Skip to content

Instantly share code, notes, and snippets.

@xerpi

xerpi/camera.dtsi

Last active September 12, 2022 10:08
Show Gist options
  • Save xerpi/8d89caa1b850ad4bb2404e6e0f7f018f to your computer and use it in GitHub Desktop.
Save xerpi/8d89caa1b850ad4bb2404e6e0f7f018f to your computer and use it in GitHub Desktop.
Download ZIP
Ultra96v2 with Raspberry Pi Camera v2.1 (IMX219 sensor)
Raw
camera.dtsi
/ {
cam_clk: cam_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
};
&i2csw_2 {
imx219@10 {
compatible = "sony,imx219";
reg = <0x10>;
clocks = <&cam_clk>;
clock-names = "xclk";
//reset-gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
status = "okay";
port {
imx219_to_mipi_csi2_rx_0: endpoint {
remote-endpoint = <&mipi_csi_invideo_pipeline_mipi_csi2_rx_subsyst_0>;
link-frequencies = /bits/ 64 <456000000>;
clock-noncontinuous;
clock-lanes = <0>;
data-lanes = <1 2>;
};
};
};
};
Raw
gen_dts
xsct
hsi open_hw_design design_1_wrapper.xsa
hsi set_repo_path /path/to/device-tree-xlnx
hsi create_sw_design device-tree -os device_tree -proc psu_cortexa53_0
hsi generate_target -dir my_dts
exit
Raw
pl.dtsi
/*
* CAUTION: This file is automatically generated by Xilinx.
* Version: XSCT 2022.1
* Today is: Tue Aug 23 20:26:12 2022
*/
#include <dt-bindings/media/xilinx-vip.h>
/ {
amba_pl: amba_pl@0 {
#address-cells = <2>;
#size-cells = <2>;
compatible = "simple-bus";
ranges ;
axi_intc_0: interrupt-controller@a0020000 {
#interrupt-cells = <2>;
clock-names = "s_axi_aclk";
clocks = <&misc_clk_0>;
compatible = "xlnx,axi-intc-4.1", "xlnx,xps-intc-1.00.a";
interrupt-controller ;
interrupt-names = "irq";
interrupt-parent = <&gic>;
interrupts = <0 89 4>;
reg = <0x0 0xa0020000 0x0 0x10000>;
xlnx,kind-of-intr = <0x0>;
xlnx,num-intr-inputs = <0x2>;
};
misc_clk_0: misc_clk_0 {
#clock-cells = <0>;
clock-frequency = <150000000>;
compatible = "fixed-clock";
};
video_pipeline_mipi_csi2_rx_subsyst_0: mipi_csi2_rx_subsystem@a0000000 {
clock-names = "lite_aclk", "dphy_clk_200M", "video_aclk";
clocks = <&misc_clk_0>, <&misc_clk_1>, <&misc_clk_0>;
compatible = "xlnx,mipi-csi2-rx-subsystem-5.1", "xlnx,mipi-csi2-rx-subsystem-5.0";
interrupt-names = "csirxss_csi_irq";
interrupt-parent = <&axi_intc_0>;
interrupts = <0 2>;
reg = <0x0 0xa0000000 0x0 0x2000>;
xlnx,axis-tdata-width = <32>;
xlnx,csi-pxl-format = <0x2b>;
xlnx,dphy-present ;
xlnx,max-lanes = <2>;
xlnx,ppc = <1>;
xlnx,vc = <4>;
xlnx,vfb ;
mipi_csi_portsvideo_pipeline_mipi_csi2_rx_subsyst_0: ports {
#address-cells = <1>;
#size-cells = <0>;
mipi_csi_port1video_pipeline_mipi_csi2_rx_subsyst_0: port@1 {
/* Fill cfa-pattern=rggb for raw data types, other fields video-format and video-width user needs to fill */
reg = <1>;
xlnx,cfa-pattern = "rggb";
xlnx,video-format = <XVIP_VF_MONO_SENSOR>;
xlnx,video-width = <8>;
mipi_csirx_outvideo_pipeline_mipi_csi2_rx_subsyst_0: endpoint {
remote-endpoint = <&video_pipeline_v_demosaic_0video_pipeline_mipi_csi2_rx_subsyst_0>;
};
};
mipi_csi_port0video_pipeline_mipi_csi2_rx_subsyst_0: port@0 {
/* Fill cfa-pattern=rggb for raw data types, other fields video-format,video-width user needs to fill */
/* User need to add something like remote-endpoint=<&out> under the node csiss_in:endpoint */
reg = <0>;
xlnx,cfa-pattern = "rggb";
xlnx,video-format = <XVIP_VF_MONO_SENSOR>;
xlnx,video-width = <8>;
mipi_csi_invideo_pipeline_mipi_csi2_rx_subsyst_0: endpoint {
remote-endpoint = <&imx219_to_mipi_csi2_rx_0>;
data-lanes = <1 2>;
};
};
};
};
misc_clk_1: misc_clk_1 {
#clock-cells = <0>;
clock-frequency = <200000000>;
compatible = "fixed-clock";
};
video_pipeline_v_demosaic_0: v_demosaic@a0030000 {
clock-names = "ap_clk";
clocks = <&misc_clk_0>;
compatible = "xlnx,v-demosaic-1.1", "xlnx,v-demosaic";
reg = <0x0 0xa0030000 0x0 0x10000>;
reset-gpios = <&gpio 85 1>;
xlnx,max-height = <1080>;
xlnx,max-width = <1920>;
xlnx,s-axi-ctrl-addr-width = <0x6>;
xlnx,s-axi-ctrl-data-width = <0x20>;
demosaic_portsvideo_pipeline_v_demosaic_0: ports {
#address-cells = <1>;
#size-cells = <0>;
demosaic_port1video_pipeline_v_demosaic_0: port@1 {
/* For cfa-pattern=rggb user needs to fill as per BAYER format */
reg = <1>;
xlnx,cfa-pattern = "rggb";
xlnx,video-width = <8>;
demo_outvideo_pipeline_v_demosaic_0: endpoint {
remote-endpoint = <&video_pipeline_v_gamma_lut_0video_pipeline_v_demosaic_0>;
};
};
demosaic_port0video_pipeline_v_demosaic_0: port@0 {
/* For cfa-pattern=rggb user needs to fill as per BAYER format */
reg = <0>;
xlnx,cfa-pattern = "rggb";
xlnx,video-width = <8>;
video_pipeline_v_demosaic_0video_pipeline_mipi_csi2_rx_subsyst_0: endpoint {
remote-endpoint = <&mipi_csirx_outvideo_pipeline_mipi_csi2_rx_subsyst_0>;
};
};
};
};
video_pipeline_v_frmbuf_wr_0: v_frmbuf_wr@a0080000 {
#dma-cells = <1>;
clock-names = "ap_clk";
clocks = <&misc_clk_0>;
compatible = "xlnx,v-frmbuf-wr-2.4", "xlnx,axi-frmbuf-wr-v2.2";
interrupt-names = "interrupt";
interrupt-parent = <&axi_intc_0>;
interrupts = <1 2>;
reg = <0x0 0xa0080000 0x0 0x10000>;
reset-gpios = <&gpio 89 1>;
xlnx,dma-addr-width = <64>;
xlnx,dma-align = <8>;
xlnx,max-height = <1080>;
xlnx,max-width = <1920>;
xlnx,pixels-per-clock = <1>;
xlnx,s-axi-ctrl-addr-width = <0x7>;
xlnx,s-axi-ctrl-data-width = <0x20>;
xlnx,vid-formats = "uyvy", "y8", "yuyv";
xlnx,video-width = <8>;
};
video_pipeline_v_gamma_lut_0: v_gamma_lut@a0090000 {
clock-names = "ap_clk";
clocks = <&misc_clk_0>;
compatible = "xlnx,v-gamma-lut-1.1", "xlnx,v-gamma-lut";
reg = <0x0 0xa0090000 0x0 0x10000>;
reset-gpios = <&gpio 86 1>;
xlnx,max-height = <1080>;
xlnx,max-width = <1920>;
xlnx,s-axi-ctrl-addr-width = <13>;
xlnx,s-axi-ctrl-data-width = <32>;
gamma_portsvideo_pipeline_v_gamma_lut_0: ports {
#address-cells = <1>;
#size-cells = <0>;
gamma_port1video_pipeline_v_gamma_lut_0: port@1 {
reg = <1>;
xlnx,video-width = <8>;
gamma_outvideo_pipeline_v_gamma_lut_0: endpoint {
remote-endpoint = <&video_pipeline_v_proc_ss_cscvideo_pipeline_v_gamma_lut_0>;
};
};
gamma_port0video_pipeline_v_gamma_lut_0: port@0 {
reg = <0>;
xlnx,video-width = <8>;
video_pipeline_v_gamma_lut_0video_pipeline_v_demosaic_0: endpoint {
remote-endpoint = <&demo_outvideo_pipeline_v_demosaic_0>;
};
};
};
};
video_pipeline_v_proc_ss_csc: v_proc_ss@a0010000 {
clock-names = "aclk";
clocks = <&misc_clk_0>;
compatible = "xlnx,v-proc-ss-2.3", "xlnx,vpss-csc", "xlnx,v-vpss-csc";
reg = <0x0 0xa0010000 0x0 0x10000>;
reset-gpios = <&gpio 87 1>;
xlnx,colorspace-support = <0>;
xlnx,csc-enable-window = "true";
xlnx,max-height = <1080>;
xlnx,max-width = <1920>;
xlnx,num-video-components = <3>;
xlnx,samples-per-clk = <1>;
xlnx,topology = <3>;
xlnx,use-uram = <0>;
xlnx,video-width = <8>;
csc_portsvideo_pipeline_v_proc_ss_csc: ports {
#address-cells = <1>;
#size-cells = <0>;
csc_port1video_pipeline_v_proc_ss_csc: port@1 {
/* For xlnx,video-format user needs to fill as per their requirement */
reg = <1>;
xlnx,video-format = <XVIP_VF_YUV_420>;
xlnx,video-width = <8>;
csc_outvideo_pipeline_v_proc_ss_csc: endpoint {
remote-endpoint = <&video_pipeline_v_proc_ss_scalervideo_pipeline_v_proc_ss_csc>;
};
};
csc_port0video_pipeline_v_proc_ss_csc: port@0 {
/* For xlnx,video-format user needs to fill as per their requirement */
reg = <0>;
xlnx,video-format = <XVIP_VF_YUV_420>;
xlnx,video-width = <8>;
video_pipeline_v_proc_ss_cscvideo_pipeline_v_gamma_lut_0: endpoint {
remote-endpoint = <&gamma_outvideo_pipeline_v_gamma_lut_0>;
};
};
};
};
video_pipeline_v_proc_ss_scaler: v_proc_ss@a0040000 {
clock-names = "aclk_axis", "aclk_ctrl";
clocks = <&misc_clk_0>, <&misc_clk_0>;
compatible = "xlnx,v-proc-ss-2.3", "xlnx,vpss-scaler-2.2", "xlnx,v-vpss-scaler-2.2", "xlnx,vpss-scaler";
reg = <0x0 0xa0040000 0x0 0x40000>;
reset-gpios = <&gpio 88 1>;
xlnx,colorspace-support = <0>;
xlnx,csc-enable-window = "true";
xlnx,enable-csc = "true";
xlnx,h-scaler-phases = <64>;
xlnx,h-scaler-taps = <8>;
xlnx,max-height = <1080>;
xlnx,max-num-phases = <64>;
xlnx,max-width = <1920>;
xlnx,num-hori-taps = <8>;
xlnx,num-vert-taps = <8>;
xlnx,pix-per-clk = <1>;
xlnx,samples-per-clk = <1>;
xlnx,scaler-algorithm = <2>;
xlnx,topology = <0>;
xlnx,use-uram = <0>;
xlnx,v-scaler-phases = <64>;
xlnx,v-scaler-taps = <8>;
xlnx,video-width = <8>;
scaler_portsvideo_pipeline_v_proc_ss_scaler: ports {
#address-cells = <1>;
#size-cells = <0>;
scaler_port1video_pipeline_v_proc_ss_scaler: port@1 {
/* For xlnx,video-format user needs to fill as per their requirement */
reg = <1>;
xlnx,video-format = <XVIP_VF_YUV_420>;
xlnx,video-width = <8>;
sca_outvideo_pipeline_v_proc_ss_scaler: endpoint {
remote-endpoint = <&video_pipeline_v_frmbuf_wr_0video_pipeline_v_proc_ss_scaler>;
};
};
scaler_port0video_pipeline_v_proc_ss_scaler: port@0 {
/* For xlnx,video-format user needs to fill as per their requirement */
reg = <0>;
xlnx,video-format = <XVIP_VF_YUV_420>;
xlnx,video-width = <8>;
video_pipeline_v_proc_ss_scalervideo_pipeline_v_proc_ss_csc: endpoint {
remote-endpoint = <&csc_outvideo_pipeline_v_proc_ss_csc>;
};
};
};
};
vcap_video_pipeline_v_proc_ss_scaler {
compatible = "xlnx,video";
dma-names = "port0";
dmas = <&video_pipeline_v_frmbuf_wr_0 0>;
vcap_portsvideo_pipeline_v_proc_ss_scaler: ports {
#address-cells = <1>;
#size-cells = <0>;
vcap_portvideo_pipeline_v_proc_ss_scaler: port@0 {
direction = "input";
reg = <0>;
video_pipeline_v_frmbuf_wr_0video_pipeline_v_proc_ss_scaler: endpoint {
remote-endpoint = <&sca_outvideo_pipeline_v_proc_ss_scaler>;
};
};
};
};
};
};
Raw
ultra96_v2_design.tcl
#*****************************************************************************************
# Vivado (TM) v2022.1 (64-bit)
#
# ultra96_design.tcl: Tcl script for re-creating project 'ultra96_design'
#
# Generated by Vivado on Tue Aug 09 11:30:01 JST 2022
# IP Build 3524634 on Mon Apr 18 20:55:01 MDT 2022
#
# This file contains the Vivado Tcl commands for re-creating the project to the state*
# when this script was generated. In order to re-create the project, please source this
# file in the Vivado Tcl Shell.
#
# * Note that the runs in the created project will be configured the same way as the
# original project, however they will not be launched automatically. To regenerate the
# run results please launch the synthesis/implementation runs as needed.
#
#*****************************************************************************************
# NOTE: In order to use this script for source control purposes, please make sure that the
# following files are added to the source control system:-
#
# 1. This project restoration tcl script (ultra96_design.tcl) that was generated.
#
# 2. The following source(s) files that were local or imported into the original project.
# (Please see the '$orig_proj_dir' and '$origin_dir' variable setting below at the start of the script)
#
# "/home/xerpi/Desktop/Research/ultra96_design/ultra96_design/ultra96_design.srcs/sources_1/imports/hdl/design_1_wrapper.v"
#
# 3. The following remote source files that were added to the original project:-
#
# <none>
#
#*****************************************************************************************
# Check file required for this script exists
proc checkRequiredFiles { origin_dir} {
set status true
set files [list \
"[file normalize "$origin_dir/Desktop/Research/ultra96_design/ultra96_design/ultra96_design.srcs/sources_1/imports/hdl/design_1_wrapper.v"]"\
]
foreach ifile $files {
if { ![file isfile $ifile] } {
puts " Could not find local file $ifile "
set status false
}
}
set paths [list \
"[file normalize "$origin_dir/[file normalize "$origin_dir/Desktop/Research/ultra96_design/ip"]"]"\
]
foreach ipath $paths {
if { ![file isdirectory $ipath] } {
puts " Could not access $ipath "
set status false
}
}
return $status
}
# Set the reference directory for source file relative paths (by default the value is script directory path)
set origin_dir "."
# Use origin directory path location variable, if specified in the tcl shell
if { [info exists ::origin_dir_loc] } {
set origin_dir $::origin_dir_loc
}
# Set the project name
set _xil_proj_name_ "ultra96_design"
# Use project name variable, if specified in the tcl shell
if { [info exists ::user_project_name] } {
set _xil_proj_name_ $::user_project_name
}
variable script_file
set script_file "ultra96_design.tcl"
# Help information for this script
proc print_help {} {
variable script_file
puts "\nDescription:"
puts "Recreate a Vivado project from this script. The created project will be"
puts "functionally equivalent to the original project for which this script was"
puts "generated. The script contains commands for creating a project, filesets,"
puts "runs, adding/importing sources and setting properties on various objects.\n"
puts "Syntax:"
puts "$script_file"
puts "$script_file -tclargs \[--origin_dir <path>\]"
puts "$script_file -tclargs \[--project_name <name>\]"
puts "$script_file -tclargs \[--help\]\n"
puts "Usage:"
puts "Name Description"
puts "-------------------------------------------------------------------------"
puts "\[--origin_dir <path>\] Determine source file paths wrt this path. Default"
puts " origin_dir path value is \".\", otherwise, the value"
puts " that was set with the \"-paths_relative_to\" switch"
puts " when this script was generated.\n"
puts "\[--project_name <name>\] Create project with the specified name. Default"
puts " name is the name of the project from where this"
puts " script was generated.\n"
puts "\[--help\] Print help information for this script"
puts "-------------------------------------------------------------------------\n"
exit 0
}
if { $::argc > 0 } {
for {set i 0} {$i < $::argc} {incr i} {
set option [string trim [lindex $::argv $i]]
switch -regexp -- $option {
"--origin_dir" { incr i; set origin_dir [lindex $::argv $i] }
"--project_name" { incr i; set _xil_proj_name_ [lindex $::argv $i] }
"--help" { print_help }
default {
if { [regexp {^-} $option] } {
puts "ERROR: Unknown option '$option' specified, please type '$script_file -tclargs --help' for usage info.\n"
return 1
}
}
}
}
}
# Set the directory path for the original project from where this script was exported
set orig_proj_dir "[file normalize "$origin_dir/Desktop/Research/ultra96_design/ultra96_design"]"
# Check for paths and files needed for project creation
set validate_required 0
if { $validate_required } {
if { [checkRequiredFiles $origin_dir] } {
puts "Tcl file $script_file is valid. All files required for project creation is accesable. "
} else {
puts "Tcl file $script_file is not valid. Not all files required for project creation is accesable. "
return
}
}
# Create project
create_project ${_xil_proj_name_} ./${_xil_proj_name_} -part xczu3eg-sbva484-1-i
# Set the directory path for the new project
set proj_dir [get_property directory [current_project]]
# Set project properties
set obj [current_project]
set_property -name "board_part" -value "avnet.com:ultra96v2:part0:1.2" -objects $obj
set_property -name "classic_soc_boot" -value "0" -objects $obj
set_property -name "compxlib.activehdl_compiled_library_dir" -value "$proj_dir/${_xil_proj_name_}.cache/compile_simlib/activehdl" -objects $obj
set_property -name "compxlib.funcsim" -value "1" -objects $obj
set_property -name "compxlib.modelsim_compiled_library_dir" -value "$proj_dir/${_xil_proj_name_}.cache/compile_simlib/modelsim" -objects $obj
set_property -name "compxlib.overwrite_libs" -value "0" -objects $obj
set_property -name "compxlib.questa_compiled_library_dir" -value "$proj_dir/${_xil_proj_name_}.cache/compile_simlib/questa" -objects $obj
set_property -name "compxlib.riviera_compiled_library_dir" -value "$proj_dir/${_xil_proj_name_}.cache/compile_simlib/riviera" -objects $obj
set_property -name "compxlib.timesim" -value "1" -objects $obj
set_property -name "compxlib.vcs_compiled_library_dir" -value "$proj_dir/${_xil_proj_name_}.cache/compile_simlib/vcs" -objects $obj
set_property -name "compxlib.xsim_compiled_library_dir" -value "" -objects $obj
set_property -name "corecontainer.enable" -value "0" -objects $obj
set_property -name "customized_default_ip_location" -value "" -objects $obj
set_property -name "default_lib" -value "xil_defaultlib" -objects $obj
set_property -name "enable_optional_runs_sta" -value "0" -objects $obj
set_property -name "enable_resource_estimation" -value "0" -objects $obj
set_property -name "enable_vhdl_2008" -value "1" -objects $obj
set_property -name "generate_ip_upgrade_log" -value "1" -objects $obj
set_property -name "ip_cache_permissions" -value "read write" -objects $obj
set_property -name "ip_interface_inference_priority" -value "" -objects $obj
set_property -name "ip_output_repo" -value "$proj_dir/${_xil_proj_name_}.cache/ip" -objects $obj
set_property -name "legacy_ip_repo_paths" -value "" -objects $obj
set_property -name "local_ip_repo_leaf_dir_name" -value "ip_repo" -objects $obj
set_property -name "mem.enable_memory_map_generation" -value "1" -objects $obj
set_property -name "platform.board_id" -value "ultra96v2" -objects $obj
set_property -name "platform.default_output_type" -value "undefined" -objects $obj
set_property -name "platform.design_intent.datacenter" -value "undefined" -objects $obj
set_property -name "platform.design_intent.embedded" -value "undefined" -objects $obj
set_property -name "platform.design_intent.external_host" -value "undefined" -objects $obj
set_property -name "platform.design_intent.server_managed" -value "undefined" -objects $obj
set_property -name "platform.rom.debug_type" -value "0" -objects $obj
set_property -name "platform.rom.prom_type" -value "0" -objects $obj
set_property -name "platform.slrconstraintmode" -value "0" -objects $obj
set_property -name "preferred_sim_model" -value "rtl" -objects $obj
set_property -name "project_type" -value "Default" -objects $obj
set_property -name "pr_flow" -value "0" -objects $obj
set_property -name "revised_directory_structure" -value "1" -objects $obj
set_property -name "sim.central_dir" -value "$proj_dir/${_xil_proj_name_}.ip_user_files" -objects $obj
set_property -name "sim.ip.auto_export_scripts" -value "1" -objects $obj
set_property -name "sim.use_ip_compiled_libs" -value "1" -objects $obj
set_property -name "simulator.activehdl_gcc_install_dir" -value "" -objects $obj
set_property -name "simulator.activehdl_install_dir" -value "" -objects $obj
set_property -name "simulator.modelsim_gcc_install_dir" -value "" -objects $obj
set_property -name "simulator.modelsim_install_dir" -value "" -objects $obj
set_property -name "simulator.questa_gcc_install_dir" -value "" -objects $obj
set_property -name "simulator.questa_install_dir" -value "" -objects $obj
set_property -name "simulator.riviera_gcc_install_dir" -value "" -objects $obj
set_property -name "simulator.riviera_install_dir" -value "" -objects $obj
set_property -name "simulator.vcs_gcc_install_dir" -value "" -objects $obj
set_property -name "simulator.vcs_install_dir" -value "" -objects $obj
set_property -name "simulator.xcelium_gcc_install_dir" -value "" -objects $obj
set_property -name "simulator.xcelium_install_dir" -value "" -objects $obj
set_property -name "simulator_language" -value "Mixed" -objects $obj
set_property -name "source_mgmt_mode" -value "All" -objects $obj
