eqhmcow

# /etc/iptables.rules

# Generated by iptables-save v1.6.1 on Sat Oct 19 09:21:09 2019
*mangle
:PREROUTING ACCEPT [0:0]
:INPUT ACCEPT [0:0]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [0:0]
:POSTROUTING ACCEPT [0:0]
:MINIUPNPD - [0:0]

researcx

24bit 192 kHz HD Audio + A=432 Hz Tuning + Equalizer

High-quality sampling

ALSA

echo 'defaults.pcm.rate_converter "speexrate_best"' | tee -a .asoundrc
sudo alsactl restore

PulseAudio

sudo echo 'default-sample-format = s24le' | sudo tee -a /etc/pulse/daemon.conf
sudo echo 'default-sample-rate = 192000' | sudo tee -a /etc/pulse/daemon.conf

Thermi

Best Practices:

1. Don't use iptables to apply your rules one at a time, use iptables-restore to apply a whole ruleset in one action.
2. Set your INPUT and FORWARD policy to DROP.
3. Don't set your OUTPUT policy to DROP unless you really know what you're doing.
4. If you're going to implement a blacklist or whitelist, you should look at using ipsets if that list is going to be more than two or three addresses, and if it might be dynamic.
5. Allow all traffic on lo.
6. You should ALLOW traffic in ctstates of RELATED and ESTABLISHED near the beginning of your rules
7. Don't use iptables -L
8. DON'T USE IPTABLES -L
9. Use iptables-save instead of iptables -L.

nickfox-taterli

sudo sync
sudo apt-get update
sudo apt-get -y upgrade
sudo apt-get -y dist-upgrade
sudo sed -i 's/jessie/buster/g' /etc/apt/sources.list
sudo apt-get update
sudo apt-get -y upgrade
sudo apt-get -y dist-upgrade
sudo sync
#sudo reboot

sultanqasim

#!/bin/bash

# Raspberry Pi ZRAM script
# Tuned for quad core, 1 GB RAM models
# put me in /etc/init.d/zram.sh and make me executable
# then run "sudo update-rc.d zram.sh defaults"

modprobe zram
echo 3 >/sys/devices/virtual/block/zram0/max_comp_streams
echo lz4 >/sys/devices/virtual/block/zram0/comp_algorithm

nonakap

# for NEC Express5800/S70 type hf
# FAN1: front, FAN2: CPU, FAN3: rear
INTERVAL=5
DEVPATH=hwmon1=devices/platform/coretemp.0 hwmon2=devices/platform/w83627ehf.2608
DEVNAME=hwmon1=coretemp hwmon2=nct6776
FCTEMPS=hwmon2/device/pwm3=hwmon1/device/temp1_input hwmon2/device/pwm2=hwmon1/device/temp1_input hwmon2/device/pwm1=hwmon1/device/temp1_input
FCFANS=hwmon2/device/pwm3=hwmon2/device/fan3_input hwmon2/device/pwm2=hwmon2/device/fan2_input hwmon2/device/pwm1=hwmon2/device/fan1_input
MINTEMP=hwmon2/device/pwm3=38 hwmon2/device/pwm2=33 hwmon2/device/pwm1=33
MAXTEMP=hwmon2/device/pwm3=73 hwmon2/device/pwm2=73 hwmon2/device/pwm1=73
MINSTART=hwmon2/device/pwm3=10 hwmon2/device/pwm2=50 hwmon2/device/pwm1=50

gorakhargosh

// Sample pdnsd configuration file. Must be customized to obtain a working pdnsd setup!
// Read the pdnsd.conf(5) manpage for an explanation of the options.
// Add or remove '#' in front of options you want to disable or enable, respectively.
// Remove '/*' and '*/' to enable complete sections.

global {
	perm_cache=999999;
	cache_dir="/usr/local/var/cache/pdnsd";
#	pid_file = /var/run/pdnsd.pid;
	run_as="nobody";

bradoaks

#!/bin/bash

# As the "bufferbloat" folks have recently re-discovered and/or more widely
# publicized, congestion avoidance algorithms (such as those found in TCP) do
# a great job of allowing network endpoints to negotiate transfer rates that
# maximize a link's bandwidth usage without unduly penalizing any particular
# stream. This allows bulk transfer streams to use the maximum available
# bandwidth without affecting the latency of non-bulk (e.g. interactive)
# streams.

eqhmcow

#!/bin/bash

# As the "bufferbloat" folks have recently re-discovered and/or more widely
# publicized, congestion avoidance algorithms (such as those found in TCP) do
# a great job of allowing network endpoints to negotiate transfer rates that
# maximize a link's bandwidth usage without unduly penalizing any particular
# stream. This allows bulk transfer streams to use the maximum available
# bandwidth without affecting the latency of non-bulk (e.g. interactive)
# streams.