3D Printer settings

print.json

{
	"printer_type_id": "26",
	"layer_height": "0.2",
	"wall_thickness": "0.8",
	"nozzle_size": "0.4",
	"bottom_thickness": "0.2",
	"filament_diameter": "1.75",
	"filament_flow": "120",
	"solid_top": "1",
	"solid_bottom": "1",
	"solid_layer_thickness": "0.8",
	"fill_overlap": "15",
	"bottom_layer_speed": "20",
	"print_speed": "20",
	"infill_speed": "20",
	"travel_speed": "80",
	"fan_enabled": "1",
	"fan_speed": "100",
	"fan_speed_max": "75",
	"support": "Everywhere",
	"support_type": "Lines",
	"support_angle": "60",
	"support_fill_rate": "15",
	"support_xy_distance": "0.7",
	"support_z_distance": "0.15",
	"retraction_enable": "1",
	"retraction_amount": "5",
	"retraction_speed": "40",
	"retraction_min_travel": "1.5",
	"retraction_dual_amount": "16.5",
	"retraction_minimal_extrusion": "0.02",
	"retraction_combing": "1",
	"overlap_dual": "0.15",
	"cool_min_layer_time": "8",
	"cool_min_feedrate": "10",
	"cool_head_lift": "1",
	"fan_full_height": "5",
	"fill_density": "20",
	"platform_adhesion": "None",
	"skirt_gap": "3",
	"skirt_line_count": "3",
	"skirt_minimal_length": "150",
	"brim_line_count": "0",
	"raft_margin": "5",
	"raft_line_spacing": "3",
	"raft_base_thickness": "0.6",
	"raft_base_linewidth": "1.2",
	"raft_interface_thickness": "0.35",
	"raft_interface_linewidth": "0.6",
	"raft_airgap": "0.2",
	"raft_surface_layers": "1",
	"object_sink": "0",
	"layer0_width_factor": "100",
	"print_bed_temperature": "60",
	"print_temperature": "195",
	"extruderOffset[1": "0",
	"posx": "100000",
	"posy": "100000",
	"extra": "-m 1.0,0.0,0.0,0.0,1.0,0.0,0.0,0.0,1.0",
	"startCode": "M140 S{print_bed_temperature}\nM190 S{print_bed_temperature}\nM109 T0 S{print_temperature}\nT0\nG21\nG90\nM82\nM107\nG28 X0 Y0\nG28 Z0\nG1 Z0.3 F9000\nG92 E0\nG1 X25 Y25 E10 F200\nG92 E0\nG1 F9000\nM117 Printing...",
	"endCode": "M104 S0\nM140 S0\nG91\nG1 E-1 F300\nG1 Z+0.5 E-5 X-20 Y-20 F9000\nG28 X0 Y0\nM84\nG90\nM107",
	"printer_template_id": "4240",
	"material_price": "0.23",
	"hourly_deprecation_cost": "2",
	"flat_fee": "0",
	"material_name": "PLA",
	"material_density": "1.25"
}