linino_openwrt_reboot.log

linino_openwrt_reboot.log

U-Boot 1.1.5-linino-g2d891225 (Nov 22 2017 - 09:06:12)

Linino Board (ar9331) U-boot
DRAM:  64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 218k for U-Boot at: 83fc8000
Reserving 192k for malloc() at: 83f98000
Reserving 44 Bytes for Board Info at: 83f97fd4
Reserving 36 Bytes for Global Data at: 83f97fb0
Reserving 128k for boot params() at: 83f77fb0
Stack Pointer at: 83f77f98
Now running in RAM - U-Boot at: 83fc8000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16777216, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   eth0: b4:21:8a:00:00:00
eth1: b4:21:8a:00:00:01
eth0, eth1
autoboot in 4 seconds (stop with 'ard')...
## Booting image at 9f050000 ...
   Image Name:   MIPS OpenWrt Linux-6.6.86
   Created:      2025-04-13  16:38:32 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2613702 Bytes =  2.5 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9f050040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

[    0.000000] Linux version 6.6.86 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28597-0425664679) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Sun Apr 13 16:38:32 2025
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] MIPS: machine is Arduino Yun
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Kernel command line: console=ttyATH0,250000 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 55064K/65536K available (6821K kernel code, 602K rwdata, 900K rodata, 1204K init, 233K bss, 10472K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 400.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000003] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.003796] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.078212] pid_max: default: 32768 minimum: 301
[    0.100016] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.102764] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.122848] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[    0.134730] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.138721] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.146900] pinctrl core: initialized pinctrl subsystem
[    0.154051] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.157162] thermal_sys: Registered thermal governor 'step_wise'
[    0.160437] /ahb/apb: Fixed dependency cycle(s) with /ahb/apb/interrupt-controller@18060010
[    0.168280] /ahb/apb/pinmux@18040028: Fixed dependency cycle(s) with /ahb/apb/pinmux@18040028/pinmux_switch_led_disable_pins
[    0.172920] /ahb/apb/pinmux@18040028: Fixed dependency cycle(s) with /ahb/apb/pinmux@18040028/pinmux_jtag_disable_pins
[    0.178607] /ahb/apb/pinmux@18040030: Fixed dependency cycle(s) with /ahb/apb/pinmux@18040030/pinmux_enable_gpio11
[    0.183061] /ahb/apb/pinmux@180600ac: Fixed dependency cycle(s) with /ahb/apb/pinmux@180600ac/pinmux_enable_gpio26_gpio27
[    0.209781] clocksource: Switched to clocksource MIPS
[    0.232558] NET: Registered PF_INET protocol family
[    0.234581] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.240252] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.243573] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.247101] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.250697] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.253895] TCP: Hash tables configured (established 1024 bind 1024)
[    0.258042] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.261354] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.263779] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.268640] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.270768] PCI: CLS 0 bytes, default 32
[    0.280240] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.285847] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.287902] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.307442] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.312988] pinctrl-single 18040028.pinmux: 64 pins, size 8
[    0.315837] pinctrl-single 18040030.pinmux: 32 pins, size 4
[    0.318532] pinctrl-single 180600ac.pinmux: 32 pins, size 4
[    0.322121] gpio-export gpio-export: 3 gpio(s) exported
[    0.325657] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.337600] 18020000.uart: ttyATH0 at MMIO 0x18020000 (irq = 10, base_baud = 1562500) is a Ar933X UART
[    0.341519] printk: console [ttyATH0] enabled
[    0.341519] printk: console [ttyATH0] enabled
[    0.345271] printk: bootconsole [early0] disabled
[    0.345271] printk: bootconsole [early0] disabled
[    0.408494] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    0.410387] 5 fixed-partitions partitions found on MTD device spi0.0
[    0.413050] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.416053] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.419466] Creating 5 MTD partitions on "spi0.0":
[    0.421363] 0x000000000000-0x000000040000 : "u-boot"
[    0.429099] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.434427] 0x000000050000-0x000000fe0000 : "firmware"
[    0.439740] 2 uimage-fw partitions found on MTD device firmware
[    0.441934] Creating 2 MTD partitions on "firmware":
[    0.444213] 0x000000000000-0x000000280000 : "kernel"
[    0.449860] 0x000000280000-0x000000f90000 : "rootfs"
[    0.454794] mtd: setting mtd4 (rootfs) as root device
[    0.456593] 1 squashfs-split partitions found on MTD device rootfs
[    0.459347] 0x000000660000-0x000000f90000 : "rootfs_data"
[    0.465186] 0x000000fe0000-0x000000ff0000 : "nvram"
[    0.470259] 0x000000ff0000-0x000001000000 : "art"
[    0.475387] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.839930] switch0: Atheros AR724X/AR933X built-in rev. 2 switch registered on mdio.0
[    0.885884] ag71xx-legacy 19000000.eth: invalid MAC address, using random address
[    1.300442] ag71xx-legacy 19000000.eth: connected to PHY at mdio.0:1f:04 [uid=004dd041, driver=Qualcomm Atheros AR9331 built-in PHY]
[    1.306497] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
[    1.309459] i2c_dev: i2c /dev entries driver
[    1.316100] NET: Registered PF_INET6 protocol family
[    1.333256] Segment Routing with IPv6
[    1.334451] In-situ OAM (IOAM) with IPv6
[    1.336377] NET: Registered PF_PACKET protocol family
[    1.338512] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.344935] 8021q: 802.1Q VLAN Support v1.8
[    1.408599] clk: Disabling unused clock?H?[    1.421829] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.433683] Freeing unused kernel image (initmem) memory: 1204K
[    1.435774] This architecture does not have kernel memory protection.
[    1.438749] Run /sbin/init as init process
[    2.441733] init: Console is alive
[    2.443302] init: - watchdog -
[    4.518478] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.640215] usbcore: registered new interface driver usbfs
[    4.642283] usbcore: registered new interface driver hub
[    4.644698] usbcore: registered new device driver usb
[    4.674830] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    4.710601] ci_hdrc ci_hdrc.0: EHCI Host Controller
[    4.712317] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[    4.739792] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[    4.743313] hub 1-0:1.0: USB hub found
[    4.745946] hub 1-0:1.0: 1 port detected
[    4.772296] SCSI subsystem initialized
[    4.789925] usbcore: registered new interface driver usb-storage
[    4.794306] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.803444] init: - preinit -
[    5.250686] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[    5.691876] hub 1-1:1.0: USB hub found
[    5.693455] hub 1-1:1.0: 4 ports detected
[    6.109937] usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
[    6.412095] usb 1-1.4: new high-speed USB device number 4 using ci_hdrc
[    6.574893] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    6.598310] scsi host0: usb-storage 1-1.4:1.0
[    7.691210] scsi 0:0:0:0: Direct-Access     Multi    Flash Reader     1.00 PQ: 0 ANSI: 0
[    7.701334] sd 0:0:0:0: [sda] Media removed, stopped polling
[    7.704382] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    8.059841] random: crng init done
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.651610] eth0: link up (100Mbps/Full duplex)
[   13.977255] mount_root: loading kmods from internal overlay
[   14.022857] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   14.031980] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   14.501346] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[   14.504532] block: unable to load configuration (fstab: Entry not found)
[   14.507436] block: attempting to load /tmp/overlay/etc/config/fstab
[   14.511435] block: unable to load configuration (fstab: Entry not found)
[   14.514331] block: attempting to load /etc/config/fstab
[   14.516950] block: unable to load configuration (fstab: Entry not found)
[   14.520075] block: no usable configuration
[   14.588203] jffs2: notice: (583) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (0 unchecked, 6 orphan) and 13 of xref (6 dead, 0 orphan) found.
[   14.595824] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   14.604078] block: extroot: not configured
[   14.674906] jffs2: notice: (581) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (0 unchecked, 6 orphan) and 13 of xref (6 dead, 0 orphan) found.
[   14.955660] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[   14.963111] block: extroot: not configured
[   14.965731] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   14.969707] block: extroot: not configured
[   14.973315] mount_root: switching to jffs2 overlay
[   14.978220] overlayfs: upper fs does not support tmpfile.
[   14.988717] urandom-seed: Seeding with /etc/urandom.seed
[   15.083765] eth0: link down
[   15.110782] procd: - early -
[   15.111995] procd: - watchdog -
[   15.968703] procd: - watchdog -
[   15.973534] procd: - ubus -
[   16.231635] procd: - init -
Please press Enter to activate this console.
[   19.668505] kmodloader: loading kernel modules from /etc/modules.d/*
[   21.106387] jitterentropy: Initialization failed with host not compliant with requirements: 9
[   21.999245] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[   22.002159] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[   23.404628] PPP generic driver version 2.4.2
[   23.432704] NET: Registered PF_PPPOX protocol family
[   23.656087] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xec07d69b, irq=2
[   24.303127] jitterentropy: Initialization failed with host not compliant with requirements: 9
[   25.170466] kmodloader: 1 module could not be probed
[   25.172574] kmodloader: - jitterentropy_rng - 0
[   26.620638] urngd: v1.0.2 started.

login[981]: root login on 'ttyATH0'


BusyBox v1.36.1 (2025-04-13 16:38:32 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 24.10.1, r28597-0425664679
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWRT:~#