set_property -name "target_language" -value "Verilog" -objects $obj
set_property -name "target_simulator" -value "XSim" -objects $obj
set_property -name "tool_flow" -value "Vivado" -objects $obj
set_property -name "webtalk.activehdl_export_sim" -value "1" -objects $obj
set_property -name "webtalk.modelsim_export_sim" -value "1" -objects $obj
set_property -name "webtalk.questa_export_sim" -value "1" -objects $obj
set_property -name "webtalk.riviera_export_sim" -value "1" -objects $obj
set_property -name "webtalk.vcs_export_sim" -value "1" -objects $obj
set_property -name "webtalk.xcelium_export_sim" -value "1" -objects $obj
set_property -name "webtalk.xsim_export_sim" -value "1" -objects $obj
set_property -name "xpm_libraries" -value "XPM_CDC XPM_FIFO XPM_MEMORY" -objects $obj
set_property -name "xsim.array_display_limit" -value "1024" -objects $obj
set_property -name "xsim.radix" -value "hex" -objects $obj
set_property -name "xsim.time_unit" -value "ns" -objects $obj
set_property -name "xsim.trace_limit" -value "65536" -objects $obj
# Create 'sources_1' fileset (if not found)
if {[string equal [get_filesets -quiet sources_1] ""]} {
create_fileset -srcset sources_1
}
# Set IP repository paths
set obj [get_filesets sources_1]
if { $obj != {} } {
set_property "ip_repo_paths" "[file normalize "$origin_dir/Desktop/Research/ultra96_design/ip"]" $obj
# Rebuild user ip_repo's index before adding any source files
update_ip_catalog -rebuild
}
# Set 'sources_1' fileset object
set obj [get_filesets sources_1]
# Import local files from the original project
set files [list \
[file normalize "${origin_dir}/Desktop/Research/ultra96_design/ultra96_design/ultra96_design.srcs/sources_1/imports/hdl/design_1_wrapper.v"]\
]
set imported_files [import_files -fileset sources_1 $files]
# Set 'sources_1' fileset file properties for remote files
# None
# Set 'sources_1' fileset file properties for local files
set file "hdl/design_1_wrapper.v"
set file_obj [get_files -of_objects [get_filesets sources_1] [list "*$file"]]
set_property -name "file_type" -value "Verilog" -objects $file_obj
set_property -name "is_enabled" -value "1" -objects $file_obj
set_property -name "is_global_include" -value "0" -objects $file_obj
set_property -name "library" -value "xil_defaultlib" -objects $file_obj
set_property -name "path_mode" -value "RelativeFirst" -objects $file_obj
set_property -name "used_in" -value "synthesis implementation simulation" -objects $file_obj
set_property -name "used_in_implementation" -value "1" -objects $file_obj
set_property -name "used_in_simulation" -value "1" -objects $file_obj
set_property -name "used_in_synthesis" -value "1" -objects $file_obj
# Set 'sources_1' fileset properties
set obj [get_filesets sources_1]
set_property -name "dataflow_viewer_settings" -value "" -objects $obj
set_property -name "design_mode" -value "RTL" -objects $obj
set_property -name "edif_extra_search_paths" -value "" -objects $obj
set_property -name "elab_link_dcps" -value "1" -objects $obj
set_property -name "elab_load_timing_constraints" -value "1" -objects $obj
set_property -name "generic" -value "" -objects $obj
set_property -name "include_dirs" -value "" -objects $obj
set_property -name "lib_map_file" -value "" -objects $obj
set_property -name "loop_count" -value "1000" -objects $obj
set_property -name "name" -value "sources_1" -objects $obj
set_property -name "top" -value "design_1_wrapper" -objects $obj
set_property -name "verilog_define" -value "" -objects $obj
set_property -name "verilog_uppercase" -value "0" -objects $obj
set_property -name "verilog_version" -value "verilog_2001" -objects $obj
set_property -name "vhdl_version" -value "vhdl_2k" -objects $obj
# Create 'constrs_1' fileset (if not found)
if {[string equal [get_filesets -quiet constrs_1] ""]} {
create_fileset -constrset constrs_1
}
# Set 'constrs_1' fileset object
set obj [get_filesets constrs_1]
# Empty (no sources present)
# Set 'constrs_1' fileset properties
set obj [get_filesets constrs_1]
set_property -name "constrs_type" -value "XDC" -objects $obj
set_property -name "name" -value "constrs_1" -objects $obj
set_property -name "target_constrs_file" -value "" -objects $obj
# Create 'sim_1' fileset (if not found)
if {[string equal [get_filesets -quiet sim_1] ""]} {
create_fileset -simset sim_1
}
# Set 'sim_1' fileset object
set obj [get_filesets sim_1]
# Empty (no sources present)
# Set 'sim_1' fileset properties
set obj [get_filesets sim_1]
set_property -name "32bit" -value "0" -objects $obj
set_property -name "force_compile_glbl" -value "0" -objects $obj
set_property -name "force_no_compile_glbl" -value "0" -objects $obj
set_property -name "generate_scripts_only" -value "0" -objects $obj
set_property -name "generic" -value "" -objects $obj
set_property -name "hbs.configure_design_for_hier_access" -value "1" -objects $obj
set_property -name "hw_emu.debug_mode" -value "wdb" -objects $obj
set_property -name "include_dirs" -value "" -objects $obj
set_property -name "incremental" -value "1" -objects $obj
set_property -name "name" -value "sim_1" -objects $obj
set_property -name "nl.cell" -value "" -objects $obj
set_property -name "nl.incl_unisim_models" -value "0" -objects $obj
set_property -name "nl.process_corner" -value "slow" -objects $obj
set_property -name "nl.rename_top" -value "" -objects $obj
set_property -name "nl.sdf_anno" -value "1" -objects $obj
set_property -name "nl.write_all_overrides" -value "0" -objects $obj
set_property -name "simmodel_value_check" -value "1" -objects $obj
set_property -name "simulator_launch_mode" -value "off" -objects $obj
set_property -name "source_set" -value "sources_1" -objects $obj
set_property -name "systemc_include_dirs" -value "" -objects $obj
set_property -name "top" -value "design_1_wrapper" -objects $obj
set_property -name "top_lib" -value "xil_defaultlib" -objects $obj
set_property -name "transport_int_delay" -value "0" -objects $obj
set_property -name "transport_path_delay" -value "0" -objects $obj
set_property -name "unifast" -value "0" -objects $obj
set_property -name "verilog_define" -value "" -objects $obj
set_property -name "verilog_uppercase" -value "0" -objects $obj
set_property -name "xelab.dll" -value "0" -objects $obj
set_property -name "xsim.compile.tcl.pre" -value "" -objects $obj
set_property -name "xsim.compile.xsc.more_options" -value "" -objects $obj
set_property -name "xsim.compile.xvhdl.more_options" -value "" -objects $obj
set_property -name "xsim.compile.xvhdl.nosort" -value "1" -objects $obj
set_property -name "xsim.compile.xvhdl.relax" -value "1" -objects $obj
set_property -name "xsim.compile.xvlog.more_options" -value "" -objects $obj
set_property -name "xsim.compile.xvlog.nosort" -value "1" -objects $obj
set_property -name "xsim.compile.xvlog.relax" -value "1" -objects $obj
set_property -name "xsim.elaborate.coverage.celldefine" -value "0" -objects $obj
set_property -name "xsim.elaborate.coverage.dir" -value "" -objects $obj
set_property -name "xsim.elaborate.coverage.library" -value "0" -objects $obj
set_property -name "xsim.elaborate.coverage.name" -value "" -objects $obj
set_property -name "xsim.elaborate.coverage.type" -value "" -objects $obj
set_property -name "xsim.elaborate.debug_level" -value "typical" -objects $obj
set_property -name "xsim.elaborate.link.c" -value "" -objects $obj
set_property -name "xsim.elaborate.link.sysc" -value "" -objects $obj
set_property -name "xsim.elaborate.load_glbl" -value "1" -objects $obj
set_property -name "xsim.elaborate.mt_level" -value "auto" -objects $obj
set_property -name "xsim.elaborate.rangecheck" -value "0" -objects $obj
set_property -name "xsim.elaborate.relax" -value "1" -objects $obj
set_property -name "xsim.elaborate.sdf_delay" -value "sdfmax" -objects $obj
set_property -name "xsim.elaborate.snapshot" -value "" -objects $obj
set_property -name "xsim.elaborate.xelab.more_options" -value "" -objects $obj
set_property -name "xsim.elaborate.xsc.more_options" -value "" -objects $obj
set_property -name "xsim.simulate.add_positional" -value "0" -objects $obj
set_property -name "xsim.simulate.custom_tcl" -value "" -objects $obj
set_property -name "xsim.simulate.log_all_signals" -value "0" -objects $obj
set_property -name "xsim.simulate.no_quit" -value "0" -objects $obj
set_property -name "xsim.simulate.runtime" -value "1000ns" -objects $obj
set_property -name "xsim.simulate.saif" -value "" -objects $obj
set_property -name "xsim.simulate.saif_all_signals" -value "0" -objects $obj
set_property -name "xsim.simulate.saif_scope" -value "" -objects $obj
set_property -name "xsim.simulate.tcl.post" -value "" -objects $obj
set_property -name "xsim.simulate.wdb" -value "" -objects $obj
set_property -name "xsim.simulate.xsim.more_options" -value "" -objects $obj
# Set 'utils_1' fileset object
set obj [get_filesets utils_1]
# Empty (no sources present)
# Set 'utils_1' fileset properties
set obj [get_filesets utils_1]
set_property -name "name" -value "utils_1" -objects $obj
# Adding sources referenced in BDs, if not already added
# Proc to create BD design_1
proc cr_bd_design_1 { parentCell } {
# CHANGE DESIGN NAME HERE
set design_name design_1
common::send_gid_msg -ssname BD::TCL -id 2010 -severity "INFO" "Currently there is no design <$design_name> in project, so creating one..."
create_bd_design $design_name
set bCheckIPsPassed 1
##################################################################
# CHECK IPs
##################################################################
set bCheckIPs 1
if { $bCheckIPs == 1 } {
set list_check_ips "\
xilinx.com:ip:axi_vdma:6.3\
xilinx.com:ip:clk_wiz:6.0\
xilinx.com:hls:demosaic_root:1.0\
xilinx.com:ip:mipi_csi2_rx_subsystem:5.1\
xilinx.com:ip:proc_sys_reset:5.0\
xilinx.com:ip:util_vector_logic:2.0\
xilinx.com:ip:zynq_ultra_ps_e:3.4\
"
set list_ips_missing ""
common::send_gid_msg -ssname BD::TCL -id 2011 -severity "INFO" "Checking if the following IPs exist in the project's IP catalog: $list_check_ips ."
foreach ip_vlnv $list_check_ips {
set ip_obj [get_ipdefs -all $ip_vlnv]
if { $ip_obj eq "" } {
lappend list_ips_missing $ip_vlnv
}
}
if { $list_ips_missing ne "" } {
catch {common::send_gid_msg -ssname BD::TCL -id 2012 -severity "ERROR" "The following IPs are not found in the IP Catalog:\n $list_ips_missing\n\nResolution: Please add the repository containing the IP(s) to the project." }
set bCheckIPsPassed 0
}
}
if { $bCheckIPsPassed != 1 } {
common::send_gid_msg -ssname BD::TCL -id 2023 -severity "WARNING" "Will not continue with creation of design due to the error(s) above."
return 3
}
variable script_folder
if { $parentCell eq "" } {
set parentCell [get_bd_cells /]
}
# Get object for parentCell
set parentObj [get_bd_cells $parentCell]
if { $parentObj == "" } {
catch {common::send_gid_msg -ssname BD::TCL -id 2090 -severity "ERROR" "Unable to find parent cell <$parentCell>!"}
return
}
# Make sure parentObj is hier blk
set parentType [get_property TYPE $parentObj]
if { $parentType ne "hier" } {
catch {common::send_gid_msg -ssname BD::TCL -id 2091 -severity "ERROR" "Parent <$parentObj> has TYPE = <$parentType>. Expected to be <hier>."}
return
}
# Save current instance; Restore later
set oldCurInst [current_bd_instance .]
# Set parent object as current
current_bd_instance $parentObj
# Create interface ports
set mipi_phy_csi [ create_bd_intf_port -mode Slave -vlnv xilinx.com:interface:mipi_phy_rtl:1.0 mipi_phy_csi ]
# Create ports
# Create instance: axi_vdma_0, and set properties
set axi_vdma_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:axi_vdma:6.3 axi_vdma_0 ]
set_property -dict [ list \
CONFIG.c_include_mm2s {0} \
CONFIG.c_m_axi_s2mm_data_width {128} \
CONFIG.c_mm2s_genlock_mode {0} \
] $axi_vdma_0
# Create instance: clk_wiz_0, and set properties
set clk_wiz_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:clk_wiz:6.0 clk_wiz_0 ]
set_property -dict [ list \
CONFIG.CLKOUT1_JITTER {102.086} \
CONFIG.CLKOUT1_REQUESTED_OUT_FREQ {200.000} \
CONFIG.CLKOUT2_JITTER {115.831} \
CONFIG.CLKOUT2_PHASE_ERROR {87.180} \
CONFIG.CLKOUT2_USED {false} \
CONFIG.MMCM_CLKOUT0_DIVIDE_F {6.000} \
CONFIG.MMCM_CLKOUT1_DIVIDE {1} \
CONFIG.MMCM_DIVCLK_DIVIDE {1} \
CONFIG.NUM_OUT_CLKS {1} \
] $clk_wiz_0
# Create instance: demosaic_root_0, and set properties
set demosaic_root_0 [ create_bd_cell -type ip -vlnv xilinx.com:hls:demosaic_root:1.0 demosaic_root_0 ]
# Create instance: mipi_csi2_rx_subsyst_0, and set properties
set mipi_csi2_rx_subsyst_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:mipi_csi2_rx_subsystem:5.1 mipi_csi2_rx_subsyst_0 ]
set_property -dict [ list \
CONFIG.CLK_LANE_IO_LOC {N2} \
CONFIG.CLK_LANE_IO_LOC_NAME {IO_L7P_T1L_N0_QBC_AD13P_65} \
CONFIG.CMN_NUM_LANES {2} \
CONFIG.CMN_NUM_PIXELS {4} \
CONFIG.CMN_PXL_FORMAT {RAW10} \
CONFIG.CMN_VC {All} \
CONFIG.C_CLK_LANE_IO_POSITION {13} \
CONFIG.C_DATA_LANE0_IO_POSITION {15} \
CONFIG.C_DATA_LANE1_IO_POSITION {17} \
CONFIG.C_DPHY_LANES {2} \
CONFIG.C_EN_BG0_PIN0 {false} \
CONFIG.C_HS_LINE_RATE {1000} \
CONFIG.C_HS_SETTLE_NS {145} \
CONFIG.DATA_LANE0_IO_LOC {N5} \
CONFIG.DATA_LANE0_IO_LOC_NAME {IO_L8P_T1L_N2_AD5P_65} \
CONFIG.DATA_LANE1_IO_LOC {M2} \
CONFIG.DATA_LANE1_IO_LOC_NAME {IO_L9P_T1L_N4_AD12P_65} \
CONFIG.DPY_LINE_RATE {1000} \
CONFIG.SupportLevel {1} \
] $mipi_csi2_rx_subsyst_0
# Create instance: ps8_0_axi_periph, and set properties
set ps8_0_axi_periph [ create_bd_cell -type ip -vlnv xilinx.com:ip:axi_interconnect:2.1 ps8_0_axi_periph ]
set_property -dict [ list \
CONFIG.NUM_MI {3} \
] $ps8_0_axi_periph
# Create instance: rst_ps8_0_99M, and set properties
set rst_ps8_0_99M [ create_bd_cell -type ip -vlnv xilinx.com:ip:proc_sys_reset:5.0 rst_ps8_0_99M ]
# Create instance: util_vector_logic_0, and set properties
set util_vector_logic_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:util_vector_logic:2.0 util_vector_logic_0 ]
set_property -dict [ list \
CONFIG.C_OPERATION {not} \
CONFIG.C_SIZE {1} \
] $util_vector_logic_0
# Create instance: zynq_ultra_ps_e_0, and set properties
set zynq_ultra_ps_e_0 [ create_bd_cell -type ip -vlnv xilinx.com:ip:zynq_ultra_ps_e:3.4 zynq_ultra_ps_e_0 ]
set_property -dict [ list \
CONFIG.CAN0_BOARD_INTERFACE {custom} \
CONFIG.CAN1_BOARD_INTERFACE {custom} \
CONFIG.CSU_BOARD_INTERFACE {custom} \
CONFIG.DP_BOARD_INTERFACE {custom} \
CONFIG.GEM0_BOARD_INTERFACE {custom} \
CONFIG.GEM1_BOARD_INTERFACE {custom} \
CONFIG.GEM2_BOARD_INTERFACE {custom} \
CONFIG.GEM3_BOARD_INTERFACE {custom} \
CONFIG.GPIO_BOARD_INTERFACE {custom} \
CONFIG.IIC0_BOARD_INTERFACE {custom} \
CONFIG.IIC1_BOARD_INTERFACE {custom} \
CONFIG.NAND_BOARD_INTERFACE {custom} \
CONFIG.PCIE_BOARD_INTERFACE {custom} \
CONFIG.PJTAG_BOARD_INTERFACE {custom} \
CONFIG.PMU_BOARD_INTERFACE {custom} \
CONFIG.PSU_BANK_0_IO_STANDARD {LVCMOS18} \
CONFIG.PSU_BANK_1_IO_STANDARD {LVCMOS18} \
CONFIG.PSU_BANK_2_IO_STANDARD {LVCMOS18} \
CONFIG.PSU_BANK_3_IO_STANDARD {LVCMOS18} \
CONFIG.PSU_DDR_RAM_HIGHADDR {0x7FFFFFFF} \
CONFIG.PSU_DDR_RAM_HIGHADDR_OFFSET {0x00000002} \
CONFIG.PSU_DDR_RAM_LOWADDR_OFFSET {0x80000000} \
CONFIG.PSU_DYNAMIC_DDR_CONFIG_EN {0} \
CONFIG.PSU_IMPORT_BOARD_PRESET {} \
CONFIG.PSU_MIO_0_DIRECTION {out} \
CONFIG.PSU_MIO_0_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_0_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_0_POLARITY {Default} \
CONFIG.PSU_MIO_0_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_0_SLEW {fast} \
CONFIG.PSU_MIO_10_DIRECTION {inout} \
CONFIG.PSU_MIO_10_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_10_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_10_POLARITY {Default} \
CONFIG.PSU_MIO_10_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_10_SLEW {fast} \
CONFIG.PSU_MIO_11_DIRECTION {inout} \
CONFIG.PSU_MIO_11_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_11_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_11_POLARITY {Default} \
CONFIG.PSU_MIO_11_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_11_SLEW {fast} \
CONFIG.PSU_MIO_12_DIRECTION {inout} \
CONFIG.PSU_MIO_12_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_12_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_12_POLARITY {Default} \
CONFIG.PSU_MIO_12_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_12_SLEW {fast} \
CONFIG.PSU_MIO_13_DIRECTION {inout} \
CONFIG.PSU_MIO_13_DRIVE_STRENGTH {4} \
CONFIG.PSU_MIO_13_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_13_POLARITY {Default} \
CONFIG.PSU_MIO_13_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_13_SLEW {fast} \
CONFIG.PSU_MIO_14_DIRECTION {inout} \
CONFIG.PSU_MIO_14_DRIVE_STRENGTH {4} \
CONFIG.PSU_MIO_14_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_14_POLARITY {Default} \
CONFIG.PSU_MIO_14_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_14_SLEW {fast} \
CONFIG.PSU_MIO_15_DIRECTION {inout} \
CONFIG.PSU_MIO_15_DRIVE_STRENGTH {4} \
CONFIG.PSU_MIO_15_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_15_POLARITY {Default} \
CONFIG.PSU_MIO_15_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_15_SLEW {fast} \
CONFIG.PSU_MIO_16_DIRECTION {inout} \
CONFIG.PSU_MIO_16_DRIVE_STRENGTH {4} \
CONFIG.PSU_MIO_16_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_16_POLARITY {Default} \
CONFIG.PSU_MIO_16_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_16_SLEW {fast} \
CONFIG.PSU_MIO_17_DIRECTION {inout} \
CONFIG.PSU_MIO_17_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_17_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_17_POLARITY {Default} \
CONFIG.PSU_MIO_17_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_17_SLEW {fast} \
CONFIG.PSU_MIO_18_DIRECTION {inout} \
CONFIG.PSU_MIO_18_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_18_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_18_POLARITY {Default} \
CONFIG.PSU_MIO_18_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_18_SLEW {fast} \
CONFIG.PSU_MIO_19_DIRECTION {inout} \
CONFIG.PSU_MIO_19_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_19_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_19_POLARITY {Default} \
CONFIG.PSU_MIO_19_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_19_SLEW {fast} \
CONFIG.PSU_MIO_1_DIRECTION {in} \
CONFIG.PSU_MIO_1_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_1_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_1_POLARITY {Default} \
CONFIG.PSU_MIO_1_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_1_SLEW {fast} \
CONFIG.PSU_MIO_20_DIRECTION {inout} \
CONFIG.PSU_MIO_20_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_20_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_20_POLARITY {Default} \
CONFIG.PSU_MIO_20_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_20_SLEW {fast} \
CONFIG.PSU_MIO_21_DIRECTION {inout} \
CONFIG.PSU_MIO_21_DRIVE_STRENGTH {4} \
CONFIG.PSU_MIO_21_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_21_POLARITY {Default} \
CONFIG.PSU_MIO_21_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_21_SLEW {fast} \
CONFIG.PSU_MIO_22_DIRECTION {out} \
CONFIG.PSU_MIO_22_DRIVE_STRENGTH {4} \
CONFIG.PSU_MIO_22_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_22_POLARITY {Default} \
