iomega_ez.out

gistfile1.txt

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: WDC WD40EFRX-68N32N0                     Firm: 82.00A82 Ser#:      WD-WCC7K7ELYE7A
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (-775897424 x 512)


IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK

IDE read: device 0 block # 8192, count 8192 ... 8192 blocks read: OK
## Booting image at 00040000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2019-06-17  14:11:42 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2389716 Bytes =  2.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
   Image Name:
   Created:      2019-06-17  15:39:40 UTC
   Image Type:   ARM Linux RAMDisk Image (bzip2 compressed)
   Data Size:    2983994 Bytes =  2.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Linux version 2.6.31.8 ([email protected]) (gcc version 4.7.2 (crosstool-NG 1.20.0) ) Mon Jun 17 10:11:37 EDT 2019 v0.0.9 Mon Jun 17 10:11:37 EDT 2019
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 114844KB available (4364K code, 319K data, 136K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
   arm4regs  :  1019.200 MB/sec
   8regs     :   635.200 MB/sec
   32regs    :   840.400 MB/sec
xor: using function: arm4regs (1019.200 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size   1MB
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP  Soc: 88F6282 A1 LE

 Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c403e740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1    107 MB/s
raid6: int32x2    124 MB/s
raid6: int32x4    124 MB/s
raid6: int32x8    121 MB/s
raid6: using algorithm int32x4 (124 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2912K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000ed20)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering unionfs 2.5.11 (for 2.6.31.14)
Installing knfsd (copyright (C) 1996 [email protected]).
msgmni has been set to 230
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     WDC      WD40EFRX-68N32N0 82.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 2 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Proc tool API enabled
  o Rx descripors: q0=256
  o Tx descripors: q0=532
  o Loading network interface(s):
     o register under mv88fx_eth platform
     o eth0, ifindex = 2, GbE port = 0

Warning: Giga 1 is Powered Off

tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
 sda:
0x00000007e000-0x00000007f000 : "env2"
Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
 sda1 sda2 sda3
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
iBoard_model 1
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2023-04-24 23:38:59 UTC (1682379539)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: bzip2 image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
cat: can't open '/sys/class/block/sdb/removable': No such file or directory
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is hm3
mdadm: No devices to examine
cat: can't open '/sys/class/block///size': No such file or directory
Valid Disk 1 in md0:
Valid Disk 2 in md0:
USB Device node is /dev/sdb1
Checking to see the if the reset button is pressed or not
Checking for valid image on system
mdadm: /dev/md0 not identified in config file.
mdadm: md device /dev/md0 does not appear to be active.
md: md0 stopped.
mdadm: stopped /dev/md0
mdadm: /dev/md0 not identified in config file.
  No volume groups found
e2fsck 1.42.5 (29-Jul-2012)
ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/md0_vg/BFDlv is mounted.
e2fsck: No such file or directory while trying to open /dev/md0_vg/BFDlv
Possibly non-existent device?
mount: mounting /dev/md0_vg/BFDlv on sysroot/boot failed: No such file or directory
umount: can't umount /sysroot/boot: Invalid argument
Checking if there is an attached EMC Imager
mount: mounting /dev/sdb1 on /usb_drive failed: No such device or address
sh: bad number
No USB Imager and No valid image on system
Going in to Network Imaging Mode
umount: can't umount /dev/md0: Invalid argument
umount: can't umount /usb_drive: Invalid argument
umount: can't umount /sysroot/boot: Invalid argument
Enable Network eth0
eth0: started
udhcpc (v1.21.0) started
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
No lease, failing
eth0      Link encap:Ethernet  HWaddr 00:D0:B8:1D:1B:90
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11

mknod: /dev/zero: File exists
No need to create fw_env.config
Device Serial Num is 0,01GU3AW8/Mru9XLj10vG6yV49iEZijZQsnFvC3VctQuy2gHJIOkTi9X13h8lj0Q8bI,USAC0700DR,
Device Model- hm3
DEPP Client version: 1.02
INITRD Build version: 4.1.408.34845
Device: Socket Listening on: 2081
Mac address = 00:d0:b8:1d:1b:90
Send: Network is unreachable
The DEPP image copy was not successful.
Reboot the system.