ABS Config for Ender 5 w/ PEX bed

Config.ini

# generated by SuperSlicer 2.3.57 on 2022-02-09 at 23:15:44 UTC
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_custom_model = 
bed_custom_texture = 
bed_shape = 5x2.5,240x2.5,240x237.5,5x237.5
bed_temperature = 110
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;{layer_z}\n\n
between_objects_gcode = 
bottom_fill_pattern = rectilinear
bottom_solid_layers = 5
bottom_solid_min_thickness = 0
bridge_acceleration = 250
bridge_angle = 0
bridge_fan_speed = 30
bridge_flow_ratio = 0.94999999999999996
bridge_speed = 30
brim_width = 0
clip_multipart_objects = 1
color_change_gcode = M600
colorprint_heights = 
compatible_printers_condition_cummulative = printer_model=~/(ENDER|CR|SERMOON).*/;printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
complete_objects = 0
cooling = 1
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_acceleration = 500
default_filament_profile = "Creality PLA @CREALITY"
default_print_profile = 0.20mm NORMAL @CREALITY
deretract_speed = 20
disable_fan_first_layers = 3
dont_support_bridges = 1
draft_shield = 0
duplicate_distance = 6
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = END_PRINT
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 100%
external_perimeter_speed = 22
external_perimeters_first = 0
extra_loading_move = -2
extra_perimeters = 0
extruder_clearance_height = 34
extruder_clearance_radius = 47
extruder_colour = #FCE94F
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.14
extrusion_width = 111%
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #DDDDDD
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 20
filament_custom_variables = ""
filament_density = 1.04
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 11
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 5.5
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = nil
filament_settings_id = "MatterHackers ABS @ Benny"
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = nil
filament_wipe_extra_perimeter = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
fill_angle = 45
fill_density = 40%
fill_pattern = grid
first_layer_acceleration = 0
first_layer_bed_temperature = 110
first_layer_extrusion_width = 100%
first_layer_height = 0.2
elefant_foot_compensation = 0.1
first_layer_speed = 12
first_layer_temperature = 245
full_fan_speed_layer = 4
gap_fill_last = 0
gap_fill_speed = 30
gcode_comments = 0
gcode_flavor = reprap
gcode_label_objects = 1
gcode_precision_e = 5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 0
infill_connection_bottom = connected
infill_connection_solid = connected
infill_connection_top = connected
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 100%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 50
inherits_cummulative = "0.20mm NORMAL @CREALITY";"Generic ABS @CREALITY";"Creality Ender-5 0.4mm"
interface_shells = 0
ironing = 0
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
layer_height = 0.2
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 1000
machine_max_acceleration_extruding = 500
machine_max_acceleration_retracting = 1000
machine_max_acceleration_x = 500
machine_max_acceleration_y = 500
machine_max_acceleration_z = 100
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 5
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_fan_speed = 0
max_gcode_per_second = 1500
max_layer_height = 0.32
max_print_height = 300
max_print_speed = 100
max_volumetric_speed = 0
min_fan_speed = 0
min_layer_height = 0.04
min_print_speed = 15
min_skirt_length = 4
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{print_time}_{layer_height}mm_{temperature[0]}C_{filament_type[0]}_{printer_model}.gcode
overhangs = 1
parking_pos_retraction = 92
pause_print_gcode = 
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 100%
perimeter_speed = 36
perimeters = 4
physical_printer_settings_id = 
post_process = 
print_custom_variables = 
print_settings_id = Voron ABS @ Benny
printer_custom_variables = 
printer_model = ENDER5
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER5\nPRINTER_HAS_BOWDEN
printer_settings_id = Benny 0.4mm - Klipper
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_port = 
raft_layers = 0
remaining_times = 0
remaining_times_type = m73
resolution = 0.0125
resolution_internal = 0.2
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 4
retract_length_toolchange = 1
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
seam_position = nearest
silent_mode = 0
single_extruder_multi_material = 0
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 1
slice_closing_radius = 0.049
slowdown_below_layer_time = 20
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 100%
solid_infill_speed = 40
solid_over_perimeters = 2
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n"
start_gcode = START_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} BED_TEMP=[first_layer_bed_temperature]
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.35000000000000003
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 95%
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 40
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 60%
temperature = 245
template_custom_gcode = 
thin_walls = 1
threads = 12
thumbnails = 0x0,0x0
toolchange_gcode = 
top_fill_pattern = monotonic
top_infill_extrusion_width = 100%
top_solid_infill_speed = 30
top_solid_layers = 5
top_solid_min_thickness = 0
travel_speed = 150
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
wipe_into_infill = 0
wipe_into_objects = 0
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 160
wipe_tower_y = 160
wiping_volumes_extruders = 70,70
wiping_volumes_matrix = 0
xy_size_compensation = 0
z_offset = 0