CONFIG.PSU_MIO_22_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_22_SLEW {fast} \
CONFIG.PSU_MIO_23_DIRECTION {inout} \
CONFIG.PSU_MIO_23_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_23_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_23_POLARITY {Default} \
CONFIG.PSU_MIO_23_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_23_SLEW {fast} \
CONFIG.PSU_MIO_24_DIRECTION {in} \
CONFIG.PSU_MIO_24_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_24_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_24_POLARITY {Default} \
CONFIG.PSU_MIO_24_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_24_SLEW {fast} \
CONFIG.PSU_MIO_25_DIRECTION {inout} \
CONFIG.PSU_MIO_25_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_25_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_25_POLARITY {Default} \
CONFIG.PSU_MIO_25_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_25_SLEW {fast} \
CONFIG.PSU_MIO_26_DIRECTION {in} \
CONFIG.PSU_MIO_26_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_26_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_26_POLARITY {Default} \
CONFIG.PSU_MIO_26_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_26_SLEW {fast} \
CONFIG.PSU_MIO_27_DIRECTION {out} \
CONFIG.PSU_MIO_27_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_27_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_27_POLARITY {Default} \
CONFIG.PSU_MIO_27_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_27_SLEW {fast} \
CONFIG.PSU_MIO_28_DIRECTION {in} \
CONFIG.PSU_MIO_28_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_28_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_28_POLARITY {Default} \
CONFIG.PSU_MIO_28_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_28_SLEW {fast} \
CONFIG.PSU_MIO_29_DIRECTION {out} \
CONFIG.PSU_MIO_29_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_29_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_29_POLARITY {Default} \
CONFIG.PSU_MIO_29_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_29_SLEW {fast} \
CONFIG.PSU_MIO_2_DIRECTION {in} \
CONFIG.PSU_MIO_2_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_2_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_2_POLARITY {Default} \
CONFIG.PSU_MIO_2_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_2_SLEW {fast} \
CONFIG.PSU_MIO_30_DIRECTION {in} \
CONFIG.PSU_MIO_30_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_30_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_30_POLARITY {Default} \
CONFIG.PSU_MIO_30_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_30_SLEW {fast} \
CONFIG.PSU_MIO_31_DIRECTION {inout} \
CONFIG.PSU_MIO_31_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_31_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_31_POLARITY {Default} \
CONFIG.PSU_MIO_31_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_31_SLEW {fast} \
CONFIG.PSU_MIO_32_DIRECTION {out} \
CONFIG.PSU_MIO_32_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_32_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_32_POLARITY {Default} \
CONFIG.PSU_MIO_32_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_32_SLEW {fast} \
CONFIG.PSU_MIO_33_DIRECTION {out} \
CONFIG.PSU_MIO_33_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_33_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_33_POLARITY {Default} \
CONFIG.PSU_MIO_33_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_33_SLEW {fast} \
CONFIG.PSU_MIO_34_DIRECTION {out} \
CONFIG.PSU_MIO_34_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_34_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_34_POLARITY {Default} \
CONFIG.PSU_MIO_34_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_34_SLEW {fast} \
CONFIG.PSU_MIO_35_DIRECTION {inout} \
CONFIG.PSU_MIO_35_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_35_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_35_POLARITY {Default} \
CONFIG.PSU_MIO_35_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_35_SLEW {fast} \
CONFIG.PSU_MIO_36_DIRECTION {inout} \
CONFIG.PSU_MIO_36_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_36_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_36_POLARITY {Default} \
CONFIG.PSU_MIO_36_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_36_SLEW {fast} \
CONFIG.PSU_MIO_37_DIRECTION {inout} \
CONFIG.PSU_MIO_37_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_37_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_37_POLARITY {Default} \
CONFIG.PSU_MIO_37_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_37_SLEW {fast} \
CONFIG.PSU_MIO_38_DIRECTION {inout} \
CONFIG.PSU_MIO_38_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_38_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_38_POLARITY {Default} \
CONFIG.PSU_MIO_38_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_38_SLEW {fast} \
CONFIG.PSU_MIO_39_DIRECTION {inout} \
CONFIG.PSU_MIO_39_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_39_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_39_POLARITY {Default} \
CONFIG.PSU_MIO_39_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_39_SLEW {slow} \
CONFIG.PSU_MIO_3_DIRECTION {out} \
CONFIG.PSU_MIO_3_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_3_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_3_POLARITY {Default} \
CONFIG.PSU_MIO_3_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_3_SLEW {fast} \
CONFIG.PSU_MIO_40_DIRECTION {inout} \
CONFIG.PSU_MIO_40_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_40_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_40_POLARITY {Default} \
CONFIG.PSU_MIO_40_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_40_SLEW {fast} \
CONFIG.PSU_MIO_41_DIRECTION {inout} \
CONFIG.PSU_MIO_41_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_41_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_41_POLARITY {Default} \
CONFIG.PSU_MIO_41_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_41_SLEW {fast} \
CONFIG.PSU_MIO_42_DIRECTION {inout} \
CONFIG.PSU_MIO_42_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_42_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_42_POLARITY {Default} \
CONFIG.PSU_MIO_42_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_42_SLEW {fast} \
CONFIG.PSU_MIO_43_DIRECTION {inout} \
CONFIG.PSU_MIO_43_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_43_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_43_POLARITY {Default} \
CONFIG.PSU_MIO_43_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_43_SLEW {fast} \
CONFIG.PSU_MIO_44_DIRECTION {inout} \
CONFIG.PSU_MIO_44_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_44_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_44_POLARITY {Default} \
CONFIG.PSU_MIO_44_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_44_SLEW {fast} \
CONFIG.PSU_MIO_45_DIRECTION {inout} \
CONFIG.PSU_MIO_45_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_45_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_45_POLARITY {Default} \
CONFIG.PSU_MIO_45_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_45_SLEW {fast} \
CONFIG.PSU_MIO_46_DIRECTION {inout} \
CONFIG.PSU_MIO_46_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_46_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_46_POLARITY {Default} \
CONFIG.PSU_MIO_46_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_46_SLEW {fast} \
CONFIG.PSU_MIO_47_DIRECTION {inout} \
CONFIG.PSU_MIO_47_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_47_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_47_POLARITY {Default} \
CONFIG.PSU_MIO_47_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_47_SLEW {fast} \
CONFIG.PSU_MIO_48_DIRECTION {inout} \
CONFIG.PSU_MIO_48_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_48_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_48_POLARITY {Default} \
CONFIG.PSU_MIO_48_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_48_SLEW {fast} \
CONFIG.PSU_MIO_49_DIRECTION {inout} \
CONFIG.PSU_MIO_49_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_49_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_49_POLARITY {Default} \
CONFIG.PSU_MIO_49_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_49_SLEW {fast} \
CONFIG.PSU_MIO_4_DIRECTION {inout} \
CONFIG.PSU_MIO_4_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_4_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_4_POLARITY {Default} \
CONFIG.PSU_MIO_4_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_4_SLEW {fast} \
CONFIG.PSU_MIO_50_DIRECTION {inout} \
CONFIG.PSU_MIO_50_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_50_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_50_POLARITY {Default} \
CONFIG.PSU_MIO_50_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_50_SLEW {fast} \
CONFIG.PSU_MIO_51_DIRECTION {out} \
CONFIG.PSU_MIO_51_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_51_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_51_POLARITY {Default} \
CONFIG.PSU_MIO_51_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_51_SLEW {fast} \
CONFIG.PSU_MIO_52_DIRECTION {in} \
CONFIG.PSU_MIO_52_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_52_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_52_POLARITY {Default} \
CONFIG.PSU_MIO_52_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_52_SLEW {fast} \
CONFIG.PSU_MIO_53_DIRECTION {in} \
CONFIG.PSU_MIO_53_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_53_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_53_POLARITY {Default} \
CONFIG.PSU_MIO_53_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_53_SLEW {fast} \
CONFIG.PSU_MIO_54_DIRECTION {inout} \
CONFIG.PSU_MIO_54_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_54_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_54_POLARITY {Default} \
CONFIG.PSU_MIO_54_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_54_SLEW {fast} \
CONFIG.PSU_MIO_55_DIRECTION {in} \
CONFIG.PSU_MIO_55_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_55_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_55_POLARITY {Default} \
CONFIG.PSU_MIO_55_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_55_SLEW {fast} \
CONFIG.PSU_MIO_56_DIRECTION {inout} \
CONFIG.PSU_MIO_56_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_56_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_56_POLARITY {Default} \
CONFIG.PSU_MIO_56_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_56_SLEW {fast} \
CONFIG.PSU_MIO_57_DIRECTION {inout} \
CONFIG.PSU_MIO_57_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_57_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_57_POLARITY {Default} \
CONFIG.PSU_MIO_57_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_57_SLEW {fast} \
CONFIG.PSU_MIO_58_DIRECTION {out} \
CONFIG.PSU_MIO_58_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_58_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_58_POLARITY {Default} \
CONFIG.PSU_MIO_58_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_58_SLEW {fast} \
CONFIG.PSU_MIO_59_DIRECTION {inout} \
CONFIG.PSU_MIO_59_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_59_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_59_POLARITY {Default} \
CONFIG.PSU_MIO_59_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_59_SLEW {fast} \
CONFIG.PSU_MIO_5_DIRECTION {inout} \
CONFIG.PSU_MIO_5_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_5_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_5_POLARITY {Default} \
CONFIG.PSU_MIO_5_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_5_SLEW {fast} \
CONFIG.PSU_MIO_60_DIRECTION {inout} \
CONFIG.PSU_MIO_60_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_60_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_60_POLARITY {Default} \
CONFIG.PSU_MIO_60_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_60_SLEW {fast} \
CONFIG.PSU_MIO_61_DIRECTION {inout} \
CONFIG.PSU_MIO_61_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_61_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_61_POLARITY {Default} \
CONFIG.PSU_MIO_61_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_61_SLEW {fast} \
CONFIG.PSU_MIO_62_DIRECTION {inout} \
CONFIG.PSU_MIO_62_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_62_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_62_POLARITY {Default} \
CONFIG.PSU_MIO_62_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_62_SLEW {fast} \
CONFIG.PSU_MIO_63_DIRECTION {inout} \
CONFIG.PSU_MIO_63_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_63_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_63_POLARITY {Default} \
CONFIG.PSU_MIO_63_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_63_SLEW {fast} \
CONFIG.PSU_MIO_64_DIRECTION {in} \
CONFIG.PSU_MIO_64_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_64_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_64_POLARITY {Default} \
CONFIG.PSU_MIO_64_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_64_SLEW {fast} \
CONFIG.PSU_MIO_65_DIRECTION {in} \
CONFIG.PSU_MIO_65_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_65_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_65_POLARITY {Default} \
CONFIG.PSU_MIO_65_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_65_SLEW {fast} \
CONFIG.PSU_MIO_66_DIRECTION {inout} \
CONFIG.PSU_MIO_66_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_66_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_66_POLARITY {Default} \
CONFIG.PSU_MIO_66_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_66_SLEW {fast} \
CONFIG.PSU_MIO_67_DIRECTION {in} \
CONFIG.PSU_MIO_67_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_67_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_67_POLARITY {Default} \
CONFIG.PSU_MIO_67_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_67_SLEW {fast} \
CONFIG.PSU_MIO_68_DIRECTION {inout} \
CONFIG.PSU_MIO_68_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_68_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_68_POLARITY {Default} \
CONFIG.PSU_MIO_68_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_68_SLEW {fast} \
CONFIG.PSU_MIO_69_DIRECTION {inout} \
CONFIG.PSU_MIO_69_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_69_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_69_POLARITY {Default} \
CONFIG.PSU_MIO_69_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_69_SLEW {fast} \
CONFIG.PSU_MIO_6_DIRECTION {inout} \
CONFIG.PSU_MIO_6_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_6_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_6_POLARITY {Default} \
CONFIG.PSU_MIO_6_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_6_SLEW {fast} \
CONFIG.PSU_MIO_70_DIRECTION {out} \
CONFIG.PSU_MIO_70_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_70_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_70_POLARITY {Default} \
CONFIG.PSU_MIO_70_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_70_SLEW {fast} \
CONFIG.PSU_MIO_71_DIRECTION {inout} \
CONFIG.PSU_MIO_71_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_71_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_71_POLARITY {Default} \
CONFIG.PSU_MIO_71_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_71_SLEW {fast} \
CONFIG.PSU_MIO_72_DIRECTION {inout} \
CONFIG.PSU_MIO_72_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_72_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_72_POLARITY {Default} \
CONFIG.PSU_MIO_72_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_72_SLEW {fast} \
CONFIG.PSU_MIO_73_DIRECTION {inout} \
CONFIG.PSU_MIO_73_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_73_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_73_POLARITY {Default} \
CONFIG.PSU_MIO_73_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_73_SLEW {fast} \
CONFIG.PSU_MIO_74_DIRECTION {inout} \
CONFIG.PSU_MIO_74_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_74_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_74_POLARITY {Default} \
CONFIG.PSU_MIO_74_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_74_SLEW {fast} \
CONFIG.PSU_MIO_75_DIRECTION {inout} \
CONFIG.PSU_MIO_75_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_75_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_75_POLARITY {Default} \
CONFIG.PSU_MIO_75_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_75_SLEW {fast} \
CONFIG.PSU_MIO_76_DIRECTION {inout} \
CONFIG.PSU_MIO_76_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_76_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_76_POLARITY {Default} \
CONFIG.PSU_MIO_76_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_76_SLEW {fast} \
CONFIG.PSU_MIO_77_DIRECTION {inout} \
CONFIG.PSU_MIO_77_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_77_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_77_POLARITY {Default} \
CONFIG.PSU_MIO_77_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_77_SLEW {fast} \
CONFIG.PSU_MIO_7_DIRECTION {inout} \
CONFIG.PSU_MIO_7_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_7_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_7_POLARITY {Default} \
CONFIG.PSU_MIO_7_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_7_SLEW {fast} \
CONFIG.PSU_MIO_8_DIRECTION {inout} \
CONFIG.PSU_MIO_8_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_8_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_8_POLARITY {Default} \
CONFIG.PSU_MIO_8_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_8_SLEW {fast} \
CONFIG.PSU_MIO_9_DIRECTION {inout} \
CONFIG.PSU_MIO_9_DRIVE_STRENGTH {12} \
CONFIG.PSU_MIO_9_INPUT_TYPE {cmos} \
CONFIG.PSU_MIO_9_POLARITY {Default} \
CONFIG.PSU_MIO_9_PULLUPDOWN {pullup} \
CONFIG.PSU_MIO_9_SLEW {fast} \
CONFIG.PSU_MIO_TREE_PERIPHERALS {\
UART 1#UART 1#UART 0#UART 0#I2C 1#I2C 1#SPI 1#GPIO0 MIO#GPIO0 MIO#SPI 1#SPI\
1#SPI 1#GPIO0 MIO#SD 0#SD 0#SD 0#SD 0#GPIO0 MIO#GPIO0 MIO#GPIO0 MIO#GPIO0\
MIO#SD 0#SD 0#GPIO0 MIO#SD 0#GPIO0 MIO#PMU GPI 0#DPAUX#DPAUX#DPAUX#DPAUX#GPIO1\
MIO#PMU GPO 0#PMU GPO 1#PMU GPO 2#GPIO1 MIO#GPIO1 MIO#GPIO1 MIO#SPI 0#GPIO1\
MIO#GPIO1 MIO#SPI 0#SPI 0#SPI 0#GPIO1 MIO#GPIO1 MIO#SD 1#SD 1#SD 1#SD 1#SD 1#SD\
1#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB 0#USB\
1#USB 1#USB 1#USB 1#USB 1#USB 1#USB 1#USB 1#USB 1#USB 1#USB 1#USB 1#GPIO2\
MIO#GPIO2 MIO} \
CONFIG.PSU_MIO_TREE_SIGNALS {\
txd#rxd#rxd#txd#scl_out#sda_out#sclk_out#gpio0[7]#gpio0[8]#n_ss_out[0]#miso#mosi#gpio0[12]#sdio0_data_out[0]#sdio0_data_out[1]#sdio0_data_out[2]#sdio0_data_out[3]#gpio0[17]#gpio0[18]#gpio0[19]#gpio0[20]#sdio0_cmd_out#sdio0_clk_out#gpio0[23]#sdio0_cd_n#gpio0[25]#gpi[0]#dp_aux_data_out#dp_hot_plug_detect#dp_aux_data_oe#dp_aux_data_in#gpio1[31]#gpo[0]#gpo[1]#gpo[2]#gpio1[35]#gpio1[36]#gpio1[37]#sclk_out#gpio1[39]#gpio1[40]#n_ss_out[0]#miso#mosi#gpio1[44]#gpio1[45]#sdio1_data_out[0]#sdio1_data_out[1]#sdio1_data_out[2]#sdio1_data_out[3]#sdio1_cmd_out#sdio1_clk_out#ulpi_clk_in#ulpi_dir#ulpi_tx_data[2]#ulpi_nxt#ulpi_tx_data[0]#ulpi_tx_data[1]#ulpi_stp#ulpi_tx_data[3]#ulpi_tx_data[4]#ulpi_tx_data[5]#ulpi_tx_data[6]#ulpi_tx_data[7]#ulpi_clk_in#ulpi_dir#ulpi_tx_data[2]#ulpi_nxt#ulpi_tx_data[0]#ulpi_tx_data[1]#ulpi_stp#ulpi_tx_data[3]#ulpi_tx_data[4]#ulpi_tx_data[5]#ulpi_tx_data[6]#ulpi_tx_data[7]#gpio2[76]#gpio2[77]} \
