB=600


############################
[gcode_macro LOW_TEMP_CHECK]
############################

gcode:
     {% if not params.OVERRIDE is defined %}

          {% if params.T is defined %}

               {% set TMP=params.T|int%}

               {% if printer.configfile.config.extruder.max_temp is defined %}

                    {% if params.T|int>printer.configfile.config.extruder.max_temp|int %}

                         {% set TMP=printer["gcode_macro m600cfg"].default_temp|int %}

                    {% endif %}

               {% endif %}

               {% if TMP|int==0 %}

               {% set TMP=printer["gcode_macro m600cfg"].default_temp|int %}

          {% endif %}

     {% else %}

          {% set TMP=printer["gcode_macro m600cfg"].default_temp|int %}

          {% if printer["gcode_macro JOBCENTER"].temperature|int > 0 %}

               {% set TMP=printer["gcode_macro JOBCENTER"].temperature %}

          {% endif %}

     {% endif %}

     {% if printer.configfile.config.extruder.min_extrude_temp is defined %}

          {% if TMP|int<printer.configfile.config.extruder.min_extrude_temp|int %}

               {% set TMP=printer["gcode_macro m600cfg"].default_temp %}

          {% endif%}

     {% endif %}

     {% else %}

          {% if params.T is defined %}

               {% set TMP=params.T|int %}

          {% else %}

               {% set TMP=printer["gcode_macro m600cfg"].default_temp %}

          {% endif %}

     {% endif %}

     {% if printer.extruder.temperature|int > TMP|int %}

               M{printer["gcode_macro m600cfg"].output|int} Temperature set to {TMP}.
               M104 S{TMP}

          {% else %}

               M{printer["gcode_macro m600cfg"].output|int} Heating to {TMP}
               M109 S{TMP}

     {% endif %}

##### THAT'S IT !