A simple modbus rtu slave device that works with Arduino Uno. For testing purposes.

MobusRTUSlaveExample.ino

/*
Before you begin, make sure that you have the correct libraries installed.
You must install Modbus Library given here: https://code.google.com/archive/p/arduino-modbus-slave/downloads
This is just an example taken from that library. I have written no part of this code. All credit goes to the original authors.

- xandfury
*/
#include <modbus.h>
#include <modbusDevice.h>
#include <modbusRegBank.h>
#include <modbusSlave.h>

/*
This example code shows a quick and dirty way to get an
arduino to talk to a modbus master device with a
device ID of 1 at 9600 baud.
*/

//Setup the brewtrollers register bank
//All of the data accumulated will be stored here
modbusDevice regBank;
//Create the modbus slave protocol handler
modbusSlave slave;

void setup()
{   

//Assign the modbus device ID.  
  regBank.setId(1);

/*
modbus registers follow the following format
00001-09999  Digital Outputs, A master device can read and write to these registers
10001-19999  Digital Inputs, A master device can only read the values from these registers
30001-39999  Analog Inputs, A master device can only read the values from these registers
40001-49999  Analog Outputs, A master device can read and write to these registers 

Analog values are 16 bit unsigned words stored with a range of 0-32767
Digital values are stored as bytes, a zero value is OFF and any nonzer value is ON

It is best to configure registers of like type into contiguous blocks.  this
allows for more efficient register lookup and and reduces the number of messages
required by the master to retrieve the data
*/

//Add Digital Output registers 00001-00016 to the register bank
  regBank.add(1);
  regBank.add(2);
  regBank.add(3);
  regBank.add(4);
  regBank.add(5);
  regBank.add(6);
  regBank.add(7);
  regBank.add(8);
  regBank.add(9);
  regBank.add(10);
  regBank.add(11);
  regBank.add(12);
  regBank.add(13);
  regBank.add(14);
  regBank.add(15);
  regBank.add(16);

//Add Digital Input registers 10001-10008 to the register bank
  regBank.add(10001);  
  regBank.add(10002);  
  regBank.add(10003);  
  regBank.add(10004);  
  regBank.add(10005);  
  regBank.add(10006);  
  regBank.add(10007);  
  regBank.add(10008);  

//Add Analog Input registers 30001-10010 to the register bank
  regBank.add(30001);  
  regBank.add(30002);  
  regBank.add(30003);  
  regBank.add(30004);  
  regBank.add(30005);  
  regBank.add(30006);  
  regBank.add(30007);  
  regBank.add(30008);  
  regBank.add(30009);  
  regBank.add(30010);  

//Add Analog Output registers 40001-40020 to the register bank
  regBank.add(40001);  
  regBank.add(40002);  
  regBank.add(40003);  
  regBank.add(40004);  
  regBank.add(40005);  
  regBank.add(40006);  
  regBank.add(40007);  
  regBank.add(40008);  
  regBank.add(40009);  
  regBank.add(40010);  
  regBank.add(40011);  
  regBank.add(40012);  
  regBank.add(40013);  
  regBank.add(40014);  
  regBank.add(40015);  
  regBank.add(40016);  
  regBank.add(40017);  
  regBank.add(40018);  
  regBank.add(40019);  
  regBank.add(40020);  

/*
Assign the modbus device object to the protocol handler
This is where the protocol handler will look to read and write
register data.  Currently, a modbus slave protocol handler may
only have one device assigned to it.
*/
  slave._device = &regBank;  

// Initialize the serial port for coms at 9600 baud  
  slave.setBaud(9600);   
}

void loop()
{
//put some data into the registers
  regBank.set(1, 1);  
  regBank.set(2, 1);  
  regBank.set(3, 0);  
  regBank.set(4, 1);  
  regBank.set(5, 1);  
  regBank.set(6, 0);  
  regBank.set(7, 1);  
  regBank.set(8, 0);  

  regBank.set(10001, 1);
  regBank.set(10002, 1);  
  regBank.set(10003, 1);  
  regBank.set(10004, 1);  
  regBank.set(10005, 0);  
  regBank.set(10006, 0);  
  regBank.set(10007, 0);  
  regBank.set(10008, 0);  


  regBank.set(30001,1);
  regBank.set(30002,2);
  regBank.set(30003,3);
  regBank.set(30004,4);
  regBank.set(30005,5);
  regBank.set(30006,6);
  regBank.set(30007,7);
  regBank.set(30008,8);
  regBank.set(30009,9);
  regBank.set(30010,10);

  regBank.set(40001,1);
  regBank.set(40002,2);
  regBank.set(40003,2);
  regBank.set(40004,4);
  regBank.set(40005,5);
  regBank.set(40006,6);
  regBank.set(40007,7);
  regBank.set(40008,8);
  regBank.set(40009,9);
  regBank.set(40010,10);
  
 while(1)
  {
    //put a random number into registers 1, 10001, 30001 and 40001
    regBank.set(1, (byte) random(0, 2));
    regBank.set(10001, (byte) random(0, 2));
    regBank.set(30001, (word) random(0, 32767));
    regBank.set(40001, (word) random(0, 32767));
    
     slave.run();  
  }
}

i am beginner in modbus , how we write analog value on PLC as master

please share schematic regarding this Code , RS 485 module connection to arduino ?
[email protected] i want send 16 keys push to on data from arduino (as slave) to PLC/ Simply nodebus Software (as MASTER) and want receive error msg to arduino LCD 20x4 , please help

Hi.
When calling 300001 and 400001 the information is swapped around? Anybody sitting with the same problem?

hi , how to Add Digital Input registers more than 8 (100001-19999 )??
just trying with 20 digital input on mega2560, not work !! only 8 digital input can get data, after adress 100008 ,slave only gave data zero.

Dear, I need to know how to do so that with this library I can send modbus float. Thank you best regards

one simple way that works in every case is:

struct modbusLongReg{
uint16_t lsw;
uint16_t msw;
}* mbSplit;

double f = 0.3;

mbSplit = &f;

regBank.set(40001,mbSplit->lsw);
regBank.set(40002,mbSplit->msw);

you can configure word order as you need on the other side.

can you plz share the connections

hi sir, sorry to say but after spending 2 months on this project i dropped it , there are lots of mismatched hardware and software issuse.

…

On Tue, 3 Aug 2021 at 10:51, eklavyainfo ***@***.***> wrote: ***@***.**** commented on this gist. ------------------------------ can you plz share the connections — You are receiving this because you commented. Reply to this email directly, view it on GitHub <https://gist.github.com/626e7849422e8757e8fa1c16403e22ee#gistcomment-3841432>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN4GKIB2LGV4CS4S5EIJB3LT254FLANCNFSM4JRYU2OA> . Triage notifications on the go with GitHub Mobile for iOS <https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675> or Android <https://play.google.com/store/apps/details?id=com.github.android&utm_campaign=notification-email> .

-- Thanks & Regards, AIMSTEC * |* Mr. Ameeth Sutarr | Mobile - 9920465768 | 8850223488 Email ID : ***@***.*** ***@***.***> |

What's UP Man.
About serial config (slave.setBaud),
How Can I change to 8N2?
And Can I use Serial2 to modbus conection?

Thanks