CONFIG.PSU_PERIPHERAL_BOARD_PRESET {} \
CONFIG.PSU_SD0_INTERNAL_BUS_WIDTH {4} \
CONFIG.PSU_SD1_INTERNAL_BUS_WIDTH {4} \
CONFIG.PSU_SMC_CYCLE_T0 {NA} \
CONFIG.PSU_SMC_CYCLE_T1 {NA} \
CONFIG.PSU_SMC_CYCLE_T2 {NA} \
CONFIG.PSU_SMC_CYCLE_T3 {NA} \
CONFIG.PSU_SMC_CYCLE_T4 {NA} \
CONFIG.PSU_SMC_CYCLE_T5 {NA} \
CONFIG.PSU_SMC_CYCLE_T6 {NA} \
CONFIG.PSU_USB3__DUAL_CLOCK_ENABLE {1} \
CONFIG.PSU_VALUE_SILVERSION {3} \
CONFIG.PSU__ACPU0__POWER__ON {1} \
CONFIG.PSU__ACPU1__POWER__ON {1} \
CONFIG.PSU__ACPU2__POWER__ON {1} \
CONFIG.PSU__ACPU3__POWER__ON {1} \
CONFIG.PSU__ACTUAL__IP {1} \
CONFIG.PSU__ACT_DDR_FREQ_MHZ {533.333313} \
CONFIG.PSU__AFI0_COHERENCY {0} \
CONFIG.PSU__AFI1_COHERENCY {0} \
CONFIG.PSU__AUX_REF_CLK__FREQMHZ {33.333} \
CONFIG.PSU__CAN0_LOOP_CAN1__ENABLE {0} \
CONFIG.PSU__CAN0__GRP_CLK__ENABLE {0} \
CONFIG.PSU__CAN0__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__CAN1__GRP_CLK__ENABLE {0} \
CONFIG.PSU__CAN1__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__CRF_APB__ACPU_CTRL__ACT_FREQMHZ {1200.000000} \
CONFIG.PSU__CRF_APB__ACPU_CTRL__DIVISOR0 {1} \
CONFIG.PSU__CRF_APB__ACPU_CTRL__FREQMHZ {1200} \
CONFIG.PSU__CRF_APB__ACPU_CTRL__SRCSEL {APLL} \
CONFIG.PSU__CRF_APB__ACPU__FRAC_ENABLED {0} \
CONFIG.PSU__CRF_APB__AFI0_REF_CTRL__ACT_FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI0_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__AFI0_REF_CTRL__FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI0_REF_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__AFI0_REF__ENABLE {0} \
CONFIG.PSU__CRF_APB__AFI1_REF_CTRL__ACT_FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI1_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__AFI1_REF_CTRL__FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI1_REF_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__AFI1_REF__ENABLE {0} \
CONFIG.PSU__CRF_APB__AFI2_REF_CTRL__ACT_FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI2_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__AFI2_REF_CTRL__FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI2_REF_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__AFI2_REF__ENABLE {0} \
CONFIG.PSU__CRF_APB__AFI3_REF_CTRL__ACT_FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI3_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__AFI3_REF_CTRL__FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI3_REF_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__AFI3_REF__ENABLE {0} \
CONFIG.PSU__CRF_APB__AFI4_REF_CTRL__ACT_FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI4_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__AFI4_REF_CTRL__FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI4_REF_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__AFI4_REF__ENABLE {0} \
CONFIG.PSU__CRF_APB__AFI5_REF_CTRL__ACT_FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI5_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__AFI5_REF_CTRL__FREQMHZ {667} \
CONFIG.PSU__CRF_APB__AFI5_REF_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__AFI5_REF__ENABLE {0} \
CONFIG.PSU__CRF_APB__APLL_CTRL__DIV2 {1} \
CONFIG.PSU__CRF_APB__APLL_CTRL__FBDIV {72} \
CONFIG.PSU__CRF_APB__APLL_CTRL__FRACDATA {0} \
CONFIG.PSU__CRF_APB__APLL_CTRL__FRACFREQ {27.138} \
CONFIG.PSU__CRF_APB__APLL_CTRL__SRCSEL {PSS_REF_CLK} \
CONFIG.PSU__CRF_APB__APLL_FRAC_CFG__ENABLED {0} \
CONFIG.PSU__CRF_APB__APLL_TO_LPD_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRF_APB__APM_CTRL__ACT_FREQMHZ {1} \
CONFIG.PSU__CRF_APB__APM_CTRL__DIVISOR0 {1} \
CONFIG.PSU__CRF_APB__APM_CTRL__FREQMHZ {1} \
CONFIG.PSU__CRF_APB__DBG_FPD_CTRL__ACT_FREQMHZ {250.000000} \
CONFIG.PSU__CRF_APB__DBG_FPD_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__DBG_FPD_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRF_APB__DBG_FPD_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__DBG_TRACE_CTRL__ACT_FREQMHZ {250} \
CONFIG.PSU__CRF_APB__DBG_TRACE_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__DBG_TRACE_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRF_APB__DBG_TRACE_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__DBG_TSTMP_CTRL__ACT_FREQMHZ {250.000000} \
CONFIG.PSU__CRF_APB__DBG_TSTMP_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__DBG_TSTMP_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRF_APB__DBG_TSTMP_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__DDR_CTRL__ACT_FREQMHZ {266.666656} \
CONFIG.PSU__CRF_APB__DDR_CTRL__DIVISOR0 {4} \
CONFIG.PSU__CRF_APB__DDR_CTRL__FREQMHZ {533} \
CONFIG.PSU__CRF_APB__DDR_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__DPDMA_REF_CTRL__ACT_FREQMHZ {600.000000} \
CONFIG.PSU__CRF_APB__DPDMA_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__DPDMA_REF_CTRL__FREQMHZ {600} \
CONFIG.PSU__CRF_APB__DPDMA_REF_CTRL__SRCSEL {APLL} \
CONFIG.PSU__CRF_APB__DPLL_CTRL__DIV2 {1} \
CONFIG.PSU__CRF_APB__DPLL_CTRL__FBDIV {64} \
CONFIG.PSU__CRF_APB__DPLL_CTRL__FRACDATA {0} \
CONFIG.PSU__CRF_APB__DPLL_CTRL__FRACFREQ {27.138} \
CONFIG.PSU__CRF_APB__DPLL_CTRL__SRCSEL {PSS_REF_CLK} \
CONFIG.PSU__CRF_APB__DPLL_FRAC_CFG__ENABLED {0} \
CONFIG.PSU__CRF_APB__DPLL_TO_LPD_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRF_APB__DP_AUDIO_REF_CTRL__ACT_FREQMHZ {24.576040} \
CONFIG.PSU__CRF_APB__DP_AUDIO_REF_CTRL__DIVISOR0 {16} \
CONFIG.PSU__CRF_APB__DP_AUDIO_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRF_APB__DP_AUDIO_REF_CTRL__FREQMHZ {25} \
CONFIG.PSU__CRF_APB__DP_AUDIO_REF_CTRL__SRCSEL {RPLL} \
CONFIG.PSU__CRF_APB__DP_AUDIO__FRAC_ENABLED {1} \
CONFIG.PSU__CRF_APB__DP_STC_REF_CTRL__ACT_FREQMHZ {26.214443} \
CONFIG.PSU__CRF_APB__DP_STC_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRF_APB__DP_STC_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRF_APB__DP_STC_REF_CTRL__FREQMHZ {27} \
CONFIG.PSU__CRF_APB__DP_STC_REF_CTRL__SRCSEL {RPLL} \
CONFIG.PSU__CRF_APB__DP_VIDEO_REF_CTRL__ACT_FREQMHZ {297.029572} \
CONFIG.PSU__CRF_APB__DP_VIDEO_REF_CTRL__DIVISOR0 {4} \
CONFIG.PSU__CRF_APB__DP_VIDEO_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRF_APB__DP_VIDEO_REF_CTRL__FREQMHZ {300} \
CONFIG.PSU__CRF_APB__DP_VIDEO_REF_CTRL__SRCSEL {VPLL} \
CONFIG.PSU__CRF_APB__DP_VIDEO__FRAC_ENABLED {1} \
CONFIG.PSU__CRF_APB__GDMA_REF_CTRL__ACT_FREQMHZ {600.000000} \
CONFIG.PSU__CRF_APB__GDMA_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__GDMA_REF_CTRL__FREQMHZ {600} \
CONFIG.PSU__CRF_APB__GDMA_REF_CTRL__SRCSEL {APLL} \
CONFIG.PSU__CRF_APB__GPU_REF_CTRL__ACT_FREQMHZ {500.000000} \
CONFIG.PSU__CRF_APB__GPU_REF_CTRL__DIVISOR0 {1} \
CONFIG.PSU__CRF_APB__GPU_REF_CTRL__FREQMHZ {600} \
CONFIG.PSU__CRF_APB__GPU_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__GTGREF0_REF_CTRL__ACT_FREQMHZ {-1} \
CONFIG.PSU__CRF_APB__GTGREF0_REF_CTRL__DIVISOR0 {-1} \
CONFIG.PSU__CRF_APB__GTGREF0_REF_CTRL__FREQMHZ {-1} \
CONFIG.PSU__CRF_APB__GTGREF0_REF_CTRL__SRCSEL {NA} \
CONFIG.PSU__CRF_APB__GTGREF0__ENABLE {NA} \
CONFIG.PSU__CRF_APB__PCIE_REF_CTRL__ACT_FREQMHZ {250} \
CONFIG.PSU__CRF_APB__PCIE_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__PCIE_REF_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRF_APB__PCIE_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__SATA_REF_CTRL__ACT_FREQMHZ {250} \
CONFIG.PSU__CRF_APB__SATA_REF_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__SATA_REF_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRF_APB__SATA_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__TOPSW_LSBUS_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRF_APB__TOPSW_LSBUS_CTRL__DIVISOR0 {5} \
CONFIG.PSU__CRF_APB__TOPSW_LSBUS_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRF_APB__TOPSW_LSBUS_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRF_APB__TOPSW_MAIN_CTRL__ACT_FREQMHZ {533.333313} \
CONFIG.PSU__CRF_APB__TOPSW_MAIN_CTRL__DIVISOR0 {2} \
CONFIG.PSU__CRF_APB__TOPSW_MAIN_CTRL__FREQMHZ {533.333} \
CONFIG.PSU__CRF_APB__TOPSW_MAIN_CTRL__SRCSEL {DPLL} \
CONFIG.PSU__CRF_APB__VPLL_CTRL__DIV2 {1} \
CONFIG.PSU__CRF_APB__VPLL_CTRL__FBDIV {71} \
CONFIG.PSU__CRF_APB__VPLL_CTRL__FRACDATA {0.2871} \
CONFIG.PSU__CRF_APB__VPLL_CTRL__FRACFREQ {300} \
CONFIG.PSU__CRF_APB__VPLL_CTRL__SRCSEL {PSS_REF_CLK} \
CONFIG.PSU__CRF_APB__VPLL_FRAC_CFG__ENABLED {1} \
CONFIG.PSU__CRF_APB__VPLL_TO_LPD_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__ADMA_REF_CTRL__ACT_FREQMHZ {500.000000} \
CONFIG.PSU__CRL_APB__ADMA_REF_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__ADMA_REF_CTRL__FREQMHZ {500} \
CONFIG.PSU__CRL_APB__ADMA_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__AFI6_REF_CTRL__ACT_FREQMHZ {500} \
CONFIG.PSU__CRL_APB__AFI6_REF_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__AFI6_REF_CTRL__FREQMHZ {500} \
CONFIG.PSU__CRL_APB__AFI6_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__AFI6__ENABLE {0} \
CONFIG.PSU__CRL_APB__AMS_REF_CTRL__ACT_FREQMHZ {51.724136} \
CONFIG.PSU__CRL_APB__AMS_REF_CTRL__DIVISOR0 {29} \
CONFIG.PSU__CRL_APB__AMS_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__AMS_REF_CTRL__FREQMHZ {50} \
CONFIG.PSU__CRL_APB__AMS_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__CAN0_REF_CTRL__ACT_FREQMHZ {100} \
CONFIG.PSU__CRL_APB__CAN0_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__CAN0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__CAN0_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__CAN0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__CAN1_REF_CTRL__ACT_FREQMHZ {100} \
CONFIG.PSU__CRL_APB__CAN1_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__CAN1_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__CAN1_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__CAN1_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__CPU_R5_CTRL__ACT_FREQMHZ {500.000000} \
CONFIG.PSU__CRL_APB__CPU_R5_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__CPU_R5_CTRL__FREQMHZ {500} \
CONFIG.PSU__CRL_APB__CPU_R5_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__CSU_PLL_CTRL__ACT_FREQMHZ {500} \
CONFIG.PSU__CRL_APB__CSU_PLL_CTRL__DIVISOR0 {4} \
CONFIG.PSU__CRL_APB__CSU_PLL_CTRL__FREQMHZ {400} \
CONFIG.PSU__CRL_APB__CSU_PLL_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__DBG_LPD_CTRL__ACT_FREQMHZ {250.000000} \
CONFIG.PSU__CRL_APB__DBG_LPD_CTRL__DIVISOR0 {6} \
CONFIG.PSU__CRL_APB__DBG_LPD_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRL_APB__DBG_LPD_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__DEBUG_R5_ATCLK_CTRL__ACT_FREQMHZ {1000} \
CONFIG.PSU__CRL_APB__DEBUG_R5_ATCLK_CTRL__DIVISOR0 {6} \
CONFIG.PSU__CRL_APB__DEBUG_R5_ATCLK_CTRL__FREQMHZ {1000} \
CONFIG.PSU__CRL_APB__DEBUG_R5_ATCLK_CTRL__SRCSEL {RPLL} \
CONFIG.PSU__CRL_APB__DLL_REF_CTRL__ACT_FREQMHZ {1500.000000} \
CONFIG.PSU__CRL_APB__DLL_REF_CTRL__FREQMHZ {1500} \
CONFIG.PSU__CRL_APB__DLL_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__GEM0_REF_CTRL__ACT_FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM0_REF_CTRL__DIVISOR0 {12} \
CONFIG.PSU__CRL_APB__GEM0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__GEM0_REF_CTRL__FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__GEM1_REF_CTRL__ACT_FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM1_REF_CTRL__DIVISOR0 {12} \
CONFIG.PSU__CRL_APB__GEM1_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__GEM1_REF_CTRL__FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM1_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__GEM2_REF_CTRL__ACT_FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM2_REF_CTRL__DIVISOR0 {12} \
CONFIG.PSU__CRL_APB__GEM2_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__GEM2_REF_CTRL__FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM2_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__GEM3_REF_CTRL__ACT_FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM3_REF_CTRL__DIVISOR0 {12} \
CONFIG.PSU__CRL_APB__GEM3_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__GEM3_REF_CTRL__FREQMHZ {125} \
CONFIG.PSU__CRL_APB__GEM3_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__GEM_TSU_REF_CTRL__ACT_FREQMHZ {250} \
CONFIG.PSU__CRL_APB__GEM_TSU_REF_CTRL__DIVISOR0 {6} \
CONFIG.PSU__CRL_APB__GEM_TSU_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__GEM_TSU_REF_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRL_APB__GEM_TSU_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__I2C0_REF_CTRL__ACT_FREQMHZ {100} \
CONFIG.PSU__CRL_APB__I2C0_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__I2C0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__I2C0_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__I2C0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__I2C1_REF_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRL_APB__I2C1_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__I2C1_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__I2C1_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__I2C1_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__IOPLL_CTRL__DIV2 {0} \
CONFIG.PSU__CRL_APB__IOPLL_CTRL__FBDIV {45} \
CONFIG.PSU__CRL_APB__IOPLL_CTRL__FRACDATA {0} \
CONFIG.PSU__CRL_APB__IOPLL_CTRL__FRACFREQ {27.138} \
CONFIG.PSU__CRL_APB__IOPLL_CTRL__SRCSEL {PSS_REF_CLK} \
CONFIG.PSU__CRL_APB__IOPLL_FRAC_CFG__ENABLED {0} \
CONFIG.PSU__CRL_APB__IOPLL_TO_FPD_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__IOU_SWITCH_CTRL__ACT_FREQMHZ {250.000000} \
CONFIG.PSU__CRL_APB__IOU_SWITCH_CTRL__DIVISOR0 {6} \
CONFIG.PSU__CRL_APB__IOU_SWITCH_CTRL__FREQMHZ {267} \
CONFIG.PSU__CRL_APB__IOU_SWITCH_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__LPD_LSBUS_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRL_APB__LPD_LSBUS_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__LPD_LSBUS_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__LPD_LSBUS_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__LPD_SWITCH_CTRL__ACT_FREQMHZ {500.000000} \
CONFIG.PSU__CRL_APB__LPD_SWITCH_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__LPD_SWITCH_CTRL__FREQMHZ {500} \
CONFIG.PSU__CRL_APB__LPD_SWITCH_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__NAND_REF_CTRL__ACT_FREQMHZ {100} \
CONFIG.PSU__CRL_APB__NAND_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__NAND_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__NAND_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__NAND_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__OCM_MAIN_CTRL__ACT_FREQMHZ {500} \
CONFIG.PSU__CRL_APB__OCM_MAIN_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__OCM_MAIN_CTRL__FREQMHZ {500} \
CONFIG.PSU__CRL_APB__OCM_MAIN_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__PCAP_CTRL__ACT_FREQMHZ {187.500000} \
CONFIG.PSU__CRL_APB__PCAP_CTRL__DIVISOR0 {8} \
CONFIG.PSU__CRL_APB__PCAP_CTRL__FREQMHZ {200} \
CONFIG.PSU__CRL_APB__PCAP_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__PL0_REF_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRL_APB__PL0_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__PL0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__PL0_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__PL0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__PL1_REF_CTRL__ACT_FREQMHZ {24.999975} \
CONFIG.PSU__CRL_APB__PL1_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__PL1_REF_CTRL__DIVISOR1 {4} \
CONFIG.PSU__CRL_APB__PL1_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__PL1_REF_CTRL__SRCSEL {RPLL} \
CONFIG.PSU__CRL_APB__PL2_REF_CTRL__ACT_FREQMHZ {299.999700} \
CONFIG.PSU__CRL_APB__PL2_REF_CTRL__DIVISOR0 {5} \
CONFIG.PSU__CRL_APB__PL2_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__PL2_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__PL2_REF_CTRL__SRCSEL {RPLL} \
CONFIG.PSU__CRL_APB__PL3_REF_CTRL__ACT_FREQMHZ {374.999625} \
CONFIG.PSU__CRL_APB__PL3_REF_CTRL__DIVISOR0 {4} \
CONFIG.PSU__CRL_APB__PL3_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__PL3_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__PL3_REF_CTRL__SRCSEL {RPLL} \
CONFIG.PSU__CRL_APB__QSPI_REF_CTRL__ACT_FREQMHZ {300} \
CONFIG.PSU__CRL_APB__QSPI_REF_CTRL__DIVISOR0 {12} \
CONFIG.PSU__CRL_APB__QSPI_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__QSPI_REF_CTRL__FREQMHZ {300} \
CONFIG.PSU__CRL_APB__QSPI_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__RPLL_CTRL__DIV2 {1} \
CONFIG.PSU__CRL_APB__RPLL_CTRL__FBDIV {70} \
CONFIG.PSU__CRL_APB__RPLL_CTRL__FRACDATA {0.779} \
CONFIG.PSU__CRL_APB__RPLL_CTRL__FRACFREQ {25} \
CONFIG.PSU__CRL_APB__RPLL_CTRL__SRCSEL {PSS_REF_CLK} \
CONFIG.PSU__CRL_APB__RPLL_FRAC_CFG__ENABLED {1} \
CONFIG.PSU__CRL_APB__RPLL_TO_FPD_CTRL__DIVISOR0 {3} \
CONFIG.PSU__CRL_APB__SDIO0_REF_CTRL__ACT_FREQMHZ {187.500000} \
CONFIG.PSU__CRL_APB__SDIO0_REF_CTRL__DIVISOR0 {8} \
CONFIG.PSU__CRL_APB__SDIO0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__SDIO0_REF_CTRL__FREQMHZ {200} \
CONFIG.PSU__CRL_APB__SDIO0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__SDIO1_REF_CTRL__ACT_FREQMHZ {187.500000} \
CONFIG.PSU__CRL_APB__SDIO1_REF_CTRL__DIVISOR0 {8} \
CONFIG.PSU__CRL_APB__SDIO1_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__SDIO1_REF_CTRL__FREQMHZ {200} \
CONFIG.PSU__CRL_APB__SDIO1_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__SPI0_REF_CTRL__ACT_FREQMHZ {187.500000} \
CONFIG.PSU__CRL_APB__SPI0_REF_CTRL__DIVISOR0 {8} \
CONFIG.PSU__CRL_APB__SPI0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__SPI0_REF_CTRL__FREQMHZ {200} \
CONFIG.PSU__CRL_APB__SPI0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__SPI1_REF_CTRL__ACT_FREQMHZ {187.500000} \
CONFIG.PSU__CRL_APB__SPI1_REF_CTRL__DIVISOR0 {8} \
CONFIG.PSU__CRL_APB__SPI1_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__SPI1_REF_CTRL__FREQMHZ {200} \
CONFIG.PSU__CRL_APB__SPI1_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__TIMESTAMP_REF_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRL_APB__TIMESTAMP_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__TIMESTAMP_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__TIMESTAMP_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__UART0_REF_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRL_APB__UART0_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__UART0_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__UART0_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__UART0_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__UART1_REF_CTRL__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__CRL_APB__UART1_REF_CTRL__DIVISOR0 {15} \
CONFIG.PSU__CRL_APB__UART1_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__UART1_REF_CTRL__FREQMHZ {100} \
CONFIG.PSU__CRL_APB__UART1_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__USB0_BUS_REF_CTRL__ACT_FREQMHZ {250.000000} \
CONFIG.PSU__CRL_APB__USB0_BUS_REF_CTRL__DIVISOR0 {6} \
CONFIG.PSU__CRL_APB__USB0_BUS_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__USB0_BUS_REF_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRL_APB__USB0_BUS_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__USB1_BUS_REF_CTRL__ACT_FREQMHZ {250.000000} \
CONFIG.PSU__CRL_APB__USB1_BUS_REF_CTRL__DIVISOR0 {6} \
CONFIG.PSU__CRL_APB__USB1_BUS_REF_CTRL__DIVISOR1 {1} \
CONFIG.PSU__CRL_APB__USB1_BUS_REF_CTRL__FREQMHZ {250} \
