Skip to content

Instantly share code, notes, and snippets.

@znz

znz/bluescreen-boot-from-hd0-2.txt

Created September 10, 2009 09:15
Show Gist options
  • Save znz/184435 to your computer and use it in GitHub Desktop.
Save znz/184435 to your computer and use it in GitHub Desktop.
Download ZIP
BSODの時のメッセージ
Raw
bluescreen-boot-from-hd0-2.txt
A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen,
restart your computer. If this screen appears again, follow
these steps:
Check for viruses on your computer. Remove any newly installed
hard drives or hard drive controllers. Check your hard drive
to make sure it is properly configured and terminated.
Run CHKDSK /F to check for hard drive corruption, and then
restart your computer.
Technical information:
*** STOP: 0x0000007B (0xF789EA98, 0xC0000034, 0x00000000, 0x00000000)
Raw
smartctl-a-dev-sda.txt
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MK1032GSX
Serial Number: 361I0832S
Firmware Version: AS021G
User Capacity: 100,030,242,816 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Sep 10 18:47:58 2009 JST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 384) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 76) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1968
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1720
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 1
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 066 066 000 Old_age Always - 13676
10 Spin_Retry_Count 0x0033 134 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1642
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 25
193 Load_Cycle_Count 0x0032 074 074 000 Old_age Always - 263364
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 52 (Lifetime Min/Max 7/81)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8420
222 Loaded_Hours 0x0032 072 072 000 Old_age Always - 11366
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 315
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 7487 hours (311 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 77 94 e2 e2 Error: UNC 8 sectors at LBA = 0x02e29477 = 48403575
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 ff 93 e2 e2 00 2d+02:39:31.908 READ DMA
ca 00 08 bf a9 a5 e8 00 2d+02:39:31.907 WRITE DMA
c8 00 08 67 1c 1e e5 00 2d+02:39:31.907 READ DMA
ca 00 80 3f a9 a5 e8 00 2d+02:39:31.906 WRITE DMA
c8 00 80 e7 1b 1e e5 00 2d+02:39:31.905 READ DMA
Error 3 occurred at disk power-on lifetime: 7487 hours (311 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 77 94 e2 e2 Error: UNC 8 sectors at LBA = 0x02e29477 = 48403575
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 ff 93 e2 e2 00 2d+02:28:23.748 READ DMA
ca 00 08 67 1c 1e e5 00 2d+02:28:23.748 WRITE DMA
c8 00 08 7f c6 e1 e7 00 2d+02:28:23.748 READ DMA
ca 00 80 e7 1b 1e e5 00 2d+02:28:23.747 WRITE DMA
c8 00 08 0f ec 12 e3 00 2d+02:28:23.737 READ DMA
Error 2 occurred at disk power-on lifetime: 7487 hours (311 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 77 94 e2 e2 Error: UNC 8 sectors at LBA = 0x02e29477 = 48403575
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 ff 93 e2 e2 00 2d+02:14:32.651 READ DMA
ca 00 08 7f c6 e1 e7 00 2d+02:14:32.650 WRITE DMA
c8 00 08 3f c6 5f e8 00 2d+02:14:32.649 READ DMA
ca 00 80 ff c5 e1 e7 00 2d+02:14:32.648 WRITE DMA
c8 00 80 bf c5 5f e8 00 2d+02:14:32.647 READ DMA
Error 1 occurred at disk power-on lifetime: 7487 hours (311 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 77 94 e2 e2 Error: UNC at LBA = 0x02e29477 = 48403575
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 03 80 ff 93 e2 e2 00 2d+02:01:14.306 READ MULTIPLE
c8 03 08 47 24 24 e2 00 2d+02:01:14.261 READ DMA
ca 03 01 1f 1a 0f e0 00 2d+02:01:14.261 WRITE DMA
ca 03 20 57 b6 01 e0 00 2d+02:01:14.261 WRITE DMA
ef 03 45 01 00 00 a0 00 2d+02:01:14.260 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment