List of parts to print for Voron 2.4 organized by the Assembly Manuals (version 2022-07-04) and the LDO Build Notes order of assembly, allowing for just-in-time printing of parts while building the printer. Configuration is standard Voron 2.4 + the additional parts from the LDO kit (Stealthburner + Clockwork 1, DIN rail mounts) with choices for E3D, Dragon or Mosquito hot ends on a 250mm, 300mm or 350mm frame.
Names of the sections (such as Gantry/X_Axis/XY Joints) match the name of the STL directory that contains the prints. Note that Voron Design uses filenames starting with [a]_ at the start of a filename to indicate parts that can be printed in an accent color. [c]_ should be printed transparent, [o]_ should be opaque. _x# at the end of a file name indicates that you must print that part more than once (e.g. _x2 = print two times). Similarly the number of checkboxes ([ ]) in front of a filename allow you to check off the already printed parts if you print out this Gist on paper.
STLs for LDO specific parts are marked (LDO) and descriptions can be found on their docs page.
Credit to krobertson for making a Gist of all parts. This Gist is a modified version of that list, organized by order of assembly, removed parts that don't need printing, identified parts that are optional or specific to a build, and fixed a few incorrect part listings.
[ ] [ ] MGN9_rail_guide_x2.stl
[ ] [ ] [ ] [ ] z_rail_stop_x4.stl
[ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] deck_support_4mm_x8.stl
[ ] pulley_jig.stl
[ ] [ ] [a]_belt_tensioner_a_x2.stl
[ ] [ ] [a]_belt_tensioner_b_x2.stl
[ ] [ ] [a]_z_drive_baseplate_a_x2.stl
[ ] [ ] [a]_z_drive_baseplate_b_x2.stl
[ ] [ ] z_drive_main_a_x2.stl
[ ] [ ] z_drive_main_b_x2.stl
[ ] [ ] z_drive_retainer_a_x2.stl
[ ] [ ] z_drive_retainer_b_x2.stl
[ ] [ ] z_motor_mount_a_x2.stl
[ ] [ ] z_motor_mount_b_x2.stl
[ ] [ ] [ ] [ ] [a]_z_tensioner_x4_9mm.stl
[ ] [ ] z_tensioner_bracket_a_x2.stl
[ ] [ ] z_tensioner_bracket_b_x2.stl
[ ] [a]_tensioner_left.stl
[ ] [a]_tensioner_right.stl
[ ] front_idler_left_lower.stl
[ ] front_idler_left_upper.stl
[ ] front_idler_right_lower.stl
[ ] front_idler_right_upper.stl
[ ] a_drive_frame_lower.stl
[ ] a_drive_frame_upper.stl
[ ] b_drive_frame_lower.stl
[ ] b_drive_frame_upper.stl
[ ] [ ] MGN12_rail_guide_x2.stl
[ ] [a]_xy_joint_cable_bridge_2hole.stl
[ ] xy_joint_left_lower.stl
[ ] xy_joint_left_upper.stl
[ ] xy_joint_right_lower.stl
[ ] xy_joint_right_upper.stl
[ ] [ ] [ ] [ ] [a]_z_belt_clip_upper_x4.stl
[ ] [ ] [ ] [ ] [a]_z_belt_clip_lower_x4.stl
[ ] [ ] [ ] [ ] z_joint_lower_x4.stl
[ ] [ ] [ ] [ ] z_joint_upper_x4.stl
for Clockwork 1 extruder
[ ] probe_retainer_bracket.stl <-- for Omron inductive probe
[ ] x_carriage_frame_left_MGN12.stl
[ ] x_carriage_frame_right_MGN12.stl
for Clockwork 2 extruder, assembly on Stealthburner manual page 58
[ ] probe_bracket.stl <-- for Omron inductive probe
[ ] x_frame_V2TR_MGN12_left.stl
[ ] x_frame_V2TR_MGN12_right.stl
[ ] [a]_guidler.stl
[ ] [a]_latch.stl
[ ] [a]_latch_shuttle.stl
[ ] chain_anchor_2hole.stl
[ ] extruder_body.stl
[ ] extruder_motor_plate_for_pcb.stl
[ ] pcb_spacer.stl
[ ] printed_washer.stl <-- use this when mounting the LDO Toolhead PCB to the extruder (manual page 174)
Cover for the LDO Toolhead PCB.
[ ] Pcb_Cover_Clip-On_Mount_cw1.stl
[ ] Pcb_Cover_cw1.stl
Below are the files needed to mount the E3D Revo hotend, there are similiarly named files for other hotends available.