CONFIG.PSU__CRL_APB__USB1_BUS_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__USB3_DUAL_REF_CTRL__ACT_FREQMHZ {20.000000} \
CONFIG.PSU__CRL_APB__USB3_DUAL_REF_CTRL__DIVISOR0 {5} \
CONFIG.PSU__CRL_APB__USB3_DUAL_REF_CTRL__DIVISOR1 {15} \
CONFIG.PSU__CRL_APB__USB3_DUAL_REF_CTRL__FREQMHZ {20} \
CONFIG.PSU__CRL_APB__USB3_DUAL_REF_CTRL__SRCSEL {IOPLL} \
CONFIG.PSU__CRL_APB__USB3__ENABLE {1} \
CONFIG.PSU__CSUPMU__PERIPHERAL__VALID {1} \
CONFIG.PSU__CSU_COHERENCY {0} \
CONFIG.PSU__CSU__CSU_TAMPER_0__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_0__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_10__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_10__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_11__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_11__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_12__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_12__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_1__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_1__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_2__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_2__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_3__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_3__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_4__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_4__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_5__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_5__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_6__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_6__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_7__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_7__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_8__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_8__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__CSU_TAMPER_9__ENABLE {0} \
CONFIG.PSU__CSU__CSU_TAMPER_9__ERASE_BBRAM {0} \
CONFIG.PSU__CSU__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__DDRC__ADDR_MIRROR {1} \
CONFIG.PSU__DDRC__AL {0} \
CONFIG.PSU__DDRC__BANK_ADDR_COUNT {3} \
CONFIG.PSU__DDRC__BG_ADDR_COUNT {NA} \
CONFIG.PSU__DDRC__BRC_MAPPING {ROW_BANK_COL} \
CONFIG.PSU__DDRC__BUS_WIDTH {32 Bit} \
CONFIG.PSU__DDRC__CL {NA} \
CONFIG.PSU__DDRC__CLOCK_STOP_EN {0} \
CONFIG.PSU__DDRC__COL_ADDR_COUNT {10} \
CONFIG.PSU__DDRC__COMPONENTS {Components} \
CONFIG.PSU__DDRC__CWL {NA} \
CONFIG.PSU__DDRC__DDR3L_T_REF_RANGE {NA} \
CONFIG.PSU__DDRC__DDR3_T_REF_RANGE {NA} \
CONFIG.PSU__DDRC__DDR4_ADDR_MAPPING {NA} \
CONFIG.PSU__DDRC__DDR4_CAL_MODE_ENABLE {NA} \
CONFIG.PSU__DDRC__DDR4_CRC_CONTROL {NA} \
CONFIG.PSU__DDRC__DDR4_MAXPWR_SAVING_EN {NA} \
CONFIG.PSU__DDRC__DDR4_T_REF_MODE {NA} \
CONFIG.PSU__DDRC__DDR4_T_REF_RANGE {NA} \
CONFIG.PSU__DDRC__DEEP_PWR_DOWN_EN {0} \
CONFIG.PSU__DDRC__DEVICE_CAPACITY {8192 MBits} \
CONFIG.PSU__DDRC__DIMM_ADDR_MIRROR {NA} \
CONFIG.PSU__DDRC__DM_DBI {DM_NO_DBI} \
CONFIG.PSU__DDRC__DQMAP_0_3 {0} \
CONFIG.PSU__DDRC__DQMAP_12_15 {0} \
CONFIG.PSU__DDRC__DQMAP_16_19 {0} \
CONFIG.PSU__DDRC__DQMAP_20_23 {0} \
CONFIG.PSU__DDRC__DQMAP_24_27 {0} \
CONFIG.PSU__DDRC__DQMAP_28_31 {0} \
CONFIG.PSU__DDRC__DQMAP_32_35 {0} \
CONFIG.PSU__DDRC__DQMAP_36_39 {0} \
CONFIG.PSU__DDRC__DQMAP_40_43 {0} \
CONFIG.PSU__DDRC__DQMAP_44_47 {0} \
CONFIG.PSU__DDRC__DQMAP_48_51 {0} \
CONFIG.PSU__DDRC__DQMAP_4_7 {0} \
CONFIG.PSU__DDRC__DQMAP_52_55 {0} \
CONFIG.PSU__DDRC__DQMAP_56_59 {0} \
CONFIG.PSU__DDRC__DQMAP_60_63 {0} \
CONFIG.PSU__DDRC__DQMAP_64_67 {0} \
CONFIG.PSU__DDRC__DQMAP_68_71 {0} \
CONFIG.PSU__DDRC__DQMAP_8_11 {0} \
CONFIG.PSU__DDRC__DRAM_WIDTH {32 Bits} \
CONFIG.PSU__DDRC__ECC {Disabled} \
CONFIG.PSU__DDRC__ECC_SCRUB {0} \
CONFIG.PSU__DDRC__ENABLE {1} \
CONFIG.PSU__DDRC__ENABLE_2T_TIMING {0} \
CONFIG.PSU__DDRC__ENABLE_DP_SWITCH {1} \
CONFIG.PSU__DDRC__ENABLE_LP4_HAS_ECC_COMP {0} \
CONFIG.PSU__DDRC__ENABLE_LP4_SLOWBOOT {0} \
CONFIG.PSU__DDRC__EN_2ND_CLK {0} \
CONFIG.PSU__DDRC__FGRM {NA} \
CONFIG.PSU__DDRC__FREQ_MHZ {1} \
CONFIG.PSU__DDRC__LPDDR3_DUALRANK_SDP {0} \
CONFIG.PSU__DDRC__LPDDR3_T_REF_RANGE {NA} \
CONFIG.PSU__DDRC__LPDDR4_T_REF_RANGE {Normal (0-85)} \
CONFIG.PSU__DDRC__LP_ASR {NA} \
CONFIG.PSU__DDRC__MEMORY_TYPE {LPDDR 4} \
CONFIG.PSU__DDRC__PARITY_ENABLE {NA} \
CONFIG.PSU__DDRC__PER_BANK_REFRESH {0} \
CONFIG.PSU__DDRC__PHY_DBI_MODE {0} \
CONFIG.PSU__DDRC__PLL_BYPASS {0} \
CONFIG.PSU__DDRC__PWR_DOWN_EN {0} \
CONFIG.PSU__DDRC__RANK_ADDR_COUNT {1} \
CONFIG.PSU__DDRC__RD_DQS_CENTER {0} \
CONFIG.PSU__DDRC__ROW_ADDR_COUNT {15} \
CONFIG.PSU__DDRC__SB_TARGET {NA} \
CONFIG.PSU__DDRC__SELF_REF_ABORT {NA} \
CONFIG.PSU__DDRC__SPEED_BIN {LPDDR4_1066} \
CONFIG.PSU__DDRC__STATIC_RD_MODE {0} \
CONFIG.PSU__DDRC__TRAIN_DATA_EYE {1} \
CONFIG.PSU__DDRC__TRAIN_READ_GATE {1} \
CONFIG.PSU__DDRC__TRAIN_WRITE_LEVEL {1} \
CONFIG.PSU__DDRC__T_FAW {40.0} \
CONFIG.PSU__DDRC__T_RAS_MIN {42} \
CONFIG.PSU__DDRC__T_RC {63} \
CONFIG.PSU__DDRC__T_RCD {10} \
CONFIG.PSU__DDRC__T_RP {12} \
CONFIG.PSU__DDRC__VENDOR_PART {OTHERS} \
CONFIG.PSU__DDRC__VIDEO_BUFFER_SIZE {0} \
CONFIG.PSU__DDRC__VREF {0} \
CONFIG.PSU__DDR_HIGH_ADDRESS_GUI_ENABLE {0} \
CONFIG.PSU__DDR_QOS_ENABLE {1} \
CONFIG.PSU__DDR_QOS_FIX_HP0_RDQOS {7} \
CONFIG.PSU__DDR_QOS_FIX_HP0_WRQOS {15} \
CONFIG.PSU__DDR_QOS_FIX_HP1_RDQOS {3} \
CONFIG.PSU__DDR_QOS_FIX_HP1_WRQOS {3} \
CONFIG.PSU__DDR_QOS_FIX_HP2_RDQOS {3} \
CONFIG.PSU__DDR_QOS_FIX_HP2_WRQOS {3} \
CONFIG.PSU__DDR_QOS_FIX_HP3_RDQOS {3} \
CONFIG.PSU__DDR_QOS_FIX_HP3_WRQOS {3} \
CONFIG.PSU__DDR_QOS_HP0_RDQOS {7} \
CONFIG.PSU__DDR_QOS_HP0_WRQOS {15} \
CONFIG.PSU__DDR_QOS_HP1_RDQOS {3} \
CONFIG.PSU__DDR_QOS_HP1_WRQOS {3} \
CONFIG.PSU__DDR_QOS_HP2_RDQOS {3} \
CONFIG.PSU__DDR_QOS_HP2_WRQOS {3} \
CONFIG.PSU__DDR_QOS_HP3_RDQOS {3} \
CONFIG.PSU__DDR_QOS_HP3_WRQOS {3} \
CONFIG.PSU__DDR_QOS_PORT0_TYPE {Low Latency} \
CONFIG.PSU__DDR_QOS_PORT1_VN1_TYPE {Low Latency} \
CONFIG.PSU__DDR_QOS_PORT1_VN2_TYPE {Best Effort} \
CONFIG.PSU__DDR_QOS_PORT2_VN1_TYPE {Low Latency} \
CONFIG.PSU__DDR_QOS_PORT2_VN2_TYPE {Best Effort} \
CONFIG.PSU__DDR_QOS_PORT3_TYPE {Video Traffic} \
CONFIG.PSU__DDR_QOS_PORT4_TYPE {Best Effort} \
CONFIG.PSU__DDR_QOS_PORT5_TYPE {Best Effort} \
CONFIG.PSU__DDR_QOS_RD_HPR_THRSHLD {0} \
CONFIG.PSU__DDR_QOS_RD_LPR_THRSHLD {16} \
CONFIG.PSU__DDR_QOS_WR_THRSHLD {16} \
CONFIG.PSU__DDR_SW_REFRESH_ENABLED {1} \
CONFIG.PSU__DDR__INTERFACE__FREQMHZ {266.500} \
CONFIG.PSU__DEVICE_TYPE {EG} \
CONFIG.PSU__DISPLAYPORT__LANE0__ENABLE {1} \
CONFIG.PSU__DISPLAYPORT__LANE0__IO {GT Lane1} \
CONFIG.PSU__DISPLAYPORT__LANE1__ENABLE {1} \
CONFIG.PSU__DISPLAYPORT__LANE1__IO {GT Lane0} \
CONFIG.PSU__DISPLAYPORT__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__DLL__ISUSED {1} \
CONFIG.PSU__DPAUX__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__DPAUX__PERIPHERAL__IO {MIO 27 .. 30} \
CONFIG.PSU__DP__LANE_SEL {Dual Lower} \
CONFIG.PSU__DP__REF_CLK_FREQ {27} \
CONFIG.PSU__DP__REF_CLK_SEL {Ref Clk1} \
CONFIG.PSU__ENABLE__DDR__REFRESH__SIGNALS {0} \
CONFIG.PSU__ENET0__FIFO__ENABLE {0} \
CONFIG.PSU__ENET0__GRP_MDIO__ENABLE {0} \
CONFIG.PSU__ENET0__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__ENET0__PTP__ENABLE {0} \
CONFIG.PSU__ENET0__TSU__ENABLE {0} \
CONFIG.PSU__ENET1__FIFO__ENABLE {0} \
CONFIG.PSU__ENET1__GRP_MDIO__ENABLE {0} \
CONFIG.PSU__ENET1__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__ENET1__PTP__ENABLE {0} \
CONFIG.PSU__ENET1__TSU__ENABLE {0} \
CONFIG.PSU__ENET2__FIFO__ENABLE {0} \
CONFIG.PSU__ENET2__GRP_MDIO__ENABLE {0} \
CONFIG.PSU__ENET2__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__ENET2__PTP__ENABLE {0} \
CONFIG.PSU__ENET2__TSU__ENABLE {0} \
CONFIG.PSU__ENET3__FIFO__ENABLE {0} \
CONFIG.PSU__ENET3__GRP_MDIO__ENABLE {0} \
CONFIG.PSU__ENET3__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__ENET3__PTP__ENABLE {0} \
CONFIG.PSU__ENET3__TSU__ENABLE {0} \
CONFIG.PSU__EN_AXI_STATUS_PORTS {0} \
CONFIG.PSU__EN_EMIO_TRACE {0} \
CONFIG.PSU__EP__IP {0} \
CONFIG.PSU__EXPAND__CORESIGHT {0} \
CONFIG.PSU__EXPAND__FPD_SLAVES {0} \
CONFIG.PSU__EXPAND__GIC {0} \
CONFIG.PSU__EXPAND__LOWER_LPS_SLAVES {0} \
CONFIG.PSU__EXPAND__UPPER_LPS_SLAVES {0} \
CONFIG.PSU__FPDMASTERS_COHERENCY {0} \
CONFIG.PSU__FPD_SLCR__WDT1__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__FPD_SLCR__WDT1__FREQMHZ {100.000000} \
CONFIG.PSU__FPD_SLCR__WDT_CLK_SEL__SELECT {APB} \
CONFIG.PSU__FPGA_PL0_ENABLE {1} \
CONFIG.PSU__FPGA_PL1_ENABLE {0} \
CONFIG.PSU__FPGA_PL2_ENABLE {0} \
CONFIG.PSU__FPGA_PL3_ENABLE {0} \
CONFIG.PSU__FP__POWER__ON {1} \
CONFIG.PSU__FTM__CTI_IN_0 {0} \
CONFIG.PSU__FTM__CTI_IN_1 {0} \
CONFIG.PSU__FTM__CTI_IN_2 {0} \
CONFIG.PSU__FTM__CTI_IN_3 {0} \
CONFIG.PSU__FTM__CTI_OUT_0 {0} \
CONFIG.PSU__FTM__CTI_OUT_1 {0} \
CONFIG.PSU__FTM__CTI_OUT_2 {0} \
CONFIG.PSU__FTM__CTI_OUT_3 {0} \
CONFIG.PSU__FTM__GPI {0} \
CONFIG.PSU__FTM__GPO {0} \
CONFIG.PSU__GEM0_COHERENCY {0} \
CONFIG.PSU__GEM0_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__GEM1_COHERENCY {0} \
CONFIG.PSU__GEM1_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__GEM2_COHERENCY {0} \
CONFIG.PSU__GEM2_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__GEM3_COHERENCY {0} \
CONFIG.PSU__GEM3_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__GEM__TSU__ENABLE {0} \
CONFIG.PSU__GEN_IPI_0__MASTER {APU} \
CONFIG.PSU__GEN_IPI_10__MASTER {NONE} \
CONFIG.PSU__GEN_IPI_1__MASTER {RPU0} \
CONFIG.PSU__GEN_IPI_2__MASTER {RPU1} \
CONFIG.PSU__GEN_IPI_3__MASTER {PMU} \
CONFIG.PSU__GEN_IPI_4__MASTER {PMU} \
CONFIG.PSU__GEN_IPI_5__MASTER {PMU} \
CONFIG.PSU__GEN_IPI_6__MASTER {PMU} \
CONFIG.PSU__GEN_IPI_7__MASTER {NONE} \
CONFIG.PSU__GEN_IPI_8__MASTER {NONE} \
CONFIG.PSU__GEN_IPI_9__MASTER {NONE} \
CONFIG.PSU__GPIO0_MIO__IO {MIO 0 .. 25} \
CONFIG.PSU__GPIO0_MIO__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__GPIO1_MIO__IO {MIO 26 .. 51} \
CONFIG.PSU__GPIO1_MIO__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__GPIO2_MIO__IO {MIO 52 .. 77} \
CONFIG.PSU__GPIO2_MIO__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__GPIO_EMIO_WIDTH {1} \
CONFIG.PSU__GPIO_EMIO__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__GPIO_EMIO__PERIPHERAL__IO {<Select>} \
CONFIG.PSU__GPIO_EMIO__WIDTH {[94:0]} \
CONFIG.PSU__GPU_PP0__POWER__ON {1} \
CONFIG.PSU__GPU_PP1__POWER__ON {1} \
CONFIG.PSU__GT_REF_CLK__FREQMHZ {33.333} \
CONFIG.PSU__GT__LINK_SPEED {HBR} \
CONFIG.PSU__GT__PRE_EMPH_LVL_4 {0} \
CONFIG.PSU__GT__VLT_SWNG_LVL_4 {0} \
CONFIG.PSU__HIGH_ADDRESS__ENABLE {0} \
CONFIG.PSU__HPM0_FPD__NUM_READ_THREADS {4} \
CONFIG.PSU__HPM0_FPD__NUM_WRITE_THREADS {4} \
CONFIG.PSU__HPM0_LPD__NUM_READ_THREADS {4} \
CONFIG.PSU__HPM0_LPD__NUM_WRITE_THREADS {4} \
CONFIG.PSU__HPM1_FPD__NUM_READ_THREADS {4} \
CONFIG.PSU__HPM1_FPD__NUM_WRITE_THREADS {4} \
CONFIG.PSU__I2C0_LOOP_I2C1__ENABLE {0} \
CONFIG.PSU__I2C0__GRP_INT__ENABLE {0} \
CONFIG.PSU__I2C0__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__I2C1__GRP_INT__ENABLE {0} \
CONFIG.PSU__I2C1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__I2C1__PERIPHERAL__IO {MIO 4 .. 5} \
CONFIG.PSU__IOU_SLCR__IOU_TTC_APB_CLK__TTC0_SEL {APB} \
CONFIG.PSU__IOU_SLCR__IOU_TTC_APB_CLK__TTC1_SEL {APB} \
CONFIG.PSU__IOU_SLCR__IOU_TTC_APB_CLK__TTC2_SEL {APB} \
CONFIG.PSU__IOU_SLCR__IOU_TTC_APB_CLK__TTC3_SEL {APB} \
CONFIG.PSU__IOU_SLCR__TTC0__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC0__FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC1__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC1__FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC2__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC2__FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC3__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__TTC3__FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__WDT0__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__WDT0__FREQMHZ {100.000000} \
CONFIG.PSU__IOU_SLCR__WDT_CLK_SEL__SELECT {APB} \
CONFIG.PSU__IRQ_P2F_ADMA_CHAN__INT {0} \
CONFIG.PSU__IRQ_P2F_AIB_AXI__INT {0} \
CONFIG.PSU__IRQ_P2F_AMS__INT {0} \
CONFIG.PSU__IRQ_P2F_APM_FPD__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_COMM__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_CPUMNT__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_CTI__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_EXTERR__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_IPI__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_L2ERR__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_PMU__INT {0} \
CONFIG.PSU__IRQ_P2F_APU_REGS__INT {0} \
CONFIG.PSU__IRQ_P2F_ATB_LPD__INT {0} \
CONFIG.PSU__IRQ_P2F_CAN0__INT {0} \
CONFIG.PSU__IRQ_P2F_CAN1__INT {0} \
CONFIG.PSU__IRQ_P2F_CLKMON__INT {0} \
CONFIG.PSU__IRQ_P2F_CSUPMU_WDT__INT {0} \
CONFIG.PSU__IRQ_P2F_CSU_DMA__INT {0} \
CONFIG.PSU__IRQ_P2F_CSU__INT {0} \
CONFIG.PSU__IRQ_P2F_DDR_SS__INT {0} \
CONFIG.PSU__IRQ_P2F_DPDMA__INT {0} \
CONFIG.PSU__IRQ_P2F_DPORT__INT {0} \
CONFIG.PSU__IRQ_P2F_EFUSE__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT0_WAKEUP__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT0__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT1_WAKEUP__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT1__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT2_WAKEUP__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT2__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT3_WAKEUP__INT {0} \
CONFIG.PSU__IRQ_P2F_ENT3__INT {0} \
CONFIG.PSU__IRQ_P2F_FPD_APB__INT {0} \
CONFIG.PSU__IRQ_P2F_FPD_ATB_ERR__INT {0} \
CONFIG.PSU__IRQ_P2F_FP_WDT__INT {0} \
CONFIG.PSU__IRQ_P2F_GDMA_CHAN__INT {0} \
CONFIG.PSU__IRQ_P2F_GPIO__INT {0} \
CONFIG.PSU__IRQ_P2F_GPU__INT {0} \
CONFIG.PSU__IRQ_P2F_I2C0__INT {0} \
CONFIG.PSU__IRQ_P2F_I2C1__INT {0} \
CONFIG.PSU__IRQ_P2F_LPD_APB__INT {0} \
CONFIG.PSU__IRQ_P2F_LPD_APM__INT {0} \
CONFIG.PSU__IRQ_P2F_LP_WDT__INT {0} \
CONFIG.PSU__IRQ_P2F_NAND__INT {0} \
CONFIG.PSU__IRQ_P2F_OCM_ERR__INT {0} \
CONFIG.PSU__IRQ_P2F_PCIE_DMA__INT {0} \
CONFIG.PSU__IRQ_P2F_PCIE_LEGACY__INT {0} \
CONFIG.PSU__IRQ_P2F_PCIE_MSC__INT {0} \
CONFIG.PSU__IRQ_P2F_PCIE_MSI__INT {0} \
CONFIG.PSU__IRQ_P2F_PL_IPI__INT {0} \
CONFIG.PSU__IRQ_P2F_QSPI__INT {0} \
CONFIG.PSU__IRQ_P2F_R5_CORE0_ECC_ERR__INT {0} \
CONFIG.PSU__IRQ_P2F_R5_CORE1_ECC_ERR__INT {0} \
CONFIG.PSU__IRQ_P2F_RPU_IPI__INT {0} \
CONFIG.PSU__IRQ_P2F_RPU_PERMON__INT {0} \
CONFIG.PSU__IRQ_P2F_RTC_ALARM__INT {0} \
CONFIG.PSU__IRQ_P2F_RTC_SECONDS__INT {0} \
CONFIG.PSU__IRQ_P2F_SATA__INT {0} \
CONFIG.PSU__IRQ_P2F_SDIO0_WAKE__INT {0} \
CONFIG.PSU__IRQ_P2F_SDIO0__INT {0} \
CONFIG.PSU__IRQ_P2F_SDIO1_WAKE__INT {0} \
CONFIG.PSU__IRQ_P2F_SDIO1__INT {0} \
CONFIG.PSU__IRQ_P2F_SPI0__INT {0} \
CONFIG.PSU__IRQ_P2F_SPI1__INT {0} \
CONFIG.PSU__IRQ_P2F_TTC0__INT0 {0} \
CONFIG.PSU__IRQ_P2F_TTC0__INT1 {0} \
CONFIG.PSU__IRQ_P2F_TTC0__INT2 {0} \
CONFIG.PSU__IRQ_P2F_TTC1__INT0 {0} \
CONFIG.PSU__IRQ_P2F_TTC1__INT1 {0} \
CONFIG.PSU__IRQ_P2F_TTC1__INT2 {0} \
CONFIG.PSU__IRQ_P2F_TTC2__INT0 {0} \
CONFIG.PSU__IRQ_P2F_TTC2__INT1 {0} \
CONFIG.PSU__IRQ_P2F_TTC2__INT2 {0} \
CONFIG.PSU__IRQ_P2F_TTC3__INT0 {0} \
CONFIG.PSU__IRQ_P2F_TTC3__INT1 {0} \
CONFIG.PSU__IRQ_P2F_TTC3__INT2 {0} \
CONFIG.PSU__IRQ_P2F_UART0__INT {0} \
CONFIG.PSU__IRQ_P2F_UART1__INT {0} \
CONFIG.PSU__IRQ_P2F_USB3_ENDPOINT__INT0 {0} \
CONFIG.PSU__IRQ_P2F_USB3_ENDPOINT__INT1 {0} \
CONFIG.PSU__IRQ_P2F_USB3_OTG__INT0 {0} \
CONFIG.PSU__IRQ_P2F_USB3_OTG__INT1 {0} \
CONFIG.PSU__IRQ_P2F_USB3_PMU_WAKEUP__INT {0} \
CONFIG.PSU__IRQ_P2F_XMPU_FPD__INT {0} \
CONFIG.PSU__IRQ_P2F_XMPU_LPD__INT {0} \
CONFIG.PSU__IRQ_P2F__INTF_FPD_SMMU__INT {0} \
CONFIG.PSU__IRQ_P2F__INTF_PPD_CCI__INT {0} \
CONFIG.PSU__L2_BANK0__POWER__ON {1} \
CONFIG.PSU__LPDMA0_COHERENCY {0} \
CONFIG.PSU__LPDMA1_COHERENCY {0} \
CONFIG.PSU__LPDMA2_COHERENCY {0} \
CONFIG.PSU__LPDMA3_COHERENCY {0} \
CONFIG.PSU__LPDMA4_COHERENCY {0} \
CONFIG.PSU__LPDMA5_COHERENCY {0} \
CONFIG.PSU__LPDMA6_COHERENCY {0} \
CONFIG.PSU__LPDMA7_COHERENCY {0} \
CONFIG.PSU__LPD_SLCR__CSUPMU_WDT_CLK_SEL__SELECT {APB} \
CONFIG.PSU__LPD_SLCR__CSUPMU__ACT_FREQMHZ {100.000000} \
CONFIG.PSU__LPD_SLCR__CSUPMU__FREQMHZ {100.000000} \
CONFIG.PSU__MAXIGP0__DATA_WIDTH {128} \
CONFIG.PSU__MAXIGP1__DATA_WIDTH {128} \
CONFIG.PSU__MAXIGP2__DATA_WIDTH {32} \
CONFIG.PSU__M_AXI_GP0_SUPPORTS_NARROW_BURST {1} \
CONFIG.PSU__M_AXI_GP1_SUPPORTS_NARROW_BURST {1} \
CONFIG.PSU__M_AXI_GP2_SUPPORTS_NARROW_BURST {1} \
CONFIG.PSU__NAND_COHERENCY {0} \
CONFIG.PSU__NAND_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__NAND__CHIP_ENABLE__ENABLE {0} \
CONFIG.PSU__NAND__DATA_STROBE__ENABLE {0} \
CONFIG.PSU__NAND__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__NAND__READY0_BUSY__ENABLE {0} \
CONFIG.PSU__NAND__READY1_BUSY__ENABLE {0} \
CONFIG.PSU__NAND__READY_BUSY__ENABLE {0} \
CONFIG.PSU__NUM_FABRIC_RESETS {1} \
CONFIG.PSU__OCM_BANK0__POWER__ON {1} \
CONFIG.PSU__OCM_BANK1__POWER__ON {1} \
CONFIG.PSU__OCM_BANK2__POWER__ON {1} \
CONFIG.PSU__OCM_BANK3__POWER__ON {1} \
CONFIG.PSU__OVERRIDE_HPX_QOS {0} \
CONFIG.PSU__OVERRIDE__BASIC_CLOCK {1} \
CONFIG.PSU__PCIE__ACS_VIOLAION {0} \
CONFIG.PSU__PCIE__ACS_VIOLATION {0} \
CONFIG.PSU__PCIE__AER_CAPABILITY {0} \
CONFIG.PSU__PCIE__ATOMICOP_EGRESS_BLOCKED {0} \
CONFIG.PSU__PCIE__BAR0_64BIT {0} \
CONFIG.PSU__PCIE__BAR0_ENABLE {0} \
CONFIG.PSU__PCIE__BAR0_PREFETCHABLE {0} \
CONFIG.PSU__PCIE__BAR0_VAL {} \
CONFIG.PSU__PCIE__BAR1_64BIT {0} \
CONFIG.PSU__PCIE__BAR1_ENABLE {0} \
CONFIG.PSU__PCIE__BAR1_PREFETCHABLE {0} \
CONFIG.PSU__PCIE__BAR1_VAL {} \
CONFIG.PSU__PCIE__BAR2_64BIT {0} \
CONFIG.PSU__PCIE__BAR2_ENABLE {0} \
CONFIG.PSU__PCIE__BAR2_PREFETCHABLE {0} \
CONFIG.PSU__PCIE__BAR2_VAL {} \
CONFIG.PSU__PCIE__BAR3_64BIT {0} \
CONFIG.PSU__PCIE__BAR3_ENABLE {0} \
CONFIG.PSU__PCIE__BAR3_PREFETCHABLE {0} \
CONFIG.PSU__PCIE__BAR3_VAL {} \
CONFIG.PSU__PCIE__BAR4_64BIT {0} \
CONFIG.PSU__PCIE__BAR4_ENABLE {0} \
CONFIG.PSU__PCIE__BAR4_PREFETCHABLE {0} \
CONFIG.PSU__PCIE__BAR4_VAL {} \
CONFIG.PSU__PCIE__BAR5_64BIT {0} \
CONFIG.PSU__PCIE__BAR5_ENABLE {0} \
CONFIG.PSU__PCIE__BAR5_PREFETCHABLE {0} \
CONFIG.PSU__PCIE__BAR5_VAL {} \
CONFIG.PSU__PCIE__CLASS_CODE_BASE {} \
CONFIG.PSU__PCIE__CLASS_CODE_INTERFACE {} \
CONFIG.PSU__PCIE__CLASS_CODE_SUB {} \
CONFIG.PSU__PCIE__CLASS_CODE_VALUE {} \
CONFIG.PSU__PCIE__COMPLETER_ABORT {0} \
CONFIG.PSU__PCIE__COMPLTION_TIMEOUT {0} \
CONFIG.PSU__PCIE__CORRECTABLE_INT_ERR {0} \
CONFIG.PSU__PCIE__CRS_SW_VISIBILITY {0} \
CONFIG.PSU__PCIE__DEVICE_ID {} \
CONFIG.PSU__PCIE__ECRC_CHECK {0} \
CONFIG.PSU__PCIE__ECRC_ERR {0} \
CONFIG.PSU__PCIE__ECRC_GEN {0} \
CONFIG.PSU__PCIE__EROM_ENABLE {0} \
CONFIG.PSU__PCIE__EROM_VAL {} \
CONFIG.PSU__PCIE__FLOW_CONTROL_ERR {0} \
CONFIG.PSU__PCIE__FLOW_CONTROL_PROTOCOL_ERR {0} \
CONFIG.PSU__PCIE__HEADER_LOG_OVERFLOW {0} \
CONFIG.PSU__PCIE__INTX_GENERATION {0} \
CONFIG.PSU__PCIE__LANE0__ENABLE {0} \
CONFIG.PSU__PCIE__LANE1__ENABLE {0} \
CONFIG.PSU__PCIE__LANE2__ENABLE {0} \
CONFIG.PSU__PCIE__LANE3__ENABLE {0} \
CONFIG.PSU__PCIE__MC_BLOCKED_TLP {0} \
CONFIG.PSU__PCIE__MSIX_BAR_INDICATOR {} \
CONFIG.PSU__PCIE__MSIX_CAPABILITY {0} \
CONFIG.PSU__PCIE__MSIX_PBA_BAR_INDICATOR {} \
CONFIG.PSU__PCIE__MSIX_PBA_OFFSET {0} \
CONFIG.PSU__PCIE__MSIX_TABLE_OFFSET {0} \
CONFIG.PSU__PCIE__MSIX_TABLE_SIZE {0} \
