vis-config

##Refresh rate of the visualizers. A really high refresh rate may cause screen tearing. Default is 20.
visualizer.fps=60

##Sets the audio sources to use. Currently available ones are "mpd" and "alsa"Sets the audio sources to use.
##Currently available ones are "mpd", "pulse" and "alsa". Defaults to "mpd".
#audio.sources=pulse

##vis tries to find the correct pulseaudio sink, however this will not work on all systems.
##If pulse audio is not working with vis try switching the audio source. A list can be found by running the
##command pacmd list-sinks  | grep -e 'name:'  -e 'index'
#audio.pulse.source=0

##Defaults to "/tmp/mpd.fifo"
#mpd.fifo.path=/tmp/mpd.fifo

##If set to false the visualizers will use mono mode instead of stereo. Some visualizers will
##behave differently when mono is enabled. For example, spectrum show two sets of bars.
#audio.stereo.enabled=false

##Specifies how often the visualizer will change in seconds. 0 means do not rotate. Default is 0.
#visualizer.rotation.secs=10

##Configures the samples rate and the cutoff frequencies.
#audio.sampling.frequency=44100
#audio.low.cutoff.frequency=22050
#audio.high.cutoff.frequency=30

##Applies scaling factor to both lorenz and ellipse visualizers. This is useful when the system audio is set
#to a low volume.
visualizer.scaling.multiplier=1.5

##Configures the visualizers and the order they are in. Available visualizers are spectrum,lorenz,ellipse.
##Defaults to spectrum,ellipse,lorenz
#visualizers=spectrum,ellipse,lorenz


##Configures what character the spectrum visualizer will use. Specifying a space (e.g " ") means the
##background will be colored instead of the character. Defaults to " ".
#visualizer.spectrum.character=#

##Spectrum bar width. Defaults to 2.
#visualizer.spectrum.bar.width=2

##The amount of space between each bar in the spectrum visualizer. Defaults to 1. It's possible to set this to
##zero to have no space between bars
#visualizer.spectrum.bar.spacing=1

##Available smoothing options are monstercat, sgs, none.
#visualizer.spectrum.smoothing.mode=sgs

##This configures the falloff effect on the spectrum visualizer. Available falloff options are fill,top,none.
##Defaults to "fill"
#visualizer.spectrum.falloff.mode=top

##Configures how fast the falloff character falls. This is an exponential falloff so values usually look
##best 0.9+ and small changes in this value can have a large effect. Defaults to 0.95
#visualizer.spectrum.falloff.weight=0.9

##Margins in percent of total screen for spectrum visualizer. All margins default to 0
#visualizer.spectrum.top.margin=0.30
#visualizer.spectrum.bottom.margin=0.10
#visualizer.spectrum.right.margin=0.10
#visualizer.spectrum.left.margin=0.10

##Reverses the direction of the spectrum so that high freqs are first and low freqs last. Defaults to false.
#visualizer.spectrum.reversed=false

##This configures the sgs smoothing effect on the spectrum visualizer. More points spreads out the smoothing
##effect and increasing passes runs the smoother multiple times on reach run. Defaults are points=3 and passes=1
#visualizer.sgs.smoothing.points=3
#visualizer.sgs.smoothing.passes=1


##Configures what character the ellipse visualizer will use. Specifying a space (e.g " ") means the
##background will be colored instead of the character. Defaults to "█".
#visualizer.ellipse.character=#

##The radius of each color ring in the ellipse visualizer. Defaults to 2.
#visualizer.ellipse.radius=2


##Configures what character the lorenz visualizer will use. Specifying a space (e.g " ") means the
##background will be colored instead of the character. Defaults to "█".
#visualizer.lorenz.character=#


##Turns off overriding the user's terminal colors. This is true by default.
#colors.override.terminal=false

##Specifies the color scheme. The color scheme must be in ~/.config/vis/colors/ directory. The default scheme is "colors".
colors.scheme=rainbow