[ ] stealthburner_printhead_revo_voron_front.stl
[ ] stealthburner_printhead_revo_voron_rear_cw1.stl vvv only print one, matching your extruder
[ ] stealthburner_printhead_revo_voron_rear_cw2.stl ^^^
[ ] sb_adxl_mount_ldo_15mm_c_c.stl
[ ] [ ] sb_adxl_washer_x2.stl
[ ] [a]_stealthburner_main_body.stl
[ ] [c]_stealthburner_LED_diffuser.stl
[ ] [o]_stealthburner_LED_carrier.stl
[ ] [o]_stealthburner_LED_diffuser_mask.stl
[ ] SB_5015_Cutting_Tool_A.stl vvv optional, jig for removing the mounting ears of the part cooling fan
[ ] SB_5015_Cutting_Tool_B.stl ^^^
The wiring for the LDO kit differs from the default, consult the LDO Wiring Guide in addition to the Voron 2.4 manual.
These parts are for the display. It is way easier to install it at this point before installing the cable ducts. The assembly and installation of the LCD are covered on page 241, 244-246, 248 and 250 of the manual.
[ ] [a]_btt_knob_light_shield.stl
[ ] [a]_mini12864_case_front_insert.stl
[ ] [a]_mini12864_case_hinge.stl
[ ] mini12864_case_front.stl
[ ] mini12864_case_rear.stl
[ ] beefy_raspberry_bracket.stl <-- needs 1 additional DIN rail mount
[ ] nozzle_probe_ldo.stl
[ ] toolhead_breakout_pcb_bracket.stl <-- needs 1 additional DIN rail mount
[ ] [a]_endstop_pod_D2F_switch.stl
[ ] [ ] [ ] [ ] [ ] pcb_din_clip_x3.stl <-- print 2 more for the Raspberry Pi and the Toolhead Breakout PCB
[ ] [ ] lrs_200_psu_bracket_x2.stl
[ ] Octopus_bracket_set.stl
The manual covers prep and installation of these two skirts later (page 184, 195, 242/43, 252/53) but it is advisable to install them at this point so you can complete the electronics installation on the bottom of the printer.
[ ] power_inlet_IECGS_1.2mm.stl
[ ] keystone_panel.stl
The LED light strips included in the LDO kit can be mounted using these bar clips by eddie. In total, you will need 36 or 42 clips for the 300mm and 350mm frame respectively.
LED_Bar_Clip_Misumi_version2.stl
[ ] [a]_belt_guard_a_x2.stl
[ ] [a]_belt_guard_b_x2.stl
[ ] [ ] [a]_fan_grill_a_x2.stl
[ ] [ ] [a]_fan_grill_b_x2.stl
[ ] [ ] [a]_fan_grill_retainer_x2.stl
[ ] [a]_keystone_blank_insert.stl
[ ] [ ] side_fan_support_x2.stl
Use these skirts when printing a 250mm frame.
[ ] front_skirt_a_250.stl
[ ] front_skirt_b_250.stl
[ ] rear_center_skirt_250.stl
[ ] [ ] side_skirt_a_250_x2.stl
[ ] [ ] side_skirt_b_250_x2.stl
Use these skirts when printing a 300mm frame.
[ ] front_skirt_a_300.stl
[ ] front_skirt_b_300.stl
[ ] rear_center_skirt_300.stl
[ ] [ ] side_skirt_a_300_x2.stl
[ ] [ ] side_skirt_b_300_x2.stl
Use these skirts when printing a 350mm frame.
[ ] front_skirt_a_350.stl
[ ] front_skirt_b_350.stl
[ ] rear_center_skirt_350.stl
[ ] [ ] side_skirt_a_350_x2.stl
[ ] [ ] side_skirt_b_350_x2.stl
[ ] [ ] [ ] [ ] bottom_panel_clip_x4.stl
[ ] [ ] bottom_panel_hinge_x2.stl
[ ] z_belt_cover_a_x2.stl <-- print only one + the LDO version below
[ ] [ ] z_belt_cover_b_x2.stl
[ ] z_belt_cover_a_led.stl
[ ] [ ] [ ] [ ] door_hinge_x4.stl
[ ] [ ] handle_a_x2.stl
[ ] [ ] handle_b_x2.stl
[ ] [ ] latch_x2.stl
[ ] [ ] [ ] [ ] bottom_panel_clip_x4.stl
[ ] [ ] bottom_panel_hinge_x2.stl
[ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] corner_panel_clip_3mm_x12.stl <-- 3mm no foam, 6mm w/foam
[ ] [ ] [ ] [ ] corner_panel_clip_6mm_x4.stl <-- print either the 3mm or
[ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] midspan_panel_clip_3mm_x12.stl <-- the 6mm set
[ ] [ ] [ ] midspan_panel_clip_6mm_x3.stl <--
[ ] [ ] z_belt_cover_a_x2.stl
[ ] [ ] z_belt_cover_b_x2.stl
[ ] bowen_retainer.stl
[ ] spool_holder.stl
[ ] [a]_filter_access_cover.stl
[ ] [ ] [a]_exhaust_filter_mount_x2.stl
[ ] exhaust_filter_grill.stl
[ ] exhaust_filter_housing.stl