CONFIG.PSU__PCIE__MSI_64BIT_ADDR_CAPABLE {0} \
CONFIG.PSU__PCIE__MSI_CAPABILITY {0} \
CONFIG.PSU__PCIE__MULTIHEADER {0} \
CONFIG.PSU__PCIE__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__PCIE__PERIPHERAL__ENDPOINT_ENABLE {1} \
CONFIG.PSU__PCIE__PERIPHERAL__ROOTPORT_ENABLE {0} \
CONFIG.PSU__PCIE__PERM_ROOT_ERR_UPDATE {0} \
CONFIG.PSU__PCIE__RECEIVER_ERR {0} \
CONFIG.PSU__PCIE__RECEIVER_OVERFLOW {0} \
CONFIG.PSU__PCIE__RESET__POLARITY {Active Low} \
CONFIG.PSU__PCIE__REVISION_ID {} \
CONFIG.PSU__PCIE__SUBSYSTEM_ID {} \
CONFIG.PSU__PCIE__SUBSYSTEM_VENDOR_ID {} \
CONFIG.PSU__PCIE__SURPRISE_DOWN {0} \
CONFIG.PSU__PCIE__TLP_PREFIX_BLOCKED {0} \
CONFIG.PSU__PCIE__UNCORRECTABL_INT_ERR {0} \
CONFIG.PSU__PCIE__VENDOR_ID {} \
CONFIG.PSU__PJTAG__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__PL_CLK0_BUF {TRUE} \
CONFIG.PSU__PL_CLK1_BUF {FALSE} \
CONFIG.PSU__PL_CLK2_BUF {FALSE} \
CONFIG.PSU__PL_CLK3_BUF {FALSE} \
CONFIG.PSU__PL__POWER__ON {1} \
CONFIG.PSU__PMU_COHERENCY {0} \
CONFIG.PSU__PMU__AIBACK__ENABLE {0} \
CONFIG.PSU__PMU__EMIO_GPI__ENABLE {0} \
CONFIG.PSU__PMU__EMIO_GPO__ENABLE {0} \
CONFIG.PSU__PMU__GPI0__ENABLE {1} \
CONFIG.PSU__PMU__GPI0__IO {MIO 26} \
CONFIG.PSU__PMU__GPI1__ENABLE {0} \
CONFIG.PSU__PMU__GPI2__ENABLE {0} \
CONFIG.PSU__PMU__GPI3__ENABLE {0} \
CONFIG.PSU__PMU__GPI4__ENABLE {0} \
CONFIG.PSU__PMU__GPI5__ENABLE {0} \
CONFIG.PSU__PMU__GPO0__ENABLE {1} \
CONFIG.PSU__PMU__GPO0__IO {MIO 32} \
CONFIG.PSU__PMU__GPO1__ENABLE {1} \
CONFIG.PSU__PMU__GPO1__IO {MIO 33} \
CONFIG.PSU__PMU__GPO2__ENABLE {1} \
CONFIG.PSU__PMU__GPO2__IO {MIO 34} \
CONFIG.PSU__PMU__GPO2__POLARITY {high} \
CONFIG.PSU__PMU__GPO3__ENABLE {0} \
CONFIG.PSU__PMU__GPO4__ENABLE {0} \
CONFIG.PSU__PMU__GPO5__ENABLE {0} \
CONFIG.PSU__PMU__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__PMU__PLERROR__ENABLE {0} \
CONFIG.PSU__PRESET_APPLIED {1} \
CONFIG.PSU__PROTECTION__DDR_SEGMENTS {NONE} \
CONFIG.PSU__PROTECTION__DEBUG {0} \
CONFIG.PSU__PROTECTION__ENABLE {0} \
CONFIG.PSU__PROTECTION__FPD_SEGMENTS {\
SA:0xFD1A0000; SIZE:1280; UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write;\
subsystemId:PMU Firmware | SA:0xFD000000; SIZE:64; UNIT:KB; RegionTZ:Secure;\
WrAllowed:Read/Write; subsystemId:PMU Firmware | SA:0xFD010000; SIZE:64;\
UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write; subsystemId:PMU Firmware | \
SA:0xFD020000; SIZE:64; UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write;\
subsystemId:PMU Firmware | SA:0xFD030000; SIZE:64; UNIT:KB; RegionTZ:Secure;\
WrAllowed:Read/Write; subsystemId:PMU Firmware | SA:0xFD040000; SIZE:64;\
UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write; subsystemId:PMU Firmware | \
SA:0xFD050000; SIZE:64; UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write;\
subsystemId:PMU Firmware | SA:0xFD610000; SIZE:512; UNIT:KB; RegionTZ:Secure;\
WrAllowed:Read/Write; subsystemId:PMU Firmware | SA:0xFD5D0000; SIZE:64;\
UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write; subsystemId:PMU Firmware |\
SA:0xFD1A0000 ; SIZE:1280; UNIT:KB; RegionTZ:Secure ; WrAllowed:Read/Write;\
subsystemId:Secure Subsystem} \
CONFIG.PSU__PROTECTION__LOCK_UNUSED_SEGMENTS {0} \
CONFIG.PSU__PROTECTION__LPD_SEGMENTS {\
SA:0xFF980000; SIZE:64; UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write;\
subsystemId:PMU Firmware| SA:0xFF5E0000; SIZE:2560; UNIT:KB; RegionTZ:Secure;\
WrAllowed:Read/Write; subsystemId:PMU Firmware| SA:0xFFCC0000; SIZE:64;\
UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write; subsystemId:PMU Firmware|\
SA:0xFF180000; SIZE:768; UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write;\
subsystemId:PMU Firmware| SA:0xFF410000; SIZE:640; UNIT:KB; RegionTZ:Secure;\
WrAllowed:Read/Write; subsystemId:PMU Firmware| SA:0xFFA70000; SIZE:64;\
UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write; subsystemId:PMU Firmware|\
SA:0xFF9A0000; SIZE:64; UNIT:KB; RegionTZ:Secure; WrAllowed:Read/Write;\
subsystemId:PMU Firmware|SA:0xFF5E0000 ; SIZE:2560; UNIT:KB; RegionTZ:Secure ;\
WrAllowed:Read/Write; subsystemId:Secure Subsystem|SA:0xFFCC0000 ; SIZE:64;\
UNIT:KB; RegionTZ:Secure ; WrAllowed:Read/Write; subsystemId:Secure\
Subsystem|SA:0xFF180000 ; SIZE:768; UNIT:KB; RegionTZ:Secure ;\
WrAllowed:Read/Write; subsystemId:Secure Subsystem|SA:0xFF9A0000 ; SIZE:64;\
UNIT:KB; RegionTZ:Secure ; WrAllowed:Read/Write; subsystemId:Secure Subsystem} \
CONFIG.PSU__PROTECTION__MASTERS {\
USB1:NonSecure;1|USB0:NonSecure;1|S_AXI_LPD:NA;0|S_AXI_HPC1_FPD:NA;0|S_AXI_HPC0_FPD:NA;1|S_AXI_HP3_FPD:NA;0|S_AXI_HP2_FPD:NA;0|S_AXI_HP1_FPD:NA;0|S_AXI_HP0_FPD:NA;0|S_AXI_ACP:NA;0|S_AXI_ACE:NA;0|SD1:NonSecure;1|SD0:NonSecure;1|SATA1:NonSecure;0|SATA0:NonSecure;0|RPU1:Secure;1|RPU0:Secure;1|QSPI:NonSecure;0|PMU:NA;1|PCIe:NonSecure;0|NAND:NonSecure;0|LDMA:NonSecure;1|GPU:NonSecure;1|GEM3:NonSecure;0|GEM2:NonSecure;0|GEM1:NonSecure;0|GEM0:NonSecure;0|FDMA:NonSecure;1|DP:NonSecure;1|DAP:NA;1|Coresight:NA;1|CSU:NA;1|APU:NA;1} \
CONFIG.PSU__PROTECTION__MASTERS_TZ {\
GEM0:NonSecure|SD1:NonSecure|GEM2:NonSecure|GEM1:NonSecure|GEM3:NonSecure|PCIe:NonSecure|DP:NonSecure|NAND:NonSecure|GPU:NonSecure|USB1:NonSecure|USB0:NonSecure|LDMA:NonSecure|FDMA:NonSecure|QSPI:NonSecure|SD0:NonSecure} \
CONFIG.PSU__PROTECTION__OCM_SEGMENTS {NONE} \
CONFIG.PSU__PROTECTION__PRESUBSYSTEMS {NONE} \
CONFIG.PSU__PROTECTION__SLAVES {\
LPD;USB3_1_XHCI;FE300000;FE3FFFFF;1|LPD;USB3_1;FF9E0000;FF9EFFFF;1|LPD;USB3_0_XHCI;FE200000;FE2FFFFF;1|LPD;USB3_0;FF9D0000;FF9DFFFF;1|LPD;UART1;FF010000;FF01FFFF;1|LPD;UART0;FF000000;FF00FFFF;1|LPD;TTC3;FF140000;FF14FFFF;1|LPD;TTC2;FF130000;FF13FFFF;1|LPD;TTC1;FF120000;FF12FFFF;1|LPD;TTC0;FF110000;FF11FFFF;1|FPD;SWDT1;FD4D0000;FD4DFFFF;1|LPD;SWDT0;FF150000;FF15FFFF;1|LPD;SPI1;FF050000;FF05FFFF;1|LPD;SPI0;FF040000;FF04FFFF;1|FPD;SMMU_REG;FD5F0000;FD5FFFFF;1|FPD;SMMU;FD800000;FDFFFFFF;1|FPD;SIOU;FD3D0000;FD3DFFFF;1|FPD;SERDES;FD400000;FD47FFFF;1|LPD;SD1;FF170000;FF17FFFF;1|LPD;SD0;FF160000;FF16FFFF;1|FPD;SATA;FD0C0000;FD0CFFFF;0|LPD;RTC;FFA60000;FFA6FFFF;1|LPD;RSA_CORE;FFCE0000;FFCEFFFF;1|LPD;RPU;FF9A0000;FF9AFFFF;1|LPD;R5_TCM_RAM_GLOBAL;FFE00000;FFE3FFFF;1|LPD;R5_1_Instruction_Cache;FFEC0000;FFECFFFF;1|LPD;R5_1_Data_Cache;FFED0000;FFEDFFFF;1|LPD;R5_1_BTCM_GLOBAL;FFEB0000;FFEBFFFF;1|LPD;R5_1_ATCM_GLOBAL;FFE90000;FFE9FFFF;1|LPD;R5_0_Instruction_Cache;FFE40000;FFE4FFFF;1|LPD;R5_0_Data_Cache;FFE50000;FFE5FFFF;1|LPD;R5_0_BTCM_GLOBAL;FFE20000;FFE2FFFF;1|LPD;R5_0_ATCM_GLOBAL;FFE00000;FFE0FFFF;1|LPD;QSPI_Linear_Address;C0000000;DFFFFFFF;1|LPD;QSPI;FF0F0000;FF0FFFFF;0|LPD;PMU_RAM;FFDC0000;FFDDFFFF;1|LPD;PMU_GLOBAL;FFD80000;FFDBFFFF;1|FPD;PCIE_MAIN;FD0E0000;FD0EFFFF;0|FPD;PCIE_LOW;E0000000;EFFFFFFF;0|FPD;PCIE_HIGH2;8000000000;BFFFFFFFFF;0|FPD;PCIE_HIGH1;600000000;7FFFFFFFF;0|FPD;PCIE_DMA;FD0F0000;FD0FFFFF;0|FPD;PCIE_ATTRIB;FD480000;FD48FFFF;0|LPD;OCM_XMPU_CFG;FFA70000;FFA7FFFF;1|LPD;OCM_SLCR;FF960000;FF96FFFF;1|OCM;OCM;FFFC0000;FFFFFFFF;1|LPD;NAND;FF100000;FF10FFFF;0|LPD;MBISTJTAG;FFCF0000;FFCFFFFF;1|LPD;LPD_XPPU_SINK;FF9C0000;FF9CFFFF;1|LPD;LPD_XPPU;FF980000;FF98FFFF;1|LPD;LPD_SLCR_SECURE;FF4B0000;FF4DFFFF;1|LPD;LPD_SLCR;FF410000;FF4AFFFF;1|LPD;LPD_GPV;FE100000;FE1FFFFF;1|LPD;LPD_DMA_7;FFAF0000;FFAFFFFF;1|LPD;LPD_DMA_6;FFAE0000;FFAEFFFF;1|LPD;LPD_DMA_5;FFAD0000;FFADFFFF;1|LPD;LPD_DMA_4;FFAC0000;FFACFFFF;1|LPD;LPD_DMA_3;FFAB0000;FFABFFFF;1|LPD;LPD_DMA_2;FFAA0000;FFAAFFFF;1|LPD;LPD_DMA_1;FFA90000;FFA9FFFF;1|LPD;LPD_DMA_0;FFA80000;FFA8FFFF;1|LPD;IPI_CTRL;FF380000;FF3FFFFF;1|LPD;IOU_SLCR;FF180000;FF23FFFF;1|LPD;IOU_SECURE_SLCR;FF240000;FF24FFFF;1|LPD;IOU_SCNTRS;FF260000;FF26FFFF;1|LPD;IOU_SCNTR;FF250000;FF25FFFF;1|LPD;IOU_GPV;FE000000;FE0FFFFF;1|LPD;I2C1;FF030000;FF03FFFF;1|LPD;I2C0;FF020000;FF02FFFF;0|FPD;GPU;FD4B0000;FD4BFFFF;1|LPD;GPIO;FF0A0000;FF0AFFFF;1|LPD;GEM3;FF0E0000;FF0EFFFF;0|LPD;GEM2;FF0D0000;FF0DFFFF;0|LPD;GEM1;FF0C0000;FF0CFFFF;0|LPD;GEM0;FF0B0000;FF0BFFFF;0|FPD;FPD_XMPU_SINK;FD4F0000;FD4FFFFF;1|FPD;FPD_XMPU_CFG;FD5D0000;FD5DFFFF;1|FPD;FPD_SLCR_SECURE;FD690000;FD6CFFFF;1|FPD;FPD_SLCR;FD610000;FD68FFFF;1|FPD;FPD_DMA_CH7;FD570000;FD57FFFF;1|FPD;FPD_DMA_CH6;FD560000;FD56FFFF;1|FPD;FPD_DMA_CH5;FD550000;FD55FFFF;1|FPD;FPD_DMA_CH4;FD540000;FD54FFFF;1|FPD;FPD_DMA_CH3;FD530000;FD53FFFF;1|FPD;FPD_DMA_CH2;FD520000;FD52FFFF;1|FPD;FPD_DMA_CH1;FD510000;FD51FFFF;1|FPD;FPD_DMA_CH0;FD500000;FD50FFFF;1|LPD;EFUSE;FFCC0000;FFCCFFFF;1|FPD;Display\
Port;FD4A0000;FD4AFFFF;1|FPD;DPDMA;FD4C0000;FD4CFFFF;1|FPD;DDR_XMPU5_CFG;FD050000;FD05FFFF;1|FPD;DDR_XMPU4_CFG;FD040000;FD04FFFF;1|FPD;DDR_XMPU3_CFG;FD030000;FD03FFFF;1|FPD;DDR_XMPU2_CFG;FD020000;FD02FFFF;1|FPD;DDR_XMPU1_CFG;FD010000;FD01FFFF;1|FPD;DDR_XMPU0_CFG;FD000000;FD00FFFF;1|FPD;DDR_QOS_CTRL;FD090000;FD09FFFF;1|FPD;DDR_PHY;FD080000;FD08FFFF;1|DDR;DDR_LOW;0;7FFFFFFF;1|DDR;DDR_HIGH;800000000;800000000;0|FPD;DDDR_CTRL;FD070000;FD070FFF;1|LPD;Coresight;FE800000;FEFFFFFF;1|LPD;CSU_DMA;FFC80000;FFC9FFFF;1|LPD;CSU;FFCA0000;FFCAFFFF;1|LPD;CRL_APB;FF5E0000;FF85FFFF;1|FPD;CRF_APB;FD1A0000;FD2DFFFF;1|FPD;CCI_REG;FD5E0000;FD5EFFFF;1|LPD;CAN1;FF070000;FF07FFFF;0|LPD;CAN0;FF060000;FF06FFFF;0|FPD;APU;FD5C0000;FD5CFFFF;1|LPD;APM_INTC_IOU;FFA20000;FFA2FFFF;1|LPD;APM_FPD_LPD;FFA30000;FFA3FFFF;1|FPD;APM_5;FD490000;FD49FFFF;1|FPD;APM_0;FD0B0000;FD0BFFFF;1|LPD;APM2;FFA10000;FFA1FFFF;1|LPD;APM1;FFA00000;FFA0FFFF;1|LPD;AMS;FFA50000;FFA5FFFF;1|FPD;AFI_5;FD3B0000;FD3BFFFF;1|FPD;AFI_4;FD3A0000;FD3AFFFF;1|FPD;AFI_3;FD390000;FD39FFFF;1|FPD;AFI_2;FD380000;FD38FFFF;1|FPD;AFI_1;FD370000;FD37FFFF;1|FPD;AFI_0;FD360000;FD36FFFF;1|LPD;AFIFM6;FF9B0000;FF9BFFFF;1|FPD;ACPU_GIC;F9010000;F907FFFF;1} \
CONFIG.PSU__PROTECTION__SUBSYSTEMS {PMU Firmware:PMU|Secure Subsystem:} \
CONFIG.PSU__PSS_ALT_REF_CLK__ENABLE {0} \
CONFIG.PSU__PSS_ALT_REF_CLK__FREQMHZ {33.333} \
CONFIG.PSU__PSS_REF_CLK__FREQMHZ {33.333333} \
CONFIG.PSU__QSPI_COHERENCY {0} \
CONFIG.PSU__QSPI_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__QSPI__GRP_FBCLK__ENABLE {0} \
CONFIG.PSU__QSPI__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__REPORT__DBGLOG {0} \
CONFIG.PSU__RPU_COHERENCY {0} \
CONFIG.PSU__RPU__POWER__ON {1} \
CONFIG.PSU__SATA__LANE0__ENABLE {0} \
CONFIG.PSU__SATA__LANE1__ENABLE {0} \
CONFIG.PSU__SATA__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__SAXIGP0__DATA_WIDTH {128} \
CONFIG.PSU__SAXIGP1__DATA_WIDTH {128} \
CONFIG.PSU__SAXIGP2__DATA_WIDTH {128} \
CONFIG.PSU__SAXIGP3__DATA_WIDTH {128} \
CONFIG.PSU__SAXIGP4__DATA_WIDTH {128} \
CONFIG.PSU__SAXIGP5__DATA_WIDTH {128} \
CONFIG.PSU__SAXIGP6__DATA_WIDTH {128} \
CONFIG.PSU__SD0_COHERENCY {0} \
CONFIG.PSU__SD0_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__SD0__CLK_100_SDR_OTAP_DLY {0x0} \
CONFIG.PSU__SD0__CLK_200_SDR_OTAP_DLY {0x0} \
CONFIG.PSU__SD0__CLK_50_DDR_ITAP_DLY {0x0} \
CONFIG.PSU__SD0__CLK_50_DDR_OTAP_DLY {0x0} \
CONFIG.PSU__SD0__CLK_50_SDR_ITAP_DLY {0x15} \
CONFIG.PSU__SD0__CLK_50_SDR_OTAP_DLY {0x5} \
CONFIG.PSU__SD0__DATA_TRANSFER_MODE {4Bit} \
CONFIG.PSU__SD0__GRP_CD__ENABLE {1} \
CONFIG.PSU__SD0__GRP_CD__IO {MIO 24} \
CONFIG.PSU__SD0__GRP_POW__ENABLE {0} \
CONFIG.PSU__SD0__GRP_WP__ENABLE {0} \
CONFIG.PSU__SD0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__SD0__PERIPHERAL__IO {MIO 13 .. 16 21 22} \
CONFIG.PSU__SD0__RESET__ENABLE {0} \
CONFIG.PSU__SD0__SLOT_TYPE {SD 2.0} \
CONFIG.PSU__SD1_COHERENCY {0} \
CONFIG.PSU__SD1_ROUTE_THROUGH_FPD {0} \
CONFIG.PSU__SD1__CLK_100_SDR_OTAP_DLY {0x0} \
CONFIG.PSU__SD1__CLK_200_SDR_OTAP_DLY {0x0} \
CONFIG.PSU__SD1__CLK_50_DDR_ITAP_DLY {0x0} \
CONFIG.PSU__SD1__CLK_50_DDR_OTAP_DLY {0x0} \
CONFIG.PSU__SD1__CLK_50_SDR_ITAP_DLY {0x15} \
CONFIG.PSU__SD1__CLK_50_SDR_OTAP_DLY {0x5} \
CONFIG.PSU__SD1__DATA_TRANSFER_MODE {4Bit} \
CONFIG.PSU__SD1__GRP_CD__ENABLE {0} \
CONFIG.PSU__SD1__GRP_POW__ENABLE {0} \
CONFIG.PSU__SD1__GRP_WP__ENABLE {0} \
CONFIG.PSU__SD1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__SD1__PERIPHERAL__IO {MIO 46 .. 51} \
CONFIG.PSU__SD1__RESET__ENABLE {0} \
CONFIG.PSU__SD1__SLOT_TYPE {SD 2.0} \
CONFIG.PSU__SPI0_LOOP_SPI1__ENABLE {0} \
CONFIG.PSU__SPI0__GRP_SS0__ENABLE {1} \
CONFIG.PSU__SPI0__GRP_SS0__IO {MIO 41} \
CONFIG.PSU__SPI0__GRP_SS1__ENABLE {0} \
CONFIG.PSU__SPI0__GRP_SS2__ENABLE {0} \
CONFIG.PSU__SPI0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__SPI0__PERIPHERAL__IO {MIO 38 .. 43} \
CONFIG.PSU__SPI1__GRP_SS0__ENABLE {1} \
CONFIG.PSU__SPI1__GRP_SS0__IO {MIO 9} \
CONFIG.PSU__SPI1__GRP_SS1__ENABLE {0} \
CONFIG.PSU__SPI1__GRP_SS2__ENABLE {0} \
CONFIG.PSU__SPI1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__SPI1__PERIPHERAL__IO {MIO 6 .. 11} \
CONFIG.PSU__SWDT0__CLOCK__ENABLE {0} \
CONFIG.PSU__SWDT0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__SWDT0__PERIPHERAL__IO {NA} \
CONFIG.PSU__SWDT0__RESET__ENABLE {0} \
CONFIG.PSU__SWDT1__CLOCK__ENABLE {0} \
CONFIG.PSU__SWDT1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__SWDT1__PERIPHERAL__IO {NA} \
CONFIG.PSU__SWDT1__RESET__ENABLE {0} \
CONFIG.PSU__TCM0A__POWER__ON {1} \
CONFIG.PSU__TCM0B__POWER__ON {1} \
CONFIG.PSU__TCM1A__POWER__ON {1} \
CONFIG.PSU__TCM1B__POWER__ON {1} \
CONFIG.PSU__TESTSCAN__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__TRACE_PIPELINE_WIDTH {8} \
CONFIG.PSU__TRACE__INTERNAL_WIDTH {32} \
CONFIG.PSU__TRACE__PERIPHERAL__ENABLE {0} \
CONFIG.PSU__TRISTATE__INVERTED {1} \
CONFIG.PSU__TSU__BUFG_PORT_PAIR {0} \
CONFIG.PSU__TTC0__CLOCK__ENABLE {0} \
CONFIG.PSU__TTC0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__TTC0__PERIPHERAL__IO {NA} \
CONFIG.PSU__TTC0__WAVEOUT__ENABLE {0} \
CONFIG.PSU__TTC1__CLOCK__ENABLE {0} \
CONFIG.PSU__TTC1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__TTC1__PERIPHERAL__IO {NA} \
CONFIG.PSU__TTC1__WAVEOUT__ENABLE {0} \
CONFIG.PSU__TTC2__CLOCK__ENABLE {0} \
CONFIG.PSU__TTC2__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__TTC2__PERIPHERAL__IO {NA} \
CONFIG.PSU__TTC2__WAVEOUT__ENABLE {0} \
CONFIG.PSU__TTC3__CLOCK__ENABLE {0} \
CONFIG.PSU__TTC3__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__TTC3__PERIPHERAL__IO {NA} \
CONFIG.PSU__TTC3__WAVEOUT__ENABLE {0} \
CONFIG.PSU__UART0_LOOP_UART1__ENABLE {0} \
CONFIG.PSU__UART0__BAUD_RATE {115200} \
CONFIG.PSU__UART0__MODEM__ENABLE {0} \
CONFIG.PSU__UART0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__UART0__PERIPHERAL__IO {MIO 2 .. 3} \
CONFIG.PSU__UART1__BAUD_RATE {115200} \
CONFIG.PSU__UART1__MODEM__ENABLE {0} \
CONFIG.PSU__UART1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__UART1__PERIPHERAL__IO {MIO 0 .. 1} \
CONFIG.PSU__USB0_COHERENCY {0} \
CONFIG.PSU__USB0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__USB0__PERIPHERAL__IO {MIO 52 .. 63} \
CONFIG.PSU__USB0__REF_CLK_FREQ {26} \
CONFIG.PSU__USB0__REF_CLK_SEL {Ref Clk0} \
CONFIG.PSU__USB0__RESET__ENABLE {0} \
CONFIG.PSU__USB1_COHERENCY {0} \
CONFIG.PSU__USB1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__USB1__PERIPHERAL__IO {MIO 64 .. 75} \
CONFIG.PSU__USB1__REF_CLK_FREQ {26} \
CONFIG.PSU__USB1__REF_CLK_SEL {Ref Clk0} \
CONFIG.PSU__USB1__RESET__ENABLE {0} \
CONFIG.PSU__USB2_0__EMIO__ENABLE {0} \
CONFIG.PSU__USB2_1__EMIO__ENABLE {0} \
CONFIG.PSU__USB3_0__EMIO__ENABLE {0} \
CONFIG.PSU__USB3_0__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__USB3_0__PERIPHERAL__IO {GT Lane2} \
CONFIG.PSU__USB3_1__EMIO__ENABLE {0} \
CONFIG.PSU__USB3_1__PERIPHERAL__ENABLE {1} \
CONFIG.PSU__USB3_1__PERIPHERAL__IO {GT Lane3} \
CONFIG.PSU__USB__RESET__MODE {Boot Pin} \
CONFIG.PSU__USB__RESET__POLARITY {Active Low} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP0 {0} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP1 {0} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP2 {0} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP3 {0} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP4 {0} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP5 {0} \
CONFIG.PSU__USE_DIFF_RW_CLK_GP6 {0} \
CONFIG.PSU__USE__ADMA {0} \
CONFIG.PSU__USE__APU_LEGACY_INTERRUPT {0} \
CONFIG.PSU__USE__AUDIO {0} \
CONFIG.PSU__USE__CLK {0} \
CONFIG.PSU__USE__CLK0 {0} \
CONFIG.PSU__USE__CLK1 {0} \
CONFIG.PSU__USE__CLK2 {0} \
CONFIG.PSU__USE__CLK3 {0} \
CONFIG.PSU__USE__CROSS_TRIGGER {0} \
CONFIG.PSU__USE__DDR_INTF_REQUESTED {0} \
CONFIG.PSU__USE__DEBUG__TEST {0} \
CONFIG.PSU__USE__EVENT_RPU {0} \
CONFIG.PSU__USE__FABRIC__RST {1} \
CONFIG.PSU__USE__FTM {0} \
CONFIG.PSU__USE__GDMA {0} \
CONFIG.PSU__USE__IRQ {0} \
CONFIG.PSU__USE__IRQ0 {1} \
CONFIG.PSU__USE__IRQ1 {0} \
CONFIG.PSU__USE__M_AXI_GP0 {1} \
CONFIG.PSU__USE__M_AXI_GP1 {0} \
CONFIG.PSU__USE__M_AXI_GP2 {0} \
CONFIG.PSU__USE__PROC_EVENT_BUS {0} \
CONFIG.PSU__USE__RPU_LEGACY_INTERRUPT {0} \
CONFIG.PSU__USE__RST0 {0} \
CONFIG.PSU__USE__RST1 {0} \
CONFIG.PSU__USE__RST2 {0} \
CONFIG.PSU__USE__RST3 {0} \
CONFIG.PSU__USE__RTC {0} \
CONFIG.PSU__USE__STM {0} \
CONFIG.PSU__USE__S_AXI_ACE {0} \
CONFIG.PSU__USE__S_AXI_ACP {0} \
CONFIG.PSU__USE__S_AXI_GP0 {1} \
CONFIG.PSU__USE__S_AXI_GP1 {0} \
CONFIG.PSU__USE__S_AXI_GP2 {0} \
CONFIG.PSU__USE__S_AXI_GP3 {0} \
CONFIG.PSU__USE__S_AXI_GP4 {0} \
CONFIG.PSU__USE__S_AXI_GP5 {0} \
CONFIG.PSU__USE__S_AXI_GP6 {0} \
CONFIG.PSU__USE__USB3_0_HUB {0} \
CONFIG.PSU__USE__USB3_1_HUB {0} \
CONFIG.PSU__USE__VIDEO {0} \
CONFIG.PSU__VIDEO_REF_CLK__ENABLE {0} \
CONFIG.PSU__VIDEO_REF_CLK__FREQMHZ {33.333} \
CONFIG.QSPI_BOARD_INTERFACE {custom} \
CONFIG.SATA_BOARD_INTERFACE {custom} \
CONFIG.SD0_BOARD_INTERFACE {custom} \
CONFIG.SD1_BOARD_INTERFACE {custom} \
CONFIG.SPI0_BOARD_INTERFACE {custom} \
CONFIG.SPI1_BOARD_INTERFACE {custom} \
CONFIG.SUBPRESET1 {Custom} \
CONFIG.SUBPRESET2 {Custom} \
CONFIG.SWDT0_BOARD_INTERFACE {custom} \
CONFIG.SWDT1_BOARD_INTERFACE {custom} \
CONFIG.TRACE_BOARD_INTERFACE {custom} \
CONFIG.TTC0_BOARD_INTERFACE {custom} \
CONFIG.TTC1_BOARD_INTERFACE {custom} \
CONFIG.TTC2_BOARD_INTERFACE {custom} \
CONFIG.TTC3_BOARD_INTERFACE {custom} \
CONFIG.UART0_BOARD_INTERFACE {custom} \
CONFIG.UART1_BOARD_INTERFACE {custom} \
CONFIG.USB0_BOARD_INTERFACE {custom} \
CONFIG.USB1_BOARD_INTERFACE {custom} \
] $zynq_ultra_ps_e_0
# Create interface connections
connect_bd_intf_net -intf_net S00_AXI_1 [get_bd_intf_pins ps8_0_axi_periph/S00_AXI] [get_bd_intf_pins zynq_ultra_ps_e_0/M_AXI_HPM0_FPD]
connect_bd_intf_net -intf_net axi_vdma_0_M_AXI_S2MM [get_bd_intf_pins axi_vdma_0/M_AXI_S2MM] [get_bd_intf_pins zynq_ultra_ps_e_0/S_AXI_HPC0_FPD]
connect_bd_intf_net -intf_net demosaic_root_0_p_odata [get_bd_intf_pins axi_vdma_0/S_AXIS_S2MM] [get_bd_intf_pins demosaic_root_0/p_odata]
connect_bd_intf_net -intf_net mipi_csi2_rx_subsyst_0_video_out [get_bd_intf_pins demosaic_root_0/p_idata] [get_bd_intf_pins mipi_csi2_rx_subsyst_0/video_out]
connect_bd_intf_net -intf_net mipi_phy_csi_1 [get_bd_intf_ports mipi_phy_csi] [get_bd_intf_pins mipi_csi2_rx_subsyst_0/mipi_phy_if]
connect_bd_intf_net -intf_net ps8_0_axi_periph_M00_AXI [get_bd_intf_pins mipi_csi2_rx_subsyst_0/csirxss_s_axi] [get_bd_intf_pins ps8_0_axi_periph/M00_AXI]
connect_bd_intf_net -intf_net ps8_0_axi_periph_M01_AXI [get_bd_intf_pins axi_vdma_0/S_AXI_LITE] [get_bd_intf_pins ps8_0_axi_periph/M01_AXI]
connect_bd_intf_net -intf_net ps8_0_axi_periph_M02_AXI [get_bd_intf_pins demosaic_root_0/s_axi_BUS_AXI4LS] [get_bd_intf_pins ps8_0_axi_periph/M02_AXI]
