Example of how to setup Klipper to use the gocode_shell_command to do timelapse (pre mainsail built in timelapse)

Snapshots.cfg

# Requires `gcode_shell_command` extension to Moonraker (installing via KIUAH is the easy way)
# Requires gphoto2 http://www.gphoto.org/

[gcode_shell_command gphoto2_trigger_snapshot]
command: gphoto2 --auto-detect --trigger-capture
timeout: 10. ; make sure this is long enough to account for focus time
verbose: True

[gcode_shell_command gphoto2_init_camera]
command: gphoto2 --auto-detect --set-config capturetarget=1
timeout: 2.
verbose: True

#Invoke this in your start print script
[gcode_macro INIT_CAMERA]
gcode:
  {% if printer.save_variables.variables.snapshots_enabled %}
    RUN_SHELL_COMMAND CMD=gphoto2_init_camera
  {% else %}
    { action_respond_info("Snapshots disabled") }
  {% endif %}

# Invoke this after each layer
[gcode_macro TAKE_SNAPSHOT]
description: Saves current location, moves toolhead to rear of bed, and takes a snapshot before returning.
gcode:
  {% if printer.save_variables.variables.snapshots_enabled %}
    {% set delayMS = 2000 %} ; Delay after moving and before taking the snapshot, so we don't get the print head in motion
    {% set snapshotPositionX = printer.toolhead.axis_maximum.x / 2 %}
    {% set snapshotPositionY = printer.toolhead.axis_maximum.y - 5 %}
    {% set currentX = printer.gcode_move.gcode_position.x %}
    {% set currentY = printer.gcode_move.gcode_position.y %}
    {% set currentZ = printer.gcode_move.gcode_position.z %} ; could be used for z-hop which we are not doing in this macro, so it's best to run this in AFTER_LAYER_CHANGE
    SAVE_GCODE_STATE NAME=take_snapshot_state
  
    {% if printer.extruder.can_extrude|lower == 'true' %}
      G10 ; retract
    {% endif %}
  
    G90
  
    G0 X{snapshotPositionX} Y{snapshotPositionY} F5000.0 ;Move to snapshot position
  
    G4 P{delayMS} ; Dwell for delayMS seconds
  
    RUN_SHELL_COMMAND CMD=gphoto2_trigger_snapshot
  
    G0 X{currentX} Y{currentY} F5000.0 ;Return to original position
  
    {% if printer.extruder.can_extrude|lower == 'true' %}
      G11 ; unretract
    {% endif %}
  
    RESTORE_GCODE_STATE NAME=take_snapshot_state
  {% else %}
    { action_respond_info("Snapshots are DISABLED. Run ENABLE_SNAPSHOTS or TOGGLE_SNAPSHOTS to ENABLE.") }
  {% endif %}

[gcode_macro ENABLE_SNAPSHOTS]
gcode:
  SAVE_VARIABLE VARIABLE=snapshots_enabled VALUE=True
  INIT_CAMERA
  { action_respond_info("Snapshots enabled") }

[gcode_macro DISABLE_SNAPSHOTS]
gcode:
  SAVE_VARIABLE VARIABLE=snapshots_enabled VALUE=False
  { action_respond_info("Snapshots disabled") }

[gcode_macro TOGGLE_SNAPSHOTS]
gcode:
  {% if printer.save_variables.variables.snapshots_enabled %}
    DISABLE_SNAPSHOTS
  {% else %}
    ENABLE_SNAPSHOTS
  {% endif %}

[gcode_macro QUERY_SNAP_SHOTS]
gcode:
  {% if printer.save_variables.variables.snapshots_enabled %}
    { action_respond_info("Snapshots enabled") }
  {% else %}
    { action_respond_info("Snapshots disabled") }
  {% endif %}

hello I would also like to connect my dslr camera to clipper I just got clipper how can I get started I already have gphoto2 installed.