config.ini

# generated by Slic3r 0.9.9-dev on Mon Feb  4 09:57:15 2013
avoid_crossing_perimeters = 1
bed_size = 180,180
bed_temperature = 0
bottom_solid_layers = 3
bridge_fan_speed = 100
bridge_flow_ratio = 0.6
bridge_speed = 20
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M117 Print Done\nM104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nG4 5 ; wait 5 seconds\nM81 ; ps off
external_perimeter_speed = 100%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.0
extrusion_width = 0.66
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 2.85
fill_angle = 35
fill_density = 0.33
fill_pattern = rectilinear
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 80%
first_layer_temperature = 185
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.66
infill_speed = 25
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
min_skirt_length = 0
notes = black-pla
nozzle_diameter = 0.5
only_retract_when_crossing_perimeters = 
output_filename_format = [input_filename_base]_[filament_preset]_3r.gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.66
perimeter_speed = 20
perimeters = 3
post_process = 
print_center = 90,90
raft_layers = 0
randomize_start = 
retract_before_travel = 3
retract_length = 1.0
retract_length_toolchange = 0
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 10
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 15
small_perimeter_speed = 20
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_speed = 25
start_gcode = M80 ; ps on
support_material = 0
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0.66
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 25
support_material_threshold = 45
temperature = 185
threads = 2
toolchange_gcode = 
top_solid_infill_speed = 25
top_solid_layers = 3
travel_speed = 25
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0