# Create port connections
connect_bd_net -net axi_vdma_0_s2mm_introut [get_bd_pins axi_vdma_0/s2mm_introut] [get_bd_pins zynq_ultra_ps_e_0/pl_ps_irq0]
connect_bd_net -net clk_wiz_0_clk_out1 [get_bd_pins clk_wiz_0/clk_out1] [get_bd_pins mipi_csi2_rx_subsyst_0/dphy_clk_200M]
connect_bd_net -net rst_ps8_0_99M_interconnect_aresetn [get_bd_pins ps8_0_axi_periph/ARESETN] [get_bd_pins rst_ps8_0_99M/interconnect_aresetn]
connect_bd_net -net rst_ps8_0_99M_peripheral_aresetn [get_bd_pins axi_vdma_0/axi_resetn] [get_bd_pins demosaic_root_0/ap_rst_n] [get_bd_pins mipi_csi2_rx_subsyst_0/lite_aresetn] [get_bd_pins mipi_csi2_rx_subsyst_0/video_aresetn] [get_bd_pins ps8_0_axi_periph/M00_ARESETN] [get_bd_pins ps8_0_axi_periph/M01_ARESETN] [get_bd_pins ps8_0_axi_periph/M02_ARESETN] [get_bd_pins ps8_0_axi_periph/S00_ARESETN] [get_bd_pins rst_ps8_0_99M/peripheral_aresetn]
connect_bd_net -net util_vector_logic_0_Res [get_bd_pins clk_wiz_0/reset] [get_bd_pins util_vector_logic_0/Res]
connect_bd_net -net zynq_ultra_ps_e_0_pl_clk0 [get_bd_pins axi_vdma_0/m_axi_s2mm_aclk] [get_bd_pins axi_vdma_0/s_axi_lite_aclk] [get_bd_pins axi_vdma_0/s_axis_s2mm_aclk] [get_bd_pins clk_wiz_0/clk_in1] [get_bd_pins demosaic_root_0/ap_clk] [get_bd_pins mipi_csi2_rx_subsyst_0/lite_aclk] [get_bd_pins mipi_csi2_rx_subsyst_0/video_aclk] [get_bd_pins ps8_0_axi_periph/ACLK] [get_bd_pins ps8_0_axi_periph/M00_ACLK] [get_bd_pins ps8_0_axi_periph/M01_ACLK] [get_bd_pins ps8_0_axi_periph/M02_ACLK] [get_bd_pins ps8_0_axi_periph/S00_ACLK] [get_bd_pins rst_ps8_0_99M/slowest_sync_clk] [get_bd_pins zynq_ultra_ps_e_0/maxihpm0_fpd_aclk] [get_bd_pins zynq_ultra_ps_e_0/pl_clk0] [get_bd_pins zynq_ultra_ps_e_0/saxihpc0_fpd_aclk]
connect_bd_net -net zynq_ultra_ps_e_0_pl_resetn0 [get_bd_pins rst_ps8_0_99M/ext_reset_in] [get_bd_pins util_vector_logic_0/Op1] [get_bd_pins zynq_ultra_ps_e_0/pl_resetn0]
# Create address segments
assign_bd_address -offset 0x00000000 -range 0x80000000 -target_address_space [get_bd_addr_spaces axi_vdma_0/Data_S2MM] [get_bd_addr_segs zynq_ultra_ps_e_0/SAXIGP0/HPC0_DDR_LOW] -force
assign_bd_address -offset 0xFF000000 -range 0x01000000 -target_address_space [get_bd_addr_spaces axi_vdma_0/Data_S2MM] [get_bd_addr_segs zynq_ultra_ps_e_0/SAXIGP0/HPC0_LPS_OCM] -force
assign_bd_address -offset 0xA0010000 -range 0x00001000 -target_address_space [get_bd_addr_spaces zynq_ultra_ps_e_0/Data] [get_bd_addr_segs axi_vdma_0/S_AXI_LITE/Reg] -force
assign_bd_address -offset 0xA0020000 -range 0x00010000 -target_address_space [get_bd_addr_spaces zynq_ultra_ps_e_0/Data] [get_bd_addr_segs demosaic_root_0/s_axi_BUS_AXI4LS/Reg] -force
assign_bd_address -offset 0xA0000000 -range 0x00010000 -target_address_space [get_bd_addr_spaces zynq_ultra_ps_e_0/Data] [get_bd_addr_segs mipi_csi2_rx_subsyst_0/csirxss_s_axi/Reg] -force
# Perform GUI Layout
regenerate_bd_layout -layout_string {
"ActiveEmotionalView":"Default View",
"Default View_ScaleFactor":"0.417982",
"Default View_TopLeft":"-134,-323",
"ExpandedHierarchyInLayout":"",
"guistr":"# # String gsaved with Nlview 7.0r4 2019-12-20 bk=1.5203 VDI=41 GEI=36 GUI=JA:10.0 TLS
# -string -flagsOSRD
preplace port mipi_phy_csi -pg 1 -lvl 0 -x 0 -y 160 -defaultsOSRD
preplace inst axi_vdma_0 -pg 1 -lvl 5 -x 1600 -y 190 -defaultsOSRD
preplace inst clk_wiz_0 -pg 1 -lvl 2 -x 510 -y 90 -defaultsOSRD
preplace inst mipi_csi2_rx_subsyst_0 -pg 1 -lvl 3 -x 870 -y 220 -defaultsOSRD
preplace inst demosaic_root_0 -pg 1 -lvl 4 -x 1210 -y 470 -defaultsOSRD
preplace inst ps8_0_axi_periph -pg 1 -lvl 7 -x 2590 -y 170 -defaultsOSRD
preplace inst rst_ps8_0_99M -pg 1 -lvl 2 -x 510 -y 330 -defaultsOSRD
preplace inst util_vector_logic_0 -pg 1 -lvl 1 -x 170 -y 80 -defaultsOSRD
preplace inst zynq_ultra_ps_e_0 -pg 1 -lvl 6 -x 2100 -y 180 -defaultsOSRD
preplace netloc axi_vdma_0_s2mm_introut 1 5 1 N 210
preplace netloc clk_wiz_0_clk_out1 1 2 1 700 80n
preplace netloc rst_ps8_0_99M_interconnect_aresetn 1 2 5 690J 50 NJ 50 NJ 50 NJ 50 2430
preplace netloc rst_ps8_0_99M_peripheral_aresetn 1 2 5 720 100 1010 100 1380 60 NJ 60 2410
preplace netloc util_vector_logic_0_Res 1 1 1 NJ 80
preplace netloc zynq_ultra_ps_e_0_pl_clk0 1 1 6 330 10 710 90 1030 90 1400 70 1800 90 2440
preplace netloc zynq_ultra_ps_e_0_pl_resetn0 1 0 7 20 20 320 20 NJ 20 NJ 20 NJ 20 NJ 20 2400
preplace netloc S00_AXI_1 1 6 1 2420 70n
preplace netloc axi_vdma_0_M_AXI_S2MM 1 5 1 1790 150n
preplace netloc demosaic_root_0_p_odata 1 4 1 1390 150n
preplace netloc mipi_csi2_rx_subsyst_0_video_out 1 3 1 1020 170n
preplace netloc mipi_phy_csi_1 1 0 3 NJ 160 NJ 160 NJ
preplace netloc ps8_0_axi_periph_M00_AXI 1 2 6 730 340 NJ 340 NJ 340 NJ 340 NJ 340 2750
preplace netloc ps8_0_axi_periph_M01_AXI 1 4 4 1410 10 NJ 10 NJ 10 2760
preplace netloc ps8_0_axi_periph_M02_AXI 1 3 5 1040 350 NJ 350 NJ 350 NJ 350 2740
levelinfo -pg 1 0 170 510 870 1210 1600 2100 2590 2780
pagesize -pg 1 -db -bbox -sgen -140 0 2780 560
"
}
# Restore current instance
current_bd_instance $oldCurInst
validate_bd_design
save_bd_design
close_bd_design $design_name
}
# End of cr_bd_design_1()
cr_bd_design_1 ""
set_property EXCLUDE_DEBUG_LOGIC "0" [get_files design_1.bd ]
set_property GENERATE_SYNTH_CHECKPOINT "1" [get_files design_1.bd ]
set_property IS_ENABLED "1" [get_files design_1.bd ]
set_property IS_GLOBAL_INCLUDE "0" [get_files design_1.bd ]
set_property LIBRARY "xil_defaultlib" [get_files design_1.bd ]
set_property PATH_MODE "RelativeFirst" [get_files design_1.bd ]
set_property PFM_NAME "" [get_files design_1.bd ]
set_property REGISTERED_WITH_MANAGER "1" [get_files design_1.bd ]
set_property SYNTH_CHECKPOINT_MODE "Hierarchical" [get_files design_1.bd ]
set_property USED_IN "synthesis implementation simulation" [get_files design_1.bd ]
set_property USED_IN_IMPLEMENTATION "1" [get_files design_1.bd ]
set_property USED_IN_SIMULATION "1" [get_files design_1.bd ]
set_property USED_IN_SYNTHESIS "1" [get_files design_1.bd ]
set idrFlowPropertiesConstraints ""
catch {
set idrFlowPropertiesConstraints [get_param runs.disableIDRFlowPropertyConstraints]
set_param runs.disableIDRFlowPropertyConstraints 1
}
# Create 'synth_1' run (if not found)
if {[string equal [get_runs -quiet synth_1] ""]} {
create_run -name synth_1 -part xczu3eg-sbva484-1-i -flow {Vivado Synthesis 2018} -strategy "Vivado Synthesis Defaults" -report_strategy {No Reports} -constrset constrs_1
} else {
set_property strategy "Vivado Synthesis Defaults" [get_runs synth_1]
set_property flow "Vivado Synthesis 2018" [get_runs synth_1]
}
set obj [get_runs synth_1]
set_property set_report_strategy_name 1 $obj
set_property report_strategy {Vivado Synthesis Default Reports} $obj
set_property set_report_strategy_name 0 $obj
# Create 'synth_1_synth_report_utilization_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs synth_1] synth_1_synth_report_utilization_0] "" ] } {
create_report_config -report_name synth_1_synth_report_utilization_0 -report_type report_utilization:1.0 -steps synth_design -runs synth_1
}
set obj [get_report_configs -of_objects [get_runs synth_1] synth_1_synth_report_utilization_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Utilization - Synth Design" -objects $obj
set_property -name "options.pblocks" -value "" -objects $obj
set_property -name "options.cells" -value "" -objects $obj
set_property -name "options.slr" -value "0" -objects $obj
set_property -name "options.packthru" -value "0" -objects $obj
set_property -name "options.hierarchical" -value "0" -objects $obj
set_property -name "options.hierarchical_depth" -value "" -objects $obj
set_property -name "options.hierarchical_percentages" -value "0" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
set obj [get_runs synth_1]
set_property -name "constrset" -value "constrs_1" -objects $obj
set_property -name "description" -value "Vivado Synthesis Defaults" -objects $obj
set_property -name "flow" -value "Vivado Synthesis 2018" -objects $obj
set_property -name "name" -value "synth_1" -objects $obj
set_property -name "needs_refresh" -value "0" -objects $obj
set_property -name "srcset" -value "sources_1" -objects $obj
set_property -name "incremental_checkpoint" -value "" -objects $obj
set_property -name "auto_incremental_checkpoint" -value "1" -objects $obj
set_property -name "rqs_files" -value "" -objects $obj
set_property -name "auto_rqs.suggestion_run" -value "" -objects $obj
set_property -name "incremental_checkpoint.more_options" -value "" -objects $obj
set_property -name "include_in_archive" -value "1" -objects $obj
set_property -name "gen_full_bitstream" -value "1" -objects $obj
set_property -name "write_incremental_synth_checkpoint" -value "0" -objects $obj
set_property -name "auto_incremental_checkpoint.directory" -value "$proj_dir/ultra96_design.srcs/utils_1/imports/synth_1" -objects $obj
set_property -name "min_rqa_score" -value "0" -objects $obj
set_property -name "strategy" -value "Vivado Synthesis Defaults" -objects $obj
set_property -name "steps.synth_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.synth_design.tcl.post" -value "" -objects $obj
set_property -name "steps.synth_design.args.flatten_hierarchy" -value "rebuilt" -objects $obj
set_property -name "steps.synth_design.args.gated_clock_conversion" -value "off" -objects $obj
set_property -name "steps.synth_design.args.bufg" -value "12" -objects $obj
set_property -name "steps.synth_design.args.fanout_limit" -value "10000" -objects $obj
set_property -name "steps.synth_design.args.directive" -value "Default" -objects $obj
set_property -name "steps.synth_design.args.retiming" -value "0" -objects $obj
set_property -name "steps.synth_design.args.fsm_extraction" -value "auto" -objects $obj
set_property -name "steps.synth_design.args.keep_equivalent_registers" -value "0" -objects $obj
set_property -name "steps.synth_design.args.resource_sharing" -value "auto" -objects $obj
set_property -name "steps.synth_design.args.control_set_opt_threshold" -value "auto" -objects $obj
set_property -name "steps.synth_design.args.no_lc" -value "0" -objects $obj
set_property -name "steps.synth_design.args.no_srlextract" -value "0" -objects $obj
set_property -name "steps.synth_design.args.shreg_min_size" -value "3" -objects $obj
set_property -name "steps.synth_design.args.max_bram" -value "-1" -objects $obj
set_property -name "steps.synth_design.args.max_uram" -value "-1" -objects $obj
set_property -name "steps.synth_design.args.max_dsp" -value "-1" -objects $obj
set_property -name "steps.synth_design.args.max_bram_cascade_height" -value "-1" -objects $obj
set_property -name "steps.synth_design.args.max_uram_cascade_height" -value "-1" -objects $obj
set_property -name "steps.synth_design.args.cascade_dsp" -value "auto" -objects $obj
set_property -name "steps.synth_design.args.assert" -value "0" -objects $obj
set_property -name "steps.synth_design.args.more options" -value "" -objects $obj
# set the current synth run
current_run -synthesis [get_runs synth_1]
# Create 'impl_1' run (if not found)
if {[string equal [get_runs -quiet impl_1] ""]} {
create_run -name impl_1 -part xczu3eg-sbva484-1-i -flow {Vivado Implementation 2018} -strategy "Vivado Implementation Defaults" -report_strategy {No Reports} -constrset constrs_1 -parent_run synth_1
} else {
set_property strategy "Vivado Implementation Defaults" [get_runs impl_1]
set_property flow "Vivado Implementation 2018" [get_runs impl_1]
}
set obj [get_runs impl_1]
set_property set_report_strategy_name 1 $obj
set_property report_strategy {Vivado Implementation Default Reports} $obj
set_property set_report_strategy_name 0 $obj
# Create 'impl_1_init_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_init_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_init_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps init_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_init_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Timing Summary - Design Initialization" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_opt_report_drc_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_drc_0] "" ] } {
create_report_config -report_name impl_1_opt_report_drc_0 -report_type report_drc:1.0 -steps opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_drc_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "DRC - Opt Design" -objects $obj
set_property -name "options.upgrade_cw" -value "0" -objects $obj
set_property -name "options.checks" -value "" -objects $obj
set_property -name "options.ruledecks" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Timing Summary - Opt Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_power_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_power_opt_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_power_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps power_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_power_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Timing Summary - Power Opt Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_place_report_io_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_io_0] "" ] } {
create_report_config -report_name impl_1_place_report_io_0 -report_type report_io:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_io_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "IO - Place Design" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_place_report_utilization_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_utilization_0] "" ] } {
create_report_config -report_name impl_1_place_report_utilization_0 -report_type report_utilization:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_utilization_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Utilization - Place Design" -objects $obj
set_property -name "options.pblocks" -value "" -objects $obj
set_property -name "options.cells" -value "" -objects $obj
set_property -name "options.slr" -value "0" -objects $obj
set_property -name "options.packthru" -value "0" -objects $obj
set_property -name "options.hierarchical" -value "0" -objects $obj
set_property -name "options.hierarchical_depth" -value "" -objects $obj
set_property -name "options.hierarchical_percentages" -value "0" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_place_report_control_sets_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_control_sets_0] "" ] } {
create_report_config -report_name impl_1_place_report_control_sets_0 -report_type report_control_sets:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_control_sets_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Control Sets - Place Design" -objects $obj
set_property -name "options.verbose" -value "1" -objects $obj
set_property -name "options.cells" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_place_report_incremental_reuse_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_0] "" ] } {
create_report_config -report_name impl_1_place_report_incremental_reuse_0 -report_type report_incremental_reuse:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Incremental Reuse - Place Design" -objects $obj
set_property -name "options.cells" -value "" -objects $obj
set_property -name "options.hierarchical" -value "0" -objects $obj
set_property -name "options.hierarchical_depth" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_place_report_incremental_reuse_1' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_1] "" ] } {
create_report_config -report_name impl_1_place_report_incremental_reuse_1 -report_type report_incremental_reuse:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_incremental_reuse_1]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Incremental Reuse - Place Design" -objects $obj
set_property -name "options.cells" -value "" -objects $obj
set_property -name "options.hierarchical" -value "0" -objects $obj
set_property -name "options.hierarchical_depth" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_place_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_place_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps place_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_place_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Timing Summary - Place Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_post_place_power_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_post_place_power_opt_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_post_place_power_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps post_place_power_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_post_place_power_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Timing Summary - Post-Place Power Opt Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_phys_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_phys_opt_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_phys_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps phys_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_phys_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "0" -objects $obj
set_property -name "display_name" -value "Timing Summary - Post-Place Phys Opt Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_drc_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_drc_0] "" ] } {
create_report_config -report_name impl_1_route_report_drc_0 -report_type report_drc:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_drc_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "DRC - Route Design" -objects $obj
set_property -name "options.upgrade_cw" -value "0" -objects $obj
set_property -name "options.checks" -value "" -objects $obj
set_property -name "options.ruledecks" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_methodology_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_methodology_0] "" ] } {
create_report_config -report_name impl_1_route_report_methodology_0 -report_type report_methodology:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_methodology_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Methodology - Route Design" -objects $obj
set_property -name "options.checks" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_power_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_power_0] "" ] } {
create_report_config -report_name impl_1_route_report_power_0 -report_type report_power:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_power_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Power - Route Design" -objects $obj
set_property -name "options.advisory" -value "0" -objects $obj
set_property -name "options.xpe" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_route_status_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_route_status_0] "" ] } {
create_report_config -report_name impl_1_route_report_route_status_0 -report_type report_route_status:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_route_status_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Route Status - Route Design" -objects $obj
set_property -name "options.of_objects" -value "" -objects $obj
set_property -name "options.route_type" -value "" -objects $obj
set_property -name "options.list_all_nets" -value "0" -objects $obj
set_property -name "options.show_all" -value "0" -objects $obj
set_property -name "options.has_routing" -value "0" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_route_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Timing Summary - Route Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "0" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_incremental_reuse_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_incremental_reuse_0] "" ] } {
create_report_config -report_name impl_1_route_report_incremental_reuse_0 -report_type report_incremental_reuse:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_incremental_reuse_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Incremental Reuse - Route Design" -objects $obj
set_property -name "options.cells" -value "" -objects $obj
set_property -name "options.hierarchical" -value "0" -objects $obj
set_property -name "options.hierarchical_depth" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_clock_utilization_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_clock_utilization_0] "" ] } {
create_report_config -report_name impl_1_route_report_clock_utilization_0 -report_type report_clock_utilization:1.0 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_clock_utilization_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Clock Utilization - Route Design" -objects $obj
set_property -name "options.write_xdc" -value "0" -objects $obj
set_property -name "options.clock_roots_only" -value "0" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_route_report_bus_skew_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_bus_skew_0] "" ] } {
create_report_config -report_name impl_1_route_report_bus_skew_0 -report_type report_bus_skew:1.1 -steps route_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_route_report_bus_skew_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Bus Skew - Route Design" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.slack_greater_than" -value "" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.warn_on_violation" -value "1" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_post_route_phys_opt_report_timing_summary_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_timing_summary_0] "" ] } {
create_report_config -report_name impl_1_post_route_phys_opt_report_timing_summary_0 -report_type report_timing_summary:1.0 -steps post_route_phys_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_timing_summary_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Timing Summary - Post-Route Phys Opt Design" -objects $obj
set_property -name "options.check_timing_verbose" -value "0" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "10" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.report_unconstrained" -value "0" -objects $obj
set_property -name "options.warn_on_violation" -value "1" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.cell" -value "" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
# Create 'impl_1_post_route_phys_opt_report_bus_skew_0' report (if not found)
if { [ string equal [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_bus_skew_0] "" ] } {
create_report_config -report_name impl_1_post_route_phys_opt_report_bus_skew_0 -report_type report_bus_skew:1.1 -steps post_route_phys_opt_design -runs impl_1
}
set obj [get_report_configs -of_objects [get_runs impl_1] impl_1_post_route_phys_opt_report_bus_skew_0]
if { $obj != "" } {
set_property -name "is_enabled" -value "1" -objects $obj
set_property -name "display_name" -value "Bus Skew - Post-Route Phys Opt Design" -objects $obj
set_property -name "options.delay_type" -value "" -objects $obj
set_property -name "options.setup" -value "0" -objects $obj
set_property -name "options.hold" -value "0" -objects $obj
set_property -name "options.max_paths" -value "" -objects $obj
set_property -name "options.nworst" -value "" -objects $obj
set_property -name "options.unique_pins" -value "0" -objects $obj
set_property -name "options.path_type" -value "" -objects $obj
set_property -name "options.slack_lesser_than" -value "" -objects $obj
set_property -name "options.slack_greater_than" -value "" -objects $obj
set_property -name "options.significant_digits" -value "" -objects $obj
set_property -name "options.warn_on_violation" -value "1" -objects $obj
set_property -name "options.more_options" -value "" -objects $obj
}
set obj [get_runs impl_1]
set_property -name "constrset" -value "constrs_1" -objects $obj
set_property -name "description" -value "Default settings for Implementation." -objects $obj
set_property -name "flow" -value "Vivado Implementation 2018" -objects $obj
set_property -name "name" -value "impl_1" -objects $obj
set_property -name "needs_refresh" -value "0" -objects $obj
set_property -name "pr_configuration" -value "" -objects $obj
set_property -name "srcset" -value "sources_1" -objects $obj
set_property -name "incremental_checkpoint" -value "" -objects $obj
set_property -name "auto_incremental_checkpoint" -value "0" -objects $obj
set_property -name "incremental_checkpoint.directive" -value "" -objects $obj
set_property -name "rqs_files" -value "" -objects $obj
set_property -name "ml_strategy_runs" -value "" -objects $obj
set_property -name "auto_rqs" -value "0" -objects $obj
set_property -name "auto_rqs.directory" -value "$proj_dir/ultra96_design.srcs/utils_1/imports/impl_1" -objects $obj
set_property -name "incremental_checkpoint.more_options" -value "" -objects $obj
set_property -name "include_in_archive" -value "1" -objects $obj
set_property -name "gen_full_bitstream" -value "1" -objects $obj
set_property -name "auto_incremental_checkpoint.directory" -value "$proj_dir/ultra96_design.srcs/utils_1/imports/impl_1" -objects $obj
set_property -name "min_rqa_score" -value "0" -objects $obj
set_property -name "strategy" -value "Vivado Implementation Defaults" -objects $obj
set_property -name "steps.init_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.init_design.tcl.post" -value "" -objects $obj
set_property -name "steps.init_design.args.more options" -value "" -objects $obj
set_property -name "steps.opt_design.is_enabled" -value "1" -objects $obj
set_property -name "steps.opt_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.opt_design.tcl.post" -value "" -objects $obj
set_property -name "steps.opt_design.args.verbose" -value "0" -objects $obj
set_property -name "steps.opt_design.args.directive" -value "Default" -objects $obj
set_property -name "steps.opt_design.args.more options" -value "" -objects $obj
set_property -name "steps.power_opt_design.is_enabled" -value "0" -objects $obj
set_property -name "steps.power_opt_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.power_opt_design.tcl.post" -value "" -objects $obj
set_property -name "steps.power_opt_design.args.more options" -value "" -objects $obj
set_property -name "steps.place_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.place_design.tcl.post" -value "" -objects $obj
set_property -name "steps.place_design.args.directive" -value "Default" -objects $obj
set_property -name "steps.place_design.args.more options" -value "" -objects $obj
set_property -name "steps.post_place_power_opt_design.is_enabled" -value "0" -objects $obj
set_property -name "steps.post_place_power_opt_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.post_place_power_opt_design.tcl.post" -value "" -objects $obj
set_property -name "steps.post_place_power_opt_design.args.more options" -value "" -objects $obj
set_property -name "steps.phys_opt_design.is_enabled" -value "0" -objects $obj
set_property -name "steps.phys_opt_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.phys_opt_design.tcl.post" -value "" -objects $obj
set_property -name "steps.phys_opt_design.args.directive" -value "Default" -objects $obj
set_property -name "steps.phys_opt_design.args.more options" -value "" -objects $obj
set_property -name "steps.route_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.route_design.tcl.post" -value "" -objects $obj
set_property -name "steps.route_design.args.directive" -value "Default" -objects $obj
set_property -name "steps.route_design.args.more options" -value "" -objects $obj
set_property -name "steps.post_route_phys_opt_design.is_enabled" -value "0" -objects $obj
set_property -name "steps.post_route_phys_opt_design.tcl.pre" -value "" -objects $obj
set_property -name "steps.post_route_phys_opt_design.tcl.post" -value "" -objects $obj
set_property -name "steps.post_route_phys_opt_design.args.directive" -value "Default" -objects $obj
set_property -name "steps.post_route_phys_opt_design.args.more options" -value "" -objects $obj
set_property -name "steps.write_bitstream.tcl.pre" -value "" -objects $obj
set_property -name "steps.write_bitstream.tcl.post" -value "" -objects $obj
set_property -name "steps.write_bitstream.args.raw_bitfile" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.mask_file" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.no_binary_bitfile" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.bin_file" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.readback_file" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.logic_location_file" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.verbose" -value "0" -objects $obj
set_property -name "steps.write_bitstream.args.more options" -value "" -objects $obj
# set the current impl run
current_run -implementation [get_runs impl_1]
catch {
if { $idrFlowPropertiesConstraints != {} } {
set_param runs.disableIDRFlowPropertyConstraints $idrFlowPropertiesConstraints
}
}
puts "INFO: Project created:${_xil_proj_name_}"
# Create 'drc_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets [ list "drc_1" ] ] ""]} {
create_dashboard_gadget -name {drc_1} -type drc
}
set obj [get_dashboard_gadgets [ list "drc_1" ] ]
set_property -name "active_reports" -value "" -objects $obj
set_property -name "active_reports_invalid" -value "" -objects $obj
set_property -name "active_run" -value "0" -objects $obj
set_property -name "hide_unused_data" -value "1" -objects $obj
set_property -name "incl_new_reports" -value "0" -objects $obj
set_property -name "reports" -value "impl_1#impl_1_route_report_drc_0" -objects $obj
set_property -name "run.step" -value "route_design" -objects $obj
set_property -name "run.type" -value "implementation" -objects $obj
set_property -name "statistics.critical_warning" -value "1" -objects $obj
set_property -name "statistics.error" -value "1" -objects $obj
set_property -name "statistics.info" -value "1" -objects $obj
set_property -name "statistics.warning" -value "1" -objects $obj
set_property -name "view.orientation" -value "Horizontal" -objects $obj
set_property -name "view.type" -value "Graph" -objects $obj
# Create 'methodology_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets [ list "methodology_1" ] ] ""]} {
create_dashboard_gadget -name {methodology_1} -type methodology
}
set obj [get_dashboard_gadgets [ list "methodology_1" ] ]
set_property -name "active_reports" -value "" -objects $obj
set_property -name "active_reports_invalid" -value "" -objects $obj
set_property -name "active_run" -value "0" -objects $obj
set_property -name "hide_unused_data" -value "1" -objects $obj
set_property -name "incl_new_reports" -value "0" -objects $obj
set_property -name "reports" -value "impl_1#impl_1_route_report_methodology_0" -objects $obj
set_property -name "run.step" -value "route_design" -objects $obj
set_property -name "run.type" -value "implementation" -objects $obj
set_property -name "statistics.critical_warning" -value "1" -objects $obj
set_property -name "statistics.error" -value "1" -objects $obj
set_property -name "statistics.info" -value "1" -objects $obj
set_property -name "statistics.warning" -value "1" -objects $obj
set_property -name "view.orientation" -value "Horizontal" -objects $obj
set_property -name "view.type" -value "Graph" -objects $obj
# Create 'power_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets [ list "power_1" ] ] ""]} {
create_dashboard_gadget -name {power_1} -type power
}
set obj [get_dashboard_gadgets [ list "power_1" ] ]
set_property -name "active_reports" -value "" -objects $obj
set_property -name "active_reports_invalid" -value "" -objects $obj
set_property -name "active_run" -value "0" -objects $obj
set_property -name "hide_unused_data" -value "1" -objects $obj
set_property -name "incl_new_reports" -value "0" -objects $obj
set_property -name "reports" -value "impl_1#impl_1_route_report_power_0" -objects $obj
set_property -name "run.step" -value "route_design" -objects $obj
set_property -name "run.type" -value "implementation" -objects $obj
set_property -name "statistics.bram" -value "1" -objects $obj
set_property -name "statistics.clocks" -value "1" -objects $obj
set_property -name "statistics.dsp" -value "1" -objects $obj
set_property -name "statistics.gth" -value "1" -objects $obj
set_property -name "statistics.gtp" -value "1" -objects $obj
set_property -name "statistics.gtx" -value "1" -objects $obj
set_property -name "statistics.gtz" -value "1" -objects $obj
set_property -name "statistics.io" -value "1" -objects $obj
set_property -name "statistics.logic" -value "1" -objects $obj
set_property -name "statistics.mmcm" -value "1" -objects $obj
set_property -name "statistics.pcie" -value "1" -objects $obj
set_property -name "statistics.phaser" -value "1" -objects $obj
set_property -name "statistics.pll" -value "1" -objects $obj
set_property -name "statistics.pl_static" -value "1" -objects $obj
set_property -name "statistics.ps7" -value "1" -objects $obj
set_property -name "statistics.ps" -value "1" -objects $obj
set_property -name "statistics.ps_static" -value "1" -objects $obj
set_property -name "statistics.signals" -value "1" -objects $obj
set_property -name "statistics.total_power" -value "1" -objects $obj
set_property -name "statistics.transceiver" -value "1" -objects $obj
set_property -name "statistics.xadc" -value "1" -objects $obj
set_property -name "view.orientation" -value "Horizontal" -objects $obj
set_property -name "view.type" -value "Graph" -objects $obj
# Create 'timing_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets [ list "timing_1" ] ] ""]} {
create_dashboard_gadget -name {timing_1} -type timing
}
set obj [get_dashboard_gadgets [ list "timing_1" ] ]
set_property -name "active_reports" -value "" -objects $obj
set_property -name "active_reports_invalid" -value "" -objects $obj
set_property -name "active_run" -value "0" -objects $obj
set_property -name "hide_unused_data" -value "1" -objects $obj
set_property -name "incl_new_reports" -value "0" -objects $obj
set_property -name "reports" -value "impl_1#impl_1_route_report_timing_summary_0" -objects $obj
set_property -name "run.step" -value "route_design" -objects $obj
set_property -name "run.type" -value "implementation" -objects $obj
set_property -name "statistics.ths" -value "1" -objects $obj
set_property -name "statistics.tns" -value "1" -objects $obj
set_property -name "statistics.tpws" -value "1" -objects $obj
set_property -name "statistics.wbss" -value "1" -objects $obj
set_property -name "statistics.whs" -value "1" -objects $obj
set_property -name "statistics.wns" -value "1" -objects $obj
set_property -name "view.orientation" -value "Horizontal" -objects $obj
set_property -name "view.type" -value "Table" -objects $obj
# Create 'utilization_1' gadget (if not found)
if {[string equal [get_dashboard_gadgets [ list "utilization_1" ] ] ""]} {
create_dashboard_gadget -name {utilization_1} -type utilization
}
set obj [get_dashboard_gadgets [ list "utilization_1" ] ]
set_property -name "active_reports" -value "" -objects $obj
set_property -name "active_reports_invalid" -value "" -objects $obj
set_property -name "active_run" -value "0" -objects $obj
set_property -name "hide_unused_data" -value "1" -objects $obj
set_property -name "incl_new_reports" -value "0" -objects $obj
set_property -name "reports" -value "synth_1#synth_1_synth_report_utilization_0" -objects $obj
set_property -name "run.step" -value "synth_design" -objects $obj
set_property -name "run.type" -value "synthesis" -objects $obj
set_property -name "statistics.bram" -value "1" -objects $obj
set_property -name "statistics.bufg" -value "1" -objects $obj
set_property -name "statistics.dsp" -value "1" -objects $obj
set_property -name "statistics.ff" -value "1" -objects $obj
set_property -name "statistics.gt" -value "1" -objects $obj
set_property -name "statistics.io" -value "1" -objects $obj
set_property -name "statistics.lut" -value "1" -objects $obj
set_property -name "statistics.lutram" -value "1" -objects $obj
set_property -name "statistics.mmcm" -value "1" -objects $obj
set_property -name "statistics.pcie" -value "1" -objects $obj
set_property -name "statistics.pll" -value "1" -objects $obj
set_property -name "statistics.uram" -value "1" -objects $obj
set_property -name "view.orientation" -value "Horizontal" -objects $obj
set_property -name "view.type" -value "Graph" -objects $obj
# Create 'utilization_2' gadget (if not found)
if {[string equal [get_dashboard_gadgets [ list "utilization_2" ] ] ""]} {
create_dashboard_gadget -name {utilization_2} -type utilization
}
set obj [get_dashboard_gadgets [ list "utilization_2" ] ]
set_property -name "active_reports" -value "" -objects $obj
set_property -name "active_reports_invalid" -value "" -objects $obj
set_property -name "active_run" -value "0" -objects $obj
set_property -name "hide_unused_data" -value "1" -objects $obj
set_property -name "incl_new_reports" -value "0" -objects $obj
set_property -name "reports" -value "impl_1#impl_1_place_report_utilization_0" -objects $obj
set_property -name "run.step" -value "place_design" -objects $obj
set_property -name "run.type" -value "implementation" -objects $obj
set_property -name "statistics.bram" -value "1" -objects $obj
set_property -name "statistics.bufg" -value "1" -objects $obj
set_property -name "statistics.dsp" -value "1" -objects $obj
set_property -name "statistics.ff" -value "1" -objects $obj
set_property -name "statistics.gt" -value "1" -objects $obj
set_property -name "statistics.io" -value "1" -objects $obj
set_property -name "statistics.lut" -value "1" -objects $obj
set_property -name "statistics.lutram" -value "1" -objects $obj
set_property -name "statistics.mmcm" -value "1" -objects $obj
set_property -name "statistics.pcie" -value "1" -objects $obj
set_property -name "statistics.pll" -value "1" -objects $obj
set_property -name "statistics.uram" -value "1" -objects $obj
set_property -name "view.orientation" -value "Horizontal" -objects $obj
set_property -name "view.type" -value "Graph" -objects $obj
move_dashboard_gadget -name {utilization_1} -row 0 -col 0
move_dashboard_gadget -name {power_1} -row 1 -col 0
move_dashboard_gadget -name {drc_1} -row 2 -col 0
move_dashboard_gadget -name {timing_1} -row 0 -col 1
move_dashboard_gadget -name {utilization_2} -row 1 -col 1
move_dashboard_gadget -name {methodology_1} -row 2 -col 1
@xerpi
Copy link
Author

xerpi commented Sep 12, 2022

More information here: https://github.com/xerpi/ultra96v2_mipi_csi_imx219

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment